BOE HR215WU1-100 Specification
PROPRIETARY NOTE
TFT MODULE
THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HF AND
MUST BE RETURNED TO BOE HF UPON ITS REQUEST
SPEC. NUMBER
PRODUCT GROUP
Rev. 0
ISSUE DATE
2012.03.05
TITLE : B3 HR215WU1-100
Product Specification
Rev. 0
PAGEPAGE
OF30
1
R2010-6053-O(1/3)
HEFEI BOE OPTOELECTRONICS TECHNOLOGY
A4(210 X 297) A4(210 X 297)
PRODUCT GROUP
PRODUCT SPEC-TFT MODULE 0 2012.03.05
REV
ISSUE DATE
SPEC. NUMBER
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
PAGE
2
OF 30
REVISION HISTORY
REV. ECN No. DESCRIPTION OF CHANGES DATE PREPARED
0 Initial Release 2012.03.05 Hengzhen Liang
R2010-6053-O(2/3)
A4(210 X 297)
PRODUCT GROUP
2.0
Absolute Maximum Ratings
6
REV
ISSUE DATE
SPEC. NUMBER
No. Item Page
1.0 General Description 4
3.0 Electrical Specifications 7
4.0 Optical Specifications 8
5.0 Interface Connection 10
6.0 Signal Timing Specifications 13
7.0 Signal Timing Waveforms of Interface Signal 15
8.0 Input Signals, Display Colors & Gray Scale of Colors 17
PRODUCT SPEC-TFT MODULE
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
Contents
0
2012.03.05
PAGE
OF 30
3
9.0 Power Sequence 18
10.0 Mechanical Characteristics 19
11.0 Reliability Test 20
12.0 Handling& Cautions 21
13.0 Product Serial Number 22
14.0 Packing 23
15.0 Appendix 25
R2010-6053-O(3/3)
A4(210 X 297)
PRODUCT GROUP
e
e
e
e
Incorporated edge type back
light (
One Light Bar
)
REV
ISSUE DATE
SPEC. NUMBER
PRODUCT SPEC-TFT MODULE
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
0
1.0 GENERAL DESCRIPTION
1.1 Introduction
HR215WU1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 21.5 inch
diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this
module is adapted for a low reflection and higher color type.
Conn
ctor (CN
LVDS
Input
Signal
LVDS Rx
+
T/CON
+
Mini LVDS Tx
Gat
Driver
Source Driver
TFT LCD Panel
2012.03.05
PAGE
OF 30
4
1920 × 1080
VDD
1
)
1.2 Features
z LVDS Interface with 2 pixel / clock
z High-speed response
z 6-bit (Hi-FRC) color depth, display 16. 7M colors
z
z High luminance and contrast ratio, low reflection and wide viewing angle
z DE (Data Enable) only
z RoHS /TCO 5.0 ,ES5.0 Compliant
R2010-6053-O(3/3)
DC/DC
Gamma
Vcom
LED Light Bar
-
CN2
A4(210 X 297)
PRODUCT GROUP
p
REV
ISSUE DATE
PRODUCT SPEC-TFT MODULE
SPEC. NUMBER
1.3 Application
z Desktop Type of PC & Workstation Use
z Slim-Size Display for Stand-alone Monitor
z Display Terminals for Control System
z Monitors for Process Controller
1.4 General Specification
The followings are general specifications at the model HR215WU1-100.
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
0
2012.03.05
PAGE
OF 30
5
<Table 1. General Specifications>
Parameter Specification Unit
Active area
Number of pixels
Pixel pitch
Pixel arrangement RGB Vertical stripe -
Display colors 16.7M colors
Display mode Normally Black -
Dimensional outline
Weight 1900 (typ.) g
Surface Treatment
Back-light
476.64(H) × 268.11 (V)
1920(H) ×1080(V)
0.24825(H) ×0.24825(V)
495.6(H) × 292.2(V) × 10.2(D) typ.
Anti-glare, 3H
Lower side 1-LED Light bar Type
mm
pixels
mm
mm
-
-
Remarks
R2010-6053-O(3/3)
A4(210 X 297)
PRODUCT GROUP
< Table 2. Absolute Maximum Ratings>
[VSS GND 0V]
Wet bulb temperature should be 39
C
max. and no condensation of water
5
REV
ISSUE DATE
PRODUCT SPEC-TFT MODULE
SPEC. NUMBER
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
Symbol Min. Max. Unit Remarks
Parameter
Power Supply Voltage V
Logic Supply Voltage V
Operating Temperature T
Storage Temperature T
DD
IN
OP
ST
-0.5 5.5
VSS-0.3 VDD+0.3 V
0+50
-20 +60
℃
℃
0
2012.03.05
PAGE
OF 30
6
=
=
V
Ta = 25 ℃
1)
1)
Note : 1) Temperature and relative humidity range are shown in the figure below.
O
100
80
ity (%RH)
Relative Humid
60
40
20
90
O perating R ange
Storage Range
0
20 40 60 80-20
Tem perature (˚C)
(39,90)
(50,50)
(60,30)
.
R2010-6053-O(3/3)
A4(210 X 297)
PRODUCT GROUP
Diff
|
VID|
200-600mV
REV
ISSUE DATE
PRODUCT SPEC-TFT MODULE
SPEC. NUMBER
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
3.0 ELECTRICAL SPECIFICATIONS
3.1Electrical Specifications
< Table 3. Electrical specifications >
Parameter Min. Typ. Max. Unit Remarks
Power Supply Voltage V
Power Supply Current I
In-Rush Current I
Permissible Input Ripple Voltage V
High Level Differential Input
Threshold Voltage
Low Level Differential Input
Threshold Voltage
erential input voltage
Differential input common mode voltage Vcm 1.0 1.2 1.5
DD
DD
RUSH
RF
V
IH
V
IL
4.5 5.0 5.5 V
- 800 1400 mA
--3ANote 2
- - 100 mV VDD= 5.0V
- - +100 mV
-100 - - mV
0
2012.03.05
[Ta =25±2 ℃]
Note1
VIH=100mV,
VIL=-100mV
PAGE
OF 30
7
LED Voltage V
LED Channel Voltage V
LED Channel Current I
LED Lifetime 30,000 - - Hrs IL=120 mA
Power Consumption
L
L
L
P
D
P
BL
P
total
3.05
39.65
- 120 160 mA
-4.9-W
- 19.97 - W I
- 24.87 - W
3.2
41.6
3.5 V
45 V
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz. Test Pattern of power
supply current
a) Typ : Color Bar pattern
b) Max : Skip Sub Pixel Pattern
2. Duration of rush current is about 2 ms and rising time of VDD is 520 μs ± 20 %
3. The lamp frequency should be selected as different as possible from the horizontal
synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display
4. Calculated value for reference (V
× IL) ×4(channel) excluding driver loss. (LED Light bar: 13S4P)
L
=120 mA, Note 4
L
R2010-6053-O(3/3)
A4(210 X 297)
PRODUCT GROUP
the 9 o’clock direction (“left”) and θ
(= θ
) as the 6 o’clock direction (“bottom”). W
sca
d/or Ø, the
t e 9 o c oc d ect o ( e t ) a d θ
Ø=270
( θ
6
) as t e 6 o c oc d ect o ( botto ). W e sca g θ ad/oØ,te
Θ
89-D
W
0.299
0.329
0.359
(C
)
Wy0. 99
0.3 9
0.359
REV
ISSUE DATE
SPEC. NUMBER
PRODUCT SPEC-TFT MODULE
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
0
2012.03.05
PAGE
8
OF 30
4.0 OPTICAL SPECIFICAT ION
4.1 Overview
The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature =
25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall
be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to
θ
(=θ3) as the 3 o’clock direction (the “right”), θ
Ø=0
center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30
minutes warm-up period. VDD shall be 5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock.
4.2 Optical Specifications
[VDD = 5.0V, Frame rate = 60Hz, Clock = 78MHz, IBL= 120mA, Ta =25±2 ℃]
Parameter Symbol Condition Min. Typ. Max. Unit Remark
Θ
Horizontal
Viewing Angle range
Vertical
Horizontal
Viewing Angle range
Vertical
Luminance Contrast ratio CR
Luminance of White Y
White luminance uniformity ΔY7580%Note 4
White
Red
Reproduction
of color
Green
Blue
Response
Time
Cross Talk CT - - 2.0 % Note 7
Rising+Fal
ling
3
Θ
9
Θ
12
Θ
6
Θ
3
Θ
9
12
Θ
6
w
W
x
R
x
R
y
G
x
G
y
B
x
B
y
T
T
r
f
+
(= θ12) as the 12 o’clock direction (“upward”), θ
Ø=90
hile
-89-Deg.
CR > 10
CR > 5
Θ = 0°
enter
Normal
Viewing
Angle
-89-Deg.
-89-Deg.
-89-Deg.
-89-Deg.
-89-Deg.
-
-89-Deg.
700 1000 - Note 2
200 250 - cd/m
0.283 0.313 0.343
0.617 0.647 0.677
0.309 0.339 0.369
0.277 0.307 0.337
0.603 0.633 0.663
0.116 0.146 0.176
0.026 0.056 0.086
14 ms Note 6
nning θ an
eg.
2
Ø=180
(= θ9) as
Note 1
Note 3
Note 5
R2010-6053-O(3/3)
A4(210 X 297)
PRODUCT GROUP
di
ith
LCD
Luminance when displaying a black raster
(See FIGURE 2 shown in Appendix)
7.
Cross
Talk of one area of the LCD surface by another shall be measured by comparing the
REV
ISSUE DATE
SPEC. NUMBER
PRODUCT SPEC-TFT MODULE
SPEC. TITLE
B3 HR215WU1-100 Product Specification_ Rev.0
0
2012.03.05
9
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
rection w
2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD
surface. Luminance shall be measured with all pixels in the view field set first to white, then
to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR)
is defined mathematically.
3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with
all pixels in the view field set first to white. This measurement shall be taken at the locations
shown in FIGURE 2 for a total of the measurements per display.
4. The White luminance uniformity on LCD surface is then expressed as :
ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100
5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral
data measured with all pixels first in red, green, blue and white. Measurements shall be made
at the center of the panel.
6. The electro-optical response time measurements shall be made as FIGURE 3 shown in
Appendix by switching the “data” input signal ON and OFF. The times needed for the
luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.
luminance (Y
luminance (Y
shown in Appendix).
respect to the optical axis which is normal to the
CR =
Luminance when displaying a white raster
surface.
.
) of a 25mm diameter area, with all display pixels set to a gray level, to the
A
) of that same area when any adjacent area is driven dark. (See FIGURE 4
B
PAGE
OF 30
R2010-6053-O(3/3)
A4(210 X 297)
Loading...