Bobrick B-357 User Manual
Technical Data
16-1/16''
410mm
17-3/16''
435mm
9/16''
14mm
Lock
19-5/8''
500mm
30-5/8''
780mm
S
S
5''
125mm
6''
150mm
15-3/16''
385mm
11-5/16''
285mm
Lock & Key
Centerline of
Toilet Tissue Dispenser
shall be 7'' to 9'' (180 to 230mm)
in Front of Toilet
1''
25mm
Typ.
3-7/8''
100mm
S
S
Toilet-Seat-Cover
Dispenser (2)
Sight-Barrier
Panel
Toilet Tissue
Dispenser (4)
S
S
1/2'' to 2''
13 to 51mm
Fixed Flange
S
S
Permanent
Panel
28-5/8''
725mm
Recommended Cutout Height Off Floor
59''
1500mm
Adjustable Flange
1-5/8''
40mm
4-5/16''
110mm
Door
Removable
Waste Receptacle
Sanitary Napkin
Disposal Panel (2)
C
L
ClassicSeries™
PARTITION-MOuNTEd
SEAT-COvER dISPENSER,
SANITARy NAPkIN dISPOSAL,
ANd TOILET TISSuE dISPENSER
(SERvES TwO TOILET COMPARTMENTS)
B-357
Rough Partition Cutout
15-1/2'' (395mm) wide
28-7/8'' (735mm) high
1/2" to 2'' (13 to 51mm)
partition thickness
MATERIALS:
Cabinet — 18-8 S, type-304, heavy-gauge stainless steel. All-welded construction. Exposed sur faces have satin finish.
Equipped with a plastic sight-barrier panel for toilet-seat-cover dispenser.
Flanges (2) — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn and beveled, one-piece, seamless
construc tion.
Door & Permanent Panel — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. One-piece, seamless
construction. Door is secured to cabinet with a full-length stainless steel piano-hinge and equipped with two tumbler locks
keyed like other Bobrick washroom accessories.
Toilet Tissue Dispensers (4) — .100" (2.5mm) thick ABS. Equipped with four theft-resistant, heavy-duty, one-piece, molded
ABS spindles.
Disposal Panels (2) — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with hemmed edges; exposed surface has satin
finish. Secured to cabinet with spring-loaded, full-length stainless steel piano-hinge. Equipped with international graphic
symbols identifying napkin disposal.
Waste Receptacle — Leak-proof molded polyethylene. Removable for servicing. Capacity: 0.8-gal. (3.0-L).
OPERATION:
Toilet-seat-cover dispenser is serviced from one side and holds 1000 single- or half-fold paper covers. Door unlocks with
key provided and swings open for filling. Spindles may be removed from cabinet only when door is open. Receptacle is
removable from one side of unit for servicing. Unit holds four standard-core toilet tissue rolls up to 5-1/4'' (135mm) diameter
(1800 sheets), two for each compartment.
Designer's Note: It is recommended that one full toilet tissue roll remain wrapped until the other roll has been depleted to avoid
wasting ends of both rolls. Disposable liners are available as an accessory for sanitary napkin disposal: order Bobrick Part No.
353-12.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 11/08 R/A, S/F Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.
continued . . .
INSTALLATION:
Mount unit in toilet partition 1/2'' to 2'' (13 x 51mm) thick, centered through a cutout specially ordered from partition
manufacturer or field cut. Dimensions of cutout are to be 15-1/2" wide x 28-7/8" high (395 x 735mm). For factory-made
cutouts, location and size details must be furnished to partition manufacturer. For hollow-core metal partitions, provide solid
framing into which mounting screws can be secured.
For installation with sheet-metal screws furnished, place unit firmly in partition cutout, making certain entire perimeter of
fixed flange is flush with and tight against partition sur face. Secure to partition with sheet-metal screws through four mounting
holes at points indicated by an S. On other side of partition, position adjustable flange (which ser ves as an escutcheon) so
mounting holes are not inline with mounting holes in fixed flange. Make certain entire perimeter of adjustable flange is flush
with and tight against partition sur face before securing with sheet-metal screws furnished.
For through-bolting method of installation, make sure mounting holes in adjustable flange are inline with holes in fixed flange.
Using adjustable flange as template to mark locations, drill 7/32" or 1/4" (5.5 or 6.4mm) holes through partition. Provide
four binder posts and #6 (3.5mm) flat-head screws to secure unit and its adjustable flange. Obtain binder posts and screws by
ordering Bobrick Binder Post Kit No. 354-119 for partitions 1/2" (13mm) thick only or Kit No. 354-124 for partitions 3/4" to
1-1/4" (19 to 32mm) thick.
Note: Cutouts in Bobrick toilet partitions can be pre-cut for Bobrick partition-mounted accessories at factor y if location and
size of cutouts are specified and order for both partitions and accessories are received together.
SPECIfICATION:
Partition-mounted toilet-seat-cover dispenser, sanitary napkin disposal, and toilet tissue dispenser shall be type-304 stainless
steel with all-welded construction; exposed sur faces shall have satin finish. Toilet tissue dispenser shall be ABS plastic.
Flanges shall be drawn and beveled, one-piece, seamless construction. Unit shall mount in par tition and serve two toilet
compartments. Door shall be one-piece, seamless constr uction; secured to cabinet with a full-length stainless steel pianohinge; and equipped with two tumbler locks keyed like other Bobrick washroom accessories. Self-closing disposal panels
shall be secured to cabinet with spring-loaded, full-length stainless steel piano-hinges, have hemmed edges and equipped with
international graphic symbols identifying napkin disposal. Napkin disposal shall be furnished with a removable, leak-proof,
molded polyethylene receptacle with a capacity of 0.8-gal. (3.0-L). Toilet-seat-cover dispenser and sanitary napkin disposal
shall be serviced from one side only. Toilet-seat-cover dispenser shall be equipped with a plastic sight-barrier panel and hold
1000 paper covers. Unit shall be equipped with four theft-resistant, heavy-duty ABS toilet tissue spindles that hold standardcore rolls up to 5-1/4'' (135mm) diameter (1800 sheets). Spindles shall be removable from cabinet only when door is open.
Manufacturer’s service and parts manual shall be provided to the building owner/manager upon request.
Partition-Mounted Seat-Cover Dispenser, Sanitar y Napkin Disposal, And Toilet Tissue Dispenser Model
B-357 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jack son, Tennessee; Los Angeles,
California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty.
Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-357 Rev. 11/08 R/A, S/F Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.
Loading...