THIS SPECIFICATION IS THE PROPERTY OF BOE DT AND SHALL NOT BE
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE DT AND
MUST BE RETURNED TO BOE DT UPON ITS REQUEST
TITLE : HM236WU1-100
www.panelook.com
PROPRIETARY NOTE
Product Specification
Rev.P1
BEIJING BOE Display TECHNOLOGY
SPEC. NUMBER
z
B2010-8002-O (1/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PRODUCT GROUP
TFT-LCD
Rev.P1
ISSUE DATE
2011.8.8
PAGE
PAGE
X
OF 28
A4(210 X 297)
A4(210 X 297)
www.panelook.com
Page 2
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCTRev.P1Aug. 8. 11’
REV
ISSUE DATE
REVISION HISTORY
REV.ECN No.DESCRIPTION OF CHANGES DATE PREPARED
Rev.P0Initial ReleaseJuly. 20. 11 ’Zheng Xiaopan
Rev.P12
nd
ReleaseAug.8. 11’Zheng Xiaopan
SPEC. NUMBER
z
B2010-8002-O (2/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
Y
OF 28
A4(210 X 297)
www.panelook.com
Page 3
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
Contents
No.ItemPage
1.0General Description4
2.0Absolute Maximum Ratings6
3.0Electrical Specifications7
4.0Optical Specifications8
5.0Interface Connection10
6.0Signal Timing Specifications13
7.0Signal Timing Waveforms of Interface Signal15
8.0Input Signals, Display Colors & Gray Scale of Colors17
9.0Power Sequence18
10.0Mechanical Characteristics19
11.0Reliability Test20
12.0Handling& Cautions 21
13.0Product Serial Number22
14.0Packing23
15.0Appendix25
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
Z
OF 28
A4(210 X 297)
www.panelook.com
Page 4
Global LCD Panel Exchange Center
Ý
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
1.0 GENERAL DESCRIPTION
1.1 Introduction
HM236WU1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 23.6 inch
diagonally measured active area with FHD resolutions (1920 horizontal by 1080 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical stripe and this module can display 16.7M colors. The TFT-LCD panel used for this
module is adapted for a low reflection and higher color type.
LVDS
Input
Signal
Connector (CN
LVDS Rx
+
T/CON
+
Mini LVDS Tx
Gate Driver
Source Driver
TFT LCD Panel
ISSUE DATE
Aug. 8. 11’
1920
VDD
1
)
1.2 Features
z LVDS Interface with 2 pixel / clock
z High-speed response
z 6-bit (Hi-FRC) color depth, display 16. 7M colors
z Incorporated edge type back-light (LED)
z High luminance and contrast ratio, low reflection and wide viewing angle
z DE (Data Enable) only
z RoHS/Halogen Free
z TCO 5.0 , E/S 5.0 compliant
z Gamma Correction
DC/DC
Gamma
Vcom
LED Lighting Bar
1080
LED Connector
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
[
OF 28
A4(210 X 297)
www.panelook.com
Page 5
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
1.3 Application
z Desktop Type of PC & Workstation Use
z Slim-Size Display for Stand-alone Monitor
z Display Terminals for Control System
z Monitors for Process Controller
1.4 General Specification
The followings are general specifications at the model HM236WU1-100.
<Table 1. General Specifications>
ParameterSpecificationUnit
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
Remarks
Active area
Number of pixels
Pixel pitch
521.28(H) Ý 293.22(V)
1920(H) ശ1080(V)
0.2715(H) ശ0.2715(V)
mm
pixels
mm
Pixel arrangementRGB Vertical stripe
Display colors16.7Mcolors
Display modeNormally White
Dimensional outline
544.8(H) Ý 320.5(V) Ý 9.6(D) typ.
mm
Weight 2200 (Typ.)g
Surface Treatment
Haze 25%, 3H
Back-lightLower edge side, 1-LED Lighting Bar typeNote 1
P
: T.B.D (max)
D
Power Consumption
P
: 14.9W (max)Note 2
BL
: T.B.D (max)
P
total
Notes : 1. LED Lighting Bar (4*input pins)
2. P
LED=Input pins* VPINÝIPIN
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
\
OF 28
A4(210 X 297)
www.panelook.com
Page 6
Global LCD Panel Exchange Center
ڋ
ڍ ڋ
ڏ ڋ
ڑ ڋ
ړ ڋ
ڈڍ ڋ
ڐ
ڍ ڋ
ڏ ڋ
ڑ ڋ
ړ ڋ
ڔڋ
ڌ ڋ ڋ
ڪ ۋ ۀ ۍڼ ۏۄۉ ۂ ٻڭ ڼ ۉ ۂ ۀ
ڮ ۏۊ ۍڼ ۂ ۀ ٻڭ ڼ ۉ ۂ ۀ
ڭۀ ۇ ڼۏ ۄۑ ۀٻڣ ې ۈۄ ڿۄ ۏ۔ ٻڃ ڀڭ ڣڣڄ
گ ۀ ۈ ۋ ۀ ۍڼ ۏې ۍۀ ٻڃഴڞ ڄ
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. Absolute Maximum Ratings>
SymbolMin.Max.UnitRemarks
Parameter
Power Supply VoltageV
Logic Supply VoltageV
LED Light Bar Current
Per Input Pin
LED Light Bar Voltage
Per Input Pin
IPINT.B.DT.B.DmA
VPINT.B.DT.B.DV
DD
IN
-0.36.0
VSS-0.3VDD+0.3V
[VSS=GND=0V]
V
ISSUE DATE
Aug. 8. 11’
Ta = 25 ć
Operating TemperatureT
Storage TemperatureT
OP
ST
0+50
-20+60
ć
ć
Note : 1) Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 OC max. and no condensation of water.
OZ`S`WP
O\WS\WP
O]WSZWP
1)
1)
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
]
OF 28
A4(210 X 297)
www.panelook.com
Page 7
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
3.0 ELECTRICAL SPECIFICATIONS
3.1Electrical Specifications
< Table 3. Electrical specifications >
ParameterMin.Typ.Max.UnitRemarks
Power Supply VoltageV
Power Supply CurrentI
In-Rush CurrentI
Permissible Input Ripple VoltageV
High Level Differential Input
Threshold Voltage
Low Level Differential Input
Threshold Voltage
Differential input voltage|V
Differential input common mode voltageVcm1.01.21.5
DD
DD
RUSH
RF
V
IH
V
IL
|200-600mV
ID
4.55.05.5V
-T.B.DT.B.DmA
-2.03.0ANote 2
--100mVVDD= 5.0V
--+100mV
-100--mV
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
[Ta =25ധ2 ć]
Note1
V
=100mV,
IH
VIL=-100mV
-T.B.DT.B.DW
13.214.114.9WNote 3
-W
Power Consumption
P
D
P
BL
P
total
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz
Clock frequency = 92.9 MHz. Test Pattern of power supply current
a) Typ : T.B.D
b) Max : T.B.D
2. Duration of rush current is about 2 ms and rising time of VDD is 520 μs ρ 20 %
3. Calculated value for reference (Input pins*VPIN ശIPIN) excluding inverter loss.
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
^
OF 28
A4(210 X 297)
www.panelook.com
Page 8
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
3.2 Backlight Unit
< Table 4. LED Backlight Unit >
ParameterMin.Typ.Max.UnitRemarks
LED Light Bar Input Voltage Per
Input Pin
LED Light Bar Input Current Per
Input Pin
LED Power ConsumptionP
LED Life-Time-30,000-HrsNote 4
VPIN3335.237.4VDuty 100%
IPIN-100-mANote1,2,
BL
13.214.114.9WNote 3
Note1: There are one light bar ,and the specified current is input LED chip 100% duty current
Note2: The sense current of each input pin is 100mA
Note3: P
BL=4 Input pins*VPIN ശIPIN
Note4: The lifetime is determined as the time at which luminance of LED become 50% of the initial
brightness or not normal lighting at IPIN=100mA on condition of continuous operating at
25 ധ2 ć
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
_
OF 28
A4(210 X 297)
www.panelook.com
Page 9
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
4.0 OPTICAL SPECIFICATION
4.1 Overview
The test of Optical specifications shall be measured in a dark room (ambient luminance d 1 lux and temperature =
25r2ć) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall
be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0q. We refer to
(=θ3) as the 3 o’clock direction (the “right”), θ
θ
Ø=0
the 9 o’clock direction (“left”) and θ
(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the
Ø=270
center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30
minutes warm-up period. VDD shall be 5.0V +/-10% at 25qC. Optimum viewing angle direction is 6 ’clock.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
`
OF 28
A4(210 X 297)
www.panelook.com
Page 10
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
Note :
1.Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are
determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock
direction with respect to the optical axis which is normal to the LCD surface.
2.Contrast measurements shall be made at viewing angle of T= 0q and at the center of the LCD
surface. Luminance shall be measured with all pixels in the view field set first to white, then
to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR)
is defined mathematically.
CR =
3.Center Luminance of white is defined as the LCD surface. Luminance shall be measured with
all pixels in the view field set first to white. This measurement shall be taken at the locations
shown in FIGURE 2 for a total of the measurements per display.
4.The White luminance uniformity on LCD surface is then expressed as :
ԩY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100
(See FIGURE 2 shown in Appendix).
5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral
data measured with all pixels first in red, green, blue and white. Measurements shall be made
at the center of the panel.
6. The electro-optical response time measurements shall be made as FIGURE 3 shown in
Appendix by switching the “data” input signal ON and OFF. The times needed for the
luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.
7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the
luminance (Y
luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4
shown in Appendix).
) of a 25mm diameter area, with all display pixels set to a gray level, to the
A
Luminance when displaying a white raster
Luminance when displaying a black raster
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
XW
OF 28
A4(210 X 297)
www.panelook.com
Page 11
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
5.0INTERFACE CONNECTION.
5.1 Electrical Interface Connection
5.1.1 LED Light Bar
< Table 1. LED Light Bar>
Pin No SymbolDescription
1IRLED1LED current sense for string1
2IRLED2LED current sense for string2
3VLEDLED power supply
4VLEDLED power supply
5IRLED3LED current sense for string3
6IRLED4LED current sense for string4
7CONNECTOR3708K-Q06N-00R
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
SPEC. NUMBER
S
B2010-8002-O (3/3)
Figure1. Top View of LED Bar Connector
Figure2. Back Side of Module
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
XX
OF 28
A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 12
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
5.0INTERFACE CONNECTION.
5.1 Electrical Interface Connection
CN11 Module Side Connector : UJU IS100-L30R-C23or Equivalent
User Side Connector : JAE FI-X30H or Equivalent
Pin NoSymbolFunctionRemark
1RXO0-Negative Transmission data of Pixel 0 (ODD)
2RXO0+Positive Transmission data of Pixel 0 (ODD)
3RXO1-Negative Transmission data of Pixel 1 (ODD)
4RXO1+Positive Transmission data of Pixel 1 (ODD)
5RXO2-Negative Transmission data of Pixel 2 (ODD)
6RXO2+Positive Transmission data of Pixel 2 (ODD)
7GNDPower Ground
8RXOC-Negative Transmission Clock (ODD)
9RXOC+Positive Transmission Clock (ODD)
10RXO3-Negative Transmission data of Pixel 3 (ODD)
11RXO3+Positive Transmission data of Pixel 3 (ODD)
12RXE0-Negative Transmission data of Pixel 0 (EVEN)
13RXE0+Positive Transmission data of Pixel 0 (EVEN)
14GNDPower Ground
15RXE1-Negative Transmission data of Pixel 1 (EVEN)
16RXE1+Positive Transmission data of Pixel 1 (EVEN)
17GNGPower Ground
18RXE2-Negative Transmission data of Pixel 2 (EVEN)
19RXE2+Positive Transmission data of Pixel 2 (EVEN)
20RXEC-Negative Transmission Clock (EVEN)
21RXEC+Positive Transmission Clock (EVEN)
22RXE3-Negative Transmission data of Pixel 3 (EVEN)
23RXE3+Positive Transmission data of Pixel 3 (EVEN)
24GNDPower GroundNote 1
25NC
26NC
27NC
28VDD
30VDD
No. Connection
Power Supply: +5V29VDD
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
Note 1 : This pin should be connected with GND.
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
XY
OF 28
A4(210 X 297)
www.panelook.com
Page 13
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent)
5.2.1 LVDS Interface
OUT0-
OUT1-
OUT2-
OUT3-
Interface
TFT-LCD
(Rx)
RXO0-
RXO0+
RXO1-
RXO1+
RXO2-
RXO2+
RXO CLK-
RXO CLK+
RXO3-
RXO3+
Input
Signal
OR0
OR1
OR2
OR3
OR4
OR5
OG0
OG1
OG2
OG3
OG4
OG5
OB0
L
V
D
S
OB1
OB2
OB3
OB4
OB5
Hsync
Vsync
DE
MCLK
OR6
OR7
OG6
OG7
OB6
OB7
RSVD
TransmitterRemark
Pin No.
51
52
54
55
56
3
4
6
7
11
12
14
15
19
20
22
23
24
27
28
30
31
50
2
8
10
16
18
25
Pin No.
48
47
46
45
42
41
40
39
38
37
System (Tx)
OUT0+
OUT1+
OUT2+
CLK OUT-
CLK OUT+
OUT3+
REV
Rev.P1
HT236F01-100
(CN11)
Pin No.
1
2
3
4
5
6
8
9
10
11
ISSUE DATE
Aug. 8. 11’
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
XZ
OF 28
A4(210 X 297)
www.panelook.com
Page 14
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
5.3 Data Input Format
OXSXPOYSXPOX`X`SXPOX`YWSXP
yniyniyniyni
XGwGdGZGk
yni
ISSUE DATE
Aug. 8. 11’
yniyniyniyni
OXSXW_WP OYSXW_WPOX`X`SXW_WP OX`YWSXW_WP
Display Position of Input Data (V-H)
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
X[
OF 28
A4(210 X 297)
www.panelook.com
Page 15
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
6.0 SIGNAL TIMING SPECIFICATION
6.1 The HM236WU1-100 is operated by the DE only.
ItemSymbolsMinTypMaxUnit
Frequency1/Tc58.5474.2598MHz
Clock
Frame PeriodTv
Vertical Display PeriodTvd-1080-lines
High TimeTch-4/7Tc-
Low TimeTcl-4/7Tc-
REV
Rev.P1
111511261136lines
506075Hz
2016.713.3ms
ISSUE DATE
Aug. 8. 11’
One line Scanning PeriodTh105011001150clocks
Horizontal Display PeriodThd960960960clocks
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
X\
OF 28
A4(210 X 297)
www.panelook.com
Page 16
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
6.2 LVDS Rx Interface Timing Parameter
The specification of the LVDS Rx interface timing parameter is shown in Table 4.
<Table 4. LVDS Rx Interface Timing Specification>
ItemSymbolMinTypMaxUnitRemark
CLKIN PeriodtRCIP10.2013.4717.08nsec
Input Data 0tRIP1-0.40.0+0.4nsec
Input Data 1tRIP0tRCIP/7-0.4tRCIP/7tRCIP/7+0.4nsec
Input Data 2tRIP62 ശtRCIP/7-0.42 ശtRCIP/72 ശtRCIP/7+0.4nsec
Input Data 3tRIP53 ശtRCIP/7-0.43 ശtRCIP/73 ശtRCIP/7+0.4nsec
Input Data 4tRIP44 ശtRCIP/7-0.44 ശtRCIP/74 ശtRCIP/7+0.4nsec
Input Data 5tRIP35 ശtRCIP/7-0.45 ശtRCIP/75 ശtRCIP/7+0.4nsec
Input Data 6tRIP26 ശtRCIP/7-0.46 ശtRCIP/76 ശtRCIP/7+0.4nsec
ISSUE DATE
Aug. 8. 11’
RXz +/-
* Z = 0, 1, 2,3
RxCLK+
tRIP2
tRIP3
tRIP4
tRIP5
tRIP6
tRIP0
tRIP1
Rx2Rx1Rx0Rx6Rx5Rx4Rx3Rx2Rx1Rx0Rx3
tRCIP
* Vdiff = (RXz+)-(RXz-),…. ,(RXCLK+)-(RXCLK-)
Vdiff=0[v]Vdiff=0[v]
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
X]
OF 28
A4(210 X 297)
www.panelook.com
Page 17
Global LCD Panel Exchange Center
MCLK
DE
x,1x,2x,yx+1,1
x,1050
Invalid Data
Data
Invalid
Th
Tv
Tvd
R7 ~ R0
G7 ~ G0
B7 ~ B0
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL
7.1 Sync Timing Waveforms
}Tz
oTz
kl
1) Need over 3 H-sync during V-Sync Low
2) Fix H-Sync width from V-Sync falling edge to first rising edge
v Z oT
m oTz h
ISSUE DATE
Aug. 8. 11’
7.2 Vertical Timing Waveforms
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
X^
OF 28
A4(210 X 297)
www.panelook.com
Page 18
Global LCD Panel Exchange Center
Invalid
D1048
D1049
D1050
Th
Thd
Tc
RA7 ~RA0
GA7 ~GA0
BA7 ~BA0
Tch
Tcl
Tdh
Tds
2.0V
0.8V
2.0V
0.8V
Tes
2.0V
MCLK
Va lid
Data
Data
DE
1.5V
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
7.3 Horizontal Timing Waveforms
MCLK
DE
D1D2DnDataD1D2D3
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
X`
OF 28
A4(210 X 297)
www.panelook.com
Page 20
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
9.0 POWER SEQUENCE
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
shall be as shown in below
w z
p z
WU`}kk
WUX}kk
W}
{X
{Y
}
W}
WU`}kk
{Z
WUX}kk
{[
ISSUE DATE
Aug. 8. 11’
{\{]
iT
W}
0.5 ms ≤ T1 d 10 ms
0 d T2 d50 ms
0 ≤ T3 d50 ms
1 sec d T4
200 ms d T5
200 ms d T6
Notes:
1. When the power supply VDD is 0V, keep the level of input signals on
the low or keep high impedance.
2. Do not keep the interface signal high impedance when power is on.
3. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
YW
OF 28
A4(210 X 297)
www.panelook.com
Page 21
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
10.0 MECHANICAL CHARACTERISTICS
10.1 Dimensional Requirements
FIGURE 6 (located in Appendix) shows mechanical outlines for the model HM236WU1-100.
Other parameters are shown in Table 5.
<Table 5. Dimensional Parameters>
ParameterSpecificationUnit
Dimensional outline
Weight
Active area
Pixel pitch
Number of pixels
544.8(H) Ý 320.5(V) Ý 9.6(D) typ
2200(typ)
521.28 (H) Ý 293.22 (V)
0.2715 (H) ശ0.2715 (V)
1920 (H)ശ1080 (V) (1 pixel = R + G + B dots)
ISSUE DATE
Aug. 8. 11’
mm
gram
mm
mm
pixels
Back-light
Lower edge side, 1-LED Lighting Bar type
10.2 Mounting
See FIGURE 5. (shown in Appendix)
10.3 Anti-Glare and Polarizer Hardness.
The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce
scratching.
10.4 Light Leakage
There shall not be visible light from the back-lighting system around the edges of the screen as
seen from a distance 50cm from the screen with an overhead light level of 350lux.
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
YX
OF 28
A4(210 X 297)
www.panelook.com
Page 22
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
11.0 RELIABLITY TEST
The Reliability test items and its conditions are shown in below.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
YY
OF 28
A4(210 X 297)
www.panelook.com
Page 23
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
12.0 HANDLING & CAUTIONS
(1) Cautions when taking out the module
y Pick the pouch only, when taking out module from a shipping package.
(2) Cautions for handling the module
y As the electrostatic discharges may break the LCD module, handle the LCD
module with care. Peel a protection sheet off from the LCD panel surface as
slowly as possible.
y As the LCD panel and back - light element are made from fragile glass material,
impulse and pressure to the LCD module should be avoided.
y As the surface of the polarizer is very soft and easily scratched, use a soft dry
cloth without chemicals for cleaning.
y Do not pull the interface connector in or out while the LCD module is operating.
y Put the module display side down on a flat horizontal plane.
y Handle connectors and cables with care.
(3) Cautions for the operation
y When the module is operating, do not lose CLK, ENAB signals. If any one of
these signals is lost, the LCD panel would be damaged.
y Obey the supply voltage sequence. If wrong sequence is applied, the module
would be damaged.
(4) Cautions for the atmosphere
y Dew drop atmosphere should be avoided.
y Do not store and/or operate the LCD module in a high temperature and/or
humidity atmosphere. Storage in an electro-conductive polymer packing pouch
and under relatively low temperature atmosphere is recommended.
(5) Cautions for the module characteristics
y Do not apply fixed pattern data signal to the LCD module at product aging.
y Applying fixed pattern for a long time may cause image sticking.
(6) Other cautions
y Do not disassemble and/or re-assemble LCD module.
y Do not re-adjust variable resistor or switch etc.
yWhen returning the module for repair or etc., Please pack the module not to be
broken. We recommend to use the original shipping packages.
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
YZ
OF 28
A4(210 X 297)
www.panelook.com
Page 24
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
13.0 PRODUCT SERIAL NUMBER
REV
Rev.P1
otYZ]~|XTXWW
ISSUE DATE
Aug. 8. 11’
1 2 3 4 5 6 7
XXXXXXXXXXXXXXXXX
1. Control Number
2. Rank / Grade
3. Line Classification
4. Year (2001 : 01, 2002 : 02, …)
5. Month (1,2,3, … , 9, X, Y, Z)
6. Internal Use
7. Serial Number
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
Y[
OF 28
A4(210 X 297)
www.panelook.com
Page 25
Global LCD Panel Exchange Center
www.panelook.com
14.0 Packing
14.1 Packing Order
Put pad into the box
PRODUCT GROUP
TFT- LCD PRODUCT
As shown in the figure, place
the modules bundled by
packing bag in the box
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
After sealing the box, attach
packing label on the attach
position sign area of the box
SPEC. NUMBER
S
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
Place a cover on the top of
the box
PAGE
Y\
OF 28
A4(210 X 297)
www.panelook.com
Page 26
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
14.2 Packing Note
y Box Dimension : 233mm(W) u 613mm(L) u 445mm(H)
y Package Quantity in one Box : 8 pcs
14.3 Box label
y Label Size : 108 mm (L) u 56 mm (W)
y Contents
Model : HM236WU1-100
Q`ty : Module 8 Q`ty in one box
Serial No. : Box Serial No. See next page for detail description.
Date : Packing Date
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
0000000000000
Type Grade YearMonth ITEM-CODE Serial_no
SPEC. NUMBER
S
B2010-8002-O (3/3)
HM236WU1-100
0000000000000
5940
8
20XX.X.XX
Internal UseRoHS Mark
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
PAGE
Y]
OF 28
A4(210 X 297)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 27
Global LCD Panel Exchange Center
www.panelook.com
15.0 APPENDIX
Figure 1. Measurement Set Up
PRODUCT GROUP
TFT- LCD PRODUCT
REV
Rev.P1
ڃڧٻژٻڐڋھۈ ڄٻ
ISSUE DATE
Aug. 8. 11’
Figure 2. White Luminance and Uniformity Measurement Locations (9 points)
1928101728
1)1
1)41)5
1)71)81)9
1)21)3
1)6
108
540
972
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
PAGE
Y^
OF 28
A4(210 X 297)
www.panelook.com
Page 28
Global LCD Panel Exchange Center
www.panelook.com
Display data
Optical
Response
White(TFT OFF)
100%
90%
10%
0%
PRODUCT GROUP
TFT- LCD PRODUCT
Figure 3. Response Time Testing
Black(TFT ON)
TR
Figure 4. Cross Modulation Test Description
White(TFT OFF)
TF
REV
Rev.P1
ISSUE DATE
Aug. 8. 11’
Time
VIEW AREAVIEW AREA
(D/4, W/4)
L31
(3D/4, 3W/4)
(D, W)
YA(7D/8,W/2)
(D, W)
L0
Cross-Talk (%) =
YB-Y
Y
A
A
ശ 100
Where: YA= Initial luminance of measured area (cd/m2)
YB= Subsequent luminance of measured area (cd/m2)
The location measured will be exactly the same in both patterns
YB(7D/8,W/2)
SPEC. NUMBER
S
SPEC. TITLE
HM236WU1-100 Product Specification_Rev.P1
B2010-8002-O (3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!