Bobrick Metro1550, Accent1530 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

HIGH PRESSURE LAMINATE (HPL) TOILET PARTITIONS

1550 MetroSeriesTM and 1530 AccentSeries

IMPORTANT:

Storage and Handling Information on last page.

For faster, easier installation, please review these

instructions thoroughly prior to installation.

TM

FLOOR

ANCHORED

OVERHEAD

BRACED

CEILING

HUNG

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

PREPARATION

PRE-INSTALLATION

A. Structural support in walls and floors is not furnished

by Bobrick. Confirm that adequate backing is present
in wall, ceiling and floors prior to installation.

B. This installation booklet must be used with the Bobrick

layout sheets.

C. You may verify hardware receipt by cross-referencing

the last page of the layout sheets against the box
contents.

INSTALLATION STEPS

1. Lay Out All Anchor Locations ............................ Page 3

2. Install All Anchors ............................................. Page 4

3. Bracket and Screw Guide.................................. Page 5

4. Install Wall Brackets and Wall Posts .................. Page 6

5. Position Panels .................................................. Page 7

6. Install Stile-To-Panel Brackets ........................... Page 7

7. Install Stiles and Set Door Openings ................ Page 8

8. Install Headrail (if applicable) ............................ Page 9

9. Install Hinges .................................................. Page 10

10. Install Door Hardware ..................................... Page 11

11. Install Shoes ................................................... Page 12

12. Finish And Cleanup ......................................... Page 12

RECOMMENDED TOOLS:

CAUTION: Be sure to use proper safety gear.

1. Chalk Line

2. Plumb-bob

3. Masking Tape (for laying out holes on
floors/walls/ceilings to be drilled)

4. Tape Measure and Pencils

5. Center Punch

6. Electric and/or
Battery-Powered Drill

7. Drill Bits
#19 (.166") M4.2
3/16" (4.7mm)

5/16" (8mm)

7/16" (11mm)

8. Screwdrivers/Screwdriver Bits
slotted and phillips, #1, #2 and #3

9. Pin-Head Torx Screw Driver – (to

install door hardware) – Supplied
by Bobrick

3/8" (9.5mm) for Concrete/Masonry

Page 2

10. Shims

A. 1530 and 1550.64 option

uses stainless steel
hardware.

B. Organize components with

appropriate hardware.

C When calculating distances

to centerlines, all panels,
stiles, and doors are 1"
(25mm) thick.

D. Look for panel-to-stile

offsets indicated on the
layout sheets.

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

11. Adjustable Supports

1-1/2" to 12" (40–105mm)

12. Level

13. Wrench – 9/16" (14mm) open

end (2 reqd. for adjusting hex
nuts on anchors)

14. Hack Saw

15. Hammer

16 Safety Glasses

Stile

Centerline

X

Y

1/2''

(13mm)

Panel Centerlines

C

L

C

L

C

L

C

L

Stile

Centerline

Panel

Centerline

X

Y

C

L

C

L

Panel

Centerline

X

Y

C

L

Stile

Centerline

C

L

X

Y

Panel

Centerline

C

L

Stile

Centerline

Y

X

X

Hex Nut

Lock Washer

Flat Washers

Hex Nut

LAY OUT ALL ANCHOR LOCATIONSSTEP 1

LAYOUT EXAMPLES

LEGEND: Obtain Dimension from Bobrick Layout Sheet.

Fig. 1a: Floor-Anchored or Ceiling-Hung
Front-Entry Corner Layout.

Fig. 1b: Overhead-Braced
Alcove Closed Layout.

NOTE: The stiles are in-line with panel.

X Dim. = Stile Edge to Centerline of Mounting Hole. Y Dim. = Centerline-to-Centerline of Mounting Hole.

Fig. 1c: Floor-Anchored or Ceiling-Hung
Alcove Closed Layout. Inswing Door.

NOTE: The center stile is perpendicular to panel.

Fig. 1d: Floor-Anchored or Ceiling-Hung
Alcove Closed Layout. Outswing Door.

NOTE: The center stile is perpendicular to panel.

A. Refer to Bobrick layout sheets for component locations on your specific application.

B. From back wall, measure and mark the location of the stile centerline. Stile centerline = 1/2" (13mm) + panel length + gaps

specified on layout sheets.

C. From side wall and center of stile location, measure dimensions for floor or ceiling anchors according to layout sheet. Refer

to the drilling tables below for center-to-center distances between anchors. For example: Overhead-Braced stiles centerline
of floor anchor from edge of stile is 1" (25mm); dimension on 3" (8cm) stile is 1-1/2" (38mm).

Fig. 1e: Detail of Overhead-

Fig. 1f: Detail of Floor-Anchored or Ceiling-Hung Stile

Braced Stile

Floor Anchored Stile

NOTE: 16", 18", 20", 24" (41, 51, 46, 61cm) stiles have 2 leveling bars. Use the 2 outside slots
for the 2 anchors.

Drilling Table

Overhead-Braced Series — Standard & .64 Option Floor-Anchored Series & Ceiling-Hung Stiles Ceiling-Hung Series & .63 Option

Stile Size

(width)

3" (76mm) 1 1-1/2" (38mm) - 3" (76mm) 1 1-1/2" (38mm) - 3" (76mm) 1 1-1/2" (38mm) -

4" (102mm) 2 1" (25mm) 2" (50mm) 4" (102mm) 1 2" (50mm) - 4" (102mm) 2 5/8" (16mm) 2-3/4" (70mm)

5" (125mm) 2 1" (25mm) 3" (75mm) 5" (125mm) 2 1-1/8" (30mm) 2-3/4" (70mm) 5" (125mm) 2 5/8" (16mm) 3-3/4" (95mm)

6" (152mm) 2 1" (25mm) 4" (102mm) 6" (152mm) 2 5/8" (16mm) 4-3/4" (121mm) 6" (152mm) 2 5/8" (16mm) 4-3/4" (121mm)

7" (178mm) 2 1" (25mm) 5" (127mm) 7" (178mm) 2 5/8" (16mm) 5-3/4" (146mm) 7" (178mm) 2 5/8" (16mm) 5-3/4" (146mm)

8" (200mm) 2 1" (25mm) 6" (152mm) 8" (200mm) 2 5/8" (16mm) 6-3/4" (172mm) 8" (200mm) 2 5/8" (16mm) 6-3/4" (172mm)

10" (254mm) 2 1" (25mm) 8" (200mm) 10" (254mm) 2 5/8" (16mm)) 8-3/4" (222mm) 10" (254mm) 2 5/8" (16mm) 8-3/4" (222mm)

12" (305mm) 2 1" (25mm) 10" (254mm) 12" (305mm) 2 5/8" (16mm) 10-3/4" (273mm) 12" (305mm) 2 5/8" (16mm) 10-3/4" (273mm)

16" (406mm) 2 1" (25mm) 14" (355mm) 16" (406mm) 2 5/8" (16mm) 14-3/4" (375mm) 16" (406mm) 2 5/8" (16mm) 14-3/4" (375mm)

18" (457mm) 2 1" (25mm) 16" (406mm) 18" (457mm) 2 5/8" (16mm) 16-3/4" (426mm) 18" (457mm) 2 5/8" (16mm) 16-3/4" (426mm)

20" (508mm) 2 1" (25mm) 18" (455mm) 20" (508mm) 2 5/8" (16mm) 18-3/4" (475mm) 20" (508mm) 2 5/8" (16mm) 18-3/4" (475mm)

24" (610mm) 2 1" (25mm) 22" (560mm) 24" (610mm) 2 5/8" (16mm) 22-3/4" (578mm) 24" (610mm) 2 5/8" (16mm) 22-3/4" (578mm)

No. of

Holes

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

X

Dim.

Y

Dim.

Stile Size

(width)

No. of
Holes

X

Dim.

Y

Dim.

Stile Size

(width)

Ceiling-Hung Stile

No. of
Holes

X

Dim.

Y

Dim.

Page 3

Finished

Ceiling

Hex Nut

Split Lock Washer

Bevel Washer

Hex Nut

Structural

Beam

Spacer

Flat Shoe Retainer

Hex Nuts

Flat Washers

Split Lock Washer

Leveling Bar

Threaded Rod

Hex Nut

1'' Ref.

(25mm)

or as

Required

Floor

L-Bracket

#14 x 1-3/4"

(6.4 x 45mm)

St. Stl.

Sheet-Metal

Screw

#14-16

Plastic Anchor

Shoe

Retainer

Flat Washer

Hex Nut
Hex Nut

Flat Shoe Retainer

Wedge Anchor

2-1/8'' to 2-1/4''

(54 to 60mm)

1-5/8'' to 1-3/4''

(41 to 44mm)

Flat Washer

Leveling Bar

Install when
stile is placed
on anchor bolts.

Flat Washer

Hex Nut

Lock Washer

1'' Ref.

(25mm)

or as

Required

INSTALL ALL ANCHORSSTEP 2

OVERHEAD BRACED FLOOR ANCHORS

A. Based on stile size locate centerline of floor L-brackets

from Drilling Table. (See page 3).

B. Drill 5/16" (8mm) diameter hole to 1-3/4" (45mm)

minimum depth. Remove all loose material from holes.
C. Install plastic anchors into holes.
D. Place one shoe retainer bracket at each hole location.
E. Place floor L-bracket on top of and inside each shoe

retainer.
F. Install #14 x 1-3/4" (M6.4 x 45mm) floor screws to retain

bottom floor L-brackets and shoe retainers. Do NOT

tighten screws. Screws should be loose enough to adjust

the floor L-brackets.
G Using the stile as a measurement tool, adjust the floor

L-brackets to fit inside the stile brackets. Mark locations.
H. Remove stile and tighten floor screws securely.

NOTE: Wood-floor anchors are available upon request. To
install drill 3/16" pilot hole in the floor and install using #14 x
1-3/4" (M6.3 x 45mm) screws.

FLOOR ANCHORS. Standard

A. Drill 3/8" (9.5mm) diameter hole to 2" (50mm) minimum

depth. Remove all loose material from holes.
B. Insert expansion shield (threaded side down) with

threaded rod into mounting hole. Extra flat washers are

supplied. Place as many flat washers as necessary onto

rod to ensure shoe retainer is placed above finished floor

surface. Install and tighten a hex nut above washer(s) and

shoe retainer, tightening and expanding anchor to secure

to floor. Make sure when tightening bolt that shoe retainer

is positioned properly to accept shoe (see Fig. 2b for

proper shoe retainer position).
C. Add a second hex nut, then a flat washer.
D. Set aside the third hex nut, flat washer, and the lock

washer. Install when stile is placed on anchor bolts.
E. Repeat process for each floor anchor.

NOTE: Wood-floor anchors are available upon request.

Fig. 2a: Detail of Overhead-Braced
Floor Anchor.

Fig. 2b: Detail of Floor Anchor.

CEILING ANCHORS.

NOTE: Ceiling anchors are to be installed before finished
ceiling is applied. All structural framing is to be furnished by
others. For Bobrick recommendations, refer to Bobrick Form
No. TB-32.

A. Drill 7/16" (11mm) diameter hole through structural

beam. Insert threaded rod through hole in beam. Rod

is furnished standard 6" (150mm) length. Longer rods

should be purchased locally if required.
B. Drop a bevel washer and lock washer over rod. Screw on

one hex nut.
C. Install second hex nut against bottom of beam and

tighten.
D. Install spacer, shoe retainer, flat washer, and a third

hex nut. Make sure shoe retainer is in proper position

to accept shoe (see Fig. 2c for proper shoe retainer

position).
E. Install remaining flat washers (2), lock washer (1), and

hex nuts (2), as shown in Fig. 2c.
F. Repeat process for each ceiling anchor.

Page 4

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

Fig. 2c: Detail of Ceiling Anchor.

F-bracket

Qty. (2)

Y-bracket

Qty. (3)

U-bracket

Qty. (3)

L-bracket

Qty. (3)

Y-bracket

Qty. (2)

Y-bracket

Qty. (3)

L-bracket

Qty. (3)

Y-bracket

Qty. (2)

Y-bracket

Qty. (3)

1000974

Y-bracket

Qty. (3)

L-bracket

Qty. (3)

Y-bracket

Qty. (3)

F-bracket

Qty. (2)

L-bracket

Qty. (3)

Y-bracket

Qty. (2)

Y-bracket

Qty. (3)

L-bracket

Qty. (3)

BRACKETS AND SCREW GUIDE

F-bracket U-bracket Y-bracket

#1000353

Internal Panel to Wall

#1002500

#12 x 3/4" (M5.5 x 19mm)

Panel/Stile Screws

#1000356

Internal Panel to Stile

External Panel or Stile

Pilot Hole Sizes—

• #19 (.166) x 3/4" (4.2 x 19mm)

• For attachment of brackets to panels.

• Do not through-drill.

NOTE: Adequate wall backing is required. High-quality drill bit is suggested for drilling into steel-core stiles.

• 3/16" x 3/4" (4.7 x 19mm)

• For attachment of U-brackets, L-brackets
or Y-brackets to steel-core stiles only.

• Do not through-drill.

EXAMPLE BRACKET APPLICATIONS.

#1000974

to Wall or Panel

L-bracket

#1000351

External Panel to Stile

#1002495

#12 x 2" (M5.5 x 50mm)

Wall Screws

• #19 (.166) x 2" (4.2 x 50mm)

• For attachment of all wall brackets
to stud backing.

Front-Entry Corner Layout.

NOTE: The stile is
in-line with panel.
No hardware is
exposed on the
outside of stall.

NOTE:
U- and F-brackets
are used on
internal panels
only, where there
is an adjoining
stall to conceal the
hardware.

Floor-Anchored or Ceiling-Hung
Alcove Closed Layout.

NOTE: The stile is
perpendicular to
panel. No hardware
is exposed on the
outside of stall.

Overhead-Braced Alcove Open Layout
and Adjoining Front-Entry Stall.Overhead-Braced Alcove Closed Layout.

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

Page 5

67-1/2''

(171cm)

41''

(104cm)

64''

(163cm)

Panel

Centerlines

Floor Anchors

14-3/4''

(37cm)

18''

(46cm)

Wall Post

54-1/2''

(138cm)

27-1/2''

(69cm)

64''

(163cm)

18''

(46cm)

Panel
Centerline

64''

(163cm)

43''

(109cm)

Floor Anchors

18''

(46cm)

Stile

Centerline

64''

(163cm)

18''

(46cm)

Panel Centerline

64''

(163cm)

Floor Anchors

Panel Centerline

18''

(46cm)

STEP 3

INSTALL WALL BRACKETS AND WALL POSTS

A. Measure and mark the locations of centerlines for all

the stiles and panels on walls.

B. Using the wall brackets as templates, measure

and mark the location of all mounting holes, plumb

according to dimensions shown in illustrations (Fig.

3a, 3b, 3c).

C. Use #19 (.166) drill bit (4.2mm) for 2" (50mm) deep

pilot holes into adequate wall backing.

D. Secure wall brackets with 1002495 screws.

These mounting points require wall backing.

Obtain Dimension from Bobrick Layout Sheet.

Fig. 3b: Overhead-Braced Alcove Closed
Layout.

Fig. 3a: Front-Entry Corner Layout with
Wall Post.

WALL POST #1002250

A. Determine the location and hole of the 1" x 1-1/2"

(25 x 40mm) stainless steel wall post being installed.
Outside edge of wall post to be in-line with outside
edge of keeping stile. The wall must have adequate
backing at mounting location to support door hung in
place.

Page 6

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

B. Install wall post at given height and fasten, plumb in

both directions to wall with (5) wall screws provided.
Install (2) post end caps and (5) mounting hole plugs.

C. Attach door with through bolts provided as you install

door(s) on pages 13.

Fig. 3c: Floor-Anchored or Ceiling-Hung
Alcove Open Layout.

Panel Centerline

6''

(15cm)

69''

(175cm)

29''

(74cm)

52''

(132cm)

Panel Centerline

82-5/16''
(209cm)

18''

(46cm)

64''

(163cm)

41''

(104cm)

64''

(163cm)

43''

(109cm)

18''

(46cm)

64''

(163cm)

18''

(46cm)

12''

(31cm)

STEP 4

POSITION PANELS

1. Place adjustable supports in position for each panel to
hold them 12" (305mm) above the floor.

2. Place panels on the supports and into their respective
wall brackets. Do not secure panels to wall brackets at

this time.

Fig. 4: Panel and Adjustable Supports.

STEP 5

INSTALL STILE-TO-PANEL BRACKETS

Fig. 5a: Floor-Anchored or
Ceiling-Hung Bracket
Placement.

For

Internal

Panel

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

(Refer to

examples

on page 5.)

For

External

Panel

CAUTION: Panel centerline is not
always on the stile centerline. Refer
to Bobrick Layout Sheets for panel
offsets.

A. Measure and mark the centerlines

for three (3) U- or L-brackets per
stile.

B. Using U- or L-bracket as a template,

mark the location of all mounting
holes.

C. For U- or L-brackets attached to

steel-core stiles, use a high-quality
drill bit 3/16'' (4.7mm) for 3/4"
(19mm) deep pilot holes.

D. Caution: Do not drill through the

stile. For L-brackets attached to the
edge of stile, use a #19 (.166) drill
bit (4.2mm) for 3/4" (19mm) deep
pilot holes.

E. Secure U- or L-brackets
with 1002500 screws.

Fig. 5b: Overhead-Braced
Bracket Placement.

For

Internal

Panel

(Refer to

examples

on page 5.)

For

External

Alcove
In-Line

Panel

Page 7

Stile Bracket

Floor L-Bracket

#14 x 5/8''

(6.4 x 16mm)

St. Stl.

Sheet-Metal

Screw

#14 x 1-3/4''
(6.4 x 45mm)

St. Stl. Sheet-Metal Screw

Leveling Bolt

#14-16

Plastic Anchor

Finish Face

of Floor

#14 x 5/8''

(6.4 x 16mm)

St. Stl.

Sheet-Metal

Screw

#14 x 1-3/4''
(6.4 x 45mm)

St. Stl. Sheet-Metal

Screw

#14-16

Plastic Anchor

12''

(305mmn)

Hex Nut

Flat Washers

Lock Washer

Hex Nuts

Threaded Rod

Flat Shoe Retainer

Expansion Shield

Leveling

Bar

Step A

Flat Washer

Hex Nut

Lock Washer

Flat Washers

Hex Nut

Hex Nut

Lock Washer

Flat Washers

Hex Nut

INSTALL STILES AND SET DOOR OPENINGSSTEP 6

Floor-Anchored and Ceiling-Hung Series

A. Place the stiles onto the threaded rods of anchors. Add a flat washer, lock washer, and a third hex nut to each

threaded rod of floor anchors (these should already be in place on ceiling anchors—refer back to Fig. 2b). Do not

tighten hex nuts at this time.

B. Ensure edge of panel is touching screw heads in brackets on stiles. Using brackets as templates, drill 3/16" (.187) x
5/8" (6.4 x 16mm) pilot holes in panel.
C. Fasten brackets to panels with #14 x 5/8" (6.4 x 16mm) screws or 1002500 for stainless steel option.
D. Use level to plumb stiles. Place shims between panels and wall.
E. Set door openings to be square, plumb and true per Bobrick Layout Sheets.
F. Tighten hex nuts on stile anchoring system.
G. Secure panels to wall brackets using #14 x 5/8" screws or 1002500 for stainless steel option.

Fig. 6a: Ceiling-Hung Installation Fig. 6b: Front View Ceiling-Hung Stile

Obtain Dimension from Bobrick Layout Sheet.

Overhead-Braced Series

A. Install leveling bolt into stile.
B. While stile is laying flat, rotate leveling bolt so that overall stile dimension is 82-5/16" (209cm) from the head of the

leveling bolt to the top edge of stile.
Note all floor slopes and adjust stile heights accordingly.
C. Mount stile and install #14 x 5/8" (6.4 x 16mm) screws through the side of stile bracket into the floor L-bracket. Leave

screws loose. (Fig. 6d)

D. Level and plumb the panels. Using stile U-bracket as a template, drill 3/16" (5mm) pilot holes into the panel.
Special note: U-bracket panel hole should be a minimum of 1/2" (13mm) off edge of panel.
F. Fasten U and F-brackets to panels with #14 x 5/8" (6.4 x 16mm) screws or 1002500 for stainless steel option.
G. Level and plumb stile. Tighten stile bracket screws #14 x 5/8" into floor L-bracket.

Fig. 6c: Panel Installation

Fig. 6d: Front View
Overhead-Braced

Fig. 6e: Side View
Overhead-Braced

Page 8

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

Stile

Stile

Panel

Front Headrail

Outswing Door

Return Headrail

*

End Cap

Stile

Stile

Panel

# 12 x 2''

St. Stl. Sheet-Metal

Screws

Stile

Stile

Panel

Return Headrail

Front Headrail

Headrail Bracket

Back Wall

# 12 x 7/16''

St. Stl.

Sheet-Metal

Screws

Wall

STEP 7

INSTALL HEADRAIL (IF APPLICABLE)

Note: Bobrick provides headrail in 84" (213cm) long

sections. Headrail seams must be located over stiles.

A. Measure wall-to-wall dimension less 1/4" (6mm). For

corner application, measure from wall to outside edge
of stile less 1/8" (3mm).

B. Place headrail over top of stiles.

C. Drill #19 (.166) x 3/4" (4.2 x 19mm) pilot holes through

interior sides of headrail into stiles. Fasten headrail to
stile using #12 x 7/16" (M5.5 x 10mm) screws.

D. For corner and alcove layouts, cut return headrail 1/8"

less than dimension from inner edge of headrail to the
back wall.

E. Using headrail L-bracket as a template, mark the

location for mounting holes in back of front headrail
and wall.

F. Drill #19 (.166) x 3/4" (4.2 x 19mm) pilot holes. Fasten

headrail L-bracket to stile using #12 x 7/16" (M5.5 x
10mm) screws.

G. Drill #19 (.166) x 2" (4.2 x 50mm) pilot holes in wall.

Fasten headrail L-bracket to wall using #12 x 2" (M5.5
x 50mm) screws.

H. Insert headrail return piece into headrail L-bracket.

Secure with #12 x 7/16" (M5.5 x 10mm) screws.

I. For corner layouts, install end cap to finish open

headrail end.

Fig. 7a: Alcove Configuration.

Fig. 7b: Headrail Installation Hardware.

Corner Configuration.

Fig. 7c: Detail of End Cap.

Back viewFront view

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

Page 9

STEP 8

INSTALL HINGES

Hinge

A. Using hinge diagram at left, identify the upper and lower hinge set for right hand or left hand installation. Locate

#1002156 cam for upper hinge.
B. Separate hinge sets and fasten the 2 halves that have plastic bushings with “teeth” and cam alignment tabs onto stile

using driver and (1/4-20" x 34") screws. Refer to diagram to ensure “J” and “L” halves are located properly.
C. Fasten remaining upper hinge half to door.
D. Insert hinge pin and #1002156 plastic cam on upper stile hinge half.
E. Lift door and position onto upper stile hinge half. Door should be hanging securely on upper hinge.
F. Insert remaining hinge pin in lower door and hinge half and mount to door.

To Increase or Decrease Opening of Door.

A. Alignment tabs have been formed into the cam and plastic hinge bushing.
B. Lift door to limit of upward travel (approximately 1/2"). While door is lifted, raise cam above bottom bushing and rotate

so alignment tabs meet.
C. To set door in open position, rotate cam toward door opening direction.
D. To set door in closed position, rotate cam toward door closing direction.
E. Door may not function properly if cam and bushing tabs are not aligned properly.
F. When the cam has been set at the desired free resting position, “either closed or open” the top of the affixed

components will be aligned
Tip – Industry tolerance in the hardware will sometimes allow fine alignment to some partition components.

These fine adjustments may be performed by loosening the hardware screws and adjusting the components

the direction needed and retightening the screws.

Remove clothes hook, latch, keepers, brass inserts, latch track.

Fig. 8a: Hinge Configuration.

Cam

Adjustment Points

Door Half

#1002330

2 x “L”

Hinge Set

Top Hinge

(With Cam)

Stile

Half

Bottom

Hinge

#1002331

2 x “J”

Hinge Set

(No Cam)

Cam

#1002156

#1002331

2 x “J”

Hinge Set

Stile

Half

#1002330

2 x “L”

Hinge Set

Fig. 8b: Right-Hand Inswing Door.

Stile

Cam

Lower Hinge

Upper Hinge

Stile

Door

Page 10

Door Half

Right Hand

Inswing

or
Left Hand
Outswing

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

Left Hand

Inswing

or

Right Hand

Outswing

INSTALL DOOR HARDWARESTEP 9

Inswing

A. Mount latch and keepers as shown (Fig. 9f) using

1002500 (#12 x 3/4") screws.

Perpendicular Keeping Stile: Mount latch as shown

(Fig. 9g) using 1002500 (#12 x 3/4") screws for the
latch and keeper. Using keeper as template, place
keepers as shown overhanging edge of stile, to line
up with latch slide. Mark location of mounting holes.
Secure keeper using 1002500 (#12 x 3/4").

NOTE: To ensure emergency access, locate the

keepers so that the latch slide is no more than 5/16"
(8mm) into the keeper slot as shown. (Fig. 9f).

B. Mount robe hook (Fig. 9h) using 102500 (#12 x 3/4")

screws.

C. Mount inswing door bumper (Fig. 9h) to panel or door

at location that prevents door from hitting panel on the
inswing.

Fig. 9g: Perpendicular Stile Mounting
Location of Latch Keeper.

1-1/2''

Door

C

L

2''

Stile

Panel

C

L

Fig. 9f: Mounting Location of Latch,
Keeper with Emergency Access.

C

Door

L

Door

3/4''

(19mm)

3/16''

(4mm)

7/8''

(22mm)

1-7/8''

(45mm)

28-1/6''

(710mm)

Latch

Fig. 9h: Robe Hook and Bumper.

C

Panel

L

Stile

5/16''

(8mm)

Max.

Keeper

Latch

Keeper &

Door Stop

2-1/2''

Outswing

A. Mount latches and keepers as shown (Fig. 9f, 9i) using

screws 1002500 (#12 x 3/4").

NOTE: To ensure *emergency access, locate the

keeper so the latch slide is seated no more than 5/16"
(7mm) from the top of keeper (See Fig. 9i).

B. On outswing door, install the handle on outside of

door opposite the latch. Using the door handle as a
template on the outside of door, mark location for top
hole in handle 31-5/8" (803mm) up from the bottom
edge of door. Mark location for bottom hole in handle.
Drill two (2) 3/16" (5mm) diameter holes of door
using #8-32 x 1-14" one way screws provided. For
accessible compartments, latch must also be installed

on the interior.
C. Mount robe hook 1002500 (#12 x 3/4") screws.
D. Mount outswing door bumper using 1002500 (#12 x

3/4") at location that prevents door from hitting surface

on the outswing.

Fig. 9i: Mounting Location of Latch and
Keeper with Emergency Access.

1-3/8''

(35mm)

1-7/8''

(50mm)

5/16''

(8mm)

Keeper

Latch

28-1/6''

(715mm)

1-7/8''

(50mm)

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

Page 11

1'' Thick Stile

3/16'' Wide Flange

for 1'' Thick Stile

Close

Retaining Screw

Fasten When Closed

Shoe

Trap Bottom Flange

Under Shoe Retainer

Shoe Retainer

2. Close

to Engage Retainer

1. Push on Retaining Clip
to Engage with Hole

This End to Wall

1'' Thick Stile

3/16'' Wide Flange

for 1'' Thick Stile

Shoe Retainer

Flat Washer at

Floor or Ceiling

Anchor Bolt,

Nuts & Washers

Shoe

Trap Bottom Flange

Under Shoe Retainer

INSTALL SHOESSTEP 10

A. Locate proper width shoe for stile.

B. Confirm shoe retainer (#1002413 for Overhead-Braced Series (Fig. 10) or #1002186 for Floor-Anchored or Ceiling-

Hung Series (Fig. 10) is installed on anchor bolt next to flat washer closest to floor or ceiling. For anchor assembly
detail, reference diagram on Page 4.

C. Shoes accommodate 1" thick or 3/4" thick stiles. For 1" thick stiles, orient shoe with 3/16" wide flange return against

faces and edge of stile.

D. Standard Stile Installation - See Fig. 10

Open end of shoe and slide onto bottom of stile, trapping bottom flange under shoe retainer. Close open end of shoe,

overlapping so holes are aligned. Install flat head retaining screw through double thickness of material to close shoe.

E. Remove protective covering and wipe shoe clean.

Fig. 10: Standard Stile Installation. (Overhead-Braced Anchor Shown)

REPLACEMENT SHOE GUIDE

Stile Width Bobrick Part Number Stile Width Bobrick Part Number

3" 1002175 10" 1002179

4" 1002176 12" 1002180

5" 1002184 16" 1002181

6" 1002177 18" 1002196

7" 1002197 20" 1002182

8" 1002178 24" 1002183

STEP 11

A. Remove any exposed labels from the components of toilet compartments.

FINISH AND CLEANUP

B. Clean surfaces as needed. CAUTION: Do not use cleaners containing acid on Bobrick toilet compartments.
For example, tile cleaners containing acid may attack the stainless steel hardware.
For Bobrick recommendations, refer to Bobrick Form Nos. TB-21 and TB-60.

Page 12

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.

In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.

Los Angeles: 6901 Tujunga Ave., North Hollywood, CA 91605-6213: Tel: [phone], Fax: [phone]

New York: 200 Commerce Drive, Clifton Park, NY 12065-1350; Tel: [phone], Fax: [phone],

or e-mail: [e-mail]

In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY

45 Rolark Drive, Scarborough, Ontario M1R 3B1

Eastern Canada Tel: [phone], Fax: [phone]; Western Canada Tel: ( 877) 423-6444, Fax: [phone],

or e-mail [e-mail]

Form No. 1550-69 r4/20/18 © 2018 Bobrick Washroom Equipment, Inc. Printed in U.S.A.