ClassicSeries™
PARTITION-MOUNTED
SEAT-COVER DISPENSER,
SANITARY NAPKIN DISPOSAL,
Technical Data
Mounts in partition of barrier-free toilet compartment for physically disabled persons.
One side is flush against partition to allow clearance for grab bar across front of unit.
MATERIALS:
Cabinet — 18-8 S, type-304, heavy-gauge stainless steel. All-welded construction. Exposed sur faces have satin finish.
Equipped with a plastic sight-barrier panel for the toilet-seat-cover dispenser.
Flanges (2) — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn and beveled, one-piece, seamless
construc tion.
Door & Permanent Panel — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. One-piece, seamless
construction. Door is secured to cabinet with a full-length stainless steel piano-hinge and equipped with two tumbler locks
keyed like other Bobrick washroom accessories.
Toilet Tissue Dispensers (4) — .100" (2.5mm) thick ABS. Equipped with four theft-resistant, heavy-duty, one-piece, molded
ABS spindles.
Disposal Panels (2) — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with hemmed edges; exposed surface has satin
finish. Secured to cabinet with spring-loaded, full-length stainless steel piano-hinge. Equipped with international graphic
symbols identifying napkin disposal.
Waste Receptacle — Leak-proof molded polyethylene. Removable for servicing. Capacity: 0.8-gal. (3.0-L).
AND TOILET TISSUE DISPENSER
(Serves Two Toilet Compartments)
17-3/16''
435mm
6''
150mm
S
19-5/8''
500mm
30-5/8''
780mm
S
5''
125mm
15-3/16''
385mm
3-7/8''
98mm
C
Centerline of Toilet Tissue Dispenser
shall be 7'' to 9'' (180 to 230mm)
L
in Front of Toilet
16-1/16''
410mm
11-5/16''
287mm
9/16''
14mm
Toilet-Seat-Cover
Dispenser (2)
S
Sight-Barrier
Sanitary Napkin
Disposal Panel (2)
Toilet Tissue
Dispenser (4)
S
Removable
Waste Receptacle
1''
25mm
Ty p.
Fixed Flange
(Barrier-Free
Compartment)
Panel
Grab Bar
(Not Furnished)
Permanent
Panel
S
33''
840mm
to
Floor
S
B-3571
4-5/16''
110mm
Adjustable Flange
Door
S
Lock
& Key
28-5/8''
725mm
S
Lock
1/2'' to 3-7/8''
13 to 98mm
Rough Partition Cutout
15-1/2'' (395mm) wide
28-7/8'' (735mm) high
1/2" to 3-7/8'' (13 to 98mm)
partition thickness
1075mm
42-1/4''
For Universal / Barrier-Free Design
Recommended Mounting Height Off Floor
OPERATION:
Toilet-seat-cover dispenser is serviced from one side and holds 1000 single- or half-fold paper covers. Door unlocks with key
provided and swings open for filling. Spindles may be removed from cabinet when door is open; when door is closed, removal
requires a special key provided for the concealed locking mechanism in spindles. Receptacle is removable from one side of
unit for servicing. Unit holds four standard-core toilet tissue rolls up to 5-1/4" (135mm) diameter (1800 sheets), two for each
compartment.
Designer's Note: It is recommended that one full toilet tissue roll remain wrapped until the other roll has been depleted to avoid
wasting ends of both rolls. Disposable liners are available as an accessory for sanitary napkin disposal: order Bobrick Par t No.
353-12.
continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 1/6/11
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2011 by Bobrick Washroom Equipment, Inc.
R/A, S/C
Printed in U.S.A.
INSTALLATION:
Mount unit in toilet partition 1/2'' to 3-7/8'' (13 x 98mm) thick, centered through a cutout specially ordered from partition
manufacturer or field cut. Dimensions of cutout are to be 15-1/2" wide x 28-7/8" high (395 x 735mm). Top of cutout should
be 42-1/4" (1075mm) from finish face of floor to allow placement of horizontal grab bar at 33" (840mm) height across front of
unit. For factory-made cutouts, location and size details must be furnished to partition manufacturer. For hollow-core metal
partitions, provide solid framing into which sheet-metal mounting screws can be secured.
For installation with sheet-metal screws furnished, place unit firmly in partition cutout, making certain entire perimeter of fixed
flange is flush with and tight against partition sur face. Install the unit so the side that has the fixed flange flush with face of
cabinet is in a barrier-free compar tment for physically disabled persons. Secure to partition with sheet-metal screws through
four mounting holes in fixed flange at points indicated by an S. On other side of partition, position adjustable flange (which
serves as an escutcheon) so mounting holes are not inline with mounting holes in fixed flange. Make certain entire perimeter of
adjustable flange is flush with and tight against partition sur face before securing with sheet-metal screws furnished.
For through-bolting method of installation, make sure mounting holes in adjustable flange are inline with holes in fixed flange.
Using adjustable flange as template to mark locations, drill 7/32" or 1/4" (5.5 or 6.4mm) holes through partition. Provide
four binder posts and #6 (3.5mm) flat-head screws to secure unit and its adjustable flange. Obtain binder posts and screws by
ordering Bobrick Binder Post Kit No. 354-119 for partitions 1/2" (13mm) thick only or Kit No. 354-124 for partitions 3/4" to
1-1/4" (19 to 32mm) thick.
Note: Cutouts in Bobrick toilet partitions can be pre-cut for Bobrick partition-mounted accessories at factory if location and size
of cutouts are specified and order for both partitions and accessories are received together.
Designer's Note: on left side of toilet (when seated on toilet) rear edge of panel cut-out should be 32-1/2" to 34-1/2" (825 to
876mm from rear edge of panel to position toilet tisue dispensers centerline 7" to 9" (180 to 230mm) in front of leading edge of
toilet. For units on right side of toilet, rear edge of panel cut-out should be 25" to 27" (635 to 685mm) from rear edge of panel.
Cut-out locations based on toilet projecting 30" (760mm) from rear wall, and a 1/2" (13mm) gap between rear edge of panel and
rear wall
SPECIFICATION:
Partition-mounted seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be type-304 stainless steel
with all-welded construction; exposed sur faces shall have satin finish. Toilet tissue dispenser shall be ABS plastic. Flanges shall
be drawn and beveled, one-piece, seamless construction. Unit shall mount in par tition and serve two toilet compartments. One
side of unit shall mount flush against partition of barrier-free compartment to allow clearance for grab bar across front of unit.
Door shall be one-piece, seamless construction; secured to cabinet with a full-length stainless steel piano-hinge; and equipped
with two tumbler locks keyed like other Bobrick washroom accessories. Self-closing disposal panels shall be secured to cabinet
with spring-loaded, full-length stainless steel piano-hinges have hemmed edges and equipped with international graphic
symbols identifying napkin disposal. Napkin disposal shall be furnished with a removable, leak-proof, molded polyethylene
receptacle with a capacity of 0.8-gal. (3.0-L). Toilet-seat-cover dispenser and sanitary napkin disposal shall be ser viced from one
side only. Toilet-seat-cover dispenser shall be equipped with a plastic sight-barrier panel and hold 1000 paper covers. Unit shall
be equipped with four theft-resistant, heavy-duty ABS toilet tissue spindles that hold standard-core rolls up to 5-1/4" (135mm)
diameter (1800 sheets). Spindles shall be removable from cabinet when door is open; when door is closed, removal shall require
a special key provided for the concealed locking mechanism in spindles.
Partition-Mounted Seat-Cover Dispenser, Sanitar y Napkin Disposal, And Toilet Tissue Dispenser shall be Model
B-3571 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jack son, Tennessee; Los Angeles,
California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty.
Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.
R/A, S/C
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-3571 r1/6/11
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2011 by Bobrick Washroom Equipment, Inc.
QA010711
Printed in U.S.A.
Loading...