Bobrick B-541 User Manual

SPARE

Technical Data

TOILET ROLL

HOLdER

180mm

7''

Shelf
Plate

Mounting

S

35mm

1-5/16''

S

1-3/16'' Dia.

Flange

Finished Face of Wall

130mm
5-1/16''

Flange

45mm

Cover

B-541

Tube

55mm
2-1/8''

30mm

1-1/8'' R

50mm

1-15/16''

15mm

65mm
2-1/2''

1/2''

MATERIAL:

Toilet Roll Holder -— 18-8 S, type-304, 0.9mm (20-gauge) stainless steel tubing with satin-finish. 19mm (3/4") outside
diameter. End is welded to Concealed Mounting Threaded Flange. Clearance between the toilet tissue bar and the wall is 55mm
(2-1/8").

Concealed Mounting Threaded Flange — 18-8 S, type-304, 5.6mm (7/32") thick, stainless steel plate with thread on outside
edge for fastening cover. 46mm (1-13/16") outside diameter with two holes for attachment to wall.

Threaded Flange Cover — 18-8 S, type-304, 1.4mm (17-gauge), machined stainless steel with satin-finish. 49mm (1-15/16")
diameter 13mm (1/2") deep. Cover fastens over mounting flange to conceal mounting screws.

Shelf Plate — 18-8 S, type-304, 3mm (1/8") thick x 49mm (1-15/16") diameter stainless steel plate with satin-finish. Inside
diameter edge is welded to toilet tissue bar to hold toilet tissue roll.

INSTALLATION:

For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with
sheet-metal screws (not furnished). For other wall sur faces, provide fiber plugs or expansion shields for use with sheet-metal
screws (not furnished), or provide 3mm (1/8'') toggle bolts or expansion bolts.

For partitions with par ticle-board or other solid core, secure with sheet-metal screws (not furnished), or provide through-bolts,
nuts, and washers. For hollow-core metal partitions, provide solid backing into which the sheet-metal screws (not furnished)
can be secured.

SPECIFICATION:

Spare toilet roll holder shall be type-304 stainless steel with satin-finish. Toilet roll holder shall have 0.9mm (20-gauge) wall
thickness and 19mm (3/4") outside diameter. Clearance between the toilet roll holder and wall shall be 55mm (2-1/8'').
Concealed mounting flange shall be 5.6mm (7/32") thick stainless steel plate, 46mm (1-13/16") outside diameter and equipped
with two screw holes for attachemnt and thread on outside edge to fasten cover. Threaded flange cover shall be 1.4mm
(17-gauge) stainless steel, 49mm (1-15/16") diameter and shall fasten over mounting flange to conceal mounting screws. End
of toilet roll holder shall pass through flange and be welded to form one structural unit. Shelf plate shall be 3mm (1/8") thick
stainless steel plate, 49mm (1-15/16") outside diameter and 19mm (3/4") inside diameter. Toilet roll holder shall pass through
shelf plate and be welded to form a solid base.

Spare Toilet Roll Holder shall be Model B-541 of Bobrick Washroom Equipment, Inc., Clifton Park, New York;
Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario;
Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 3/09 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.