
SOAP DISPENSER FOR
Technical Data
LIQUID AND LOTION
SOAPS, AND DETERGENTS
Concealed
Locking
Device
S
6-3/8''
160mm
4-1/8''
105mm
S
9/16''
14mm
5-13/16''
145mm
2-1/8''
55mm
Typ.
6-7/8''
175mm
13/16''
20mm
Typ.
Container
Push Button
Valve
Finish Face of Wall
Swing-Up
Lid
3-3/8''
85mm
B-42
S
9-1/8''
230mm
Wall
Bracket
S
1/2''
13mm
50'' 1270mm
For Universal / Barrier-Free Design
Recommended Mounting Height Off Floor
MATERIAL:
Valve — Black, high-impact-resistant ABS push button and spout. Soap head-holding mushroom valve. Stainless steel spring. U-packing seal
and duckbill.
Wall Bracket — Black, high-impact-resistant ABS. Equipped with a concealed locking device to secure the lid and a removable plastic key to
disengage locking device.
Container — Black, translucent ABS. Capacity: 40-fl oz (1.2-L).
Lid — Black, high-impact-resistant ABS.
OPERATION:
Corrosion-resistant valve dispenses commercially marketed all-purpose hand soaps. Valve is operable with one hand, without tight grasping,
pinching, or twisting of the wrist, and with less than 5 pounds of force (22.2 N) to comply with barrier-free accessibility guidelines (including
ADAAG in U.S.A.). Large-capacity, translucent container provides visible soap level. To fill container, use the plastic key provided or any small
pointed object to push in the concealed locking device located at upper left side of wall bracket; lid will automatically pop forward. Lid swings
up to top fill only after lock is disengaged. After filling, swing lid down and push it toward the wall; a click sound confirms lid is locked. Soap
container is removable for maintenance or replacement by opening the lid, pushing back on the container stop spring tab and sliding the
container up off the wall bracket. Replace the lid before mounting the container onto the wall bracket.
INSTALLATION:
Remove plastic key from wall bracket. Provide (3) #10 x 1-1/2" (M5 x 38mm) mounting screws to mount the wall bracket on wall at points
indicated by an S. For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with
screws. For other wall surfaces, provide fiber plugs or expansion shields with screws, or provide 1/8" (3mm) toggle bolts or expansion bolts.
For mirrors or glass sur faces, use pressure-sensitive tape strips furnished by manufacturer: Apply tape to back of wall bracket within outlined
areas; press wall bracket onto glass surface; then allow the tape to set 24 hours before mounting the container and filling with soap. Hold lid
upright in-line with wall bracket and slide its two pivot points into upper left and right slots of wall bracket; a click sound will be heard when lid
is properly in place. With lid in the upright (open) position, slide container down into the wall bracket’s V-shaped groove. Swing lid down and
push it toward the wall; a click sound confirms lid is locked.
Note: Provide 4" (100mm) minimum clearance from lid to underside of any horizontal projection for top filling and 5" (125mm) minimum
clearance to the left of unit for disengaging the concealed locking device. Push buttons should be located 44" (1120mm) maximum above the
finish floor.
SPECIFICATION:
Soap dispenser shall have black, high-impact-resistant ABS wall bracket, lid, push button, and spout. Bracket shall be equipped with a locking device
to secure lid, container, and a removable plastic key to disengage locking device. Vandal-resistant lid shall pivot up for top filling only after lock is
disengaged. Corrosion-resistant valve shall have soap head-holding mushroom valve, stainless steel spring, U-packing seal, and duckbill; and shall
dispense commercially marketed all-purpose hand soaps. Valve shall be operable with one hand and with less than 5 pounds of force (22.2 N) to
comply with barrier-free accessibility guidelines (including ADAAG in U.S.A.). Container shall be black, translucent ABS with a capacity of 40-fl oz
(1.2-L), be retained to the wall bracket by a sliding latch and a container stop spring tab and shall be removable for maintenance or replacement.
Soap Dispenser shall be Model B-42 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los
Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd.,
Australia; and Bobrick Washroom Equipment Limited, United Kingdom.
S/D
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 2/1/11
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2011 by Bobrick Washroom Equipment, Inc.
QA013111
Printed in U.S.A.