Bobrick B-7128 User Manual

TrimLine™

SURFACE-MOUNTED

B-7120

Technical Data

Specify Voltage Required:

 B-7120 Dryer with White Painted Cover
 B-7128 Dryer with Stainless Steel Cover

Specify model number followed by voltage required. Example: B-7128 115V for 115-volt Stainless steel cover hand dryer.

ADA DRYER

Patent Pending

13-25/32" 350mm

9-1/4" 235mm

B-7128

Specify Voltage Required:

 115V AC, 15 Amp, 1725 Watts, 50/60 Hz, Single Phase, cULus Listed.
 208–240V AC, 6.8-7.8 Amp,1400-1900 Watts, 50/60 Hz, Single Phase, cULus

Listed, VDE and CCC approved, CE marked.

C

RECOMMENDED MOUNTING HEIGHTS

Children's Washrooms, ages 3-4 36'' (915mm)

Children's Washrooms, ages 5-8 40'' (1015mm)

Children's Washrooms, ages 9-12 44'' (1120mm)

Universal Design 48'' (1219mm)

c

Bottom screw hole of mounting base to finish face of floor

Finish Face of Wall

4"

100mm

S

Ø 5/16" 8mm

1. 2. 3.

x 4

Ø7/8" 22mm
Hole for between wall wiring

Hole for between wall wiring

Ø7/8" 22mm

Flange cutout for
surface mounting

S

4-1/8"

105mm

See Table for

Recommended Mounting

Height Off Floor

7-3/4" 197mm

13-19/32" 345mm

MATERIALS:

Cover — 18-gauge, Type-304 stainless steel with #4 satin-finish vertical grain (B-7128) or 22-gauge mild steel zinc plated with
high-gloss white epoxy paint finish (B-7120) covers with UL 94-5VA black plastic trim and side panels. Cover equipped with
uniquely designed dual air outlets. Air-inlet is equipped with vandal-resistant grille. Cover projects no more than 4" (100mm)
from wall and is secured to mounting base with two vandal-resistant, recessed hex screws.

Mounting Base — 20-gauge (1.5mm) plated steel with four 0.236'' (6mm) diameter mounting holes.
Motor — Universal, 1/7 hp, 8000 rpm, on resilient mounting. Sealed ball bearing at drive-shaft end and self-lubricating sleeve

bearing at nondrive end. Equipped with automatic thermal-overload switch.

Fans — Two balanced, double-inlet centrifugal fans are mounted on motor shaft; directs airflow over heating element at 71 cfm.
Heating Element — Two coiled nickel-chrome heating elements are mounted in mica frame and protected by automatic

thermal-overload switches. Heating elements, heat air without hot spots — inaccessible to vandals.
Electronic Control — Infrared sensor automatically turns dryer on when hands are held under air-outlet opening and across

path of sensor. Remove hands from path of sensor and dryer stops. Electronic sensor has automatic shutoff approximately
1-1/2 minutes after dryer turns on if an inanimate object is placed across air-outlet opening. After inanimate object is removed,
electronic sensor automatically resets itself and dryer operates normally.

continued . . .

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 9/09 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.

OPERATION:

No-touch operation: electronic sensor automatically turns dr yer on when hands are held under air-outlet opening and across
path of sensor. Dual air outlets provide a swirling circulation of airflow for comfortable hand drying. Drying time less than
25 seconds. Remove hands from path of sensor and dryer stops. Dryer operates only when actually dr ying hands, which
saves energy and operating costs. Electronic sensor will automatically shut dryer off 1-1/2 minutes after dr yer turns on if an
inanimate object, such as tape or chewing gum, is placed across air-outlet opening. After inanimate object is removed, electronic
sensor automatically resets itself and dryer operates normally.

10-Year Limited Warranty — In addition to Bobrick's one-year guarantee, Bobrick extends a limited 10-year warranty from
the date of purchase on all parts for Model B-7120 and B-7128 hand dryer, except motor brushes, to the original owner of the
installed unit against defects in factory workmanship or material under normal use and service. Motor brushes are warranted
for three years from date of purchase. This warranty is limited to the repair or exchange of defective parts at the option of
Bobrick. See Installation Instruction Sheet, Form No. 712-69, for full details.

INSTALLATION:

Wall preparation: Locate mounting base on wall using template provided. For brick, stone, and concrete walls drill four

0.315" (8mm) holes to suit provided wall plugs 0.315" (8mm) x 1-1/4" (45mm) and screws # 10 (4.8mm) x 2" (50mm) long.
See template for wall plug and screw installation details. For plaster or dry wall construction, provide concealed backing to
comply with local building codes and secure with four #10 (4.8) round-head sheet-metal screws or 3/16" (5mm) toggle bolts
(not furnished). Provide electrical ser vice from nearest distribution panel to dr yer mounting base in conformance with local
electrical codes.

Wiring Instructions:

1. For 115-Volt Dr yers — Connect ground wire to ground terminal marked , the black or hot wire to terminal marked L1,
and neutral or white wire to terminal marked N.

2. For 208–240-Volt Dr yers — Connect ground wire to ground terminal marked and the 208-240-volt wires to terminal

marked L1 and L2.
Notes: Electronic sensor in Automatic dryers will pick up movement within 6" (150mm) of the air-outlet opening. Use caution

when choosing location for Automatic dryers in confined areas. Consider proximity to doorways and other traffic areas.

Bobrick automatic hand dryers should be installed at least 15" (380mm) above any projection or horizontal surface which may
interfere with the operation of the automatic sensor.

For installation instructions that include step-by-step installation procedures and details of electrical service connections, see
Form No. 712-69, which is packed with each shipment. This form is also available in advance upon request.

SPECIFICATION:

Surface-mounted hand dryer shall have either 18-gauge, Type-304 stainless steel with #4 satin-finish vertical grain (B-7128)
or 22-gauge mild steel zinc plated with high-gloss white epoxy paint finish (B-7120) covers with UL 94-5VA black plastic trim.
Slim profile cover shall project no more than 4" (100mm) from the finished face of wall to comply with barrier-free accessibility
guidelines (including ADAAG in the U.S.A.). Unit shall be equipped with uniquely designed (patent pending) dual air outlets
that provide a swirling circulation of airflow for (less then 25 seconds) hand dry. Motor shall be 1/7 hp, universal type on
resilient mounting with sealed ball bearing at drive-shaft end and self-lubricating sleeve bearing at nondrive end; equipped with
automatic thermal-overload switch. Heating elements shall be located on outlet side of fan, shall heat air without hot spots, be
inaccessible to vandals, and protected by an automatic thermal-overload switch. Electronic sensor shall automatically turn dryer
on when hands are held under air-outlet opening and across path of sensor. Dryer shall turn off automatically when hands are
removed. Sensor shall automatically shut dryer off approximately 1-1/2 minutes after dr yer turns on if an inanimate object is
placed across air-outlet opening. After inanimate object is removed, electronic sensor shall automatically reset itself and dr yer
shall operate normally. Unit shall be

cULus Listed, and/or VDE approved, CE marked. Unit shall comply with EU Directive

"Restriction of Hazardous Substance" (ROHS) requirements for non-use of certain hazardous substances in the production of
electronic products. Unit shall be protected by a limited 10 -year warranty on all parts except motor brushes. Motor brushes
shall be warranted for three years from date of purchase.

TrimLine™ Surface-Mounted ADA Hand Dr yer shall be Model B-7120 and B-7128 of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-7120 Revised 9/09 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.