Bobrick B-3474 User Manual

Technical Data

17-3/16''

435mm

30-5/8''

780mm

S

S

15-3/16''

385mm

3-7/8''

100mm

11-5/16''

285mm

1''

25mm

Typ.

S

S

Toilet-Seat-Cover

Dispenser

Toilet Tissue

Dispenser (2)

3-15/16''

100mm

S

Door

28-5/8''

725mm

Recommended Mounting Height Off Floor

For Barrier-Free Design

43-1/2''

1105mm

3''

75mm

Shelf

Grab Bar

(Not Furnished)

33''

840mm

to

Floor

Lock & Key (2)

Finish Face of Wall

Door

3/16''

5mm

Recommended Mounting Height Off Floor

59''

1500mm

Centerline of Toilet Tissue

Dispenser shall be

7'' to 9'' (180 to 230mm)

in Front of Toilet

C

L

ClassicSeries

®

RECESSEd

SEAT-COvER ANd

TOILET TISSuE dISPENSER

B-3474

Rough Wall Opening

16" (405mm) wide
29-1/4" (745mm) high
4" (102mm) minimum

recessed depth

MATERIALS:

Cabinet — 18-8 S, type-304, heavy-gauge stainless steel. All-welded construction. Exposed sur faces have satin finish.

Flange — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn and beveled, one-piece, seamless

construc tion.

Doors — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. One-piece, seamless construction. Secured to
cabinet with a full-length stainless steel piano-hinge. Equipped with a tumbler lock keyed like other Bobrick washroom
accessories.

Toilet Tissue Dispensers (2) — .100" (2.5mm) thick ABS. Equipped with two theft-resistant, heavy-duty, one-piece, molded
ABS spindles.

OPERATION:

Doors unlock with key provided and swing open for filling. Toilet-seat-cover dispenser holds 500 single- or half-fold paper
covers. Spindles may be removed from cabinet when door is open. Unit holds two standard-core toilet tissue rolls up to 5-1/4"
(135mm) diameter (1800 sheets).

Designer's Note: It is recommended that one full toilet tissue roll remain wrapped until the other roll has been depleted to avoid
wasting ends of both rolls.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 7/1/10 R/A, S/D Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2010 by Bobrick Washroom Equipment, Inc.

continued . . .

INSTALLATION:

Provide framed rough wall opening 16" wide x 29-1/4" high (405 x 745mm). Mini mum recessed depth required from finish
face of wall is 4" (102mm). Top of wall opening should be 43-1/2" (1105mm) from finish face of floor to allow placement of
horizontal grab bar at 33" (840mm) height across front of unit. Allow clearance for construction features that may protrude
into rough wall opening from opposite wall. Coordinate with mechani cal engineer to avoid pipes, vents, and conduits in wall. If
unit projects above top of wainscot, provide aluminum channel or other filler to eliminate gap between flange and finish face of
wall. Mount unit in wall opening with shims between framing and cabinet at all points indicated by an S, then secure unit with
#8 x 1-1/4" (4.2 x 32mm) sheet-metal screws (not furnished).

SPECIfICATION:

Recessed toilet-seat-cover and toilet tissue dispenser shall be type-304 stainless steel with all-welded construction; exposed
surfaces shall have satin finish. Toilet tissue dispenser shall be ABS plastic. Flange shall be drawn and beveled, one-piece,
seamless construction. Unit shall mount flush against side wall of barrier-free toilet compartment to allow clearance for grab
bar across front of unit. Doors shall be one-piece, seamless construction; secured to cabinet with a full-length stainless steel
piano-hinge; and equipped with a tumbler lock keyed like other Bobrick washroom accessories. Toilet-seat-cover dispenser
holds 500 paper covers. Unit shall be equipped with two theft-resistant, heavy-duty ABS toilet tissue spindles that hold
standard-core rolls up to 5-1/4" (135mm) diameter (1800 sheets). Spindles shall be removable when door is open.

Recessed Seat-Cover And Toilet Tissue Dispenser shall be Model B-3474 of Bobrick Washroom Equipment, Inc.,
Clifton Park, New York; Jack son, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-3474 Rev. 7/1/10
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2010 by Bobrick Washroom Equipment, Inc.

R/A, S/D

Printed in U.S.A.