BOE HV550WU2-202 Specification

Page 1
PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF BOE DT AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE DT AND MUST BE RETURNED TO BOE DT UPON ITS REQUEST
TITLE:
HV550WU2-202 Preliminary Product Specification
SPEC. NUMBER
B2010-8002-O (1/3)
BEIJING BOE DISPLAY TECHNOLOGY
PRODUCT GROUP
TFT LCD
REV.
0
ISSUE DATE
2013.05.03
PAGE
of 25
1
A4(210 X 297)
A4(210 X 297)
Page 2
PRODUCT GROUP
REVISION HISTORY
REV ISSUE DATE
TFT LCD
0 2013.05.03
REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED
0 - Initial Release 2013.05.03
SPEC. NUMBER
B2010-8002-O (2/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
2
A4(210 X 297)
Page 3
PRODUCT GROUP
3.1 TFT LCD Modul
g
REV ISSUE DATE
TFT LCD
0 2013.05.03
Contents
No ITEM Page
REVISIONS HISTORY 2 CONTENTS
1 GENERAL DESCRIPTION
1.1 Introduction
1.2 Features
1.3 Applications
1.4 General Specification 2 ABSOLUTE MAXIMUM RATINGS 6 3 ELECTRICAL SPECIFICATIONS 7
e
4 INTERFACE CONNECTION 8
3 4
4.1 Module Input Signal & Power
4.2 LVDS Interface 5 SIGNAL TIMING SPECIFICATIONS
5.1 Timing Parameters
5.2 Signal Timing Waveform
5.3 Input Signals, Basic Display Colors & Cray Scale Of Colors
5.4 Power Sequence 6 OPTICAL SPECIFICATIONS 15 7 MECHANICAL CHARACTERISTICS 18 8 RELIABLITY 29 9 PRODUCT SERIAL NUMBER 20
10 PACKING INFORMATION 21 11 HANDING & CAUTIONS 23 12 APPENDIX
11
24
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
3
A4(210 X 297)
Page 4
PRODUCT GROUP
G1
Block
z
LVDS interf
ith 2 pixel / clock
ADS
REV ISSUE DATE
TFT LCD
0 2013.05.03
1.0 GENERAL DESCRIPTION
1.1 Introduction
HV550WU2-202 is a color active matrix TFT LCD open cell using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 54.6inch diagonally measured active area with WUXGA resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.
RGB(Mini-LVDS)
VDD
+12.0V
LVDS
2Ports
LVDS_SEL
# 7
CN1
(51pin)
S1 S1920
Gate Driver Circuit
Timing Controller
[LVDS Rx & Mini-LVDS
Tx integrated]
Source Driver Circuit
TFT - LCD Panel
(1920 × RGB × 1080 pixels)
Power Circuit
G1080
1.2 Features
ace w
z High-speed response z Low color shift image quality z 8-bit color depth, display 16.7M colors z High luminance and contrast ratio, low reflection and wide viewing angle z DE (Data Enable) only mode z z RoHS compliant
SPEC. NUMBER
technology is applied for high display quality
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
4
B2010-8002-O (3/3)
A4(210 X 297)
Page 5
PRODUCT GROUP
Display colors
16.7M(8bits
true)
colors
REV ISSUE DATE
TFT LCD
1.3 Application
z Home Alone Multimedia TFT-LCD TV z Display Terminals for Control System z Full High Definition TV(FHD TV) z AV application Products
1.4 General Specification
< Table 1. General Specifications >
Parameter Specification Unit Remark
Active area
1209.6(H) × 680.4(V)
0 2013.05.03
mm Array
Number of pixels
Pixel pitch
Pixel arrangement Pixels RGB Vertical stripe Array
Display mode Transmission mode, Normally Black
Open Cell
Transmittance
Power Consumption 9.0W(typ.)
Surface Treatment Haze 1%, 2H, Anti-glare treatment (FPR)
Haze 0%, 2H, (Front Polarizer)
1920(H) ×1080(V)
630(H) ×630(V)
-
6.5 (typ.) %
pixels
Array
At center point with BOE BLU
Watt
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
5
A4(210 X 297)
Page 6
PRODUCT GROUP
Parameter
Symbol
Min
Max
Unit
Remark
Wet bulb temperature should be 39
max. and no condensation of water
Wet Bulb
R
REV ISSUE DATE
TFT LCD
0 2013.05.03
2.0 ABSOLUTE MAXIMUM RA TINGS
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. LCD Open Cell Electrical Specifications >
Power Supply Voltage
LCD Module
VDD VSS-0.3 13.5 V
T
Operating Temperature
T
Storage Temperature T
Operating Ambient Humidity
Hop 10 80 %RH
OP
SUR
ST
.
.
0+50
0+60
-20 +60
[VSS=GND=0V]
Ta = 25
Note 1
Storage Humidity Hst 10 80 %RH
Note 1 : Temperature and relative humidity range are shown in the figure below.
Temperature [C]
10
0
10 20 30 40 50 60 70 800-20
Dry Bulb Temperature [
20
30
40
°C]
50
80%
60
60%
H]
40%
Humidity [(%)
10%
.
Storage
Operation
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
6
A4(210 X 297)
Page 7
PRODUCT GROUP
LVDS
VIL0-
0.6
V
REV ISSUE DATE
TFT LCD
0 2013.05.03
3.0 ELECTRICAL SPECIFICATIONS
3.1 TFT LCD Open Cell
< Table 3. LCD Open Cell Electrical Specifications >
Values
Parameter Symbol
Min Typ Max
Power Supply Input Voltage VDD 10.8 12 13.2 Vdc Power Supply Ripple Voltage VRP 300 mV
Power Supply Current IDD 700 mA Power Consumption PDD 9.0 Watt Rush current IRUSH 4 A Note 2
Differential Input High
VLVTH +100 +300 mV
Threshold Voltage
Interface
Differential Input Low Threshold Voltage
VLVTL -300 -100 mV
[Ta =25±2 ℃]
Unit Remark
Note 1
Common Input Voltage VLVC 1.0 1.2 1.4 V
Input High Threshold
VIH 2.7 - 3.3 V
CMOS Interface
Voltage Input Low Threshold Voltage
Note 1 : The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=12.0V, Frame rate f Test Pattern of power supply current
a) Typ : Color Test (L0/L255) b) Max : Vertical Subline (L0/L255)
Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min)
=60Hz and Clock frequency = 75.4MHz.
V
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
7
A4(210 X 297)
Page 8
PRODUCT GROUP
3
SCL
I2C Clock
28
CH2[0]
Second pixel negative LVDS
3
CH1[0]
38
CH2[3]
13
CH1[0]
diff
0
38
CH2[3]
18
GND
43
NC
p
p
REV ISSUE DATE
TFT LCD
0 2013.05.03
4.0 INTERF ACE CONNECTION
4.1 Open Cell Input Signal & Power
- Connector : FW05010-51(Manufactured by FOOSUNG) or Equivalent. < Table 5. Open Cell Input Connector Pin Configuration >
Pin No
1 NC No Connection 26 2D/3D 2D/3D Signal Select 2SDA I
4 WP nWR(PGAMA data write protect) 29 CH2[0]+
5 NC 30 CH2[1]- “ 6 NC 31 CH2[1]+
7 SELLVDS
8 NC 33 CH2[2]+
9NC 34GND 10 NC 35 CH2CLK- First pixel negative LVDS clock 11 GND 36 CH2CLK+ First pixel positive LVDS clock
12 CH1[0]-
1
14 CH1[1]- 39 CH2[3]+
15 CH1[1]+ 40 CH2[4]-/NC
16 CH1[2]- 41 CH2[4]+/NC
17 CH1[2]+ 42 NC
Symbol Description
2
C Data 27 L/R Left Right Eye Frame Sync.
High or Openh: NS
Low: JEIDA
First pixel negative LVDS
differential data input. Pair0
+
First pixel positive LVDS
erential data input. Pair
Pin No
32 CH2[2]-
37 GND
Symbol Description
-
-“
differential data input. Pair0 Second pixel positive LVDS
differential data input. Pair0
Second pixel negative LVDS
differential data input. Pair0 Second pixel positive LVDS
differential data input. Pair0
19 CH1CLK- First pixel negative LVDS clock 44 GND Ground 20 CH1CLK+ First pixel positive LVDS clock 45 GND “ 21 GND 46 GND
22 CH1[3]- 47 NC “ 23 CH1[3]+ 48 VCC Input Voltage
24 CH1[4]-/NC
25 CH1[4]+/NC
SPEC. NUMBER
B2010-8002-O (3/3)
First pixel negative LVDS
differential data in
First pixel positive LVDS
differential data input. Pair0
ut. Pair0
49 VCC
50 VCC
51 VCC
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
8
A4(210 X 297)
Page 9
PRODUCT GROUP
R
LCM
BIST Patt
REV ISSUE DATE
TFT LCD
4.0 INTERF ACE CONNECTION
4.1 Open Cell Input Signal & Power
Notes : 1. NC(Not Connected) : This pins are only used for BOE internal operations.
2. Input Level of LVDS signal is based on the IEA 664 Standard.
3. LVDS_SEL : This pin is used for selecting LVDS signal data format. If this Pin : High (3.3V) or Open (NC) Æ Normal NS LVDS format Otherwise : Low (GND) Æ JEIDA LVDS format
ear view of
1
(FW05010-51(FOOSUNG))
51
ern
0 2013.05.03
B2010-8002-O (3/3)
SPEC. NUMBER
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
9
A4(210 X 297)
Page 10
PRODUCT GROUP
LVDS R
(LVDS R
LVDS Dat
Bit-1G2G4
REV ISSUE DATE
4.2 LVDS Interface
-
Channel No. Data No.
eceiver : Timing Controller
< Table 6. Open Cell Input Connector Pin Configuration >
0
1
2
3
TFT LCD
x merged) /
8-bit LVDS Type
NS JEIDA
Bit-0 R0 R2
Bit-1 R1 R3
Bit-2 R2 R4
Bit-3 R3 R5
Bit-4 R4 R6
Bit-5 R5 R7
Bit-6 G0 G2
Bit-0 G1 G3
Bit-2 G3 G5
Bit-3 G4 G6
Bit-4 G5 G7
Bit-5 B0 B2
Bit-6 B1 B3
Bit-0 B2 B4
Bit-1 B3 B5
Bit-2 B4 B6
Bit-3 B5 B7
Bit-4 HS HS
Bit-5 VS VS
Bit-6 DE DE
Bit-0 R6 R0
Bit-1 R7 R1
Bit-2 G6 G0
Bit-3 G7 G1
Bit-4 B6 B0
Bit-5 B7 B1
Bit-6 -
0 2013.05.03
a : Pixel Data
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
10
A4(210 X 297)
Page 11
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
5.0 SIGNAL TIMING SPECIFICATION
5.1 Timing Parameters (DE only mode)
< Table 8. Timing Table >
Item Symbols Min Typ Max Unit
Frequency 1/Tc 66.00 74.25 82 MHz
Clock
Frame Period Tv
High Time Tch - 4/7Tc -
Low Time Tcl - 4/7Tc -
0 2013.05.03
1116 1126 1150 lines
56.32 60 62.77 Hz
Vertical Display Period Tvd - 1080 - lines
One line Scanning Period Th 1050 1100 1150 clocks
Horizontal Display Period Thd 960 960 960 clocks
Notes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal operation.
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
11
A4(210 X 297)
Page 12
PRODUCT GROUP
DE(Data Enable)
DE(Data Enable)
REV ISSUE DATE
5.2 Signal Timing Waveform
DCLK
tCLK
First data
Second data
0.5 VDD
Invalid data
Invalid data
TFT LCD
Valid data
Pixel data
Pixel data
Pixel data
Valid data
Pixel data
0 2013.05.03
Invalid data
Invalid data
HSync
DE(Data Enable)
VSync
SPEC. NUMBER
tHP
tHV
tVP
tVV
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
12
B2010-8002-O (3/3)
A4(210 X 297)
Page 13
PRODUCT GROUP
000000001111111100000000Green
G
↑↑↑
↓↓↓
REV ISSUE DATE
TFT LCD
0 2013.05.03
5.3 Input Signals, Basic Display Colors and Gray Scale of Colors
< Table 9. Input Signal and Display Color Table >
Color & Gray Scale
Basic Colors
ray Scale
of Red
Gray Scale of Green
Gray Scale of Blue
Gray Scale of White
△ ▽
△ ▽
△ ▽
Input Data Signal
B6 B5 B4 B3 B2 B1 B0G5 G4 G3 G2 G1 G0G6R3R4R5R6 R0R2 R1 B7G7R7
000000000000000000000 000Black
Blue DataGreen DataRed Data
000000000000000000000000Black 111111110000000000000000Blue
11111111111111100000000Cyan
1 000000000000000011111111Red 111111110000000011111111Magenta 000000001111111111111111Yellow 111111111111111111111111White 000000000000000000000000Black 000000000000000010000000 000000000000000001000000Darker
↑ ↓
000000000000000010111111Brighter 000000000000000001111111 000000000000000011111111Red 000000000000000000000000Black 000000001000000000000000 000000000100000000000000Darker
000000001011111100000000Brighter 000000000111111100000000 000000001111111100000000Green 000000000000000000000000Black 100000000000000000000000 010000000000000000000000Darker
↑ ↓
101111110000000000000000Brighter 011111110000000000000000 111111110000000000000000Blue
100000001000000010000000 010000000100000001000000Darker
101111111011111110111111Brighter 01111110111111101111111
1
111111111111111111111White
111
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
13
A4(210 X 297)
Page 14
PRODUCT GROUP
Interf
l
Acti
V
REV ISSUE DATE
5.4 Power Sequence
12V
0.9VDD
Power Supply
VDD
aceSigna
(InputData)
Power Supply
VBL
Dimming Signal
VDIM/PDIM
0.1VDD
0V
T1
Hi-Z
24V
0V
0V
T2
0.9VBL
0.1VBL
T4
TFT LCD
T3
T7
T5
T6
veSignal
0.8VBL(typ)
Valid
0.9VBL
T8
T10
T9
0 2013.05.03
0.9VDD
0.1VDD
T11
Hi-Z
T12
BLU ON/OFF enable
( VON/OFF )
0V
< Table 10. Sequence Table >
Parameter
Min Typ Max
alues
Units
T1 0.5 - 10 ms T2 0 - 50 ms T3 200 - - ms T4 20 - - ms T5 500 - - ms T6 0 - - ms T7 - - 10 ms T8 0 - - ms
T9 500 - - ms T10 200 - - ms T11 0 - 50 ms T12 1--s
Notes: 1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
2 .Even though T4 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
3. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
14
A4(210 X 297)
Page 15
PRODUCT GROUP
Viewi
Horizontal
Wy0.290
Bl
x
REV ISSUE DATE
TFT LCD
0 2013.05.03
6.0 OPTICAL SPECIFICATIONS
The test of optical specifications shall be measured in a dark room (ambient luminance1 lux and temperature=25±2) with the equipment of Luminance meter system (Goniometer system and PR730) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θ o’clock direction (the “right”), θ ) as the 9 o’clock direction (“left”) and θ
(= θ12) as the 12 o’clock direction (“upward”), θ
Ø=90
(= θ6 ) as the 6 o’clock direction (“bottom”). While
Ø=270
scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be
12.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock. < Table 11. Optical Table >
[VDD = 12.0V, Frame rate = 60Hz, Ta =25±2 ℃]
Parameter Symbol Condition Min Typ Max Unit Remark
ng
Angle
Vertical
Θ
Θ
Θ
Θ
12
3
9
6
CR > 10 Note 1
89 Deg.
89 Deg.
89 Deg.
89 Deg.
Contrast ratio CR 1200:1 1400:1 - Note 2
(=θ3) as the 3
Ø=0
Ø=180
(= θ
9
Reproduction
of color
White
Red
Green
W
R
R
G
G
B
x
x
y
x
y
Θ = 0°
(Center)
Normal
Viewing
Angle
TYP.
-0.03
0.280
0.630
0.345
0.305
0.628
0.150
TYP. + 0.03
ue
Response Time G to G T
B
y
g
-810msNote 4
0.060
Gamma Scale 2.0 2.2 2.4
Cell Transmittance 6.5 % Note 5
SPEC. NUMBER
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
Note 3
PAGE
of 25
15
B2010-8002-O (3/3)
A4(210 X 297)
Page 16
PRODUCT GROUP
is defined
p
pg
Lumi
LCD Modul
REV ISSUE DATE
TFT LCD
0 2013.05.03
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface.
2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See Figure 1 shown in Appendix) Luminance Contrast Ratio (CR)
mathematically.
CR =
3. The color chromaticity coordinates specified in Table 11. shall be calculated from the spectral data measured with all made at the center of the panel.
4. Response time Tg is the average time required for display transition by switching the input signal as below table and is based on Frame rate fV =60Hz to optimize. Each time in below table is defined as Figure 3 and shall be measured by switching the
5. Definition of Transmittance (T%) :
Module is with white(L255) signal input
Transmittance =
Luminance when displaying a white raster Luminance when displaying a black raster
ixels first in red, green, blue and white. Measurements shall be
nance of
Luminance of BLU
e
× 100 %
B2010-8002-O (3/3)
SPEC. NUMBER
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
16
A4(210 X 297)
Page 17
PRODUCT GROUP
g
g
REV ISSUE DATE
TFT LCD
0 2013.05.03
7.0 MECHANICAL CHARACTERISTICS
7.1 Dimensional Requirements
Figure 4 (located in Appendix) shows mechanical outlines for the model HV550WU2-202. Other parameters are shown in Table 12.
< Table 12. Dimensional Parameters >
Parameter Specification Unit
Active area
Pixel pitch
Number of pixels
1209.6 (H) ×680.4(V)
0.63(H) ×0.63(V)
1920(H) ×1080(V) (1 pixel = R + G + B dots)
mm
mm
pixels
7.2 Mountin
See Figure 5. (Shown in Appendix)
7.3 Semi-Glare and Polarizer Hardness
The surface of the LCD has an Anti-glare coating to minimize reflection and a coating to Reduce scratching.
SPEC. NUMBER
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
17
B2010-8002-O (3/3)
A4(210 X 297)
Page 18
PRODUCT GROUP
g
gp p
,
±
X
±
Y
±
Z Once for each direction
REV ISSUE DATE
TFT LCD
8.0 RELIABILITY TEST
The Reliability test items and its conditions are shown in below.
< Table 13. Reliability Test Parameters >
No Test Items Conditions
1 High temperature storage test
2 Low temperature storage test
3 High temperature & high
humidity operation test
4Hi
5 Low temperature operation test
h temperature operation test
Ta = 60 , 240 hrs
Ta = -20 , 240 hrs
Ta = 50 , 80%RH, 240hrs
Ta = 50 , 240hrs
Ta = 0 , 240hrs
0 2013.05.03
6 Thermal shock
7 Vibration test
(non-operating)
8 Shock test
(non-operating)
9 Electro-static discharge test
Ta = -20 60 (0.5 hr), 100 cycle
Frequency : 10 ~ 300 Hz, Random
Gravity / AMP : 1.0 Grms
Period : X, Y, Z 30 min/axis
Gravity : 50G
Pulse width : 11msec, Sine wave
,
,
Air : ±15kV ,150pF/330Ω ,100Point ,1time/Point Contact :±8kV ,150pF/330Ω ,100Point ,1time/Point Non operation Contact:±4KV~±6KV,150pF/330Ω,100Point, Input connector Pin, 3 times/pin with no function loss
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
18
A4(210 X 297)
Page 19
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
9.0 PRODCUT SERIAL NUMBER
0 2013.05.03
HV550WU2-202
1 2 3 4 5 6 7
XXXXXXXXXXX XXXXXX
1. Control Number
2. Rank / Grade
3. Line Classification
4. Year (2011 : 11, 2012 : 12, …)
SPEC. NUMBER
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
5. Month (1,2,3, … , 9, X, Y, Z)
6. Internal Use
7. Serial Number
19
PAGE
of 25
B2010-8002-O (3/3)
A4(210 X 297)
Page 20
PRODUCT GROUP
1 Pallet: 7 Box + 1Cover
REV ISSUE DATE
TFT LCD
0 2013.05.03
10.0 PACKING INFORMATION
BOE provides the standard shipping container for customers, unless customer specifies their packing information. The standard packing method and Barcode information are shown in below.
10.1 Packing Order
1 Box: 10 Panel +11 Space +2 desiccant
SPEC. NUMBER
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
20
B2010-8002-O (3/3)
A4(210 X 297)
Page 21
PRODUCT GROUP
l
Si
110
(L)×55
(W)
REV ISSUE DATE
TFT LCD
10.2 Packing Note
y Box Dimension : 1374 mm (L) × 1140mm (W) ×955mm (H) y Package Quantity in one Box : 10pcs
10.3 Box Label
yLabe y Contents
ze :
Model : HV550WU2-202 Q`ty : 10 Open Cell in one box. Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product
mm
mm
0 2013.05.03
00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no
SPEC. NUMBER
HV550WU2-202
0000000000000
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
XXXX
10
XXXX.XX.XX
Internal CODE
RoHS Mark
PAGE
of 25
21
B2010-8002-O (3/3)
A4(210 X 297)
Page 22
PRODUCT GROUP
yp
ith
(4)
() p
REV ISSUE DATE
1 1.0 HANDLING & CAUTIONS
(1) Cautions when taking out the module
y Pick the pouch only, when taking out module from a shipping package.
(2) Cautions for handling the module
y As the electrostatic discharges may break the LCD module, handle the LCD
module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
y As the LCD panel and back - light element are made from fragile glass material,
impulse and pressure to the LCD module should be avoided.
y As the surface of the polarizer is very soft and easily scratched, use a soft dry
cloth without chemicals for cleaning.
y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. yHandle connectors and cables w
(3) Cautions for the operation
y When the module is operating, do not lose CLK, ENAB signals. If any one of
these signals is lost, the LCD panel would be damaged.
y Obey the supply voltage sequence. If wrong sequence is applied, the module
would be damaged.
Cautions for the atmosphere
y Dew drop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or
humidity atmosphere. Storage in an electro-conductive polymer packing pouch
and under relatively low temperature atmosphere is recommended.
(5) Cautions for the module characteristics
y Do not apply fixed pattern data signal to the LCD module at product aging. yApplying fixed pattern for a long time may cause image sticking.
(6) Other cautions
y Do not disassemble and/or re-assemble LCD module. y Do not re-adjust variable resistor or switch etc. yWhen returning the module for repair or etc., Please pack the module not to be
broken. We recommend to use the original shipping packages.
TFT LCD
care.
0 2013.05.03
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
22
A4(210 X 297)
Page 23
PRODUCT GROUP
gy
REV ISSUE DATE
12.0 APPENDIX
TFT LCD
< Figure 1. Measurement Set Up >
0 2013.05.03
PR730
(L = 180cm)
< Figure 2. White Luminance and Uniformity Measurement Locations >
1/9V
1/2V
8/9V
SPEC. NUMBER
1/9H 1/2H 8/9H
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
Active Area Test points
PAGE
23
of 25
B2010-8002-O (3/3)
A4(210 X 297)
Page 24
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
< Figure 3. Response Time Testing >
0 2013.05.03
SPEC. NUMBER
B2010-8002-O (3/3)
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
24
A4(210 X 297)
Page 25
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
< Figure 4. TFT-LCD Open Cell Outline Dimensions (Front View) >
0 2013.05.03
SPEC. NUMBER
B2010-8002-O (3/3)
×
SPEC. TITLE
HV550WU2-202 Preliminary Product Specification
PAGE
of 25
25
A4(210 X 297)
Loading...