BOBRICK
AUTOMATIC HAND DRYER
1-7/16"
35mm
1-1/16"
25mm
10-15/16"
280mm
8-13/16"
225mm
1-7/16"
35mm
7-7/8"
200mm
10-13/16"
275mm
See Table
for
Recommended
Mounting
Height Off Floor
Cover
Mounting Base
Finish Face of Wall
3/4"
19mm
Diameter Hole
for Between-Wall
Wiring
5/8" x 9/16"
16 x 14mm
Opening for Surface Wiring
Wire Opening
10-15/16"
280mm
5"
125mm
5-3/16"
130mm
8-1/16"
205mm
Typ.
4-1/2"
115mm
S
S
S
SS
SS
surface-mounted
Technical Data
automatic
hand dryer
B-710
Model B-710 115-Volt CompacDr yer™
115V AC, 15 Amp, 1725 Watts, 60 Hz, Single Phase, cULus Listed
Designer's Note: Model B-710 CompacDryer™ is not designed for vandal-prone installations. For vandal-prone installations, use Bobrick
AirCraft® Dryers with cast-iron, vitreous enamel finished covers.
C
recommended mounting heights
Children's Washrooms, ages 3-4 36'' (915mm)
Children's Washrooms, ages 5-8 40'' (1015mm)
Children's Washrooms, ages 9-12 44'' (1120mm)
Universal Design 48'' (1219mm)
c
Bottom screw hole of mounting base to finish face of floor
Patented
materials:
Cover — One-piece, 3/32'' (2.6mm) thick fire-retardant, molded , high-quality, high-impact, pale grey (Bobrick color #889) ABS plastic,
5-V rated. Cover is secured to mounting base with three flat-head stainless steel screws.
Mounting Base and Fan Housing — 5-64" (2.0mm) thick fire-retardant molded grey plastic with high-gloss finish. Air-inlet grille fits
into bottom of mounting base. Air-outlet grille is secured between fan housing and mounting base.
Motor — 115V AC, 90 W, 60 Hz, 2500 rpm. Brushless, external rotor motor. Sealed ball bearings at both ends of drive shaft;
maintenance free. Equipped with an automatic thermal-overload switch.
Fan — Dynamically balanced 5-15/64" (133mm) diameter centrifugal fan with multiple metallic vanes. Directs air flow from heating
element at 90 cfm, mixes air to provide uniform temperature.
Heating Element — Coiled nickel-chrome heating element is protected by an automatic thermal-overload switch. Heating element,
which is located on inlet side of fan, heats air without hot spots — inaccessible to vandals.
Electronic Control — Infrared sensor automatically turns dr yer on when hands are held under air-outlet opening and across path of
sensor. Remove hands from path of sensor and dryer stops. Electronic sensor has automatic shutoff approximately two minutes after
dryer turns on if an inanimate object, such as tape or chewing gum, is placed across sensor lens. After inanimate object is removed,
electronic sensor automatically resets itself and dryer operates normally.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/09 R/A Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
continued . . .
operation:
No-touch operation. Electronic sensor automatically turns dr yer on when hands are held under air-outlet opening and across path of
sensor. Remove hands from path of sensor and dryer stops. Dryer will not stop by itself before user is satisfied hands are dry. Dryer
operates only when actually drying hands, which saves energy and operating costs. Electronic sensor will automatically shut dryer
off two minutes after dr yer turns on if an inanimate object is placed across sensor lens. After inanimate object is removed, electronic
sensor automatically resets itself and dryer operates normally.
1-Year Limited Warranty — This warranty is limited to the repair or exchange of defective parts at the option of Bobrick. See
Installation Instruction Sheet, Form No. 710-69, for full details.
installation:
Wall Preparation: Secure mounting base on wall using template provided. For masonry walls, provide four #10 expansion shields or
anchors and secure with four #10 (M4.8) sheet-metal screws (not furnished). For plaster or dr y wall construction, provide concealed
backing to comply with local building codes, then secure unit with four #10 (M4.8) round-head sheet-metal screws or 3/16" (5mm)
toggle bolts (not furnished). Provide electrical ser vice from nearest distribution panel to dr yer mounting base in compliance with local
electrical codes.
Wiring Instructions:
Connect ground wire to ground terminal marked , the black or hot wire to terminal marked L1, and neutral or white wire to
terminal marked N. A DEDICATED LINE IS REQUIRED FOR EACH 115-VOLT INSTALLATION.
Notes: Electronic sensor in CompacDryer will pick up movement within 4" (100mm) of air-outlet nozzle. Use caution when choosing
location for CompacDryer in confined areas. Consider proximity to doorways and other traffic areas.
Bobrick automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with
the operation of the automatic sensor.
For installation instructions that include step-by-step installation procedures and details of electrical service connections, see Form
No. 710-69, which is packed with each shipment. This form is also available in advance upon request.
specification:
Surface-mounted hand dr yer shall have a one-piece, fire-retardant molded, Bobrick grey color #889. Mounting base and fan housing
shall be fire-retardant molded grey plastic with high-gloss finish. Brushless motor shall be 90 watts, external rotor type with sealed
ball bearings on ends of drive shaft and be equipped with an automatic thermal-overload switch. Centrifugal fan shall have multiple
metallic vanes. Heating element shall be located on inlet side of fan, shall heat without hot spots, be inaccessible to vandals, and
protected by an automatic thermal-overload switch. Electronic sensor shall automatically turn dryer on when hands are held under airoutlet opening and across path of sensor. Dryer shall turn of f automatically when hands are removed. Sensor shall automatically shut
dryer off approximately two minutes after dr yer turns on if an inanimate object is placed across sensor lens. After inanimate object
is removed, electronic sensor shall automatically reset itself and dryer shall operate normally. Unit shall be cULus listed. Unit shall
comply with EU Directive “Restriction of Hazardous Substance” (ROHS) requirements for non-use of cer tain hazardous substances
in the production of electronic products. Unit shall be protected by a limited 1-year warranty on all parts. Manufacturer's ser vice and
parts manual shall be provided to the building owner/manager upon request.
Surface-Mounted Automatic Hand Dr yer shall be Model B-710 115V of Bobrick Washroom Equipment, Inc., Clifton
Park, New York; Jackson, Tennessee; Los Angeles, California; and Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-710 Rev. 4/09 R/A Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
Loading...