Bobrick KB200-00 Specifications

Koala Kare Products

A Division of Bobrick

HORIZONTAL

35''

890mm

20''

500mm

16''

405mm

WALL-MOUNTED

BABY CHANGING

STATION

KB200-00

Finish Face of Wall

4''

102mm

When Closed

CREAM

S

S

S

Recommended

44-1/4'' 1124mm

Mounting Height Off Floor

22''

550mm

w

Pneumatic Cylinder

Finish Face of Floor

ADA Compliance

(when properly installed)

4.4.1 Max. Protruding Objects

4.2.5 Forward Reach

4.2.6 Side Reach

4.27.4 Operation

Mounting Chassis

Steel-on-Steel Hinge

33''

840mm

from floor

max

22-1/8''
562mm

MATERIALS:

FDA approved injection-molded polypropylene with Microban

®

antimicrobial additive embedded into the bed surface.
Reinforced steel-on-steel hinge mechanism and metal mounting chassis with mounting hardware included. Labelled usage
instructions and safety messages in four languages. Optional Braille label available. Contoured changing surface area is
450 sq. in (11,430 sq. mm) and comes complete with nylon safety strap and bag hooks. Dual cavity liner dispenser holds
approximately 50 KB150-99 bed liners.

48'' 1219mm

For Barrier-Free Design

Recommended Mounting Height Off Floor

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. KB200-00 Issued 11/09 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2009 by Koala Kare Products, A Division of Bobrick.

continued . . .

OPERATION:

Concealed pneumatic cylinder and metal mounting chassis provides controlled, slow opening and closing of bed.
Polypropylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance
requirements when properly installed

Warning: To ensure that the unit supports the intended loads, baby changing stations must be properly installed according
to the manufacturer’s instructions.

INSTALLATION:

To ensure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting
significant weight and can accommodate the supplied installation hardware. The Koala Baby Changing Station meets ADA
regulations when properly installed.

Drilling holes and mounting the station:

1. Remove changing station from the shipping container and check for any freight damage. If damage is found, please call Koala
Kare Products' Customer Service at 888.733.3456. Remove "Installtion Kit" and "Operator Kit" from box. Please give "Operator
Kit" to facility manager or operator. Box should contain two pieces: the bed and metal mounting chassis and the wall mount liner
dispenser. Identify the best location for installing the unit.

2. Standard installation- Remove the bed and chassis from the box and select the wall area where the unit will be installed. Make
sure you have taken into consiteration the operating clearance of 9-1/2" (241.3mm) on both sides of the exposed chassis and 22"
(558.8mm) form wall surface when open. Measeure from the floor 44-1/4" (1123.95mm) on stud center and mark wall. The
mounting holes are designed for 16" stud centers. Ensure the locations you have marked for the mounting holes are level before
drilling. Drill pilot holes for keyhole mounting using a 1/8" regular drill bit.

Masonry or Tile over Stud Wall- Use a 7/32" (5.56mm) masonry drill bit for the pilot hole until you hit the stud. Change bit to
1/8" (3.18mm) regular drill bit.

Metal Stud or Concrete Block- If the wall has wood studs that are not on 16" (406.4mm) centers, has metal studs or an
underlying surface on concrete block, drill with a 1/2" (12.7mm) masonry bit. (You may have to purchase toggles before installing.)
You must allow a minimum of inside wall space for toggles to turn depending on toggles used. Insert and tighten toggles.

3. Screw two of the mounting screws into the pilot holes leaving 1/4" (6.35mm) exposed to allow keyhole slots to be easly mounted
over the screw heads. After securing the unit using the keyhole slots, verify that the unit is level. Tighten top two screws so
that they are flush with the wall. Use the four lower holes as a guide to mark and drill pilot holes. Use remaining four screws and
four washers to complete installation of bed and mounting bracket. Insert washers over lower four screws. All SIX screws and four
washers must be mounted to the chassis.

4. Ensure liner dispenser is free from damage. Remove key, unlock, and open liner dispenser lid. This will expose liner dispenser
mounting holes. Line up dispenser mounting holes onto chassis and secure with the four screws provided. Close and lock
the liner dispenser door.

5. Clean work area and inspect unit to ensure it opens and closes smoothly. Give "Operator Kit" and key to the facility operator.
Replacment parts and additional liners can be purchased from your local distributor or by calling Koala at 888.733.3456 or

303.539.8300.

SPECIFICATION:

Baby changing station body shall be durable, injection-molded polypropylene. Design of unit shall be surface-mounted.
Unit shall be equipped with a pneumatic cylinder for controlled opening and closing of bed. Bed shall be secured to metal
mounting chassis with a concealed steel-on-steel hinge. No hinge structure shall be exposed on interior or exterior surfaces.
Unit shall have mounting hardware included. Unit shall have Microban

®

antimicrobial embedded into plastic material on
the changing surface. Unit shall conform to ANSI S117.1 Accessible and Usable Building and Facilities, ASTM F 2285­04 Standard Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product
Safety Signs and Labels, EN 12221-1:2008, ASTM G22 Antibacterial standards or local code if more stringent installation
requirements are applicable for Barrier-Free accessibility. Unit shall comply with ADA regulations when properly installed.
Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses.

Unit shall have a built-in Liner Dispenser for use with 3-ply chemical free biodegradable bed liners, instructional graphics
and safety messages in 4 languages. Optional Braille label is available. Unit shall be backed by manufacturer’s 5-year
limited warranty on materials and workmanship and include a provision for replacement caused by vandalism. Unit shall be
manufactured in the U.S.A.

Baby Changing Station shall be model KB200-00 of Koala Kare Products, A Division of Bobrick, 6982 S. Quentin St.,
Centennial, CO 80112 USA, Tel: [phone] or 303-539-8359, Web: www.koalabear.com

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. KB200-00 Issued 11/09 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2009 by Koala Kare Products, A Division of Bobrick.