Technical Data
56-1/4''
1430mm
5-7/16''
140mm
Typ.
TowelMate
Towel Guide
Bracket Return
ConturaSeries
®
RECESSED PAPER TOWEL
DISPENSER AND WASTE
RECEPTACLE
Finish Face of Wall
17-7/16''
445mm
S
S
1/4''
6mm
Typ.
Stainless
Steel Door
Flush
Lock & Key
B-43944
3''
75mm
Typ.
1-3/4''
45mm
19''
485mm
3-15/16''
100mm
S
TowelMate
Towel Rod
S
15-5/16''
390mm
Recessed Cabinet
S
PaperTowel
Dispenser
Removable
LinerMate Trash
Liner Holder
3-1/16''
80mm
Typ.
Removable
Front Panel
26''
660mm
5''
125mm
S
1/8''
3mm
54-1/8''
1375mm
Recommended Mounting Height Off Floor
2-15/16''
75mm
Typ.
Rough Wall Opening
For Barrier-Free Design
66'' to 73'' 1675 to 1855mm
Recommended Mounting Height Off Floor
16" (405mm) wide
54-3/4" (1390mm) high
4" (100mm) minimum
MATERIALS:
recessed depth
Cabinet — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel. All-welded construction. Exposed sur faces have satin-finish.
Flange — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin-finish. Drawn, one-piece, seamless construction. Radius
on corners and return edges complement corners and edges of door and waste receptacle.
Door — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin-finish. Drawn, one-piece, seamless construction. Front of
door has same degree of arc as front of waste receptacle and other Bobrick ConturaSeries washroom accessories. Radius on
corners and edges of door match side edges of waste receptacle and other ConturaSeries accessories. Secured to cabinet with
a full-length stainless steel piano-hinge. Equipped with a stainless steel cable door-swing limiter and flush tumbler lock keyed
like other Bobrick washroom accessories.
Paper Towel Dispenser — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin-finish. Cabinet inside equipped with
90° return towel guide angle to prevent paper towels from falling forward out when door is opened for ser vicing. Rounded
towel tray has hemmed opening to dispense paper towels without tearing. Unit equipped with TowelMate consisting of a 90°
return towel guide angle inside cabinet to prevent paper towels from falling forward out when door is opened for ser vicing and
a Nylon Rod across the center of the towel tray to dispense paper towels one at a time. Waste receptacle shall have a formed,
18-gauge (1.2mm), one-piece, seamless, removable front panel with top edge hemmed. Capacity: 600 C-fold or 800 multifold
paper towels.
TowelMate™ Towel Rod Assembly — Consisting of a round Nylon Rod and (2) stainless steel Rod Screws for attachment, is
field replaceable. Stainless steel Stop Screws (2) lock TowelMate Towel Rod assembly in place.
To retrofit TowelMate into existing installed units manufactured prior to April 2010, order TowelMate Accessory Bobrick Par t
No. 3944-130
60-1/4'' 1530mm
continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 11/19/10 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2010 by Bobrick Washroom Equipment, Inc.
Waste Receptacle — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin-finish. Formed, one-piece, seamless
construction. Removable front panel has same degree of arc as front of paper towel dispenser door and other Bobrick
ConturaSeries washroom accessories. Top edge hemmed for safe handling. Radius on side edges of waste receptacle match
corners and edges of door and other ConturaSeries accessories. Secured to cabinet with two keyholes over studs on bottom and
two tamper-resistant setscrews on top. Capacity: 15.0-gal. (56.8-L).
LinerMate™ Trash Liner Holder — Unit equipped with LinerMate trash liner holder fabricated with molded plastic trash
liner holder sleeve and a 20-gauge (0.91mm), U-shaped support strap; riveted constr uction. Liner holder shall have an arc at
front and same shape as inside of waste receptacle area. LinerMate facilitates installation and removal of disposable trash liners
and retains liner inside waste receptacle.
To retrofit LinerMate into existing installed units manufactured prior to December 2009, order LinerMate Accessory Bobrick
Part No. 43944-134
OPERATION:
Paper towel dispenser will dispense C-fold or multifold paper towels without adjustment or use of adapters. Cable door-swing
limiter prevents damage to washroom accessories and walls. Load paper towels in towel tray, and then pull one sheet of paper
towel over the TowelMate towel rod and out to conceal rod and start dispense. Front of waste receptacle panel is removable for
cleaning cabinet interior. To insert disposable trash liner, lift LinerMate trash liner holder up and forward and rest over edge of
waste receptacle front panel with the bottom notches of LinerMate engaged on top front edge of receptacle. Place disposable
trash liner inside LinerMate and fold disposable trash liner over molded sleeve. Tie a knot in the corner of the disposable
trash liner, then place LinerMate with disposable trash liner back into receptacle. To empty, gather disposable trash liner from
LinerMate liner holder sleeve and lift disposable trash liner up.
INSTALLATION:
Provide framed rough wall opening 16" wide x 54-3/4" high (405 x 1390mm). Minimum recessed depth required to finish
face of wall is 4" (100mm). Allow clearance for construction features that may protrude into rough wall opening from opposite
wall. Coordinate with mechanical engineer to avoid pipes, vents, and conduits. If unit projects above top of wainscot, provide
aluminum channel or other filler to eliminate gap between flange and finish face of wall. Mount unit in wall opening with
shims between framing and cabinet at all points indicated by an S, then secure unit with #8 x 1-1/4" (4.2 x 32mm) screws (not
furnished).
SPECIFICATION:
Recessed paper towel dispenser and waste receptacle shall be type-304 stainless steel with all-welded construction; exposed
surfaces shall have satin-finish. Front of paper towel dispenser door and waste receptacle shall have same degree of arc and
match other Bobrick ConturaSeries accessories in the washroom. Radius on corners and edges of flange, door, and waste
receptacle shall complement other Bobrick ConturaSeries washroom accessories. Flange shall be drawn, one-piece, seamless
construction. Paper towel dispenser door shall be drawn, 18-gauge (1.2mm), one-piece, seamless construction; secured to
cabinet with a full-length stainless steel piano-hinge; and equipped with a stainless steel cable door-swing limiter and flush
tumbler lock keyed like other Bobrick washroom accessories. Paper towel dispenser shall dispense 600 C-fold or 800 multifold
paper towels. Unit equipped with TowelMate consisting of a 90° return towel guide angle inside cabinet to prevent paper towels
from falling forward out when door is opened for servicing and a Nylon Rod across the center of the towel tray to dispense
paper towels one at a time. Waste receptacle shall have a formed, 18-gauge (1.2mm), one-piece, seamless, removable front panel
with top edge hemmed. Unit equipped with LinerMate trash liner holder fabricated with molded plastic trash liner holder sleeve
and a 20-gauge (0.91mm), U-shaped support strap; riveted constr uction. Liner holder shall have an arc at front and same shape
as inside of waste receptacle area. LinerMate facilitates installation and removal of disposable trash liners and retains liner
inside waste receptacle. Capacity of waste receptacle shall be 15.0-gal. (56.8-L).
Recessed Paper Towel Dispenser And Waste Receptacle shall be Model B-43944 of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-43944 Rev. 11/19/10 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2010 by Bobrick Washroom Equipment, Inc.
Loading...