BOE HT215F01-100 Specification

Page 1

PROPRIETARY NOTE

THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HF AND MUST BE RETURNED TO BOE HF UPON ITS REQUEST

S864-6023

PRODUCT GROUP

TFT MODULE

Rev. A

ISSUE DATE

2011.7.19

TITLE : B3 HT215F01-100

Product Specification For Qisda

Rev. A

PAGE

OF30

HEFEI BOE OPTOELECTRONICS TECHNOLOGY

R2010-6053-O(1/3)

A4(210 X 297)

Page 2

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE A

SPEC. TITLE

S864-6023

B3 HT215F01-100 Product Specification For Qisda_ Rev.A

2011.7.19 PAGE

OF 30

REVISION HISTORY

REV. ECN No. DESCRIPTION OF CHANGES DATE PREPARED

A 2011.07.06 jiangweidongFrame Period 1149 lines→1251

lines

Initial Release

2011.07.04 jiangweidong

R2010-6053-O(2/3)

A4(210 X 297)

Page 3

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

Contents

No. Item Page

1.0 General Description 4

2.0 Absolute Maximum Ratings 6

3.0 Electrical Specifications 7

4.0 Optical Specifications 8

5.0 Interface Connection 10

6.0 Signal Timing Specifications 13

7.0 Signal Timing Waveforms of Interface Signal 15

8.0 Input Signals, Display Colors & Gray Scale of Colors 17

2011.7.19PRODUCT SPEC-TFT MODULE PAGE

OF 30

9.0 Power Sequence 18

10.0 Mechanical Characteristics 19

11.0 Reliability Test 20

12.0 Handling& Cautions 21

13.0 Product Serial Number 22

14.0 Packing 23

15.0 Appendix 25

A4(210 X 297)

Page 4

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

1.0 GENERAL DESCRIPTION

1.1 Introduction

HT215F01-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 21.5 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.

Connector (CN

LVDS Input Signal

LVDS Rx

T/CON

Mini LVDS Tx

Gate Driver

Source Driver

TFT LCD Panel

2011.7.19PRODUCT SPEC-TFT MODULE PAGE

OF 30

1920 ×××× 1080

VDD

)

1.2 Features

 LVDS Interface with 2 pixel / clock  High-speed response  6-bit (Hi-FRC) color depth, display 16. 7M colors  Incorporated edge type back-light (One Light Bar)  High luminance and contrast ratio, low reflection and wide viewing angle  DE (Data Enable) only  RoHS /TCO 5.0 Compliant

DC/DC

Gamma

Vcom

LED Light Bar

CN2

A4(210 X 297)

Page 5

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

1.3 Application

 Desktop Type of PC & Workstation Use  Slim-Size Display for Stand-alone Monitor  Display Terminals for Control System  Monitors for Process Controller

1.4 General Specification

The followings are general specifications at the model HT215F01-100.

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

2011.7.19PRODUCT SPEC-TFT MODULE PAGE

OF 30

Parameter Specification Unit

Active area 476.64(H) × 268.11 (V) mm Number of pixels 1920(H) ×1080(V) pixels Pixel pitch 0.24825(H) ×0.24825(V) mm Pixel arrangement RGB Vertical stripe Display colors 16.7M colors Display mode Normally White Dimensional outline 495.6(H) × 292.2(V) × 10.2(D) typ. mm Weight 1450 (typ.) g Surface Treatment Haze 25%, 3H Back-light Lower side 1-LED Light bar Type

Remarks

A4(210 X 297)

Page 6

PRODUCT GROUP

R2010

6053

O(3/3)

2 0

2 02 0

2 0

4 0

4 04 0

4 0

1 0 0

1 0 01 0 0

1 0 0

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

2.0 ABSOLUTE MAXIMUM RATINGS

The followings are maximum values which, if exceed, may cause faulty operation or

damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2.

< Table 2. Absolute Maximum Ratings>

Symbol Min. Max. Unit Remarks

Parameter

Power Supply Voltage V Logic Supply Voltage V Operating Temperature T Storage Temperature T

-0.5 5.5

VSS-0.3 VDD+0.3 V

0 +50

-20 +60

[VSS=GND=0V]

℃

2011.7.19PRODUCT SPEC-TFT MODULE

Ta = 25 ℃

PAGE

OF 30

Note : 1) Temperature and relative humidity range are shown in the figure below.

Wet bulb temperature should be 39 OC max. and no condensation of water.

8 0

8 08 0

6 0

6 06 0

O p e ra tin g R a n g e

O p e ra tin g R a n g eO p e ra tin g R a n g e

4 0

4 04 0

Relative Humidity (%RH)

-2 0

-2 0-2 0

2 0

2 02 0

S to ra g e R a n g e

S to ra g e R a n g eS to ra g e R a n g e

0000

T e m p e ra tu re (˚C )

T e m p e ra tu re (˚C )T e m p e ra tu re (˚C )

(39,90)

(50,50)

(60,30)

6 0

6 0 8 0

6 06 0

8 0-2 0

8 08 0

A4(210 X 297)

Page 7

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

B3 HT215F01-100 Product Specification For Qisda _Rev.A

3.0 ELECTRICAL SPECIFICATIONS

3.1Electrical Specifications

< Table 3. Electrical specifications >

Parameter Min. Typ. Max. Unit Remarks

SPEC. TITLE

Power Supply Voltage V Power Supply Current I In-Rush Current I Permissible Input Ripple Voltage V High Level Differential Input

Threshold Voltage Low Level Differential Input

Threshold Voltage Differential input voltage |VID| 200 - 600 mV

Differential input common mode voltage Vcm 1.0 1.2 1.5

RUSH

4.5 5.0 5.5 V

- 700 1400 mA

- - 3 A Note 2

- - 100 mV VDD= 5.0V

- - +100 mV

-100 - - mV

2011.7.19PRODUCT SPEC-TFT MODULE

[Ta =25±2 ℃]

Note1

VIH=100mV, VIL=-100mV

PAGE

OF 30

LED Channel Voltage V LED Channel Current I

LED Lifetime 30,000 - - Hrs IL=60 mA

Power Consumption

total

- 54.4 59.5 V

- 60 - mA

- 3.5 - W

- 13.06 - W IL=60 mA, Note 5

- 16.56 - W

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.

The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz. Test Pattern of power

supply current

a) Typ : Color Bar pattern b) Max : Skip Sub Pixel Pattern

2. Duration of rush current is about 2 ms and rising time of VDD is 520 μs ± 20 %

3. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display

4. The voltage above this value should be applied to the lamps for more than 1 second to start-up. Otherwise the

lamps may not be turned on.

5. Calculated value for reference (V

× IL) ×4(channel) excluding driver loss. (LED Light bar: 17S4P)

A4(210 X 297)

Page 8

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

2011.7.19PRODUCT SPEC-TFT MODULE PAGE

OF 30

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

4.0 OPTICAL SPECIFICATION

4.1 Overview

The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θ

θ9) as the 9 o’clock direction (“left”) and θ

Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock.

4.2 Optical Specifications

Viewing Angle range

Luminance Contrast ratio CR Luminance of White Y White luminance uniformity ΔY 75 80 % Note 4

(=θ3) as the 3 o’clock direction (the “right”), θ

Ø=0

Ø=270

(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or

(= θ12) as the 12 o’clock direction (“upward”), θ

Ø=90

[VDD = 5.0V, Frame rate = 60Hz, Clock = 78MHz, IBL= 7.5mA, Ta =25±2 ℃]

Parameter Symbol Condition Min. Typ. Max. Unit Remark

Horizontal

Vertical

Horizontal

Vertical

White

Red

Reproduction

of color

Green

Blue

Response

Time

Cross Talk CT - - 2.0 % Note 7

Rising T

Falling T

CR > 10

CR > 5

Θ = 0°

(Center)

Normal

Viewing

Angle

70 85 - Deg. 70 85 - Deg. 70 80 - Deg. 70 80 - Deg. 85 - - Deg. 85 - - Deg. 85 - - Deg.

85 - - Deg. 700 1000 Note 2 200 250 cd/m

0.283 0.313 0.343

0.299 0.329 0.359

0.609 0.639 0.669

0.312 0.342 0.372

0.293 0.323 0.353

0.600 0.630 0.660

0.123 0.153 0.183

0.021 0.051 0.081

1.5 2.5 ms

3.5 5.5 ms

Ø=180

Note 1

Note 3

Note 5

Note 6

A4(210 X 297)

Page 9

PRODUCT GROUP

R2010

6053

O(3/3)

ts ) * 100

REV

ISSUE DATE

2011.7.19PRODUCT SPEC-TFT MODULE PAGE

OF 30

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

Note :

1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface.

2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically.

CR =

3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display.

4. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9poin (See FIGURE 2 shown in Appendix).

5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel.

6. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.

7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix).

Luminance when displaying a white raster

Luminance when displaying a black raster

A4(210 X 297)

Page 10

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

B3 HT215F01-100 Product Specification For Qisda _Rev.A

5.0 INTERFACE CONNECTION.

5.1 Electrical Interface Connection

●

CN1 Module Side Connector : UJU IS100-L300-C23 or Equivalent

User Side Connector : JAE FI-X30H or Equivalent

Pin No Symbol Function Remark

SPEC. TITLE

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

RXO0- Negative Transmission data of Pixel 0 (ODD)

RXO0+ Positive Transmission data of Pixel 0 (ODD)

RXO1- Negative Transmission data of Pixel 1 (ODD)

RXO1+ Positive Transmission data of Pixel 1 (ODD)

RXO2- Negative Transmission data of Pixel 2 (ODD) RXO2+ Positive Transmission data of Pixel 2 (ODD)

GND Power Ground

RXOC- Negative Transmission Clock (ODD) RXOC+ Positive Transmission Clock (ODD) RXO3- Negative Transmission data of Pixel 3 (ODD)

RXO3+ PositiveTransmission data of Pixel 3 (ODD)

RXE0- Negative Transmission data of Pixel 0 (EVEN)

RXE0+ Positive Transmission data of Pixel 0 (EVEN)

GND Power Ground

RXE1- Negative Transmission data of Pixel 1 (EVEN)

RXE1+ Positive Transmission data of Pixel 1 (EVEN)

GND Power Ground

RXE2- Negative Transmission data of Pixel 2 (EVEN)

RXE2+ Positive Transmission data of Pixel 2 (EVEN)

RXEC- Negative Transmission Clock (EVEN)

RXEC+ Positive Transmission Clock (EVEN)

RXE3- Negative Transmission data of Pixel 3 (EVEN)

RXE3+ Positive Transmission data of Pixel 3 (EVEN)

GND Power Ground

NC Not connection, this pin should be open

2011.7.19PRODUCT SPEC-TFT MODULE

Note1

PAGE

OF 30

26 27 28 29 30

Note 1

Note 1：：：： This pin should be connected with GND

Note 1Note 1

This pin should be connected with GND

This pin should be connected with GNDThis pin should be connected with GND

NC Not connection, this pin should be open

NC Not connection VDD1 Power Supply:+5V VDD2 VDD3

A4(210 X 297)

Page 11

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

B3 HT215F01-100 Product Specification For Qisda _Rev.A

5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent)

5.2.1 ODD LVDS Interface

SPEC. TITLE

OUT0-

OUT1-

OUT2-

OUT3-

Interface

TFT-LCD

(Rx)

RXO0-

RXO0+

RXO1-

RXO1+

RXO2-

RXO2+

RXO CLK-

RXO CLK+

RXO3-

RXO3+

Input

Signal

OR0 OR1 OR2 OR3 OR4 OR5 OG0 OG1 OG2 OG3 OG4 OG5

O D D

L V D

OB0 OB1 OB2 OB3 OB4

OB5 Hsync Vsync

MCLK

OR6

OR7

OG6

OG7

OB6

OB7 RSVD

Transmitter Remark

Pin No.

51 52 54 55 56

3 4 6

7 11 12 14 15 19 20 22 23 24 27 28 30 31

8 10 16 18 25

Pin No.

48 47

46 45

42 41

40 39

38 37

System (Tx)

OUT0+

OUT1+

OUT2+

CLK OUT-

CLK OUT+

OUT3+

HT215F01-100

(CN11) Pin No.

1 2

3 4

5 6

8 9

10 11

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

A4(210 X 297)

Page 12

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

B3 HT215F01-100 Product Specification For Qisda _Rev.A

5.2.2 EVEN LVDS Interface

SPEC. TITLE

Input

Signal

ER0 ER1 ER2 ER3 ER4 ER5 EG0 EG1 EG2 EG3 EG4

E V E N

L V D

EG5 EB0 EB1 EB2 EB3 EB4

EB5 Hsync Vsync

MCLK

ER6

ER7

EG6

EG7

EB6

EB7 RSVD

Transmitter Remark

Pin No.

51 52 54 55 56

3 4 6

7 11 12 14 15 19 20 22 23 24 27 28 30 31

8 10 16 18 25

Pin No.

48 47

46 45

42 41

40 39

38 37

Interface

System (Tx)

OUT0-

OUT0+

OUT1-

OUT1+

OUT2-

OUT2+

CLK OUT-

CLK OUT+

OUT3-

OUT3+

TFT-LCD

(Rx)

RXE0RXE0+

RXE1RXE1+

RXE2RXE2+

RXE CLK-

RXE CLK+

RXE3RXE3+

HT215F01-100 (C

N11)

Pin No.

12 13

15 16

18 19

20 21

22 23

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

A4(210 X 297)

Page 13

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

5.3 Data Input Format

(1,1) (2,1) (1919,1) (1920,1)

R G B R G B R G B R G B

1 Pixel = 3 Dots

R G B

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

R G B R G B R G B R G B

(1,1080) (2,1080) (1919,1080) (1920,1080)

Display Position of Input Data (V-H)

5.4 Back-light Interface Connection

LED LightBar Connector●CN 2

Pin Function

Channel 1 Current Feedback

Channel 2 Current Feedback

LED Power Supply

Channel3 Current Feedback

Channel4 Current Feedback

:CI1406M1HRL-NH or equivalent

A4(210 X 297)

Page 14

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

6.0 SIGNAL TIMING SPECIFICATION

6.1

The HT215F01-100 is operated by the DE only.

Item Symbols Min Typ Max Unit

Frequency 1/Tc 57.5 74.32 94 MHz

Clock

Frame Period Tv

High Time Tch - 4/7 Tc Low Time Tcl - 3/7 Tc -

1091 1125 1251 lines

50 60 75 Hz

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

20 16.67 13.33 ms

Vertical Display Period Tvd - 1080 - lines

One line Scanning Period Th 1060 1100 1251 clocks

Horizontal Display Period Thd - 960 - clocks

A4(210 X 297)

Page 15

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

6.2 LVDS Rx Interface Timing Parameter

The specification of the LVDS Rx interface timing parameter is shown in Table 4.

Item Symbol Min Typ Max Unit Remark

CLKIN Period tRCIP 10.76 13.46 16.15 nsec

Input Data 0 tRIP1 -0.4 0.0 +0.4 nsec Input Data 1 tRIP0 tRCIP/7-0.4 tRCIP/7 tRCIP/7+0.4 nsec

Input Data 2 tRIP6 2 ×tRCIP/7-0.4 2 ×tRCIP/7 2 ×tRCIP/7+0.4 nsec Input Data 3 tRIP5 3 ×tRCIP/7-0.4 3 ×tRCIP/7 3 ×tRCIP/7+0.4 nsec Input Data 4 tRIP4 4 ×tRCIP/7-0.4 4 ×tRCIP/7 4 ×tRCIP/7+0.4 nsec Input Data 5 tRIP3 5 ×tRCIP/7-0.4 5 ×tRCIP/7 5 ×tRCIP/7+0.4 nsec Input Data 6 tRIP2 6 ×tRCIP/7-0.4 6 ×tRCIP/7 6 ×tRCIP/7+0.4 nsec

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

RXz +/-

* Z = 0, 1, 2,3

RxCLK+

tRIP2

tRIP3

tRIP4

tRIP5

tRIP6

tRIP0

tRIP1

Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0Rx3

tRCIP

* Vdiff = (RXz+)-(RXz-),…. ,(RXCLK+)-(RXCLK-)

Vdiff=0[v]Vdiff=0[v]

A4(210 X 297)

Page 16

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL

7.1 Sync Timing Waveforms

V-Sync

H-Sync

1) Need over 3 H-sync during V-Sync Low

2) Fix H-Sync width from V-Sync falling edge to first rising edge

Over 3 H-sync

Fix H-Sync width Area

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

7.2 Vertical Timing Waveforms

MCLK

R7 ~ R0

G7 ~ G0

B7 ~ B0

Invalid Data DataInvalid

x,1 x,2 x,y x+1,1

Tvd

x,1050

A4(210 X 297)

Page 17

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

B3 HT215F01-100 Product Specification For Qisda _Rev.A

7.3 Horizontal Timing Waveforms

MCLK

RA7 ~RA0

SPEC. TITLE

GA7 ~GA0

BA7 ~BA0

D1 D2 Dn Data D1 D2 D3

Thd

D1048 D1049 D1050

2011.7.19PRODUCT SPEC-TFT MODULE PAGE

OF 30

Invalid

MCLK

Data

Tch

Tds

Valid

Tes

2.0V

Tcl

1.5V

Tdh

Data

2.0V

0.8V

2.0V

0.8V

A4(210 X 297)

Page 18

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS

Color & Gray Scale

Basic Colors

Gray Scale of RED

Gray Scale of GREEN

Gray Scale of BLUE

Gray Scale of WHITE

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△

Darker 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△ ↑ ↑ ↑ ▽ ↓ ↓ ↓

Brighter 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

▽

Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△

Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0

△ ↑ ↑ ↑ ▽ ↓ ↓ ↓

Brighter 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0

▽

Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△

Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0

△ ↑ ↑ ↑ ▽ ↓ ↓ ↓

Brighter 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1

▽

Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

△

Darker 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0

△ ↑ ↑ ↑ ▽ ↓ ↓ ↓

Brighter 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1

▽

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

RED DATA GREEN DATA BLUE DATA

0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0

0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1

1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0

A4(210 X 297)

Page 19

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

9.0 POWER SEQUENCE

To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below

Power Supply

Interface Signal

0.9VDD

0.1VDD

Valid

0.9VDD

0.1VDD

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

T5 T6

Back- light

● 0.5 ms ≤ T1 ≤ 10 ms

● 0 ≤ T2 ≤ 50 ms

● 0 ≤ T3 ≤ 50 ms

● 1 sec ≤ T4

● 200 ms ≤ T5

● 200 ms ≤ T6

Notes:

1. When the power supply VDD is 0V, keep the level of input signals on the low or keep high impedance.

2. Do not keep the interface signal high impedance when power is on.

3. Back Light must be turn on after power for logic and interface signal are valid.

A4(210 X 297)

Page 20

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

10.0 MECHANICAL CHARACTERISTICS

10.1 Dimensional Requirements

FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT215F01-100. Other parameters are shown in Table 5.

Parameter Specification Unit

Dimensional outline Weight Active area Pixel pitch Number of pixels

495.6 ×292.2×10.2 1450 (typ.)

476.64(H) × 268.11(V)

0.24825(H) x 0.24825(V) 1920(H)×1080(V) (1 pixel = R + G + B dots)

2011.7.19PRODUCT SPEC-TFT MODULE

gram

mm mm

pixels

PAGE

OF 30

Back-light

Lower side 1-LED Light bar Type

10.2 Mounting

See FIGURE 5. (shown in Appendix)

10.3 Anti-Glare and Polarizer Hardness.

The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching.

10.4 Light Leakage

There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 350lux.

A4(210 X 297)

Page 21

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

11.0 RELIABLITY TEST

The Reliability test items and its conditions are shown in below.

No Test Items

High temperature storage test Ta = 60 ℃, 240 hrs

Low temperature storage test Ta = -20 ℃, 240 hrs

High temperature & high humidity

operation test High temperature operation test Ta = 50 ℃, 240hrs

Low temperature operation test Ta = 0 ℃, 240hrs

Thermal shock Ta = -20 ℃ ↔ 60 ℃ (0.5 hr), 100 cycle

Ta = 50 ℃, 80%RH, 240hrs

Conditions

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

Vibration test

(non-operating)

Shock test

(non-operating)

Electro-static discharge test

(non-operating)

10 Altitude test

Frequency 10 ~ 300 Hz, Sweep rate 30 min Gravity / AMP 1.5 G Period X, Y, Z 30 min

Gravity

Pulse width

Direction ± X, ± Y, ± Z Once for each

Air : 150 pF, 330Ω, 15 KV Contact : 150 pF, 330Ω, 8 KV

50G

11msec, sine wave

Operating: 0 to 16400ft , 0 to 40° Non Operating: 0 to 40000ft, -20 to 40°

A4(210 X 297)

Page 22

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

12.0 HANDLING & CAUTIONS

(1) Cautions when taking out the module

 Pick the pouch only, when taking out module from a shipping package.

(2) Cautions for handling the module

 As the electrostatic discharges may break the LCD module, handle the LCD

module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible.

 As the LCD panel and back - light element are made from fragile glass material,

impulse and pressure to the LCD module should be avoided.

 As the surface of the polarizer is very soft and easily scratched, use a soft dry

cloth without chemicals for cleaning.

 Do not pull the interface connector in or out while the LCD module is operating.  Put the module display side down on a flat horizontal plane.  Handle connectors and cables with care.

(3) Cautions for the operation

 When the module is operating, do not lose CLK, ENAB signals. If any one of

these signals is lost, the LCD panel would be damaged.

 Obey the supply voltage sequence. If wrong sequence is applied, the module

would be damaged.

(4) Cautions for the atmosphere

 Dew drop atmosphere should be avoided.  Do not store and/or operate the LCD module in a high temperature and/or

humidity atmosphere. Storage in an electro-conductive polymer packing pouch

and under relatively low temperature atmosphere is recommended.

(5) Cautions for the module characteristics

 Do not apply fixed pattern data signal to the LCD module at product aging.  Applying fixed pattern for a long time may cause image sticking.

(6) Other cautions

 Do not disassemble and/or re-assemble LCD module.  Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be

broken. We recommend to use the original shipping packages.

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

A4(210 X 297)

Page 23

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

13.0 PRODUCT SERIAL NUMBER

HT215F01-100

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

1 2 3 4 5 6 7

X X X X X X X X X X X X X X X X X

1. Control Number

2. Rank / Grade

3. Line Classification

4. Year (2001 : 01, 2002 : 02, …)

5. Month (1,2,3, … , 9, X, Y, Z)

6. Internal Use

7. Serial Number

A4(210 X 297)

Page 24

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

14.0 Packing

14.1 Packing Order

Put EPE Cushion into the box

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

As shown in the figure, place the modules bundled by packing bag In the box

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

After sealing the box, attach Packing Label on the attach position sign area of the box.

Place EPE cover on top of the box

A4(210 X 297)

Page 25

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

14.2 Pallet Packing Order

Load Pallet in correct position

Box cover

Polyester bend

2011.7.19PRODUCT SPEC-TFT MODULE

Pile up the unit Box filled with Modules on the Pallet carefully not to make a space.

PAGE

OF 30

Out box

Adjust Outer box to piling Boxes and cover the Outer box using box cover. Bend Pallet Assy which is putting the Box Cover tight in two direction (horizontal and vertical) and two times using Polyester bend.

Wrap the Pallet Assy loaded 1story, 2stories from downside through side and to edge of upside. (12Boxes/Pallet)

A4(210 X 297)

Page 26

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

14.3 Packing Specification and Note

Specification

Item

Panel 1

Cushion 1 - 0.70 -

Box 1 558(L)mm x 348(W)mm x 400(H)mm 0.70 without Panel & cushion

Packing Box

Pallet 1

Pallet after Packing

Q'ty Dimension Weight (kg)

10pcs/Bo

12boxes/

pallet

495.6(H) × 292.2(V) × 10.2(D) typ.

558(L)mm x 348W)mm x 400(H)mm 16.20 with panel & cushion

1200(L)mm x 1140(W)mm x 120(H)m

1140(L)mm x 1076W)mm x 820(H)mm 214 -

1.48 -

15.90 -

14.3 Box label

 Label Size : 108 mm (L) × 56 mm (W)  Contents

Model : HT215F01-100 Q`ty : Module Q`ty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product

2011.7.19PRODUCT SPEC-TFT MODULE PAGE

Remark

OF 30

HT215F01-100

0000000000000

5940

00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no

201X.X.XX

FG CODE

RoHS Mark

A4(210 X 297)

Page 27

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

15.0 APPENDIX

Figure 1. Measurement Set Up

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

(L = 50 c m )

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

Figure 2. White Luminance and Uniformity Measurement Locations (9 points)

192 960 1728

108

540

972

A4(210 X 297)

Page 28

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

Display data

Optical Response

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

Figure 3. Response Time Testing

White(TFT OFF)

100%

90%

10%

Black(TFT ON)

White(TFT OFF)

Time

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

Figure 4. Cross Modulation Test Description

VIEW AREA VIEW AREA

(D/4, W/4)

L31

(3D/4, 3W/4)

(D, W)

YA(7D/8,W/2)

(D, W)

Cross-Talk (%) = × 100

YB- Y

Where: YA= Initial luminance of measured area (cd/m2)

YB= Subsequent luminance of measured area (cd/m2)

The location measured will be exactly the same in both patterns

YB(7D/8,W/2)

A4(210 X 297)

Page 29

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

Figure 5. TFT-LCD Module Outline Dimensions (Front view)

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

( )

A4(210 X 297)

Page 30

PRODUCT GROUP

R2010

6053

O(3/3)

REV

ISSUE DATE

S864-6023

SPEC. TITLE

B3 HT215F01-100 Product Specification For Qisda _Rev.A

Figure 6. TFT-LCD Module Outline Dimensions (Rear view)

2011.7.19PRODUCT SPEC-TFT MODULE

PAGE

OF 30

A4(210 X 297)