Boca Flasher HPNFC-HO Installation Manual

Installation Manual

HPNFC-HO

WARNING: DO NOT LIFT FIXTURE BY CABLES.

This could result in permanent damage to both the xture and the cables. Damage resulting from grasping cables and/or putting

undue pressure on the cable connections will not be covered under the warranty! Do not attempt to install or use the HPNFC-HO

xture without reading the installation instructions and safety labels completely. Failure to adhere to these instructions could result in

serious injury or property damage. Do not modify, alter or attempt to service the HPNFC-HO. Doing so will void the warranty.

Installation Instructions

HPNFC-HO

Indoor/Outdoor Shallow Prole Line Voltage

Introduction:

The Boca HPNFC-HO is a line voltage xture that eliminates the need for secondary transformers, making installation contractor friendly.

The housing is a clear anodized aluminum with a durable nish making it weather and abrasion resistant. It is UL Listed for dry, damp or wet

location (model dependent). See layout drawings for model provided.

Maintenance:

CLEANING Dry and Damp (IP65) Rated Fixtures: To clean surface use a soft damp cloth.

Wet (IP68) Rated Fixtures: To clean surface use a soft cloth with mild soap and water.

STORAGE Store in a dry, well-ventilated area when product is not in

use. Keep the electrical cord away from heated surfaces
when in use or not in use. If cord shows signs of damage
do not use, return product to manufacturer.

Electrical Specifications:

1. Input Voltage: 90-120VAC, 230-277VAC

2. Total linear ft per 20A breaker: HO8 = 175’
Total linear ft per 20A breaker: HO6 = 200’
Total linear ft per 15A breaker: HO8 = 130’
Total linear ft per 15A breaker: HO6 = 150’

3. Input Current: HO8 = 114mA RMS per linear ft.
Input Current: HO6 = 95mA RMS per linear ft.

Fixtures must be installed by a qualied and
licensed electrician in accordance with all national,
state and local electrical codes and regulations.
If any part of this manual does not meet the
necessary codes and regulations, contact the
factory for more information before attempting
to install.

IP65

DAMP LISTING

Model Dependent

WET LISTING

IP68

Max temp: 55C

Min. temp: -40C

Turn Power Off At Circuit Breaker

Before Beginning Installation!

INCLUDED IN THIS PACKAGE:

HPNFCHO Fixtures

1

(In lengths shown on job specic drawings)

Power cord length is

6.5ft per UL standard

Mounting Brackets

2

(2 brackets per xture)

Fixed

3" Arc

OR

OR

PAGE 2 OF 8

6" Arc

Swivel

Job Specic Drawings

3

HPNFC-HO

Installation Instructions

HPNFC-HO

CAUTION: Before installing any type of clip (xed, swivel or arc) onto the mounting surface determine if the xtures have

rigid or twist lock connections at each end (examples of the rigid and twist lock types are shown in section 4).

Installation of clips for light fixtures
with RIGID Connections

1. Light fixtures that have rigid connections on each end must be installed in the same plane and must also be in a straight alignment.

Using a chalk line or laser, mark a line on the flat surface where the clips are to be mounted. Align each clip to the chalk line using

the same reference point on each clip (clip edge or hole) and space the clips according to the length of each fixture (see figure A).

Clip placement: Boca Flasher recommends clips to be installed 1.5” from end cap. (see figure 3A)

2. Snap in the first light fixture into the clips (see section 2, installing fixtures into clips). Snap the 2nd. light fixture into adjacent clips

ensuring that the connections will mate (male to female).

3. Slide the second light fixture into the first light fixture until fully seated.

4. C AUTION DO NOT MATE FIXTURES THAT ARE NOT IN LINE OR FORCE

THIS CAN CAUSE PERMANENT DAMAGE TO FIXTURE CONNECTION AND OPERA

5. Continue this process until all light fixtures are installed according to the job specific layout drawings.

6. Connect fixtures to power per section 4 and

FIGURE A: CLIP ALIGNMENT

TOGETHER BY WIGGLING.

TION.

5.

PAGE 3 OF 8

1. INSTALL CLIPS INTO SUBSTRATE

Installation Instructions

HPNFC-HO

Fixed Clips

1a

3” Arc & 6” Arc Bracket Installation

1a

1b

1b

Swivel Clips

1b

1a

▶

Install security screw using
supplied screw and driver.

Screw Information:

1.2.Screws not provided by Boca Flasher.
Boca Flasher recommends wide
washer pan head Phillips #8 screw
(not to exceed .418” in diameter).

3. Length of screw will vary depending
on mounting surface.

4. For outdoor installations, installer
should use a screw with
weatherproof coating.

2. INSTALL FIXTURE INTO CLIPS

2a

Place the notch on the clip
into the rst notch of the
xture.

▶

▶

▶

Second Notch

2b

Detent

Fixture will pivot on notch as
it is pushed down.

Clip will securely
snap into place.

snap!

PAGE 4 OF 8

2c

If using the Swivel Clip
or Arc Bracket loosen the
screw where the clip and
swivel bracket meet to ad­just angle of the xture.

▶

▶

Angle
Screw

3. CLIP POSITIONING

1

2

2

FIXTURE LENGTH

Fixed Mounting Clip

3a

Swivel Mounting Clip

3b

FIXTURE LENGTH

FIXTURE LENGTH

Installation Instructions

HPNFC-HO

Changing fixture mount angle adjustable swivel clips only

1. Loosen screw shown on figure 1, on both ends of light
fixture.

2. Adjust light fixture to desired angle.

3. Tighten angle screw to lock into position

.

Adjustable Angle Screw

Arc Mounting Clip

3c

Note: If angle screw can not be reached using a straight
Phillips screwdriver an offset Phillips screwdriver may be

Figure 1

required.

▶

FIXTURE LENGTH

PAGE 5 OF 8

Installation Instructions

HPNFC-HO

Installation of clips for light fixtures
with TWIST LOCK Connections

1. Light fixtures that have twist lock connections on each end may be installed in areas where the surface plane

levels between fixtures. Also, the light fixtures do n

2. Using a chalk line or laser mark a line on the flat surface where the 2 clips for the 1st. fixture are to be

3. Snap in the first light fixture into the clips (see section 2 installing fixtures into clips).

4. Using a chalk line or laser mark a line on the flat surface where the 2 clips for the 2nd fixture are to be mounted,

a slightly different plane as long as the cord between the 2 fixtures is long enough. Also, this fixture can be placed at a

the first fixture (see figure 4).

5. Snap in the 2nd light fixture into the clips (see section 2 installing fixtures into clips).

6. Continue this process until all light fixtures are installed according to the job specific layout drawings.

7. Connect fixtures to power per section

Figure 4

and 5.

4

ot have to be in straight alignment and can be laid out to different angles and patterns.

may be at slightly

mounted. (See Figure: A)

different

this fixture can be placed on

different angle than

4. coNNect fIxtuRes toGetheR

See above for information

4a

on determining layout.

Connect Male and Female

4b

twist lock cables in
order shown on job
specic drawings.

Push together and then twist until

4c

completely connected and sealed
if outdoors.

PAGE 6 OF 8

twISt LOCK COnnECtIOn

Add tape to twist locks.

Place thumb over tape at starting point and

PULL around connector area until tape overlaps itself.

For weather-tight applications only
See additional instructions for weather-tight tape

5.coNNect fIxtuRes to PoWeR

o

6. c

NNect to A DIMMING systeM

Installation Instructions

HPNFC-HO

7. ReM

7a

Slide a flat head screwdriver in
between the clip and xture.

oVING fIxtuRes fRoM clIPs

7b

While holding the xture with your
other hand, pull back on screwdriver
to release from notch.

*NOTE:

These xtures can dim on forward (leading)
or reverse (trailing) phase dimmers.

Boca Flasher does not recommend the use of
a “Smart” or phase-adaptive dimming module.

IF NECESSARY

Once released from one notch,

7c

xture can be fully removed.

PAGE 7 OF 8

IMPORTANT SAFETY REMINDERS:

1. DANGER:

To reduce the risk electric shock, always unplug the HPNFC-HO from electrical outlet before
cleaning. Cut breaker if outlet is not available.

2. To reduce the risk of burns, re, electric shock or injury to persons:

• UsetheHPNFC-HOonlyforitsintendeduseasdescribedintheseinstructions.

• DonotuseattachmentsnotrecommendedbyBocaFlasher.

• NeveroperatetheHPNFC-HOifithasadamagedcord,cableorplug,ifitisnotworking

properly, if it has been dropped or damaged, or dropped into water. If the seal appears to
be damaged/broken/torn return the xture to a service center for examination or repair.

• Keepcablesawayfromheatedsurfaces

• Neverdroporinsertanyobjectintoanyopening.

• Donotoperatewhereaerosol(spray)productsarebeingusedorwhereoxygen

is being administered.

Installation Instructions

HPNFC-HO

3. WARNING:

Do not attempt to install or use the HPNFC-HO without reading the installation instructions
and safety labels. Failure to adhere to these instructions could result in serious injury
or property damage.

4. Do not modify, alter or attempt to service the HPNFC-HO:

Doing so will void the warranty.

5. There are no serviceable parts within the HPNFC-HO:

Please contact your local representative if issues arise on site during or after installation.

6. Do not use sharp tools near or on the xture lens:

Doing so will result in property damage and void the warranty.

Boca Flasher, Inc.

508 S. Military Trail n Deerfield Beach, Florida n 33442 USA

Phone: [phone] n Fax: [phone]

www.bocaflasher.com

We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.
bocaflasher.com. For specific requirements, contact your Boca Flasher sales representative. Boca Flasher, Inc. 552 NW 77th Street Boca Raton,
Florida 33487 USA Phone: [phone] Fax: [phone] © 2015 Boca Flasher, Inc. All rights reserved. All names and trademarks are property
of their respective owners. REV 07-2017

IP65

DAMP LISTING

IP68

WET LISTING