Technical Data
12-1/2''
320mm
Finish Face of Wall
3-5/16''
85mm
Concealed
Wall Plate
S
1/2''
13mm
2''
50mm
Typ.
S
Flange and
Mounting Bracket
Support Arm
3-15/16''
100mm
2''
50mm
Typ.
5-1/4''
135mm
5-1/4''
135mm
Setscrew
Recommended Mounting Height Off Floor
For Universal / Barrier-Free Design
20''
510mm
DOubLE-ROLL
TOILET TISSuE
DISPENSER
b-686
b-6867
Specify Model Required:
Model B‑686 Bright polished stainless steel
Model B‑6867 Satin‑finish stainless steel
MATERIAL:
Flanges and Support Arms (3) ‑— 18‑8 S, type‑304, 22‑gauge (0.8mm) stainless steel. Concealed, 16‑gauge (1.6mm) stainless
steel mounting bracket is welded inside each flange. Secured to wall plate with setscrew.
Concealed Wall Plates (3) — 18‑8 S, type‑304, 16‑gauge (1.6mm) stainless steel.
Spindles (2) — Chrome‑plated plastic. Equipped with heavy‑duty internal springs.
Designer's Note: Theft‑resistant spindles, which are removable only with special key provided, are available as optional
accessories. To specify, add suffix .60 to model number. Example B‑686.60.
INSTALLATION:
To remove concealed wall plates from back of flanges and mounting brackets, loosen setscrews. Mount each wall plate with
prongs at top; secure with sheet‑metal screws furnished by manufacturer at points indicated by an S. Engage mounting
brackets onto prongs of wall plate, then secure into position by tightening setscrews at bottom of flanges.
Note: Center‑to‑center of concealed wall plates must be within 1/16'' (1.6mm) of dimension shown.
For partitions with par ticle‑board or other solid core: Secure with sheet‑metal screws furnished by manufacturer or provide
through‑bolts, nuts, and washers.
For hollow‑core metal partitions: Provide solid backing into which the furnished sheet‑metal screws can be secured. If two units
are installed back‑to‑back, then provide threaded sleeves and machine screws for the full thickness of partition.
For masonry walls: Provide fiber plugs or expansion shields for use with sheet‑metal screws furnished by manufacturer, or
provide 1/8'' (3mm) toggle bolts or expansion bolts.
For plaster or dry wall construction: Provide concealed backing to comply with local building codes, then secure the unit with
sheet‑metal screws furnished.
SPECIFICATION:
Double‑roll toilet tissue dispenser shall be type‑304 stainless steel with _______________ (insert one: bright polished or satin)
finish. Unit shall accommodate two standard‑core toilet paper rolls up to 5‑1/2'' (140mm) diameter (1800 sheets). Flanges shall
be equipped with concealed, 16‑gauge (1.6mm) stainless steel mounting brackets that are secured to concealed stainless steel
wall plates with stainless steel setscrews. *Spindles shall be equipped with a heavy‑duty internal spring. Manufacturer's ser vice
and parts manual shall be provided to the building owner/manager upon request.
*To specify theft-resistant spindles as an optional accessory, add to specification: Theft‑resistant spindles shall be removable only
with special key provided.
Double-Roll Toilet Tissue Dispenser shall be Model ________________ (insert model number) of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 6/06 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2006 by Bobrick Washroom Equipment, Inc.
Loading...