Bogen ACD2X2 User Manual

Self-Amplified Drop-In Ceiling Speaker

ACD2X2, ACD2X2U

with Back Can and Recessed Volume Control

CEILING GRID

SUPPORT RAIL

CROSSBAR INCLUDED

(2 ft. X 4ft. CEILING GRID ONLY)

CEILING TILE

(CUT IN HALF, OR NO MORE

THAN 23-3⁄4")

ACD2X2

2 ft. X 2ft.

TILE SPACE

2 ft. X 4ft.

TILE SPACE

Bogen’s ACD2X2 Drop-In Ceiling Speaker is a full-range speaker that allows for fast and easy installation, which saves installation time, effort, and cost.

The ACD2X2 is a 2' x 2' speaker that fits perfectly into place in 2' x 2' ceiling grids – without needing to cut ceiling tiles or requiring the use of tile support rails. The ACD2X2 can also be easily installed in 2' x 4' ceiling grids – just make one cut to the ceiling tile, position the support rail (included), and drop the speaker into place.

• Finely perforated grille over the entire front of speaker

• Fully enclosed, industrial grade steel construction

• Enclosed Back Can

• Self-contained 1-watt amplifier

• 8'' main cone with secondary high-frequency cone

• Available in off-white and bright white (“U” versions)

grille finish

• Recessed Volume Control (front-mounted)

• Complies with Requirements of UL-2043

• Support Rail Crossbar (included)

• Seismic attachment points

Frequency Response . . . . . . . . . . 95 Hz - 12 kHz

Max. SPL @ 1W / 1m . . . . . . . . . . 94 dB

Dispersion @ 2 kHz

(6 dB down) . . . . . . . . . . . . . . . . . .100°

Cone Material & Surround . . . . . . Treated paper

Cones . . . . . . . . . . . . . . . . . . . . . . .

8" main cone with secondary

high frequency cone

Maximum Amplifier Output . . . . . .1W

Typical Operational Current . . . . .1 CU (50 mA)

Input Impedance . . . . . . . . . . . . . .2000 ohms

Typical Input Sensitivity . . . . . . . . .125 mV rms

Supply Voltage . . . . . . . . . . . . . . . .24V DC

Magnet Weight . . . . . . . . . . . . . . . .10 oz.

Connection . . . . . . . . . . . . . . . . . . .Via wire nuts

(included in electrical box)

Dimensions . . . . . . . . . . . . . . . . . .23 -7/8" W x 5" H x 23 -7/8" D

Product Weight . . . . . . . . . . . . . . .12 lb.

Plenum-rated, complies with requirements of standard UL-2043.

The speaker shall be a Bogen Model ACD2X2 Drop-In Self-Amplified Ceiling Speaker, which shall be fully enclosed and constructed of industrial grade steel. It shall be comprised of a damped high-compliance factory-mounted loudspeaker that shall consist of an 8" treated paper main cone, a secondary high frequency cone, and a 10-ounce magnet. The unit shall have a 1-watt amplifier. The typical current consumption shall be 1 CU (50 mA). Frequency response shall be 95 Hz - 12 kHz. Input sensitivity shall be 125 mV rms with max. SPL @ 94 dB (1M). Input impedance shall be 2k ohms. Dispersion shall be 100°. The speaker shall have a non-reflective, off-white or bright white (“U” version) finish metal grille with a recessed volume control accessible through front grille. It shall include 4 seismic attachment points.

The speaker assembly will fit into 2' x 2' and 2' x 4' ceiling grids. For 2' x 2' installations, support rails shall not be required and no cuts to the ceiling shall be necessary. For 2' x 4' installations, a single cut to the ceiling tile and an included support rail shall be required. The speaker shall measure 23-7/8" W x 5" H x 23-7/8" D and shall weigh 12 lb.

SPECIFICATIONS

Architect and Engineer Specifications

50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel: 201-934-8500 Fax: 201-934-9832 www.bogen.com

Specifications subject to change without notice.

Part No. 54-9273-01D 0902

Self-Amplified Drop-In Ceiling Speaker: ACD2X2 & ACD2X2U

ACD2X2

ACD2X2U

Model

Off-white Finish

Bright White Finish (U)

Back Can

Recessed Volume

Control

●

●●●

●

SEISMIC

ATTACHMENT

POINTS (4X)