Bobrick KB110-SSRE User Manual
Koala Kare Products
A Division of Bobrick
HORIZONTAL
37''
939mm
32''
812mm
8.25''
210mm
23''
584mm
33''
838mm
from floor
max.
Floor
15.25''
387mm
2'' 51mm
Recommended Mounting Height Off Floor
48'' 1283mm
9.25''
235mm
8.25''
210mm
2.5''
64mm
4''
102mm
20''
508mm
Finish Face of Wall
Recommended Mounting Height Off Floor
For Barrier-Free Design
44' 1120mm
RECESSED-MOUNTED
STAINLESS STEEL FINISH
BABY CHANGING STATION
KB110-SSRE
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. KB110-SSRE Revised 1/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2006 by Koala Kare Products, A Division of Bobrick.
ADA Compliance
(when properly installed)
4.4.1 Max. Protruding Objects
4.2.5 Forward Reach
4.2.6 Side Reach
4.27.4 Operation
Rough Wall Opening
35-1/2" (900mm) wide
20-1/2" (529mm) high
4" (102mm) minimum
recessed depth
continued . . .
MATERIALS:
8-1/8''
206mm
Vertical 2 x 4’s Mounted
35-1/4'' (895mm) apart-inside
Measurement
Top Hole
44''
(1118mm)
ADA From Floor
26-1/2''
(673mm)
ADA From Top
of Stud to Floor
46-1/2''
(1181mm)
ADA From Bottom
of Stud to Floor
Rough Opening
35-1/2'' (902mm) wide
20-1/4'' (514mm) high
4'' (102mm)
minimum depth
18 gauge, type 304 satin stainless steel exterior finish with FDA approved blow molded high-density grey polyethylene
with Microban Antimicrobial additive interior. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel
mounting plates and mounting hardware included. Molded in graphics and safety messages in six languages. Contoured
changing surface area is 442 sq in (2873 sq mm) and comes complete with nylon safety straps and bag hooks.
OPERATION:
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density
polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance requirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99 sanitary liners.
Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installed according
to the manufacturer’s instructions.
INSTALLATION:
To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting
significant weight and can accommodate the supplied installation hardware. The Koala Bear Kare® Baby Changing Station
meets ADA regulations when properly installed.
Drilling holes and mounting the station:
Remove the station from the shipping container and check for any freight
1.
damage. Identify the best location for installing the baby changing
station. Hold the unit in place, open the bed, and make sure that there
is adequate operating clearance.
2. Select the wall area where the Baby Changing Station will be installed.
Measure from the floor, at the center of the stud, and mark the wall for
the appropriate height. Hold the unit in place to verify alignment. Cut an
opening in the wall 35-1/2" (900 mm) wide, 20-1/2" (529 mm) high, 4"
(102 mm) minimum depth and install framing on the top, bottom and
sides of wall opening. If the wall surface is masonry or tile over wood
studs, use caution when cutting the hole for the unit.
3. The unit will be mounted using 4-1/4'' x 1-1/2'' wood screws through the
sides of the unit into the framing of the wall opening.
4. Place the unit into the recessed wall opening and insert the screws and
flat washers to hold the Baby Changing Station in place. It may be
necessary to adjust the squareness of the door by using a shim on the
top right or left side of the unit before tightening securely to the wall.
SPECIFICATION:
Baby changing station shall have 18 gauge, type 304 satin stainless steel exterior finish with high density grey polyethylene
interior. Design of unit shall be recess-mounted. Unit shall be equipped with a pneumatic cylinder for controlled opening
and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-on-steel hinge. Unit shall have
Microban Antimicrobial embedded into plastic material. No hinge structure shall be exposed on interior or exterior surfaces.
Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shall conform to ANSI S117.1
Accessible and Usable Buildings and Facilities, ASTM F2285-04 (formerly ASTM PS125) Standard Consumer Safety
Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs and Labels,
German TUV Technical Inspection Association, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards or local
code if more stringent installation requirements are applicable for barrier-free accessibility. Unit shall comply with ADA
regulations when properly installed. Bed shall have smooth concave changing area with a nylon safety strap and two hooks
for bags or purses. Unit shall have a built-in Liner Dispenser for use with 3-ply chemical-free biodegradable sanitary liners,
universal instruction graphics, and safety messages in 6 languages. Unit shall be backed by manufacturer’s 5-year limited
warranty on materials and workmanship, and a 5-year replacement warranty against vandalism. Unit shall be manufactured
in the U.S.A.
Baby Changing Station shall be model KB110-SSRE
of Koala Kare Products, A Division of Bobrick, 6982 S. Quentin
St., Centennial, CO 80112 USA, Tel: 1-888-733-3456 or 303-539-8359, Web: www.koalabear.com
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. KB110-SSRE Revised 1/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2006 by Koala Kare Products, A Division of Bobrick.
Loading...