BOE HR215WU1-120 Specification

Page 1

PROPRIETARY NOTE

THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HF AND MUST BE RETURNED TO BOE HF UPON ITS REQUEST

SPEC. NUMBER

PRODUCT GROUP

TFT MODULE

Rev. O

ISSUE DATE

2012.10.18

TITLE : B3 HR215WU1-120

Product Specification

Rev. O

PAGE

OF30

HEFEI BOE OPTOELECTRONICS TECHNOLOGY

R2010-6053-O(1/3)

A4(210 X 297)

Page 2

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

PRODUCT SPEC-TFT MODULE O

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

2012.10.18 PAGE

OF 30

REVISION HISTORY

REV. ECN No. DESCRIPTION OF CHANGES DATE PREPARED

O Initial Release 2012.10.18 Xudong Wang

R2010-6053-O(2/3)

A4(210 X 297)

Page 3

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

No. Item Page

1.0 General Description 4

2.0 Absolute Maximum Ratings 6

3.0 Electrical Specifications 7

4.0 Optical Specifications 8

5.0 Interface Connection 10

6.0 Signal Timing Specifications 13

7.0 Signal Timing Waveforms of Interface Signal 15

8.0 Input Signals, Display Colors & Gray Scale of Colors 17

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

Contents

2012.10.18 PAGE

OF 30

9.0 Power Sequence 18

10.0 Mechanical Characteristics 19

11.0 Reliability Test 20

12.0 Handling& Cautions 21

13.0 Product Serial Number 22

14.0 Packing 23

15.0 Appendix 25

R2010-6053-O(3/3)

A4(210 X 297)

Page 4

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

1.0 GENERAL DESCRIPTION

1.1 Introduction

HR215WU1-120 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 21.5 inch diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.

Connector (CN

LVDS Input Signal

LVDS Rx

T/CON

Mini LVDS Tx

Gate Driver

Source Driver

TFT LCD Panel

2012.10.18 PAGE

OF 30

1920 × 1080

VDD

)

1.2 Features

z LVDS Interface with 2 pixel / clock z High-speed response z 6-bit (Hi-FRC) color depth, display 16. 7M colors z Incorporated edge type back-light (One Light Bar) z High luminance and contrast ratio, low reflection and wide viewing angle z DE (Data Enable) only z RoHS /TCO 6.0 ,ES6.0 Compliant

R2010-6053-O(3/3)

DC/DC

Gamma

Vcom

LED Light Bar

CN2

A4(210 X 297)

Page 5

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

1.3 Application

z Desktop Type of PC & Workstation Use z Slim-Size Display for Stand-alone Monitor z Display Terminals for Control System z Monitors for Process Controller

1.4 General Specification

The followings are general specifications at the model HR215WU1-120.

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

2012.10.18 PAGE

OF 30

Parameter Specification Unit

Active area

Number of pixels

Pixel pitch

Pixel arrangement RGB Vertical stripe -

Display colors 16.7M colors

Display mode Normally Black -

Dimensional outline

Weight 1900 (typ.) g

Surface Treatment

Back-light

476.64(H) × 268.11 (V)

1920(H) ×1080(V)

0.24825(H) ×0.24825(V)

495.6(H) × 292.2(V) × 10.7(D) typ.

Anti-glare, 3H

Lower side 1-LED Light bar Type

pixels

Remarks

R2010-6053-O(3/3)

A4(210 X 297)

Page 6

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

2.0 ABSOLUTE MAXIMUM RATINGS

The followings are maximum values which, if exceed, may cause faulty operation or

damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2.

< Table 2. Absolute Maximum Ratings> [VSS=GND=0V]

Symbol Min. Max. Unit Remarks

Parameter

Power Supply Voltage V

Logic Supply Voltage V

Operating Temperature T

Storage Temperature T

-0.5 5.5

VSS-0.3 VDD+0.3 V

0+50

-20 +60

℃

2012.10.18 PAGE

OF 30

Ta = 25 ℃

Note : 1) Temperature and relative humidity range are shown in the figure below.

Wet bulb temperature should be 39 OC max. and no condensation of water.

100

O perating Range

Relative Humidity (%RH)

Storage R ange

20 40 60 80-20

Tem perature (˚C)

(39,90)

(50,50)

(60,30)

R2010-6053-O(3/3)

A4(210 X 297)

Page 7

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

3.0 ELECTRICAL SPECIFICATIONS

3.1Electrical Specifications

< Table 3. Electrical specifications >

Parameter Min. Typ. Max. Unit Remarks

Power Supply Voltage V

Power Supply Current I

In-Rush Current I

Permissible Input Ripple Voltage V

High Level Differential Input Threshold Voltage

Low Level Differential Input Threshold Voltage

Differential input voltage |V

Differential input common mode voltage Vcm 1.0 1.2 1.5

RUSH

| 200 - 600 mV

4.5 5.0 5.5 V

- 800 1400 mA

--3ANote 2

--200 mV V

- - +100 mV

-100 - - mV

2012.10.18

[Ta =25±2 ℃]

Note1

= 5.0V

VIH=100mV, VIL=-100mV

PAGE

OF 30

LED Voltage V

LED Channel Voltage V

LED Channel Current I

LED Lifetime 30,000 - - Hrs I

Power Consumption

total

3.05

45.75 48 51 V

-60-mA

- 4.9 6.25 W

- 11.52 12.24 W I

- 16.42 18.49 W

3.2

3.4 V

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.

The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz. Test Pattern of power

supply current

a) Typ : Color Bar pattern b) Max : Skip Sub Pixel Pattern

2. Duration of rush current is about 2 ms and rising time of VDD is 520 μs ± 20 %

3. The lamp frequency should be selected as different as possible from the horizontal

synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display

4. Calculated value for reference (V

× IL) ×4(channel) excluding driver loss. (LED Light bar: 15S4P)

=60 mA

=60 mA, Note 4

R2010-6053-O(3/3)

A4(210 X 297)

Page 8

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

2012.10.18 PAGE

4.0 OPTICAL SPECIFICATION

4.1 Overview

The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature =

25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to

(=θ3) as the 3 o’clock direction (the “right”), θ

Ø=0

the 9 o’clock direction (“left”) and θ

(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the

Ø=270

center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock.

4.2 Optical Specifications

[VDD = 5.0V, Frame rate = 60Hz, Clock = 78MHz, IBL= 120mA, Ta =25±2 ℃]

Parameter Symbol Condition Min. Typ. Max. Unit Remark

Horizontal

Viewing Angle range

Vertical

Horizontal

Viewing Angle range

Vertical

Luminance Contrast ratio CR

Luminance of White Y

White luminance uniformity ΔY 75 80 - % Note 4

White

Red

Reproduction

of color

Green

Blue

Response

Time

Cross Talk CT - - 2.0 % Note 7

Rising+Fal

ling

(= θ12) as the 12 o’clock direction (“upward”), θ

Ø=90

-89-Deg.

CR > 10

CR > 5

Θ = 0°

(Center)

Normal

Viewing

Angle

-89-Deg.

700 1000 - Note 2

200 250 - cd/m

0.283 0.313 0.343

0.299 0.329 0.359

0.617 0.647 0.677

0.309 0.339 0.369

0.277 0.307 0.337

0.603 0.633 0.663

0.116 0.146 0.176

0.026 0.056 0.086

14 21 ms Note 6

Ø=180

OF 30

(= θ9) as

Note 1

Note 3

Note 5

R2010-6053-O(3/3)

A4(210 X 297)

Page 9

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

2012.10.18

Note :

1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface.

2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically.

CR =

3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display.

4. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100 (See FIGURE 2 shown in Appendix).

5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel.

6. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.

7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (Y shown in Appendix).

) of that same area when any adjacent area is driven dark. (See FIGURE 4

Luminance when displaying a white raster

Luminance when displaying a black raster

PAGE

OF 30

R2010-6053-O(3/3)

A4(210 X 297)

Page 10

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

5.0 INTERFACE CONNECTION.

5.1 Electrical Interface Connection

● CN1 Module Side Connector : UJU IS100-L300-C23 or Equivalent

User Side Connector : JAE FI-X30H or Equivalent

Pin No Symbol Function Remark

1 RXO0- Negative Transmission data of Pixel 0 (ODD)

2 RXO0+ Positive Transmission data of Pixel 0 (ODD)

3 RXO1- Negative Transmission data of Pixel 1 (ODD)

4 RXO1+ Positive Transmission data of Pixel 1 (ODD)

5 RXO2- Negative Transmission data of Pixel 2 (ODD)

6 RXO2+ Positive Transmission data of Pixel 2 (ODD)

7 BIST L(GND):Black, H(3.3V):Rotational Pattern

8 RXOC- Negative Transmission Clock (ODD)

9 RXOC+ Positive Transmission Clock (ODD)

10 RXO3- Negative Transmission data of Pixel 3 (ODD)

11 RXO3+ PositiveTransmission data of Pixel 3 (ODD)

12 RXE0- Negative Transmission data of Pixel 0 (EVEN)

13 RXE0+ Positive Transmission data of Pixel 0 (EVEN)

14 GND Power Ground

15 RXE1- Negative Transmission data of Pixel 1 (EVEN)

16 RXE1+ Positive Transmission data of Pixel 1 (EVEN)

17 GND Power Ground

18 RXE2- Negative Transmission data of Pixel 2 (EVEN)

19 RXE2+ Positive Transmission data of Pixel 2 (EVEN)

20 RXEC- Negative Transmission Clock (EVEN)

25 NC Not connection, this pin should be open

26 NC Not connection, this pin should be open

27 NC Not connection

28 VDD1 Power Supply:+5V

29 VDD2

30 VDD3

RXEC+ Positive Transmission Clock (EVEN)

RXE3- Negative Transmission data of Pixel 3 (EVEN)

RXE3+ Positive Transmission data of Pixel 3 (EVEN)

GND Power Ground

2012.10.18 PAGE

Note1

OF 30

Note 1： This pin should be connected with GND

R2010-6053-O(3/3)

A4(210 X 297)

Page 11

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent)

5.2.1 ODD LVDS Interface

Input

Signal

OR0

OR1

OR2

OR3

OR4

OR5

OG0

OG1

OG2

OG3

OG4

OG5

O D D

L V D

OB0

OB1

OB2

OB3

OB4

OB5

Hsync

Vsync

MCLK

OR6

OR7

OG6

OG7

OB6

OB7

RSVD

Transmitter Remark

Pin No.

48 47

46 45

42 41

40 39

38 37

System (Tx)

OUT0+

OUT1+

OUT2+

CLK OUT-

CLK OUT+

OUT3+

Interface

OUT0-

OUT1-

OUT2-

OUT3-

TFT-LCD

(Rx)

RXO0-

RXO0+

RXO1-

RXO1+

RXO2-

RXO2+

RXO CLK-

RXO CLK+

RXO3-

RXO3+

HR215WU1-120

(CN11)

Pin No.

1 2

3 4

5 6

8 9

10 11

2012.10.18 PAGE

OF 30

R2010-6053-O(3/3)

A4(210 X 297)

Page 12

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

5.2.2 EVEN LVDS Interface

Input

Signal

ER0

ER1

ER2

ER3

ER4

ER5

EG0

EG1

EG2

EG3

EG4

L V D

EG5

EB0

EB1

EB2

EB3

EB4

EB5

Hsync

Vsync

MCLK

ER6

ER7

EG6

EG7

EB6

EB7

RSVD

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

Transmitter Remark

Pin No.

48 47

46 45

42 41

40 39

38 37

System (Tx)

OUT0+

OUT1+

OUT2+

CLK OUT-

CLK OUT+

OUT3+

OUT0-

OUT1-

OUT2-

OUT3-

Interface

TFT-LCD

(Rx)

RXE0-

RXE0+

RXE1-

RXE1+

RXE2-

RXE2+

RXE CLK-

RXE CLK+

RXE3-

RXE3+

HR215WU1-120 (C

N11)

Pin No.

12 13

15 16

18 19

20 21

22 23

2012.10.18 PAGE

OF 30

R2010-6053-O(3/3)

A4(210 X 297)

Page 13

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

5.3 Data Input Format

(1,1) (2,1) (1919,1) (1920,1)

RGBRGB RGBRGB

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

1 Pixel = 3 Dots

RGB

2012.10.18 PAGE

OF 30

RGBRGB RGBRGB

(1,1080) (2,1080) (1919,1080) (1920,1080)

Display Position of Input Data (V-H)

5.4 Back-light Interface Connection

LED LightBar Connector●CN 2

Pin Function

Channel1CurrentFeedback

Channel2CurrentFeedback

LEDPowerSupply

Channel3CurrentFeedback

Channel4CurrentFeedback

:CI1406M1HRL-NH or equivalent

R2010-6053-O(3/3)

A4(210 X 297)

Page 14

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

6.0 SIGNAL TIMING SPECIFICATION

6.1 The HR215WU1-120 is operated by the DE only.

Item Symbols Min Typ Max Unit

Frequency 1/Tc 61.93 74.32 92.90 MHz

Clock

Frame Period Tv

High Time Tch - 4/7 Tc -

Low Time Tcl - 3/7 Tc -

2012.10.18

1091 1125 1149 lines

50 60 75 Hz

PAGE

OF 30

20 16.67 13.33 ms

Vertical Display Period Tvd - 1080 - lines

H-blank 100 140 240 lines

V-blank 11 45 69 lines

One line Scanning Period Th 1060 1100 1200 clocks

Horizontal Display Period Thd - 960 - clocks

Input cycle to

cycle jitter

Trcl

-100 - 100

Spresd

LVDS

Receiver

Clock

Spectrum

modulation

range

Fclkin_m

Fclkin*-3% - Fclkin*+3%

MHz

Spresd

Spectrum

modulation

Fssm

- - 300

KHz

frequency

R2010-6053-O(3/3)

A4(210 X 297)

Page 15

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

6.2 LVDS Rx Interface Timing Parameter

The specification of the LVDS Rx interface timing parameter is shown in Table 4.

Item Symbol Min Typ Max Unit Remark

CLKIN Period tRCIP

Input Data 0 tRIP1

Input Data 1 tRIP0

Input Data 2 tRIP6 2 ×tRCIP/7-0.4 2 ×tRCIP/7 2 ×tRCIP/7+0.4 nsec

Input Data 3 tRIP5 3 ×tRCIP/7-0.4 3 ×tRCIP/7 3 ×tRCIP/7+0.4 nsec

Input Data 4 tRIP4 4 ×tRCIP/7-0.4 4 ×tRCIP/7 4 ×tRCIP/7+0.4 nsec

Input Data 5 tRIP3 5 ×tRCIP/7-0.4 5 ×tRCIP/7 5 ×tRCIP/7+0.4 nsec

Input Data 6 tRIP2 6 ×tRCIP/7-0.4 6 ×tRCIP/7 6 ×tRCIP/7+0.4 nsec

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

10.76 13.46 16.15

-0.4 0.0 +0.4

tRCIP/7-0.4 tRCIP/7 tRCIP/7+0.4

nsec

2012.10.18 PAGE

OF 30

RXz +/-

* Z = 0, 1, 2,3

RxCLK+

tRIP2

tRIP3

tRIP4

tRIP5

tRIP6

tRIP0

tRIP1

Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0Rx3

tRCIP

* Vdiff = (RXz+)-(RXz-),…. ,(RXCLK+)-(RXCLK-)

Vdiff=0[v]Vdiff=0[v]

R2010-6053-O(3/3)

A4(210 X 297)

Page 16

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL

7.1 Sync Timing Waveforms

V-Sync

H-Sync

1) Need over 3 H-sync during V-Sync Low

2) Fix H-Sync width from V-Sync falling edge to first rising edge

Over 3 H-sync

Fix H-Sync width Area

2012.10.18 PAGE

OF 30

7.2 Vertical Timing W aveforms

MCLK

R7 ~ R0

G7 ~ G0

B7 ~ B0

Invalid Data DataInvalid

x,1 x,2 x,y x+1,1

Tvd

x,1050

R2010-6053-O(3/3)

A4(210 X 297)

Page 17

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

7.3 Horizontal Timing Waveforms

MCLK

RA7 ~RA0

GA7 ~GA0

BA7 ~BA0

D1 D2 Dn Data D1 D2 D3

Thd

D1048 D1049 D1050

2012.10.18 PAGE

OF 30

Invalid

MCLK

Data

Tch

Tds

Valid

Tes

2.0V

Tcl

1.5V

Tdh

Data

2.0V

0.8V

2.0V

0.8V

R2010-6053-O(3/3)

A4(210 X 297)

Page 18

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

2012.10.18 PAGE

OF 30

8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS

Color & Gray Scale

Basic Colors

Gray Scale

of RED

Gray Scale

of GREEN

Gray Scale

of BLUE

Gray Scale

of WHITE

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

Black 000000000000000000000000

Blue 000000000000000011111111

Green 000000001111111100000000

Cyan 000000001111111111111111

Red 111111110000000000000000

Magenta 111111110000000011111111

Yellow 111111111111111100000000

White 111111111111111111111111 Black 000000000000000000000000

△

Darker 000000100000000000000000

△ ▽

Brighter 111111010000000000000000

▽

Red 111111110000000000000000

Black 000000000000000000000000

△

Darker 000000000000001000000000

△ ▽

Brighter 000000001111110100000000

▽

Green 000000001111111100000000 Black 000000000000000000000000

△

Darker 000000000000000000000010

△ ▽

Brighter 000000000000000011111101

▽

Blue 000000000000000011111111

Black 000000000000000000000000

△

Darker 000000100000001000000010

△ ▽

Brighter 111111011111110111111101

▽

White 111111111111111111111111

RED DATA GREEN DATA BLUE DATA

000000010000000000000000

↑↑↑ ↓↓↓

111111100000000000000000

000000000000000100000000

↑↑↑ ↓↓↓

000000001111111000000000

000000000000000000000001

↑↑↑ ↓↓↓

000000000000000011111110

000000010000000100000001

↑↑↑ ↓↓↓

111111101111111011111110

R2010-6053-O(3/3)

A4(210 X 297)

Page 19

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

9.0 POWER SEQUENCE

To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below

Power Supply

Interface Signal

0.1VDD

0.9VDD

Valid

0.9VDD

0.1VDD

2012.10.18 PAGE

OF 30

T5 T6

Back- light

● 0.5 ms ≤ T1 ≤ 10 ms

● 0 ≤ T2 ≤ 50 ms

● 0 ≤ T3 ≤ 50 ms

● 1 sec ≤ T4

● 200 ms ≤ T5

● 200 ms ≤ T6

Notes:

1. When the power supply VDD is 0V, keep the level of input signals on the low or keep high impedance.

2. Do not keep the interface signal high impedance when power is on.

3. Back Light must be turn on after power for logic and interface signal are valid.

R2010-6053-O(3/3)

A4(210 X 297)

Page 20

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

10.0 MECHANICAL CHARACTERISTICS

10.1 Dimensional Requirements

FIGURE 6 (located in Appendix) shows mechanical outlines for the model HR215WU1-120. Other parameters are shown in Table 5.

Parameter Specification Unit

Dimensional outline

Weight

Active area

Pixel pitch

Number of pixels

495.6 ×292.2×10.7

1900(typ.)

476.64(H) × 268.11(V)

0.24825(H) x 0.24825(V)

1920(H)×1080(V) (1 pixel = R + G + B dots)

2012.10.18 PAGE

OF 30

gram

pixels

Back-light

Lower side 1-LED Light bar Type

10.2 Mounting

See FIGURE 5. (shown in Appendix)

10.3 Semi-Glare and Polarizer Hardness.

The surface of the LCD has an Anti-glare coating to reduce reflection and a coating to reduce scratching.

10.4 Light Leakage

There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 250lux.

R2010-6053-O(3/3)

A4(210 X 297)

Page 21

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

11.0 RELIABLITY TEST

The Reliability test items and its conditions are shown in below.

No Test Items

High temperature storage test

Low temperature storage test

High temperature & high humidity

operation test

High temperature operation test

Low temperature operation test

Thermal shock

Ta = 60 ℃, 240 hrs

Ta = -20 ℃, 240 hrs

Ta = 50 ℃, 80%RH, 240hrs

Ta = 50 ℃, 240hrs

Ta = 0 ℃, 240hrs

Ta = -20 ℃ ↔ 60 ℃ (0.5 hr), 100 cycle

Conditions

2012.10.18 PAGE

OF 30

Vibration test

(non-operating)

Shock test

(non-operating)

Electro-static discharge test

(non-operating)

10 Altitude test

Frequency 10 ~ 300 Hz, Sweep rate 30 min

Gravity / AMP 1.5 G

Period X, Y, Z 30 min

Gravity

Pulse width

Direction

Air : 150 pF, 330Ω, 15 KV Contact : 150 pF, 330Ω, 8 KV

50G

11msec, sine wave

± X, ± Y, ± Z Once for each

Operating: 0 to 16400ft , 0 to 40° Non Operating: 0 to 40000ft, -20 to 40°

R2010-6053-O(3/3)

A4(210 X 297)

Page 22

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

12.0 HANDLING & CAUTIONS

(1) Cautions when taking out the module

y Pick the pouch only, when taking out module from a shipping package.

(2) Cautions for handling the module

y As the electrostatic discharges may break the LCD module, handle the LCD

module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible.

y As the LCD panel and back - light element are made from fragile glass material,

impulse and pressure to the LCD module should be avoided.

y As the surface of the polarizer is very soft and easily scratched, use a soft dry

cloth without chemicals for cleaning.

y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care.

(3) Cautions for the operation

y When the module is operating, do not lose CLK, ENAB signals. If any one of

these signals is lost, the LCD panel would be damaged.

y Obey the supply voltage sequence. If wrong sequence is applied, the module

would be damaged.

(4) Cautions for the atmosphere

y Dew drop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or

humidity atmosphere. Storage in an electro-conductive polymer packing pouch

and under relatively low temperature atmosphere is recommended.

(5) Cautions for the module characteristics

y Do not apply fixed pattern data signal to the LCD module at product aging. y Applying fixed pattern for a long time may cause image sticking.

(6) Other cautions

y Do not disassemble and/or re-assemble LCD module. y Do not re-adjust variable resistor or switch etc. yWhen returning the module for repair or etc., Please pack the module not to be

broken. We recommend to use the original shipping packages.

2012.10.18 PAGE

OF 30

R2010-6053-O(3/3)

A4(210 X 297)

Page 23

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

13.0 PRODUCT SERIAL NUMBER

HR215WU1-120

2012.10.18 PAGE

OF 30

1 2 3 4 5 6 7

XX X X XX X XXXX XXXXXX

1. Control Number

2. Rank / Grade

3. Line Classification

4. Year (2001 : 01, 2002 : 02, …)

5. Month (1,2,3, … , 9, X, Y, Z)

6. Internal Use

7. Serial Number

R2010-6053-O(3/3)

A4(210 X 297)

Page 24

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

14.0 Packing

14.1 Packing Order

PutEPECushionintothebox

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

Asshowninthefigure,placethe modulesbundledbypackingbag Inthebox

2012.10.18 PAGE

OF 30

Aftersealingthebox,attachPacking Labelontheattachpositionsignarea ofthebox.

R2010-6053-O(3/3)

PlaceEPEcoverontopofthebox

A4(210 X 297)

Page 25

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

14.2 Pallet Packing Order

Load Pallet in correct position

Box cover

PRODUCT SPEC-TFT MODULE

Pile up the unit Box filled with Modules on the Pallet carefully not to make a space.

Polyester bend

2012.10.18 PAGE

OF 30

Adjust Outer box to piling Boxes and cover the Outer box using box cover. Bend Pallet Assy which is putting the Box Cover tight in two direction (horizontal and vertical) and two times using Polyester bend.

R2010-6053-O(3/3)

Out box

Wrap the Pallet Assy loaded 1story, 2stories from downside through side and to edge of upside. (12Boxes/Pallet)

A4(210 X 297)

Page 26

PRODUCT GROUP

REV

ISSUE DATE

PRODUCT SPEC-TFT MODULE

SPEC. NUMBER

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

14.3 Packing Specification and Note

Item

Panel 1

Cushion 1 - 0.70 -

Box 1 558(L)mm x 348(W)mm x 400(H)mm 0.70 without Panel & cushion

Packing Box

Pallet 1

Pallet after Packing

Q'ty Dimension Weight (kg)

495.6(H) × 292.2(V) × 10.7(D) typ.

10pcs/Bo

12boxes/

pallet

558(L)mm x 348W)mm x 400(H)mm 20.4 with panel & cushion

1200(L)mm x 1140(W)mm x 120(H)m

1140(L)mm x 1076W)mm x 820(H)mm 264 -

14.3 Box label

y Label Size : 108 mm (L) × 56 mm (W) y Contents

Model : HR215WU1-120 Q`ty : Module Q`ty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product

Specification

1.9 -

15.90 -

2012.10.18

Remark

PAGE

OF 30

00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no

R2010-6053-O(3/3)

HR215WU1-120

0000000000000

3930

201X.X.XX

FG CODE

RoHS Mark

A4(210 X 297)

Page 27

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

15.0 APPENDIX

Figure 1. Measurement Set Up

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

(L = 50cm )

2012.10.18 PAGE

OF 30

Figure 2. White Luminance and Uniformity Measurement Locations (9 points)

R2010-6053-O(3/3)

192 960 1728

108

540

972

A4(210 X 297)

Page 28

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

Display data

Optical Response

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

Figure 3. Response Time Testing

White(TFT OFF)

100%

90%

10%

Black(TFT ON)

White(TFT OFF)

Time

2012.10.18 PAGE

OF 30

Figure 4. Cross Modulation Test Description

VIEW AREA VIEW AREA

(D/4, W/4)

L31

(3D/4, 3W/4)

(D, W)

YA(7D/8,W/2)

(D, W)

Cross-Talk (%) =

YB-Y

× 100

Where: YA= Initial luminance of measured area (cd/m2)

= Subsequent luminance of measured area (cd/m2)

The location measured will be exactly the same in both patterns

YB(7D/8,W/2)

R2010-6053-O(3/3)

A4(210 X 297)

Page 29

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

Figure 5. TFT-LCD Module Outline Dimensions (Front view)

2012.10.18 PAGE

OF 30

( )



R2010-6053-O(3/3)

A4(210 X 297)

Page 30

PRODUCT GROUP

REV

ISSUE DATE

SPEC. NUMBER

PRODUCT SPEC-TFT MODULE

SPEC. TITLE B3 HR215WU1-120 Product Specification_ Rev.O

Figure 6. TFT-LCD Module Outline Dimensions (Rear view)

2012.10.18 PAGE

OF 30

R2010-6053-O(3/3)

A4(210 X 297)