BOE HV320WX2-261 Specification

Page 1
TITLE:
PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF BOE DT AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE DT AND MUST BE RETURNED TO BOE DT UPON ITS REQUEST
HV320WX2-261 Product Specification
BEIJING BOE DISPLAY TECHNOLOGY
SPEC. NUMBER
S63-8002
B2010-8002-O (1/3)
PRODUCT GROUP
TFT LCD
0
ISSUE DATE
2011.11. 01
PAGE
of 26
1
A4(210 X 297)
A4(210 X 297)
Page 2
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
REVISION HISTORY
REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED
0 - Initial Release 2011.11.01 Wu Xingji
SPEC. NUMBER
S63-8002
B2010-8002-O (2/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
2
A4(210 X 297)
Page 3
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
Contents
No ITEM Page
REVISIONS HISTORY 2 CONTENTS
1 GENERAL DESCRIPTION
1.1 Introduction
1.2 Features
1.3 Applications
1.4 General Specification 2 ABSOLUTE MAXIMUM RATINGS 6 3 ELECTRICAL SPECIFICATIONS 7
3.1 TFT LCD Open Cell 4 INTERFACE CONNECTION 8
3 4
4.1 Open Cell Input Signal & Power
4.2 LVDS Interface 5 SIGNAL TIMING SPECIFICATIONS
5.1 Timing Parameters
5.2 Signal Timing Waveform
5.3 Input Signals, Basic Display Colors & Cray Scale Of Colors
5.4 Power Sequence 6 OPTICAL SPECIFICATIONS 15 7 MECHANICAL CHARACTERISTICS 17 8 RELIABILITY TEST CONDITION 18 9 PRODUCT SERIAL NUMBER 19
10 PACKING INFORMATION
11 HANDING & CAUTIONS 22 12 APPENDIX
11
20
23
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
3
A4(210 X 297)
Page 4
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
1.0 GENERAL DESCRIPTION
1.1 Introduction
HV320WX2-261 is a color active matrix TFT LCD open cell using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This open cell has a 31.51 inch diagonally measured active area with WXGA resolutions (1366 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical stripe and this open cell can display 16.7M colors. The TFT-LCD panel used for
this open cell is adapted for a low reflection and higher color type.
RGB(Mini-LVDS)
VDD
+12.0V
LVDS
5pairs
BIST
# 20
LVDS_SEL
# 21
CN1
(30pin)
Timing Controller
[LVDS Rx & Mini-LVDS
Tx integrated]
Gate Driver Circuit
S1 S1366
G1
Source Driver Circuit
TFT - LCD Panel
(1366 × RGB × 768 pixels)
Power Circuit
Block
G768
1.2 Features
LVDS interface with 1 pixel / clockHigh-speed response Low color shift image quality8-bit color depth, display 16.7M colorsHigh luminance and contrast ratio, low reflection and wide viewing angleDE (Data Enable) only modeAFFS technology is applied for high display qualityRoHS compliant
SPEC. NUMBER
S63-8002
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
4
B2010-8002-O (3/3)
A4(210 X 297)
Page 5
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
1.3 Application
Home Alone Multimedia TFT-LCD TVDisplay Terminals for Control SystemHigh Definition TV(HD TV)AV application Products
1.4 General Specification
< Table 1. General Specifications >
Parameter Specification Unit Remark
Active area
697.685(H) × 392.256(V)
0 2011.11.01
mm
Number of pixels
Pixel pitch
Pixel arrangement Pixels RGB Vertical stripe
Display colors 16.7M(8bits-true) colors
Display mode Transmission mode, Normally Black
Open Cell
Transmittance
Weight 1180 (typ.) gram
Power Consumption 4.0 (typ.) Watt
Surface Treatment
170.25(H) × RGB× 510.75(V)
Haze 10%, 3H, Semi-glare or Anti-
glare treatment (Front Polarizer)
1366(H) × 768(V)
5.9 (typ.) %
Clear (Bottom Polarizer)
pixels
At center point with BOE BLU
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
5
A4(210 X 297)
Page 6
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. Open Cell Electrical Specifications >
Parameter Symbol Min. Max. Unit Remark
Power Supply Voltage VDD VSS-0.3 13.2 V
T
Operating Temperature
T Storage Temperature T Operating Ambient
Humidity
Hop 10 80 %RH
OP
SUR
ST
0 +50 0 +60
-20 +60
[VSS=GND=0V]
Ta = 25
Note 1
Storage Humidity Hst 10 80 %RH
Note 1 : Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 max. and no condensation of water.
80%
60
60%
Wet Bulb Temperature [C]
10
0
10 20 30 40 50 60 70 800-20
Dry Bulb Temperature [°C]
20
50
40
40%
30
Humidity [(%)RH]
10%
Storage
Operation
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
6
A4(210 X 297)
Page 7
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
3.0 ELECTRICAL SPECIFICATIONS
3.1 TFT LCD Open Cell
< Table 3. Open Cell Electrical Specifications >
Parameter Symbol
Power Supply Input Voltage VDD 10.8 12 13.2 Vdc Power Supply Ripple Voltage VRP 300 mV Power Supply Current IDD - 333 592 mA Power Consumption PDD 4.0 7.1 Watt Rush current IRUSH - - 3.0 A Note 2
LVDS
Interface
Differential Input High Threshold Voltage
Differential Input Low
Threshold Voltage
VLVTH +100 +300 mV
VLVTL -300 -100 mV
Min Typ Max
Values
[Ta =25± 2 ]
Unit Remark
Note 1
Common Input Voltage VLVC 1.0 1.2 1.4 V
CMOS Interface
Input High Threshold Voltage Input Low Threshold
VIH 2.7 - 3.3 V
VIL 0 - 0.6 V
Voltage
Note 1 : The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=12.0V, Frame rate fV=60Hz and Clock frequency = 75.4MHz. Test Pattern of power supply current
a) Typ : Mosaic 8 x 6 Pattern(L0/L255) b) Max : Skip 1H2V Sub Dot
Pattern(L0/L255)
Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min)
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
7
A4(210 X 297)
Page 8
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
4.0 INTERFACE CONNECTION
4.1 Module Input Signal & Power
4.1.1 LVDS Connector
- Connector : Fw10039-30(Manufactured by Foosung) or Equivalent.
< Table 4. Open Cell LVDS Input Connector Pin Configuration >
Pin
No
1
2
3
4
5 6
7 8
9 10 11 12 13 14 15
Symbol Description
NC No Connection
SCL SCL SDA SDA GND Ground
RXIN0-
RXIN0+
GND
RXIN1-
RXIN1+
GND
RXIN2-
RXIN2+
GND
RXCLKIN-
RXCLKIN+
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
Ground
LVDS Receiver Clock Signal(-)
LVDS Receiver Clock Signal(+)
Pin
No
16
17
18
19
20 21
22 23 24 25 26 27 28 29 30 VCC
Symbol Description
GND
RXIN3-
RXIN3+
GND Power Ground
NC NC
WP Write Protection GND Power Ground GND Power Ground GND Power Ground
VCC VCC VCC VCC
0 2011.11.01
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
No Connection No Connection
Power Supply : +12V
Notes : 1. NC(Not Connected) : These pins are only used for BOE internal operations.
2. Input Level of LVDS signal is based on the IEA 664 Standard.
3. LVDS data format: According to SEC VD request, JEIDA format is adopted.
SPEC. NUMBER
S63-8002
SPEC. TITLE
HV320WX2-261 Product Specification
B2010-8002-O (3/3)
PAGE
of 26
8
A4(210 X 297)
Page 9
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
4.0 INTERFACE CONNECTION
4.1 Module Input Signal & Power
4.1.2 Aging Connector
- Connector : 12507WR-H10G(Manufactured by YEONHO)or Equivalent.
< Table 5. Open Cell Aging Connector Pin Configuration >
Pin
No
1 2 3 4
Symbol Description
VCC VCC
GND GND
Aging_EN Aging Mode Enable
Power Supply : +12V
Pin
No
6 7 8 9
Symbol Description
SDA
SCL
GND
NC NC
0 2011.11.01
SDA
SCL
GND
5
Notes : 1. NC(Not Connected) : This pins are only used for BOE internal operations.
toggling.
WP
2. Aging _ EN : This pin is used for selecting display pattern mode when input DE or input CLOCK quits
If this Pin : Low (GND) Aging mode(BIST Mode) Otherwise : High( 3.3V) or Open (NC) Free run mode(Black Data)
Sequence : On = VDD ≥LVDS Option , BIST Option ≥Interface signal
Off = Interface signal ≥ LVDS Option , BIST Option ≥ VDD
Rear view of LCM
1
FW10039-30(Foosung)
Write Protection
30
10
NC
Aging(BIST) Pattern
NC
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
9
A4(210 X 297)
Page 10
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
4.2 LVDS Interface
- LVDS Receiver : Timing Controller (LVDS Rx merged) / LVDS Data : Pixel Data < Table 6. Open Cell Input Connector Pin Configuration >
LVDS Pin Vesa Data format JEIDA Data format Remark
TxIN/RxOUT0 Red0 [LSB] R2 TxIN/RxOUT1 Red1 R3 TxIN/RxOUT2 Red2 R4
TxOUT/RxIN0
TxOUT/RxIN1
TxIN/RxOUT3 Red3 R5 TxIN/RxOUT4 Red4 R6 TxIN/RxOUT6 Red5 R7 [MSB] TxIN/RxOUT7 Green0 [LSB] G2 TxIN/RxOUT8 Green1 G3
TxIN/RxOUT9 Green2 G4 TxIN/RxOUT12 Green3 G5 TxIN/RxOUT13 Green4 G6
TxOUT/RxIN2
TxOUT/RxIN3
TxIN/RxOUT14 Green5 G7 [MSB] TxIN/RxOUT15 Blue0 [LSB] B2 TxIN/RxOUT18 Blue1 B3 TxIN/RxOUT19 Blue2 B4 TxIN/RxOUT20 Blue3 B5 TxIN/RxOUT21 Blue4 B6 TxIN/RxOUT22 Blue5 B7 [MSB] TxIN/RxOUT24 HSYNC HSYNC TxIN/RxOUT25 VSYNC VSYNC TxIN/RxOUT26 DEN DEN
TxIN/RxOUT27 Red6 R0 [LSB]
TxIN/RxOUT5 Red7 [MSB] R1 TxIN/RxOUT10 Green6 G0 [LSB]
TxIN/RxOUT11 Green7 [MSB] G1
TxIN/RxOUT16 Blue6 B0 [LSB] TxIN/RxOUT17 Blue7 [MSB] B1
TxIN/RxOUT23 Reserved Reserved
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
10
A4(210 X 297)
Page 11
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
5.0 SIGNAL TIMING SPECIFICATION
5.1 Timing Parameters (DE only mode)
< Table 7. Timing Table >
ITEM Symbol Min Typ Max Unit Note
Period t
CLK
Frequency - 56 75.4 85.0 MHz Period t
Hsync
Frequency f
Period t
Vsync
Frequency f
CLK
HP
H
VP
V
0 2011.11.01
11.8 13.3 17.9 ns
1450 1560 2000 t
CLK
39.4 48.4 55 KHz
778 806 1200 t
HP
47 60 65 Hz
Horizontal
Valid t
HV
- 1366 - t
CLK
Active
Display Term
Vertical Active
Display Term
Notes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal operation.
Total t Valid t
Total t
HP
VV
VP
1450 1560 2000 t
- 768 - t
778 806 1200 t
CLK
HP
HP
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
11
A4(210 X 297)
Page 12
PRODUCT GROUP
REV ISSUE DATE
5.2 Signal Timing Waveform
DCLK
tCLK
First data
Second data
DE(Data Enable)
0.5 VDD
Invalid data
Invalid data
TFT LCD
Valid data
Pixel data
Pixel data
Pixel data
Valid data
Pixel data
0 2011.11.01
Invalid data
Invalid data
HSync
DE(Data Enable)
VSync
DE(Data Enable)
SPEC. NUMBER
S63-8002
tHP
tHV
tVP
tVV
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
12
B2010-8002-O (3/3)
A4(210 X 297)
Page 13
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
5.3 Input Signals, Basic Display Colors and Gray Scale of Colors
< Table 8. Input Signal and Display Color Table >
Color & Gray Scale
Basic
Colors
Gray Scale of Red
Gray Scale of Green
Gray Scale of Blue
Gray Scale of White
△ ▽
△ ▽
△ ▽
△ ▽
R6
0
R5
0
R4
0
R3
0
0R20
Input Data Signal
G6
R0
R1 B7G7R7
0
0
G0
0G50G40G30G20G10
0B60B50B40B30B20B10
000Black
Blue DataGreen DataRed Data
B0
000000000000000000000000Black 111111110000000000000000Blue 000000001111111100000000Green
111111111111111100000000Cyan
000000000000000011111111Red 111111110000000011111111Magenta 000000001111111111111111Yellow 111111111111111111111111White 000000000000000000000000Black 000000000000000010000000 000000000000000001000000Darker
↑ ↓
000000000000000010111111Brighter 000000000000000001111111 000000000000000011111111Red
000000000000000000000000Black
000000001000000000000000 000000000100000000000000Darker
↑ ↓
000000001011111100000000Brighter 000000000111111100000000 000000001111111100000000Green 000000000000000000000000Black 100000000000000000000000 010000000000000000000000Darker
↑ ↓
101111110000000000000000Brighter 011111110000000000000000 111111110000000000000000Blue
100000001000000010000000 010000000100000001000000Darker
↑ ↓
101111111011111110111111Brighter 01111110111111101111111
1
111111111111111111111White
111
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
13
A4(210 X 297)
Page 14
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
5.4 Power Sequence
To prevent a latch-up or DC operation of the Open Cell, the power on/off sequence shall
be as shown in below
< Table 9. Sequence Table >
Parameter
T1 0.5 - 20 ms T2 0 - 50 ms T3 200 - - ms
T4 200 - - ms
T5 0 - 50 ms T6 1 - - s
Notes: 1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
2. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER
S63-8002
SPEC. TITLE
Min Typ Max
HV320WX2-261 Product Specification
Values
Units
PAGE
of 26
14
B2010-8002-O (3/3)
A4(210 X 297)
Page 15
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
6.0 OPTICAL SPECIFICATIONS
The test of optical specifications shall be measured in a dark room (ambient luminance1 lux
and temperature=252) with the equipment of Luminance meter system (Goniometer system and PR730) and test unit shall be located at an approximate distance 50cm from the
LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θ
o’clock direction (the “right”), θ ) as the 9 o’clock direction (“left”) and θ
(= θ12) as the 12 o’clock direction (“upward”), θ
Ø=90
(= θ6 ) as the 6 o’clock direction (“bottom”). While
Ø=270
scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay
fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be
12.0V +/-10% at 25C. Optimum viewing angle direction is 6 ’clock. < Table 10. Optical Table >
[VDD = 12.0V, Frame rate = 60Hz, Ta =25± 2 ]
Parameter Symbol Condition Min Typ Max Unit Remark
Viewing
Horizontal
Angle
Vertical
Contrast ratio CR
Θ
Θ
Θ
Θ
12
3 9
6
CR > 10
900:1 1200:1 - Note 2
89 Deg. 89 Deg. 89 Deg. 89 Deg.
Ø=0
(=θ
3
) as the 3
Ø=180
Note 1
(= θ
9
White
W W
Red
Reproduction
of color
R G
Green
G
Blue
Response Time G to G T
R
B B
x
y
x
y
x y
x
Θ = 0
(Center)
Normal
Viewing
Angle
With BOE
TYP.
- 0.03
Module
y
g
- 8 10 ms Note 4
0.280
0.290
0.630
0.340
0.300
0.630
0.148
0.068
TYP.
Note 3
+ 0.03
Gamma Scale 2.0 2.2 2.4
Cell Transmittance 5.9 % Note 5
Note : There will be less than 3 times of Black Luminance Difference between Center and
each 4 Corners.
4 corners position is described in Appendix Figure.4
SPEC. NUMBER
S63-8002
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
15
of 26
B2010-8002-O (3/3)
A4(210 X 297)
Page 16
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
direction with respect to the optical axis which is normal to the LCD surface.
2. Contrast measurements shall be made at viewing angle of = 0and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See Figure 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically.
CR =
3. The color chromaticity coordinates specified in Table 9.shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel.
4. Response time Tg is the average time required for display transition by switching the input signal as below table and is based on Frame rate fV =60Hz to optimize. Each time in below table is defined as Figure 2and shall be measured by switching the input
signal for “any level of gray(bright)”and “any level of gray(dark)”.
Luminance when displaying a white raster Luminance when displaying a black raster
5. Definition of Transmittance (T%) :
Module is with white(L255) signal input
Transmittance =
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
Luminance of LCD Module
Luminance of BLU
SPEC. TITLE
HV320WX2-261 Product Specification
× 100 %
PAGE
of 26
16
A4(210 X 297)
Page 17
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
7.0 MECHANICAL CHARACTERISTICS
7.1 Dimensional Requirements
Figure 3 (located in Appendix) shows mechanical outlines for the model HV320WX2-261.
Other parameters are shown in Table 10.
< Table 11. Dimensional Parameters >
Parameter Specification Unit
Active area
Pixel pitch
Number of pixels
Weight 1180 (typ.) gram
1366(H) × 768(V) (1 pixel = R + G + B dots)
697.685 (H) × 392.256(V)
0.51(H) × 0.51(V)
mm mm
pixels
7.2 Semi-Glare and Polarizer Hardness
The surface of the LCD has an semi-glare coating to minimize reflection and a coating to
reduce scratching.
SPEC. NUMBER
S63-8002
SPEC. TITLE
HV320WX2-261 Product Specification
17
PAGE
of 26
B2010-8002-O (3/3)
A4(210 X 297)
Page 18
PRODUCT GROUP
REV ISSUE DATE
8.0 Reliability Test Condition
< Table 12. Reliability Test Condition >
Item Test Condition
High-Temp/STG
Low-Temp/STG
High-Temp/HMD
High-Temp/OP
Low-Temp/OP
TST
Ta = 60 , 240 hrs
Ta = -20 , 240 hrs
Ta = 50 , 80%RH, 240hrs
Ta = 50 , 240hrs Ta = 0 , 240hrs
Ta = -20 ↔ 60 (0.5 hr), 100 cycle
TFT LCD
0 2011.11.01
Frequency:10-300 Hz
Vibration
Shock
ESD
This test condition is based on BOE module.
Gravity / AMP : 1.0 G rms Period : X, Y, Z 30 min
Gravity : 50G Pulse width : 11msec, Half Sine
± X, ± Y, ± Z Once for each direction
Air:± 15kV,150pF/330Ω,100Point,1time/Point Contact:± 8kV,150pF/330Ω,100Point, 1time/Point
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
18
A4(210 X 297)
Page 19
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
9.0 PRODCUT SERIAL NUMBER
0 2011.11.01
HV320WX2-261
1 2 3 4 5 6 7
X X X X X X X X X X X X X X X X X
1. Control Number
2. Rank / Grade
3. Line Classification
4. Year (2011 : 11, 2012 : 12, …)
SPEC. NUMBER
S63-8002
SPEC. TITLE
HV320WX2-261 Product Specification
5. Month (1,2,3, … , 9, X, Y, Z)
6. Internal Use
7. Serial Number
PAGE
of 26
19
B2010-8002-O (3/3)
A4(210 X 297)
Page 20
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
10.0 PACKING INFORMATION
BOE provides the standard shipping container for customers, unless customer specifies
their packing information. The standard packing method and Barcode information are shown in below.
10.1 Packing Order
Up
Down
spacer
panel
spacer
Dense box
Packing method
Dense box packing method
stowagespacer + panel + spacer+...+Panel + spacer
Totalspacer21pcs
Panel20pcs
Inner box packing drawing
2 Dense Box/1 Inner Box
8 Inner Box/1 Pallet
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
20
A4(210 X 297)
Page 21
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
10.2 Packing Note
Box Dimension : 875mmL× 597mmW× 279mmHPackage Quantity in one Box : 20pcs
10.3 Box Label
Label Size : 110 mm (L) 55 mm (W)Contents
Model : HV320WX2-261 Q`ty : 20 Open Cell in one box. Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product
0 2011.11.01
00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no
SPEC. NUMBER
S63-8002
HV320WX2-261
0000000000000
SPEC. TITLE
HV320WX2-261 Product Specification
XXXX
20
201X.X.XX
Internal CODE
RoHS Mark
PAGE
of 26
21
B2010-8002-O (3/3)
A4(210 X 297)
Page 22
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
0 2011.11.01
11.0 HANDLING & CAUTIONS
CAUTIONS
(1) Cautions when taking out the Panel
Pick the pouch only, when taking out panel from a shipping package.
(2) Cautions for handling the panel
As the electrostatic discharges may break the LCD Panel, handle the LCD panel with
care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
As the LCD panel and back -light element are made from fragile glass material, impulse
and pressure to the LCD panel should be avoided.
As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth
without chemicals for cleaning. Do not pull the interface connector in or out while the LCD panel is operating. Put the panel display side down on a flat horizontal plane. Handle connectors and cables with care.
(3) Cautions for the operation
When the panel is operating, do not lose CLK, ENAB signals. If any one of these
signals Is lost, the LCD panel would be damaged.
Obey the supply voltage sequence. If wrong sequence is applied, the panel would be
damaged.
(4) Cautions for the atmosphere
Dew drop atmosphere should be avoided.
Do not store and/or operate the LCD panel in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended.
(5) Cautions for the panel characteristics
Do not apply fixed pattern data signal to the LCD panel at product aging. Applying fixed pattern for a long time may cause image sticking.
(6) Other cautions
Do not disassemble and/or re-assemble LCD panel. Do not re-adjust variable resistor or switch etc. When returning the panel for repair or etc., Please pack the panel not to be broken. We
recommend to use the original shipping packages.
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
22
A4(210 X 297)
Page 23
PRODUCT GROUP
(L = 5 0cm )
REV ISSUE DATE
12.0 APPENDIX
TFT LCD
< Figure 1. Measurement Set Up >
0 2011.11.01
PR730
< Figure 2. Response Time Testing >
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
23
A4(210 X 297)
Page 24
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
< Figure 3. Open Cell Outline Dimensions (Front View) >
0 2011.11.01
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
24
A4(210 X 297)
Page 25
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
< Figure 4. Optical Test 9 Point Location>
0 2011.11.01
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
PAGE
of 26
25
A4(210 X 297)
Page 26
PRODUCT GROUP
REV ISSUE DATE
TFT LCD
< Figure 5. TFT POL Protect Film Peeling Method >
0 2011.11.01
1. Be sure to peel off slowly(recommended more than 7sec) and constant speed.
2. Peeling direction shows in Figure 5.
3. Be sure to ground person with adequate methods such as the anti-static wrist band.
4. Be sure to ground S-PWB while peeling off the protection film.
5. Ionized air should be blown over during peeling action.
6. The protection film must not touch drivers and S-PWBs.
7. If adhesive may remain on the polarizer after the protection film peeling off, please remove with isopropyl-alcohol.
SPEC. NUMBER
S63-8002
B2010-8002-O (3/3)
SPEC. TITLE
HV320WX2-261 Product Specification
A4(210 X 297)
PAGE
of 26
26
Loading...