Technical Data
BOBRICK
10-7/8"
275mm
7-7/8''
200mm
S
S
1-1/2''
40mm
11''
280mm
S
S
8-13/16''
225mm
11-5/8''
295mm
1-1/16''
25mm
Wire Opening
5-1/8''
130mm
3/4''
19mm
Diameter Hole
For
Between-Wall
Wiring
5-9/16''
140mm
5/8'' x 9/16''
16 x 14mm
Opening for Surface Wiring
S
1-7/16''
35mm
S
S
4-1/2''
115mm
8-1/16''
205mm
Typ
See Table for
Recommended
Mounting
Height Off Floor
Cover
Mounting Base
Finish Face of Wall
220-240V AC, 7 Amp, 1500-1700 Watts, 50-60 Hz, Single Phase, VDE, CE marked
Patent Pending
surface-mounted
automatic
hand dryer
Model B-715E 220-240-Volt Elan™ Dr yer
C
recommended mounting heights
Children's Washrooms, ages 3-4 36'' (915mm)
Children's Washrooms, ages 5-8 40'' (1015mm)
Children's Washrooms, ages 9-12 44'' (1120mm)
Universal Design 48'' (1219mm)
c
Bottom screw hole of mounting base to finish face of floor
B-715e
International Sale Only
Not for sale in the U.S. or Canada
materials:
Cover — One-piece, deep drawn, 20-gauge (0.9mm), type-304 stainless steel with satin finish. Cover is secured to mounting base with
three flat-head stainless steel screws.
Mounting Base and Fan Housing — 5/64" (2mm) thick fire-retardant molded grey plastic with high-gloss finish. Plastic air-inlet
grille fits into bottom of mounting base. Plastic air-outlet grille is secured between fan housing and mounting base.
Motor — Maintenance-free capacitor run, external rotor motor with sealed ball bearings at both ends of drive shaft. Equipped with an
automatic thermal-overload switch.
Fan — Dynamically balanced 5-15/64" (133mm) diameter rotor centrifugal fan with multiple metallic vanes. Directs air flow from heating element at 100 cfm, mixes air to provide uniform temperature.
Heating Element — Coiled nickel-chrome heating element is protected by an automatic thermal-overload switch and thermal fuse.
Heating element, which is located on inlet side of fan, heats air without hot spots — inaccessible to vandals.
Electronic Control — Infrared sensor automatically turns dr yer on when hands are held under air-outlet opening and across path of
sensor. Remove hands from path of sensor and dryer stops. Electronic sensor has automatic shutoff approximately two minutes after
dryer turns on if an inanimate object, such as tape or chewing gum, is placed across sensor lens. After inanimate object is removed,
electronic sensor automatically resets itself and dryer operates normally.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 4/09 R/A Int'l Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
continued . . .
operation:
No-touch operation. Electronic sensor automatically turns dr yer on when hands are held under air-outlet opening and across path of
sensor. Remove hands from path of sensor and dryer stops. Dryer will not stop by itself before user is satisfied hands are dry. Dryer
operates only when actually drying hands, which saves energy and operating costs. Electronic sensor will automatically shut dryer
off two minutes after dr yer turns on if an inanimate object is placed across sensor lens. After inanimate object is removed, electronic
sensor automatically resets itself and dryer operates normally.
5-Year Limited Warranty — This warranty is limited to the repair or exchange of defective parts at the option of Bobrick. See Installation Instruction Sheet, Form No. 715-69, for full details.
installation:
Wall Preparation: Secure mounting base on wall using template provided. For masonry walls, provide four #10 expansion shields or
anchors and secure with four #10 (M4.8) sheet-metal screws (not furnished). For plaster or dr y wall construction, provide concealed
backing to comply with local building codes, then secure unit with four #10 (M4.8) round-head sheet-metal screws or 3/16" (5mm)
toggle bolts (not furnished). Provide electrical ser vice from nearest distribution panel to dr yer mounting base in compliance with local
electrical codes.
Wiring Instructions:
Live wire to terminal marked L1, and neutral wire to terminal marked N.
Notes: Electronic sensor in Elan Dryer will pick up movement within 4" (100mm) of air-outlet nozzle. Use caution when choosing location for Elan Dryer in confined areas. Consider proximity to doorways and other traffic areas.
Bobrick automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with
the operation of the automatic sensor.
For installation instructions that include step-by-step installation procedures and details of electrical service connections, see Form No.
715-69, which is packed with each shipment. This form is also available in advance upon request.
specification:
Surface-mounted hand dr yer shall have a deep-drawn, 20-gauge (0.9mm) thick, stainless steel cover with satin finish. Mounting base
and fan housing shall be fire-retardant molded grey plastic. Capacitor run, external rotor motor shall be 90 watts, sealed with ball
bearings on ends of drive shaft, and be equipped with a thermal overload switch. Centrifugal fan shall have multiple metallic vanes.
Heating element shall be located on inlet side of fan, shall heat without hot spots, be inaccessible to vandals, and protected by an
automatic thermal-overload switch and thermal fuse. Electronic sensor shall automatically turn dryer on when hands are held under
air-outlet opening and across path of sensor. Dryer shall turn of f automatically when hands are removed. Sensor shall automatically
shut dryer off approximately two minutes after dr yer turns on if an inanimate object is placed across sensor lens. After inanimate object
is removed, electronic sensor shall automatically reset itself and dryer shall operate normally. Unit shall be VDE approved, CE marked.
Unit shall comply with EU Directive “Restriction of Hazardous Substance” (ROHS) requirements for non-use of cer tain hazardous
substances in the production of electronic products. Unit shall be protected by a limited 5-year warranty on all parts. Manufacturer's
service and parts manual shall be provided to the building owner/manager upon request.
Surface-Mounted Automatic Hand Dr yer shall be Model B-715E 220-240V of Bobrick Washroom Equipment, Inc.,
Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; and Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited,
United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-715E Rev. 4/09 R/A Int'l Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
Loading...