Bogen CAM8PRO User Manual

CAM8PRO Mixer

Installation and Use Manual

54-2034-01D 1207

Notice

Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. However, this information is subject to change.

Important Safety Information

Always follow these basic safety precautions when installing and using the unit:

1. Read all instructions before installing or operating the unit.

2. Follow all warnings and instructions marked on the product.

DO NOT block or cover the ventilation slots and openings

. They prevent the product from overheating. DO NOT place the product in a separate enclosure or cabinet, unless proper ventilation is provided.

4. Never spill liquid on the product or drop objects into the ventilation slots and openings. Doing so may result in serious damage to the components.

5. Repair or service must be performed by a factory authorized repair facility.

DO NOT use the product near water or in a wet or damp place (such as a wet basement).

7. DO NOT use extension cords. The product must be installed within 6 feet of a grounded outlet receptacle.

8. DO NOT install telephone wiring during a lightning storm.

9. DO NOT install telephone jacks in a wet location unless the jack is specifically designed for wet locations.

10. Never touch uninsulated wires or terminals, unless the line has been disconnected at the paging or controller interface.

11. Use caution when installing or modifying paging or control lines.

Maintenance & Service

Caution

There are no user-serviceable parts within the unit. Have all internal servicing performed by a qualified technician. The warranty will become void if repairs are made by other than the Bogen Service Department or an authorized service agency.

Our Applications Engineering Department is available to help you troubleshoot problems with your Bogen equipment. Engineers are available from 8:30 AM to 6:00 PM, Eastern Standard Time. Phone 1-800-999-2809.

Service can be obtained from our factory service department. No merchandise may be returned for repair without prior written authorization. Please contact our factory service department at 1-800-999-2809 for a RA number. Only merchandise specified in the return authorization form can be returned to obtain warranty or non-warranty repair. When shipping your unit, pack your system well using the original shipping carton or a similar container and filler material to prevent damage in transit. Send the unit fully insured and prepaid via UPS or other responsible carrier.

Page 2

Contents

INTRODUCTION ......................................................................................................................................................4

Safety Instructions ........................................................................................................................................5

QUICK START ..........................................................................................................................................................6

PANEL DESCRIPTIONS........................................................................................................................................7-9

Front Panel ..................................................................................................................................................7

Rear Panel....................................................................................................................................................8

Helpful Hints ................................................................................................................................................9

INSTALLATION ..................................................................................................................................................10-11

OPERATION ......................................................................................................................................................12-18

Troubleshooting Gain Structure..................................................................................................................13

Recommended Input Wiring Methods ........................................................................................................14

Fine Tuning ................................................................................................................................................15

Compressor/Limiter ....................................................................................................................................16

Special Features Activation ........................................................................................................................17

Jumper Options ..........................................................................................................................................18

TROUBLESHOOTING TIPS ..................................................................................................................................19

GLOSSARY ............................................................................................................................................................20

TECHNICAL INFORMATION ............................................................................................................................21-22

Specifications..............................................................................................................................................21

Block Diagram ............................................................................................................................................22

Page 3

Introduction

CAM8PRO

Page 4

This manual covers installation of the CAM8PRO. It was manufactured to ensure the highest quality audio signal production and control, while still incorporating simple-to-use features.

This manual is designed to familiarize you with the features of your new Bogen CAM8PRO mixer and to guide you through its installation and operation.

Bogenʼs CAM8PRO mixer is electrical equipment, so take all the precautions usually taken when installing and using electrical equipment (see inside front cover). To protect both the users and the equipment, pay particular attention to:

• Grounding - Make sure both the mixer and the devices connected to it are properly grounded.

• Power Supply - Use only the power supply provided or one that meets the manufacturerʼs specifications.

• Cords and Cables - Route all cords and cables so that they will not be tripping hazards or subject to damage (from being

run over or pinched) that could cause them to become shock hazards. Pay particular attention to cords at plugs, convenience receptacles, and the point where they enter the mixer.

Safety Instructions

Page 5

Quick Start

1. Unpack and Connect (See page 10 for more details).

A. Check mixer for shipping damage.

Rack Mounting: To mount the CAM8PRO to a 19” rack, lift the unit up to the front

of the rack and secure it to the front of the rack with the necessary screws (not included with this unit).

B. If special features (see page 17) are to be used, they must be set before the

mixer is mounted.

C. Turn off both mixer and amplifier and turn all volume controls to zero.

D. Connect inputs and set the input pad switch for each channel at the appropriate

level (either MIC or line). Make sure that the bus selector is set for Main Out.

E. Connect output(s) and set the main output pad switch at the appropriate level

(either MIC or line). (Auxiliary output is line-level only.)

2. Power and Set Up (See pages 10-14 for details.)

A. Connect mixer AC power supply.

B. Turn volume controls down, then power up mixer and amplifier.

Note: Mixer will produce signal transients on power up and power down. Always turn the mixer on first before turning on the amplifier and always turn the amplifier off first before turning off the mixer.

C. Adjust Main/AUX out controls to the 2 oʼclock position. Then turn amp up to

normal level while performing audio test.

D. Adjust input gain/trim control for each channel to get a meter reading within the

green area.

E. Adjust individual channel volume controls to the 2 oʼclock position.

3. Fine Tuning (See page 15 for details).

A. In the event of excessive bass, press Low Cut filter switch(es) “on.”

B. If condenser mics are used, press phantom power switch “on” (turns phantom

power on for all inputs set to MIC position).

C. In the event of occasional excessive output level, press Compressor/Limiter

switch “on”.

Page 6

CAM8PRO Front Panel

1. Main/Auxiliary Bus Selector (one per channel)

A 4-position switch which selects destination of channel input. Input can be routed to: a) the main bus (M-up, A-down); b) the auxiliary bus (M-down, A-up-shown at right); c) both the main and auxiliary buses (both up); or d) neither bus (both down).

2. Channel Volume Control Knob (one per channel)

Controls the volume of the channel input to any and all outputs simultaneously.

3. Low Cut Switch

Helps eliminate low frequency noise (100 Hz 18 dB/octave).

4. Main Output Compressor/Limiter Switch and LED

Note: Works only on main bus. Reduces distortion of the main output (due to clipping) by

controlling its dynamic range. When the LED (red) is lit, the Compressor/Limiter is on. The brighter the LED, the more the signal is being compressed.

5. Main Output Volume Control Knob

Controls the output signal volume of the main bus.

6. LED Bar Graph Output Meter

Displays output signal level in decibels, ranging from -18 (green) to +12 (red) VU. 0 VU = +4 dBm. This meter can be set to indicate the signal level of either the main or auxiliary bus and to indicate either the average or peak signal. (See page 18 for details.)

7. Threshold Control

Screw-pot adjustment sets the signal level (-20 to +20 VU; factory setting is 0 VU) at which the Compressor/Limiter becomes active.

8. Ratio Control

Screw-pot adjustment sets the amount of compression (0-100%; factory setting is 100%) of the signal above the threshold.

9. Auxiliary Output Volume Control Knob

Controls the output signal volume of the auxiliary bus output and to the headphones. (There is no connection between this bus and the Compressor/Limiter.)

10. Headphone Jack

A 1/4 inch-diameter TRS mono-only jack for the connection of headphones. (Only monitors AUX bus.)

11. Power Indicator LED

LED displays mixerʼs powered state. Lit when power is on. Not lit when power is off.

12. Power Switch Button

Push button to turn unit on (“in” position); push again to turn unit off (“out” position).

Page 7

M A Bus

Front Panel Descriptions

M.A BUS

M.A

Low

Cut

BUS

3 4

M.A

Low

Cut BUS

Low

Cut

5 7 8 9

AUX

CAM8PRO

Headphone

10 11

Power

Ratio

Threshold

M.A BUS

M.A

Low

BUSCut

M.A

Low

BUS

Cut

M.A

Low

Cut

BUS

M.A

Low

BUS

Cut

On Off

Low

Limit

Cut

MAIN

-12-18 -6 -3

0 100

0 +3 +12+6

CAM8PRO Rear Panel

1. Ground Connection on Rear Panel

Access to ground.

2. AC Power Jack

Mixer power supply input. Accepts a 4-pin DIN connection from a 17V CT 1.5 Amp transformer.

3. Phantom Power Switch

When activated, supplies 30V DC power to all inputs set to MIC level.

4. Auxiliary Bus Output

Balanced, line-level, connection to auxiliary output bus.

5. Main Output Microphone/Line Switch

Selects main output to be either MIC (-50 dBμ) or line (0 dBμ) level.

6. Main Bus Output

Balanced connection to main output bus.

7. Auxiliary Input

Balanced, buffered, uncontrolled, line-level terminals for additional (ninth) input connection directly to the summing buses selected by internal jumpers. The factory default is both jumpers installed. (See page 18 for details.)

8. Input Gain/Trim Control Screw

Adjusts gain of input stage, over a range of 40 dB.

9. Input Pad Microphone/Line Switch

Selects either MIC (-50 dBμ) or line (0 dBμ) level for corresponding input connection.

10. Input

Balanced input connection (pluggable terminal strip).

Page 8

Rear Panel Descriptions

No connect

Center

-50dB

MAIN

0dB

Ground

17VCT

Power

AUX OUT AUX IN

On Off

+-+-+-

Phantom

+-G

3 5

7 8

Trim

Line

--G--+++

+++++----G

Mic

Trim

Line

Mic

Trim

++++----

G++++----G

Line

Mic

9 10

Trim

Line Mic

Line

++++----

G++++----G

Mic

TrimTrim

Line Mic

Trim

Line

++++---

-G++++----G Mic

Trim

Line

++++---

-G++++G----

Mic

+ 16 hidden pages