THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BEG
REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HF AND
MUST BE RETURNED TO BOE HF UPON ITS REQUEST
www.panelook.com
PROPRIETARY NOTE
SPEC. NUMBER
PRODUCT GROUP
TFT-LCD
Rev.
P0
ISSUE DATE
2012.03.22
HB140WX1-300
Preliminary Product Specification
Rev. P0
PAGE
1
OF 36
HEFEI BOE OPTOELECTRONICS TECHNOLOGY
R2010-6053-O(1/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
1
A4(210 X 297)
A4(210 X 297)
www.panelook.com
Page 2
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
G
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
2
REVISION HISTORY
REV. ECN No. DESCRIPTION OF CHANGES DATE PREPARED
P0-Initial Release 2012.03.22
৩⦡
R2010-6053-O(2/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
2
A4(210 X 297)
www.panelook.com
Page 3
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
No. Items Page
1.0General Description 4
2.0Absolute Maximum ratings 6
3.0Electrical specifications. 7
4.0Optical specifications. 9
PRODUCT GROUP
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
REV
Contents
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
3
5.0Interface Connection 14
6.0Signal Timing Specification 18
7.0Signal Timing waveforms 20
8.0Input Signals, Display Colors & Gray Scale of Colors 22
9.0Power Sequence 23
10.0Connector description 24
11.0Mechanical Characteristics 25
12.0Reliability Test 26
13.0Handling & Cautions. 26
14.0Label 27
15.0Packing information 29
16.0Mechanical Outline Dimension 30
17.0EDID Table 32
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
3
A4(210 X 297)
www.panelook.com
Page 4
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
4
1.0 GENERAL DESCRIPTION
1.1 Introduction
HB140WX1-300 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 14.0 inch
diagonally measured active area with WXGA resolutions (1366 horizontal by 768 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this
module is a low reflection and higher color type. Therefore, this module is suitable for
Notebook PC. The LED Driver for back-light driving is built in this model.
All input signals are LVDS interface compatible.
LVDS
Connector
Input
Signal
1
VDD
LED Driver
LVDS Rx
+
T/CON
+
Mini-LVDS Tx
DC/DC
Gamma
Vcom
LED Lighting Bar
TFT LCD Panel
BACK LIGHT (Fluorescent Lamp)
1366 ശ768
Source Driver
1.2 Features
z 1 Channel LVDS Interface with 1 pixel / clock
z Thin and light weight
z 6-bit color depth, display 262K colors
z Single LED Lighting Bar. (Top side/Horizontal Direction)
z Data enable signal mode
z Up/Down Mounting Frame
z Green Product (RoHS & Halogen free product)
z On board LED Driving circuit
z Low driving voltage and low power consumption
z On board EDID chip
Gate Driver
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4
A4(210 X 297)
www.panelook.com
Page 5
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
5
1.3 Application
z Notebook PC (Wide type)
1.4 General Specification
The followings are general specifications at the model HB140WX1-300. (listed in Table 1.)
<Table 1. General Specifications>
ParameterSpecificationUnit Remarks
Active area
Number of pixels
Pixel pitch
309.4(H) ശ173.95(V)
1366 (H) ശ768 (V)
0.2265(H) ശ0.2265 (V)
mm
pixels
mm
Pixel arrangement RGB Vertical stripe
Display colors 262Kcolors
Display mode Normally White
Dimensional outline 320.9(H)*187.6(V)*3.6(Max) mm
Weight 320 (max) g
Surface treatment Hard-Coating 3H
Back-light Upper edge side, 1-LED Lighting Bar type Note 1
Power consumption P
: 0.9 (max) W
D
P
: 2.3 (max) W
BL
P
: 3.2 (max) W
total
Notes : 1. LED Lighting Bar (36*LED Array)
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5
A4(210 X 297)
www.panelook.com
Page 6
Global LCD Panel Exchange Center
Operating Range
Storage Range
-40 -20 0 20 40 60 80
Temperature (ఁ )
(40, 95)
(50, 80)
(60, 27)
100
80
60
40
20
90
Relative Humudity
5
Storage Range
www.panelook.com
SPEC. NUMBER
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
6
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. Absolute Maximum Ratings>
ParameterSymbolMin.Max.UnitRemarks
Power Supply Voltage V
Logic Supply Voltage V
DD
IN
-0.3 4.0 V
Vss-0.3 VDD+0.3 V
Ta=25+/-2¶C
Note 1
Operating Temperature T
OP
0 +50
ć
Note 2
Storage Temperature T
ST
-20+60
ć
Notes : 1. Permanent damage to the device may occur if maximum values are exceeded
functional operation should be restricted to the condition described under normal
operating conditions.
2. Temperature and relative humidity range are shown in the figure below.
O
95 % RH Max. ( 40
Maximum wet - bulb temperature at 39
C ≥ Ta)
O
C or less. (Ta > 40 OC) No condensation.
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6
A4(210 X 297)
www.panelook.com
Page 7
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
SPEC. NUMBER
3.0 ELECTRICAL SPECIFICATIONS
3.1 Electrical Specifications
ParameterMin.Typ.Max.UnitRemarks
Power Supply Voltage V
Permissible Input Ripple
Voltage
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
< Table 3. Electrical specifications >
DD
V
RF
REV
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
7
Ta=25+/-2¶C
3.0 3.3 3.6 V Note 1
- - 100mVAt VDD = 3.3V
Power Supply Current I
Positive-going Input
Threshold Voltage
Negative-going Input
Threshold Voltage
V
V
Differential Input Voltage V
Power Consumption
P
P
DD
P
total
IT+
IT-
ID
D
BL
- 192- mANote 1
- - 100mV
cm = 1.2V typ.
V
-100- - mV
200- 600mV
- 0.64 0.9 W Note 1
- 2.3 W Note 2
- 2.84 3.2 W
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for 3.3V at 25ć.
a) Typ : Window XP pattern
b) Max : Vertical 2 line skip pattern
2. Calculated value for reference (V
LED ശ ILED)
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
2. The LED Life-time define as the estimated time to 50% degradation of initial luminous.
8
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
A4(210 X 297)
www.panelook.com
Page 9
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
SPEC. NUMBER
3.0 ELECTRICAL SPECIFICATIONS
3.3 LED structure
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
REV
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
9
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
9
A4(210 X 297)
www.panelook.com
Page 10
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
10
4.0 OPTICAL SPECIFICATION
4.1 Overview
The test of Optical specifications shall be measured in a dark room (ambient luminance d 1
lux and temperature = 25r2ć) with the equipment of Luminance meter system (Goniometer
system and TOPCON BM-5) and test unit shall be located at an approximate distance
50cm from the LCD surface at a viewing angle of θ and Φ equal to 0q. We refer to θØ=0(=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction(“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) andθØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θand/or Ø, the center
of the measuring spot on the Display surface shall stay fixed. The backlight should be
operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25qC.
Optimum viewing angle direction is 6 ’clock.
4.2 Optical Specifications
<Table 5. Optical Specifications>
Parameter Symbol Condition Min. Typ. Max. Unit Remark
Θ
Θ
Θ
Θ
12
3
9
6
CR > 10
Viewing Angle
Horizontal
range
Vertical
Luminance Contrast ratio CRΘ = 0q500600Note 2
Luminance of
White
White
Luminance
uniformity
White Chromaticity
Reproduction
of color
Response Time
(Rising + Falling)
5 Points Y
w
Θ = 0q
5 Points ΔY580- -
LED = 20mA
I
13 Points ΔY1365- -
x
Red
Green
Blue
w
y
w
x
R
y
R
x
G
y
G
x
B
y
B
T
RT
Θ = 0q
Θ = 0q-0.03
Ta= 25q C
Θ = 0q
4045- Deg.
4045- Deg.
Note 1
1520- Deg.
3045- Deg.
2
170200- cd/m
Note 3
Note 4
0.283 0.313 0.343
Note 5
0.299 0.329 0.359
0.592
0.347
0.329
0.571
+0.03
0.151
0.115
- 1216msNote 6
Cross Talk CTΘ = 0q- - 2.0 % Note 7
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
10
A4(210 X 297)
www.panelook.com
Page 11
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
11
Notes :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing
angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12
o’clock direction with respect to the optical axis which is normal to the LCD surface (see
FIGURE 1).
2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of
the LCD surface. Luminance shall be measured with all pixels in the view field set first to
white, then to the dark (black) state .
(see FIGURE 1) Luminance Contrast Ratio (CR) is defined mathematically.
Luminance when displaying a white raster
CR =
Luminance when displaying a black raster
3. Center Luminance of white is defined as luminance values of 5 point average across
the LCD surface. Luminance shall be measured with all pixels in the view field set first to
white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of
the measurements per display.
4. The White luminance uniformity on LCD surface is then expressed as : ΔY =Minimum
Luminance of 5(or 13) points / Maximum Luminance of 5(or 13) points.
(see FIGURE 2 and FIGURE 3).
5. The color chromaticity coordinates specified in Table 5 shall be calculated from the
spectral data measured with all pixels first in red, green, blue and white. Measurements
shall be made at the center of the panel.
6. The electro-optical response time measurements shall be made as FIGURE 4 by
switching the “data” input signal ON and OFF. The times needed for the luminance to
change from 10% to 90% is Tr, and 90% to 10% is Td.
7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing
the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to
the luminance (YB) of that same area when any adjacent area is driven dark.
(See FIGURE 5).
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
11
A4(210 X 297)
www.panelook.com
Page 12
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
SPEC. NUMBER
4.3 Optical measurements
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
Photo detector
(TOPCON BM-5A)
TFT-LCD module
TFT- LCD PRODUCT
Figure 1. Measurement Set Up
Field = 2
o
50 cm
LCD panel
REV
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
12
Center of the screen
Optical characteristics measurement setup
Figure 2. White Luminance and Uniformity Measurement Locations (5 points)
Center Luminance of white is defined as luminance values of center 5 points
across the LCD surface. Luminance shall be measured with all pixels in the view
field set first to white. This measurement shall be taken at the locations shown in
FIGURE 2 for a total of the measurements per display.
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The White luminance uniformity on LCD surface is then expressed as : ΔY5 =
Minimum Luminance of five points / Maximum Luminance of five points (see
FIGURE 2) , ΔY13 = Minimum Luminance of 13 points /Maximum Luminance of
13 points (see FIGURE 3).
Figure 4. Response Time Testing
Display data
Optical
Response
100%
90%
10%
0%
White(TFT OFF)
TR
Black(TFT ON)
White(TFT OFF)
TF
Time
The electro-optical response time measurements shall be made as shown in
FIGURE 4 by switching the “data” input signal ON and OFF. The times needed
for the luminance to change from 10% to 90% is Td and 90% to 10% is Tr.
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
13
A4(210 X 297)
www.panelook.com
Page 14
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
VIEW AREA
PRODUCT GROUP
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
Figure 5. Cross Modulation Test Description
VIEW AREA
1025, 192
1025,576342,576
L0
(1195, 384)
Y
A
342,192
L31
REV
P0
Y
ISSUE DATE
2012.03.22
14
(1195, 384)
B
PAGE
OF 36
YB - Y
Cross-Talk (%) =
Y
A
ശ 100
A
Where:
Y
= Initial luminance of measured area (cd/m2)
A
YB = Subsequent luminance of measured area (cd/m2)
The location measured will be exactly the same in both patterns
Cross-Talk of one area of the LCD surface by another shall be measured by
comparing the luminance (YA) of a 25mm diameter area, with all display pixels
set to a gray level, to the luminance (YB) of that same area when any adjacent
area is driven dark (Refer to FIGURE 5).
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
14
A4(210 X 297)
www.panelook.com
Page 15
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
15
5.0 INTERFACE CONNECTION.
5.1 Electrical Interface Connection
The electronics interface connector is STM or Compatible or equivalent. The mating
connector part number is I-PEX 20455-040T-11 or Compatible. The connector interface pin
assignments are listed in Table 6.
<Table 6. Pin Assignments for the Interface Connector>
Terminal Symbol Functions
Pin No. Symbol Description
1 NCNo Connection
2 VDDIN Power Supply, 3.3V (typ.)
3 VDDIN Power Supply, 3.3V (typ.)
4 VDC VDC 3.3Vpower for EDID
5 NCNo Connection
6 CLK EDID EDID Clock
7 Data EDID EDID Data
8 RxIN0- Transmission Data of 0 Negative -
9 RxIN0+Transmission Data of 0 Positive +
10GND Ground
11RxIN1- Transmission Data of 1 Negative -
12RxIN1+Transmission Data of 1 Positive +
13GND Ground
14RxIN2- Transmission Data of 2 Negative -
15RxIN2+Transmission Data of 2 Positive +
16GNDGround
17RxCLKIN- Sampling Clock of Negative -
18RxCLKIN+ Sampling Clock of Positive +
19NCNo Connection
20NCNo Connection
21
22
23
24
25
26
27
28
29
30
NCNo Connection
GNDGround
NCNo Connection
NCNo Connection
GNDGround
(CE) No Connection
(CTL) No Connection
GNDGround
NCNo Connection
NCNo Connection
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
15
A4(210 X 297)
www.panelook.com
Page 16
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
Terminal Symbol Functions
Pin No. Symbol Description
31VLED_GNDLED Ground
32 VLED_GNDLED Ground
33 VLED_GNDLED Ground
34 NCNo Connection
35 PWMSystem PWM Signal Input
36 LED_ENLED enable pin(+3.3V Input)
37 CABCCABC enable pin (0:Bypass;1 Enable)
38 VLEDLED Power Supply 6V-21V
39 VLEDLED Power Supply 6V-21V
40 VLEDLED Power Supply 6V-21V
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
16
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
16
A4(210 X 297)
www.panelook.com
Page 17
Global LCD Panel Exchange Center
6
6
6
L
S
G0~G5
B0~B5
Vsy
C
www.panelook.com
SPEC. NUMBER
5-2. LVDS Interface
PC Side
R0~R5
G0~G5
B0~B5
Hsync
Vsync
DE
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
17
TFT-LCD Side
CN1
6
6
6
TTL Parallel-to-LVDS
100 ohm
100 ohm
100 ohm
LVDS to TTL Parallel
VD
to TTL Parallel
6
6
6
R0~R5
G0~G5
B0~B5
Hsync
Hsync
nc
Vsync
D
DE
CLK
PLL
100 ohm
Note. Transmitter : Thine THC63LVDM63A or equivalent.
Transmitter is not contained in Module.
5.3.LVDS Input signal
CLK+
Rin0
Rin1
Vdiff=0V
GOR5R4R3R2R1R0
B1B0G5G4G3G2G1
PLL
PLL
LK
CLK
Rin2
Prior cycle
Note. Pin connection in case of using Thine THC63LVDM63A
DEVsync B5B4B3B2Hsync
Signal for 1 DCLK cycle Next cycle
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
17
A4(210 X 297)
www.panelook.com
Page 18
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
5.3 Data Input Format
<Table 6. Pin Assignments for the Interface Connector>
G
OXSXPG
yG nG iG yG nG iGyG nG iG yG nG iG
G
OYSXPG
PRODUCT GROUP
TFT- LCD PRODUCT
XGwGdGZGkG
yG nG iG
REV
P0
ISSUE DATE
2012.03.22
18
G
OXZ]\SXPGGOXZ]]SXPG
PAGE
OF 36
yG nG iG yG nG iGyG nG iG yG nG iG
OXS^]_PGOYS^]_PGOXZ]\S^]_PG OXZ]]SG^]_PG
Display Position of Input Data (V-H)
5.4 Back-light & LCM Interface Connection
Interface Connector: MS24022P10 or Equivalent
<Table 7. Pin Assignments for the BLU & LCM Connector>
Pin No. Symbol Description Pin No. Symbol Description
1 LED1 LED cathode connection 6 NCNo Connection
2 LED2 LED cathode connection 7 NCNo Connection
3 LED3 LED cathode connection 8 VoutLED anode connection
4 LED4 LED cathode connection 9 VoutLED anode connection
5 NCNo Connection 10VoutLED anode connection
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
18
A4(210 X 297)
www.panelook.com
Page 19
Global LCD Panel Exchange Center
oiX[W~XTZWWGG
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
SPEC. NUMBER
6.0 SIGNAL TIMING SPECIFICATION
6.1 The
Item Symbols Min Typ Max Unit
Frequency 1/Tc 67.5 72.3 76.3 MHz
Clock
High Time Tch - 4/7 - Tc
Low Time Tcl - 3/7 - Tc
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
is operated by the DE only.
REV
P0
ISSUE DATE
2012.03.22
19
778790802lines
PAGE
OF 36
Frame Period Tv
- 60 - Hz
- 16.7 - ms
Vertical Display Period Tvd 768768768lines
One line Scanning
Period
Horizontal Display
Period
Th144615261586clocks
Thd 136613661366clocks
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
19
A4(210 X 297)
www.panelook.com
Page 20
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
SPEC. NUMBER
6.2 LVDS Rx Interface Timing Parameter
The specification of the LVDS Rx interface timing parameter is shown in Table 8.
<Table 8. LVDS Rx Interface Timing Specification>
ItemGSymbolGMinGTypGMaxGUnitGRemarkG
CLKIN PeriodGtRCIPG-G13.83G25GnsecG
CLK DifferenceGtCdiffG
Input Data 0GtRIP1G-0.4G0.0G+0.4GnsecG
Input Data 1GtRIP0GtRICP/7-0.4GtRICP/7GtRICP/7+0.4GnsecG
Input Data 2GtRIP6G2 ശtRICP/7-0.4G2 ശtRICP/7G2 ശtRICP/7+0.4GnsecG
Input Data 3GtRIP5G3 ശtRICP/7-0.4G3 ശtRICP/7G3 ശtRICP/7+0.4GnsecG
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
-tRCIP*(3/7)
0G
+tRCIP*(3/7)
REV
P0
nsecG
ISSUE DATE
2012.03.22
PAGE
OF 36
20
Input Data 4GtRIP4G4
Input Data 5GtRIP3G5 ശtRICP/7-0.4G5 ശtRICP/7G5 ശtRICP/7+0.4GnsecG
Input Data 6GtRIP2G6 ശtRICP/7-0.4G6 ശtRICP/7G6 ശtRICP/7+0.4GnsecG
y Pick the pouch only, when taking out module from a shipping package.
(2) Cautions for handling the module
y As the electrostatic discharges may break the LCD module, handle the LCD module with
care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
y As the LCD panel and back - light element are made from fragile glass material, impulse
and pressure to the LCD module should be avoided.
y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth
without chemicals for cleaning.
y Do not pull the interface connector in or out while the LCD module is operating.
y Put the module display side down on a flat horizontal plane.
y Handle connectors and cables with care.
G(3) Cautions for the operation
y When the module is operating, do not lose CLK, ENAB signals. If any one of these
signals is lost, the LCD panel would be damaged.
y Obey the supply voltage sequence. If wrong sequence is applied, the module
would be damaged.
27
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
A4(210 X 297)
www.panelook.com
Page 28
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
PRODUCT GROUP
REV
TFT- LCD PRODUCT
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
28
(4) Cautions for the atmosphere
y Dew drop atmosphere should be avoided.
y Do not store and/or operate the LCD module in a high temperature and/or humidity
atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively
low temperature atmosphere is recommended.
(5) Cautions for the module characteristics
y Do not apply fixed pattern data signal to the LCD module at product aging.
y Applying fixed pattern for a long time may cause image sticking.
(6) Other cautions
y Do not disassemble and/or re-assemble LCD module.
y Do not re-adjust variable resistor or switch etc.
y When returning the module for repair or etc., Please pack the module not to be broken.
We recommend to use the original shipping packages.
14.0 LABEL
(1) Product label
1
Type designation
No 1. Control Number
2 3 4
5
6 7
X
X X X X X X X X X X X X X X X X
No 5. Month (1, 2, 3, …, 9, X, Y, Z)
No 6. Product Identification (FG)
No 2. Rank / Grade
No 7. Serial Number
No 3. Line classification
No 4. Year (10 : 2010, 11: 2011, …)
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
28
A4(210 X 297)
www.panelook.com
Page 29
Global LCD Panel Exchange Center
www.panelook.com
SPEC. NUMBER
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
(2) High voltage caution label
(3) Box label
Label Size: 110 mm (L) u 56 mm (W)
Contents
Model: HB140WX1-300
Q`ty: Module Q`ty in one box
Serial No.: Box Serial No. See next figure for detail description.
Date: Packing Date
Internal use of Product
PRODUCT GROUP
TFT- LCD PRODUCT
REV
P0
ISSUE DATE
2012.03.22
PAGE
OF 36
29
HB140WX1-300
0000000000000
00 0 0 00 0 0000 000000
Type Grade Line Year Month Internal use Serial No
40
201X.X.XX
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
29
A4(210 X 297)
www.panelook.com
Page 30
Global LCD Panel Exchange Center
s
www.panelook.com
PRODUCT GROUP
TFT- LCD PRODUCT
SPEC. NUMBER
SPEC. TITLE
HB140WX1-300 Preliminary Product Specification
15.0 PACKING INFORMATION
15.1 Packing order
-. Put Pad into the inner boxG
step1G
pGwG
REV
P0
-.Put module into the paper spacer and
modules bundled by PE BagG
wlGiG
ISSUE DATE
2012.03.22
PAGE
OF 36
30
step2G
step4G
-. 12ea Box/Pallet, 480ea MDL/PalletG
15.2 Notes
z Box Dimension: 580mm(W) x 450mm(D) x 280mm(H)
z Package Quantity in one Box: 40pcs
z Total Weight: 15kg
-. Put Cover on the top of the padG
jG
step3G
R2010-6053-O(3/3)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!