Bobrick BCS-1 Specifications

HORIZONTAL

Finish Face of Floor

33''

838mm

from floor

max

19.5''

495mm

Recommended Mounting Height Off Floor

For Barrier-Free Design

48'' 1219mm

Recommended Mounting Height Off Floor

45.5'' 1156mm

4''

102mm

Finish Face of Wall

35''

889mm

20''

508mm

Tel: [phone] www.gamcousa.com MADE IN U.S.A.

WALL-MOUNTED

BABY CHANGING STATION

BCS-1 for Cream Color
BCS-2 for Grey Color

BCS

w

ADA Compliance

(when properly installed)

4.4.1 Max. Protruding Objects

4.2.5 Forward Reach

4.2.6 Side Reach

4.27.4 Operation

MATERIALS:

FDA approved blow-molded high-density polyethylene. Reinforced full-length metal on metal hinge mechanism. Contoured
changing surface area is 442 sq in (2873 sq mm) and comes complete with nylon safety straps and bag hooks.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 8/6/10 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2010 by Gamco Commercial Restroom Accessories, A Division of Bobrick.

continued . . .

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density
polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance
requirements when properly installed.

Warning: To assure that the unit supports the intended loads, baby changing stations must be properly installed according
to the manufacturer’s instructions.

INSTALLATION:

To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting
significant weight and can accommodate the supplied installation hardware. The Gamco Baby Changing Station meets ADA
regulations when properly installed.

Drilling holes and mounting the station:

1. Remove the station from the shipping container and check for any freight damage. Identify the best location for
installing the baby changing station. Hold the unit in place, open the bed, and make sure that there is adequate
operating clearance.

2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of
included hardware may be required for proper installation.

3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32" stud
center. If possible, locate the wood or metal wall studs for fastening the changing station in the desired location. If
the walls do not have studs on the center as outlined, make sure at least one side of the unit is installed into the stud
Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 45.5" (1156mm)
up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole with this mark, then
use a measuring tape and level to mark the remaining three mounting holes. This will locate the bottom of the station
28" (711mm) from the floor and the top of the bed at 33" (838mm).

Using Wood Screws:

If the wall has wood studs on 16" or 32" centers, drill 1/8" pilot holes at the marks and use the four 1/4" x 3" panhead tap­ping screws with supplied washers. If the wall is masonry or tile over wood studs, use a 7/32" masonry drill until you hit the
stud, then proceed to drill 1/8" pilot holes into the studs and use the four 1/4" x 3" panhead tapping screws with supplied
washers.

Using Toggle Fasteners:

If the wall has wood studs that are not on 16" or 32" centers, has metal studs, or an underlying surface of concrete block,
drill with a 1/2" masonry bit. A minimum of 2-1/2" of inside wall space is required for toggles to turn. Insert supplied toggles
and tighten, locate station over toggles, then use supplied 1/4" x 3" Phillips Panhead machine screws with supplied washers.

SPECIFICATION:

Baby changing station body shall be durable, high-density polyethylene. Design of unit shall be surface-mounted. Unit
shall be equipped with a pneumatic cylinder for controlled opening and closing of bed. No hinge structure shall be exposed
on interior or exterior surfaces. Unit shall conform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM
F2285-04 (formerly ASTM PS125) Standard Safety Performance Specification for Diaper Changing Tables for Commercial
Use, ANSI Z535.4 Product Safety Signs and Labels, German TUV Technical Inspection Association, ASTM G21 Antifungal
and ASTM G22 Antibacterial Standards or local code if more stringent installation requirements are applicable for barrier­free accessibility. Unit shall comply with ADA regulations when properly installed. Bed shall have smooth concave changing
area with a nylon safety strap and two hooks for bags or purses. Unit shall be backed by manufacturer’s 5-year limited
warranty on materials and workmanship. Unit shall be manufactured in the U.S.A.

Baby Changing Station shall be model BCS-1 or -2 Gamco Commercial Restroom Accessories, A Division of
Bobrick, One Gamco Place, Durant, OK

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. BCS Revised 8/6/10 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2010 by GAMCO Specialty Accessories, A Division of Bobrick.