Bodine 07410295 Wiring Diagrams

Contact Us:

Tel: 1-800-7BODINE (U.S. only)
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
Corporate Web:

www.bodine-electric.com

CONNECTION DIAGRAM 07410295

6-Wire Dual-Voltage Reversible

Low Voltage

Line

Black-Yellow Tracer

Red-Yellow Tracer

Blue

MOTOR

Direction of Rotation: Clockwise

To reverse direction of rotation,
transpose Blue and Blue-Yellow Tracer leads.

Black

Red

Blue-Yellow Tracer

Green-Yellow Tracer

High Voltage

Black-Yellow Tracer

Blue

Black

Red-Yellow Tracer

Red

Blue-Yellow Tracer

Green-Yellow Tracer

MOTOR

BODINE LIMITED WARRANTY

The Bodine Electric Company warrants all products manufactured by it to be free of defects in workmanship and materials when used under Normal
Operating Conditions and when applied in accordance with nameplate specifications. This warranty shall be in effect for a period of twelve months from date
of purchase or eighteen months from date of manufacture, whichever comes first.
The Bodine Electric Company will, at its option, repair, replace, or refund the purchase price of any of its products, which has been found to be defective and
is within the warranty period, provided that the product is shipped freight prepaid, with previous authorization, to Bodine Electric, or to the nearest Bodine
Authorized Service Center. At its option, all return shipments are F.O.B. Bodine’s plant or Authorized Service Center. Bodine is not responsible for removal,
installation, or any other incidental expenses incurred in shipping the product to or from Bodine.

This warranty is in lieu of any other expressed or implied warranty—including (but not limited to) any implied warranties of merchantability and/or
fitness for a particular use or purpose.

Bodine’s liability under this warranty shall be solely limited to repair or replacement of the Bodine product within the warranty period and Bodine shall not be
liable, under any circumstances, for any consequential, incidental or indirect damages or expenses associated with the warranted products.
Commutators and/or brush wear and its associated effects are a normal occurrence and are not covered by this warranty unless otherwise agreed to by
Bodine in writing.
Any Bodine product, which is damaged due to misuse, abuse, negligence or has been modified or dismantled without the knowledge or written consent of
Bodine, is not covered by this warranty.

Motor/Gearmotor Serial No. _____________________ Purchase Date ____________ Installed By __________________

See Other Side for Safety, Installation, Use and Maintenance Information

Printing Instructions per SMKDI-770-01

Model: 07410295

eDOC:

Part No.:

0741029520140136

H

Gearmotor/Motor Safety,

Installation, Use, and

Maintenance Information

Thank you for selecting a gearmotor/motor from
Bodine Electric Company. With your new drive unit
you will find yourself enjoying the same high
performance and trouble free operation that has
been characteristic of Bodine products since 1905.
Bodine Electric Company prides itself on the
quality of design and manufacture of its products.
Great care is taken in an attempt to provide
products free of defects in workmanship, or
materials.

Safety

“The use of electric machines, like that of all
other utilization of concentrated power, is potentially
hazardous. The degree of hazard can be greatly
reduced by proper design, selection, installation,
and use, but hazards cannot be completely
eliminated. The reduction of hazard is the joint
responsibility of the user, the manufacturer of the
driven or driving equipment, and the manufacturer
of the machine”.
Bodine products are designed and manufactured
to comply to applicable safety standards and, in
particular, to those issued by ANSI (American
National Standards Institute), NEMA (National
Electrical Manufacturers Association), U.L.
(Underwriters Laboratories, Inc.), and CSA
(Canadian Standards Association).
Most Bodine products are “third party approved”
with respect to construction. Motors and
gearmotors having component recognition by U.L.
Inc. have a
that are CSA certified also have a or a
mark in the same location. If you need specific
information regarding the “third party approval” of
Bodine products, contact your Bodine
Representative, or the Corporate Headquarters.
However, since even well built apparatus can be
installed or operated in a hazardous manner, it is
important that the users observe safety
considerations. With respect to the load and
environment, the user must properly
and
aspects see safety standards publication No.
ANSI/NEMA MG-2.*

* Standards Publication No. ANSI/NEMA MG-2. “Safety
Standard for Construction and Guide for Selection, Installation
and Use of Electric Motors and Generators.”
Available from:
National Electrical Manufacturers Assoc.

www.nema.org

symbol on their nameplates. Those

select, install,

use

the apparatus—for guidance on all three

Selection

Before proceeding with the installation, the user
should review the application to confirm that the
proper drive has been selected. This should be
done after reading this notice and all applicable
safety standards. If in doubt, contact your Bodine
Representative or the Corporate Headquarters if
there is no Representative in your area. Any
selection or application suggestions made by
Bodine or their Representatives are only to assist
the customer—and in all cases, determination of
fitness for purpose or use is solely the customer’s
responsibility.

All nameplate ratings are based on the following

normal operating conditions

1. Duty: 8 hours per day; 5 days per week if
nameplated continuous duty (CONT), without
frequent reversals or starts and stops.

2. Ambient temperature 0°C to 40°C, unless
otherwise noted on the product nameplate.

3. Load: Uniform and free from shock or high
inertia.

4. Voltage: Within 10% of nameplate rating.

5. Frequency: Within 5% of nameplate rating.

6. Combined variation of voltage and frequency—
Within a total of 10% providing frequency
variation does not exceed 5%.

:

Variations from the above conditions may be
hazardous.

Installation

It is the responsibility of the equipment
manufacturer or individual installing the apparatus
to take diligent care in installing it. The National
Electrical Code (NEC), sound local electrical and
safety codes, and when applicable, the
Occupational Safety and Health Act (OSHA) should
be followed when installing the apparatus to reduce
hazards to persons and property.

Inspection

Examine the apparatus for damage from
shipment before connecting. Any claim(s) for
shipping damage should be made to the freight
carrier. Do not attempt to turn the output shaft of a
gearmotor with an externally applied torque arm.
Paint thickness of .006 maximum does not apply to
published dimensional values.

Mounting

Any screws or similar devices, that penetrate
the motor frame either for mounting the Bodine
product or mounting something to the product,
should be limited in length so as not to come in
contact with, or in close proximity to, intended
features that conduct electricity.
Bodine stock products are designed for
universal horizontal mounting. Vertical mounting,
with gearhead above motor is not normally
recommended. Consult the factory for custom
mounting requirements.

Connection

Follow nameplate for voltage, frequency, and
phase of power supply. See accompanying wiring
diagram as to connections for rotation (and
capacitor, resistor, relay, protector, if required).

When connecting, make sure that your
motor/gearmotor is securely and adequately
grounded—failure to ground properly may cause
serious injury to personnel.

available at:

www.bodine-electric.com

Wiring diagrams are

Wiring

For wire sizes and electrical connections refer to
the National Electrical Code (NEC), Article 430,
“Motors, Motor Circuits, and Controllers” and/or
applicable local area codes. Extension cords
should not be used.

Use

Additional Safety Considerations

The chance of electric shock, fires, or
explosions can be reduced by giving proper
consideration to the use of grounding, thermal and
over current protection, type of enclosure, and
good maintenance procedures.
The following information
foregoing safety considerations: This information is
not purported to be all-inclusive and the
aforementioned references should be consulted.

1. Bodine standard totally enclosed products are
neither explosion proof nor dust ignition proof
and are not certified for hazardous locations in
the presence of flammable/explosive gas,
vapor, or dust. When dealing with hazardous
locations, an approved or certified product is
generally the recommended approach. The
NEC and NEMA safety standards should be
consulted to determine if exceptions are
allowed.

2. Enclosed motors/gearmotors are suitable for
dirty, damp locations. For outdoor use,
enclosed motors must be protected by a IP-44
sealing kit or a cover while still allowing
adequate airflow.

supplements

the

3. Moisture will increase the electrical shock
hazard of electrical insulation. Therefore,
consideration should be given to the avoidance
of (or protection from) liquids in the area of
motors. Use of totally enclosed
motors/gearmotors will reduce the hazard if all
openings are sealed.

4. Motors/gearmotors that employ capacitors can
develop more than nameplate voltage across
the capacitor and/or capacitor winding
(depending on design). Suitable precautions
should be taken when applying such motors.

5. Do not rely upon self-locking gears or
permanent magnet, or energized motors to hold
a load in place if movement could result in
personal injury. Mechanical locking devices
should be used in such applications.

6. For motors driven by electronic controls, do not
use a function of the control for safety interlock
purposes. An independent switch or relay
should be used.

Before Starting

1. Before attempting to start, check all connections
and fuses.

2. Proper consideration should be given to rotating
members: Before starting, be sure keys,
pulleys, etc. are securely fastened.

Proper
guards should be provided to prevent hazards
to personnel while rotating.

3. Other mechanical considerations include proper
mounting and alignment of products and safe
loads on shafting and gearing.

Starting

The motor/gearmotor should be test-started in

1.

an unloaded state (because of possible reaction
torque, the drive should be securely mounted
when starting—even when unloaded).

If the drive unit does not start promptly and run

2.

smoothly, disconnect immediately.

If unable to correct the problem, contact your

3.

purchase source, or a Bodine Authorized
Service Center, describing the trouble in detail.
Include the serial number, type, and other
nameplate data. Do not dismantle the
product—tampering or disassembly
warranty.

voids

the

Mainentance

IMPORTANT—
equipment, disconnect power source (this
applies especially to equipment using automatic
restart devices instead of manual restart devices
and when examining or replacing brushes on
brush-type motors/gearmotors).
Clean regularly to prevent dirt and dust from
interfering with ventilation or clogging moving
parts.

Brush-Type Motors/Gearmotors—

performance, brush-type motors and gearmotors
need periodic user-maintenance. The
maintenance interval is best determined by the
user. Inspect brushes regularly for wear (replace
in same axial position). Replace brushes as
needed.

Products Employing Capacitors—

servicing motors/gearmotors employing
capacitors, always discharge the capacitor by
placing a conductor across its terminals before
touching the terminals with any part of your body.

Before

servicing or working on

For optimum

Before

Lubrication

All Bodine products are lubricated for life, and
do not require re-lubrication.
(All information and data are subject to change
without notice.)

Part No.:

07410295

H