THIS SPECIFICATION IS THE PROPERTY OF BOE DT AND SHALL NOT BEG
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE DT
AND MUST BE RETURNED TO BOE DT UPON ITS REQUESTG
TITLE:
HV320WX2-600 Preliminary Product Specification
www.panelook.com
PROPRIETARY NOTE
BEIJING BOE DISPLAY TECHNOLOGY
SPEC. NUMBER PRODUCT GROUP
TFT LCD
B2010-8002-O (1/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
REV.
P0
ISSUE DATE
2012.07.18
PAGE
of 23
1
A4(210 X 297)
A4(210 X 297)
www.panelook.com
Page 2
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
REVISION HISTORY
REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED
P0--Initial Release 20120718 Du Yufan
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (2/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
2
A4(210 X 297)
www.panelook.com
Page 3
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
Contents
NoITEM Page
REVISIONS HISTORY 2
CONTENTS
1 GENERAL DESCRIPTION
1.1 Introduction
1.2 Features
1.3 Application Information for DID (Digital Information Display)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
19
22
PAGE
of 23
3
A4(210 X 297)
www.panelook.com
Page 4
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
1.0 GENERAL DESCRIPTION
1.1 Introduction
HV320WX2-600 is a color active matrix TFT LCD open cell using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This open cell has a 31.51 inch
diagonally measured active area with WXGA resolutions (1366 horizontal by 768 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical stripe and this open cell can display 16.7M colors. The TFT-LCD panel is intended
to support applications to provide an excellent performance for Flat Panel Display, such as
Transparent TV, show Window, Kiosk etc.
RGB(Mini-LVDS)
VDD
+12.0V
LVDS
5pairs
LVDS_SEL
# 9
BIST_
# 27
CN1
(30pin)
Timing Controller
[LVDS Rx & Mini-LVDS
Tx integrated]
S1S1366
Gate Driver Circuit
G1
Source Driver Circuit
TFT - LCD Panel
(1366 Ý RGB Ý 768 pixels)
Power Circuit
Block
G768
1.2 Features
z LVDS interface with 1 pixel / clock
z High-speed response
z Low color shift image quality
z 8-bit color depth, display 16.7M colors
z High luminance and contrast ratio, low reflection and wide viewing angle
z DE (Data Enable) only mode
z AFFS technology is applied for high display quality
z RoHS compliant
1.3 Application Information for DID (Digital Information Display)
A long-term display like DID application may cause uneven display including image retention.
To optimize module’s lifetime and function, several operating usages are required.
1. Normal operating condition
‒ Temperature: 20 · 15ć
‒ Humidity: 55 · 20%
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
4
A4(210 X 297)
www.panelook.com
Page 5
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
‒ Display pattern: moving picture or regular switchover display
Note) Long-term static information image may cause uneven display.
2. Operating usages under abnormal operating condition.
a. Ambient condition
‒ Well-ventilated place is recommended to set up DID system.
b. Power off and screen saver
– Periodical power-off or screen saver is needed after long-term static display.
3. Operating usages to protect uneven display due to long-term static information display
a. Suitable operating time for E-DID: under 20 hours a day
b. Periodical display contents change from static image to moving picture
‒ Liquid crystal refresh time required
c. Periodical background color and character (image) color change.
‒ Use different colors for background and character (image), respectively.
‒ Change colors periodically
d. Avoid combination of background and character with large different luminance.
4. Lifetime in this spec is guaranteed only when DID is used under right operating usages.
1.4 General Specification
< Table 1. General Specifications >
ParameterSpecificationUnitRemark
Active area
Number of pixels
Pixel pitch
Pixel arrangement Pixels RGB Vertical stripe
Display colors 16.7M(8bits-true) colors
Display mode Transmission mode, Normally Black
697.685(H) Ý 392.256(V)
1366(H) ശ768(V)
170.25(H) ശRGBശ510.75(V) ໃ
mm
pixels
Open Cell
Transmittance
Weight 1180 (typ.) gram
Power Consumption 4.0 (typ.) Watt
6.6 (typ.) %
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
At center point
with BOE BLU
PAGE
of 23
5
A4(210 X 297)
www.panelook.com
Page 6
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. Open Cell Electrical Specifications >
ParameterSymbolMin.Max.UnitRemark
Power Supply Voltage VDD VSS-0.3 13.2 V
0 +50
Operating Temperature
T
OP
T
0 +60
SUR
ć
ć
[VSS=GND=0V]
Ta = 25 ć
Storage Temperature T
Operating Ambient
Humidity
-20 +60
ST
ć
Hop 1080 %RH
Storage Humidity Hst 1080 %RH
Note 1 : Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 ć max. and no condensation of water.
Note 1
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
6
A4(210 X 297)
www.panelook.com
Page 7
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
3.0 ELECTRICAL SPECIFICATIONS
3.1 TFT LCD Open Cell
< Table 3. Open Cell Electrical Specifications >
Values
Parameter Symbol
Min Typ Max
Power Supply Input Voltage VDD 10.8 12 13.2 Vdc
Power Supply Ripple Voltage VRP 300mV
Power Supply Current IDD - 333592 mA
Power Consumption PDD 4.0 7.1 Watt
Rush current IRUSH - - 3.0 A Note 2
Differential Input High
VLVTH +100 +300 mV
Threshold Voltage
LVDS
Interface
Differential Input Low
Threshold Voltage
VLVTL -300 -100 mV
[Ta =25ധ2 ć]
Unit Remark
Note 1
Common Input Voltage VLVC 1.0 1.2 1.4 V
Input High Threshold
VIH 2.7 - 3.3 V
CMOS
Interface
Voltage
Input Low Threshold
VIL 0 - 0.6 V
Voltage
Note 1 : The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=12.0V,
Frame rate f
Test Pattern of power supply current
a) Typ : Mosaic 8 x 6 Pattern(L0/L255) b) Max : Skip 1H2V Sub Dot
Pattern(L0/L255)
=60Hz and Clock frequency = 75.4MHz.
V
Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min)
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
7
A4(210 X 297)
www.panelook.com
Page 8
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
4.0 INTERFACE CONNECTION
4.1 Module Input Signal & Power
- Connector : IS100-L30B-C23(Manufactured by UJU) or Equivalent.
< Table 4. Open Cell Input Connector Pin Configuration >
Notes : 1. NC(Not Connected) : This pins are only used for BOE internal operations.
2. Input Level of LVDS signal is based on the IEA 664 Standard.
3. LVDS_SEL : This pin is used for selecting LVDS signal data format.
If this Pin : High (3.3V) or Open (NC) Æ Normal NS LVDS format
Otherwise : Low (GND) Æ JEIDA LVDS format
4. BIST : This pin is used for selecting display pattern mode when input DE or input CLOCK quits toggling.
If this Pin : Low (GND) or Open (NC) Æ Free run mode(Black Pattern)
Otherwise : High( 3.3V) Æ BIST mode(BIST Pattern)
Sequence : On = VDD ≥LVDS Option , BIST Option ≥Interface signalOff = Interface signal ≥ LVDS Option , BIST Option ≥ VDD
Rear view of LCM
BIST Pattern
‘L’ or NC=Free run mode ,
‘H’= BIST mode
1
IS100-L30B-C23 (UJU)
30
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
8
A4(210 X 297)
www.panelook.com
Page 9
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
4.2 LVDS Interface
- LVDS Receiver : Timing Controller (LVDS Rx merged) / LVDS Data : Pixel Data
< Table 5. Open Cell Input Connector Pin Configuration >
LVDS Pin Vesa Data format JEIDA Data format Remark
TxIN/RxOUT0 Red0 [LSB] R2
TxIN/RxOUT1 Red1 R3
TxIN/RxOUT2 Red2 R4
TxOUT/RxIN0
TxIN/RxOUT3 Red3 R5
TxIN/RxOUT4 Red4 R6
TxIN/RxOUT6 Red5 R7 [MSB]
TxIN/RxOUT7 Green0 [LSB] G2
TxIN/RxOUT8 Green1 G3
TxOUT/RxIN1
TxOUT/RxIN2
TxIN/RxOUT9 Green2 G4
TxIN/RxOUT12 Green3 G5
TxIN/RxOUT13 Green4 G6
TxIN/RxOUT14 Green5 G7 [MSB]
TxIN/RxOUT15 Blue0 [LSB] B2
TxIN/RxOUT18 Blue1 B3
TxIN/RxOUT19 Blue2 B4
TxIN/RxOUT20 Blue3 B5
TxIN/RxOUT21 Blue4 B6
TxIN/RxOUT22 Blue5 B7 [MSB]
TxIN/RxOUT24 HSYNC HSYNC
TxIN/RxOUT25 VSYNC VSYNC
TxIN/RxOUT26 DEN DEN
TxIN/RxOUT27 Red6 R0 [LSB]
TxIN/RxOUT5 Red7 [MSB] R1
TxIN/RxOUT10 Green6 G0 [LSB]
TxOUT/RxIN3
TxIN/RxOUT11 Green7 [MSB] G1
TxIN/RxOUT16 Blue6 B0 [LSB]
TxIN/RxOUT17 Blue7 [MSB] B1
TxIN/RxOUT23 Reserved Reserved
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
9
A4(210 X 297)
www.panelook.com
Page 10
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
5.0 SIGNAL TIMING SPECIFICATION
5.1 Timing Parameters (DE only mode)
< Table 6. Timing Table >
ITEM Symbol Min Typ Max Unit Note
Period t
CLK
Frequency - 56 75.4 85.0 MHz
Period t
Hsync
Frequency f
11.8 13.3 17.9 ns
CLK
HP
H
REV ISSUE DATE
P0 2012.07.18
145015602000 t
CLK
39.4 48.4 55 KHz
Period tVP 7788061200 t
HP
Vsync
Frequency fV 476065Hz
Horizontal
Valid t
HV
- 1366 - t
CLK
Active
Display Term
Vertical Active
Tot alt
Valid t
HP
VV
145015602000 t
- 768 - t
CLK
HP
Display Term
Notes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal
operation.
Tot alt
VP
778 8061200 t
HP
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
10
A4(210 X 297)
www.panelook.com
Page 11
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
5.2 Signal Timing Waveform
tCLK
DCLK
First data
Second data
0.5 VDD
Invalid data
Invalid data
TFT LCD
Valid data
Pixel data
Pixel data
Pixel data
Valid data
Pixel data
REV ISSUE DATE
P0 2012.07.18
Invalid data
Invalid data
DE(Data Enable)
HSync
DE(Data Enable)
VSync
tHP
tHV
tVP
tVV
DE(Data Enable)
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
11
A4(210 X 297)
www.panelook.com
Page 12
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
5.3 Input Signals, Basic Display Colors and Gray Scale of Colors
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
12
A4(210 X 297)
www.panelook.com
Page 13
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
5.4 Power Sequence
To prevent a latch-up or DC operation of the Open Cell, the power on/off sequence shall
be as shown in below
< Table 8. Sequence Table >
Parameter
T10.5 - 20ms
T20 - 50ms
T3200- - ms
T4200- - ms
T50 - 50ms
T61 - - s
Notes: 1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
2. Back Light must be turn on after power for logic and interface signal are valid.
Min Typ Max
Values
Units
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
13
A4(210 X 297)
www.panelook.com
Page 14
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
6.0 OPTICAL SPECIFICATIONS
The test of optical specifications shall be measured in a dark room (ambient luminanced1 lux
and temperature=25r2ć) with the equipment of Luminance meter system (Goniometer
system and PR730) and test unit shall be located at an approximate distance 50cm from the
LCD surface at a viewing angle of θ and Φ equal to 0q. We refer to θ
o’clock direction (the “right”), θ
) as the 9 o’clock direction (“left”) and θ
(= θ12) as the 12 o’clock direction (“upward”), θ
Ø=90
(= θ6) as the 6 o’clock direction (“bottom”). While
Ø=270
scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay
fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be
12.0V +/-10% at 25qC. Optimum viewing angle direction is 6 ’clock.
< Table 9. Optical Table >
[VDD = 12.0V, Frame rate = 60Hz, Ta =25·2 ć]
(=θ3 ) as the 3
Ø=0
Ø=180
(= θ
9
Parameter Symbol Condition Min Typ Max Unit Remark
Θ
3
89Deg.
Horizontal
Viewing
Angle
Θ
Θ
12
9
89Deg.
CR > 10
89Deg.
Vertical
Θ
Contrast ratio CR
6
900:1 1200:1 - Note 2
89Deg.
Θ = 0q
Color Gamut
-
(Center)
72% Note 3
Normal
Response Time G to G T
Gamma Scale 2.0 2.2 2.4
g
Viewing
Angle
- 8 10ms Note 4
With BOE
Module
Cell Transmittance6.6 % Note 5
Note 1
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
14
A4(210 X 297)
www.panelook.com
Page 15
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
direction with respect to the optical axis which is normal to the LCD surface.
2. Contrast measurements shall be made at viewing angle of T= 0q and at the center of the LCD
surface. Luminance shall be measured with all pixels in the view field set first to white, then
to the dark (black) state. (See Figure 1 shown in Appendix) Luminance Contrast Ratio (CR)
is defined mathematically.
Luminance when displaying a white raster
CR =
Luminance when displaying a black raster
3. The color chromaticity coordinates specified in Table 9.shall be calculated from the spectral
data measured with all pixels first in red, green, blue and white. Measurements shall be
made at the center of the panel.
4. Response time Tg is the average time required for display transition by switching the input
signal as below table and is based on Frame rate fV =60Hz to optimize.
Each time in below table is defined as Figure 2and shall be measured by switching the input
signal for “any level of gray(bright)”and “any level of gray(dark)”.
5. Definition of Transmittance (T%) :
Module is with white(L255) signal input
Transmittance =
Luminance of LCD Module
Ý 100 %
Luminance of BLU
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
15
A4(210 X 297)
www.panelook.com
Page 16
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
7.0 MECHANICAL CHARACTERISTICS
7.1 Dimensional Requirements
Figure 3 (located in Appendix) shows mechanical outlines for the model HV320WX2-600.
Other parameters are shown in Table 10.
< Table 10. Dimensional Parameters >
ParameterSpecificationUnit
Active area
Pixel pitch
Number of pixels
Weight 1180 (typ.) gram
1366(H) ശ768(V) (1 pixel = R + G + B dots)
697.685 (H) ശ392.256(V)
0.51(H) ശ0.51(V)
mm
mm
pixels
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
16
A4(210 X 297)
www.panelook.com
Page 17
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
8.0 Reliability Test Condition
< Table 12. Reliability Test Condition >
Item Test Condition
High-Temp/STG
Low-Temp/STG
High-Temp/HMD
High-Temp/OP
Ta = 60 ć, 240 hrs
Ta = -20 ć, 240 hrs
Ta = 50 ć, 80%RH, 240hrs
Ta = 50 ć, 240hrs
TFT LCD
REV ISSUE DATE
P0 2012.07.18
Low-Temp/OP
TST
Vibration
Shock
ESD
Ta = 0 ć, 240hrs
Ta = -2 0 ć ↔ 60 ć (0.5 hr), 100 cycle
Frequency:10-300 Hz
Gravity / AMP : 1.0 G rms
Period : X, Y, Z 30 min
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
19
A4(210 X 297)
www.panelook.com
Page 20
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
10.2 Packing Note
y Box Dimension : 875mmLÝ597mmWÝ279mmH
y Package Quantity in one Box : 20pcs
10.3 Box Label
y Label Size : 110 mm (L) u 55 mm (W)
y Contents
Model : HV320WX2-600
Q`ty : 20 Open Cell in one box.
Serial No. : Box Serial No. See next page for detail description.
Date : Packing Date
FG Code : FG Code of Product
REV ISSUE DATE
P0 2012.07.18
HV320WX2-600
0000000000000
00 0 00 0 0 000000
Type Grade Year Month ITEM-CODE Serial_no
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
XXXX
20
201X.X.XX
Internal CODE
RoHS Mark
PAGE
of 23
20
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
A4(210 X 297)
www.panelook.com
Page 21
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
12.0 HANDLING & CAUTIONS
CAUTIONS
(1) Cautions when taking out the Panel
Pick the pouch only, when taking out panel from a shipping package.
(2) Cautions for handling the panel
As the electrostatic discharges may break the LCD Panel, handle the LCD panel with
care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
As the LCD panel and back -light element are made from fragile glass material, impulse
and pressure to the LCD panel should be avoided.
As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth
without chemicals for cleaning.
Do not pull the interface connector in or out while the LCD panel is operating.
Put the panel display side down on a flat horizontal plane.
Handle connectors and cables with care.
(3) Cautions for the operation
When the panel is operating, do not lose CLK, ENAB signals. If any one of these
signals Is lost, the LCD panel would be damaged.
Obey the supply voltage sequence. If wrong sequence is applied, the panel would be
damaged.
(4) Cautions for the atmosphere
Dew drop atmosphere should be avoided.
Do not store and/or operate the LCD panel in a high temperature and/or humidity
atmosphere. Storage in an electro-conductive polymer packing pouch and under
relatively low temperature atmosphere is recommended.
(5) Cautions for the panel characteristics
Do not apply fixed pattern data signal to the LCD panel at product aging.
Applying fixed pattern for a long time may cause image sticking.
(6) Other cautions
Do not disassemble and/or re-assemble LCD panel.
Do not re-adjust variable resistor or switch etc.
When returning the panel for repair or etc., Please pack the panel not to be broken. We
recommend to use the original shipping packages.
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
21
A4(210 X 297)
www.panelook.com
Page 22
Global LCD Panel Exchange Center
www.panelook.com
13.0 APPENDIX
PRODUCT GROUP
TFT LCD
< Figure 1. Measurement Set Up >
REV ISSUE DATE
P0 2012.07.18
wy^ZWG
< Figure 2. Response Time Testing >
ڃڧٻژٻڐڋھۈ ڄٻ
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
22
A4(210 X 297)
www.panelook.com
Page 23
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT LCD
REV ISSUE DATE
P0 2012.07.18
< Figure 3. Open Cell Outline Dimensions (Front View) >
䚯䇙ฏ
䚯䇙ฏ
SPEC. NUMBER SPEC. TITLE
HV320WX2-600 Preliminary Product Specification
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
of 23
23
A4(210 X 297)
www.panelook.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.