Bogen HS30EZ Users Manual

Easy DesignTMSpeaker Model HS30EZ

Speaker Layout

The layout of the speakers should be planned prior to installation. Desired mounting height, barring obstructions, is 15 to 20 feet, with the speakers angled downward toward the listening area and facing in the same direction.

Layout starts in one corner of the area. The first speaker in Row 1 should be positioned 45 feet from the corner. The next speaker in Row 1 should be 90 feet from the first speaker (see Figure 1). Each additional speaker in the row should use this same spacing.

Row 2 starts 55 feet from Row 1 and, like Row 1, each speaker in Row 2 should be 90 feet apart.

Row 3 starts 55 feet from Row 2. Continue this pattern of alternating rows until area is covered.

For areas that include high shelving or corridors, speakers should be installed so that they project down the aisles between the shelves or down through the corridors.

The spacing of the speakers can be adjusted so that the speakers are evenly spaced in a row.

NOTE: Each environment is unique. This layout

plan is general in nature and may not be applicable for every installatio

Figure 1

START

HORN SPEAKER

Row 1

Row 2

Row 3

Row 4

45 ft. 90 ft. 55 ft. Full Clockwise

Figure 2

Very High Noise (85dB-95dB)

A B C Volume Setting

PLACEMENT

50 Spring Street, Ramsey NJ 07446

Tel. 201-934-8500 • Fax: 201-934-9832

www.bogen.com

Speaker Installation

STEP 1 - For easier installation, remove the flange (base) from

the speaker by unscrewing the wing nut while at the same time pressing inwardly on the wing nut. Place the flange flush with the mounting surface and mark the location of the three holes with either a marker or chisel. It is important that the three holes be exactly aligned with the flange, otherwise you might stress the base or make the connection unsteady. Drill the necessary holes and screw the flange to the surface (see Figure 3). (Use appro-

priate hardware for your specific mounting surface.)

NOTE:

The speaker may also be strap-mounted using standard

1/2-inch industrial strapping.

STEP 2 - After mounting the flange, reattach the speaker to the flange and aim the speaker for the desired coverage. A 45-degree downward angle is recommended, but this may vary depending upon speaker layout.

STEP 3 - Remove the plastic cover to make the electrical connection and set the volume control (see Figure 4). The suggested amplifier connections are:

Amplifier Outputs Speaker Connections

70V Terminal 1

COM Terminal 2

NOTE: The speaker will also work perfectly well with these

connections reversed. However, it is important to be consistent in the wiring of the speakers in the system.

STEP 4 - Adjust the volume control to the desired setting. See

Figure 2 for the suggested initial settings based on the ambient noise level of the environment. Place the plastic protective cover back over the exposed area.

NOTE:

The two furthermost clockwise settings (positions 7 & 8) on the volume control will produce the same volume.

Figure 4

ELECTRICAL CONNECTION

VOLUME CONTROL

Figure 3

The HS30EZ is warranted to be free from defects in material or workmanship from the date of sale to the original purchaser for the lifetime of the product. Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon

warranty, contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns require a Return Authorization number.

7/22/2008

Limited Warranty; Exclusion of Certain Damages