Bobrick B-5050 Technical data

MatrixSeries™

BO B R IC K

Patented

SURFACE-MOUNTED

SOAP DISPENSER

8-1/16''

205mm

15/16''

24mm

S

2-31/32''

75mm

3-13/16''

95mm

BOBRICK
BOBRICK

S

S

5-15/16''

150mm

Keyhole

Slot Mounting

Holes (2)

Swing-Up

Container

Push Button

Valve

Finish Face of Wall

Lid

B-5050

3-3/4''

95mm

4"

100mm

S

S

5/8''

16mm

S

Latches

7/16''

11mm

3/16''

5mm

51'' 1295mm

For Universal / Barrier-Free Design

Recommended Mounting Height Off Floor

MATERIAL:

Valve — Durable, high-impact grey ABS push button and spout with high-gloss finish on exposed surfaces. Soap head­holding capsule valve. Stainless steel spring. U-packing seal and duckbill.

Container — Durable, impact-resistant grey polymer with high-gloss finish on exposed surfaces. Equipped with a concealed
locking device to secure lid; keyed like other Bobrick washroom accessories. Front of container has same degree of arc as
front of lid and other Bobrick MatrixSeries washroom accessories. Radius on corners and edges of container complement
corners and edges of lid and other MatrixSeries accessories. Capacity: 50-fl oz (1.5-L).

Lid — Durable, impact-resistant grey polymer with high-gloss finish on exposed surfaces. Front of lid has same degree of
arc as front of container and other Bobrick MatrixSeries washroom accessories. Radius on corners, edges and top of lid
complement corners and edges of container and other Matrix Series accessories.

OPERATION:

Corrosion-resistant valve dispenses commercially marketed all-purpose hand soaps. Valve is operable with one hand, without
tight grasping, pinching, or twisting of the wrist, and with less than 5 pounds of force (22.2 N) to comply with barrier-free
accessibility guidelines (including ADAAG in U.S.A.).

INSTALLATION:

Provide (3) #10 x 1-1/2" (4.8 x 38mm) sheet-metal mounting screws to mount the container on wall at points indicated by an
S. For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with
sheet-metal screws. For other wall surfaces, provide fiber plugs or expansion shields for use with sheet-metal screws, or
provide 1/8" (3mm) toggle bolts or expansion bolts. For mirrors or glass surfaces, use pressure-sensitive tape strips
furnished by manufacturer: clean glass, apply both tape strips horizontally to back of container, press container onto glass
surface, then allow the tape to set 24 hours before filling with soap.

continued . . .

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2007 by Bobrick Washroom Equipment, Inc.

To fill container, push furnished key down into slot at back of lid and lift off lid. To close the lid, hook bottom front of lid into
recessed area located inside top front of container and rotate back of lid toward container. A snap will be heard when the lid
is locked.

Note: Mount dispenser plumb and true with valve 6" (150mm) to right or left of lavatory center. Provide 6" (150mm)
minimum clearance from lid to underside of any horizontal projection for top filling. Push buttons should be located 44"
(1120mm) maximum above the finish floor.

SPECIFICATION:

Soap dispenser shall have durable, high-impact grey ABS valve. Container and lid shall be durable, impact-resistant grey
polymer. All exposed surfaces shall have high-gloss finish. Vandal-resistant lid shall be secured to container with a concealed
locking device keyed like other Bobrick washroom accessories. Lid shall pivot up from rear for top filling only after lock is
disengaged with key provided. Front of soap dispenser shall have same degree of arc as other Bobrick MatrixSeries™
accessories in the washroom. Radius on corners, edges and top of dispenser shall complement other Bobrick MatrixSeries™
washroom accessories. Corrosion-resistant valve shall have soap head-holding capsule valve, stainless steel spring, U­packing seal, and duckbill; and shall dispense commercially marketed all-purpose hand soaps. Valve shall be operable with
one hand and with less than 5 pounds of force (22.2 N) to comply with barrier-free accessibility guidelines (including
ADAAG in U.S.A.). Container shall have a minimum capacity of 50-fl oz (1.5-L). Replacement part numbers shall be molded
into unit. Manufacturer's service and parts manual shall be provided to the building owner/manager upon request.

Soap Dispenser shall be Model B-5050 of Bobrick Washroom Equipment, Inc., Clifton Park, New York;
Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario;
Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United
Kingdom.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-5050 Revised 4/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2007 by Bobrick Washroom Equipment, Inc.