MIRROR WITH
S
2-1/16'' to 2-1/2''
50 to 65mm
S
1-7/8''
45mm
2-1/8'' to 3''
55 to 75mm
S
W
H
T
T
Back of Mirror
Locking Screw
(Phillips-Head)
T
Wall Hanger
3/4''
19mm
Outline of Mirror
Frame
Mirror
B-2906
Technical Data
SpEcIAL-ORdER REFLEcTIvE SuRFAcES
Specify Series Required:
STAINLESS STEEL
ANgLE FRAME
B-2908
B-2909
B-2906 Series Polished Stainless Steel Mirror — 72" x 24" (183 x 61cm) or 24" x 48" (61 x 122cm) maximum;
12" x 12" (30 x 30cm) minimum.
B-2908 Series Tempered Glass Mirror — 120" x 48" (305 x 122cm) or 48" x 60" (122 x 152cm) maximum;
16" x 20" (41 x 51cm) minimum.
B-2908 Series Tempered Glass Mirror Standard Sizes — B-2908 1830 18" x 30" (46 x 76cm)
B-2908 1836 18" x 36" (49 x 91cm)
B-2908 2436 24" x 36" (61 x 91cm)
B-2909 Series Laminated Glass Mirror — 96" x 48" (244 x 122cm) maximum; 12" x 12" (30 x 30cm) minimum.
Designer's Notes:
1. Special-order only.
2. All Bobrick framed mirrors are manufactured to overall width and height dimensions. EXAMPLE: A 24" x 36" (61 x 91cm)
mirror will be furnished 24" x 36" (610 x 915mm) outside-of-frame to outside-of-frame.
3. To specify sizes use Series Number followed by width then height in inches. EXAMPLE: B-2906 2024.
4. Bobrick framed mirrors are manufactured to a tolerance ±1/8" (3.2mm).
5. For sufficient space to lift mirror onto wall hanger(s), provide 3-1/4" (85mm) minimum clearance above center line of
mounting screw holes.
6. Provide 1" (25mm) minimum clearance at bottom of mirror for engaging locking screws and 1" (25mm) clearance on each
side.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 9/09 R/B Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
continued . . .
MATERIALS:
Frame — 18-8 S, type-304, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with vertical-grain satin finish. Onepiece, roll-formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame
tightly against mirror. Corners are welded, ground, and polished smooth. Galvanized steel back is fastened to frame with
concealed screws and equipped with integral horizontal hanging brackets. Concealed Phillips-head locking screws securely
fasten mirror to wall hanger(s).
Designer's Note: Type 304 stainless steel provides superior corrosion resistance, compared to 400 Series stainless steel, against
enviromental moisture, hose-down maintenance and strong cleaning solution.
Mirror — (B-2906 Series) Stretcher leveled stainless steel with reflective, highly polished strip finish. Tempered masonite
backing.
(B-2908 Series) No. 1 quality, 1/4" (6mm) tempered select float glass: selected for silvering and electrolytically
copper-plated by the galvanic process.
(B-2909 Series) 1/4" (6mm) thick. Two pieces of 1/8" (3mm) select float glass: selected for silvering,
laminated with 0.003'' (0.08mm) thick clear vinyl in the center, and electrolytically copper-plated by the galvanic
process.
Note: These reflective surfaces resist breakage and provide a measure of safety from broken glass, but differ in
color and reflective quality from standard glass mirrors.
All edges protected by plastic filler strips. Backs of all glass mirrors are protected by full-size, shock-absorbing,
water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding.
Concealed Wall Hanger(s) — 20-gauge (0.9mm) galvanized steel. incorporates lower support member forming rigid
rectangle, which engages lower backplate louvers to keep bottom of mirror against wall.
INSTALLATION:
Mount wall hanger on wall with screws (not furnished) at points indicated by an S. For plaster or dr y wall construction, provide
concealed backing to comply with local building codes, then secure wall hanger with screws (not furnished). For other wall
surfaces, provide fiber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or
expansion bolts. Hang mirror on wall hanger. Lock mirror to wall hanger by tightening Phillips-head locking screws that are
concealed in bottom of frame at points indicated by a T.
SpEcIFIcATION:
Mirror shall have a one-piece type 304 stainless steel angle frame, 3/4" x 3/4" (19 x 19mm) with continuous integral stiffener
on all sides and beveled front to hold frame tightly against mirror; corners shall be welded, ground, and polished smooth; all
exposed surfaces shall have satin finish with ver tical grain. Mirror shall be __________________________ (insert one: polished
stainless steel, tempered glass, or laminated glass). All edges shall be protected by plastic filler strips. Backs of all glass
mirrors shall be protected by full-size, shock-absorbing, water-resis tant, nonabrasive, 3/16" (5mm) thick polyethylene padding.
Galvanized steel back shall have integral horizontal hanging brackets located at top for mounting on concealed rectangular wall
hanger. Mirror shall be secured to wall hanger with concealed Phillips-head locking screws located in bottom of frame.
Framed Mirror shall be Model _______________ (inser t model number) of Bobrick Washroom Equipment, Inc.,
Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-2906 Revised 9/09 R/B Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
Loading...