Finish Face of Wall
5-5/16''
135mm
Lock & Key
12-1/4''
310mm
Door
S
S
7-9/16''
190mm
Recommended Mounting Height Off Floor
for Universal/Barrier-Free Design
30''
760mm
Cabinet
1-1/8''
30mm
20-13/16''
525mm
5-5/8''
145mm
9-9/16''
245mm
5/32''
4mm
Typ.
S
S
S
S
C
L
Mount within 12''
(305mm)
of Front of Toilet Seat
Viewing Slot
Lever & Sliding Access Panel
11-3/8''
290mm
Surface-Mounted
Technical Data
tWIn JuMBo-roLL
toILet tISSue dISPenSer
Patented
B-2892
MaterIaL:
Cabinet — 18-8 S, type-304, 20-gauge (1.0mm) stainless steel with satin-finish. Equipped with a tumbler lock keyed like other
Bobrick washroom accessories.
Door — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin-finish. Drawn, one-piece, seamless construction. Wide
viewing slot reveals toilet tissue supply inside cabinet.
Dispensing Mechanism — High-impact ABS.
oPeratIon:
Door unlocks with key provided and swings down for loading dispenser. Spindles accommodate two toilet tissue rolls up to 10"
(255mm) diameter with 3" (75mm) diameter core, or remove outer spindle (which is held in place with 3 snaps) from the inner
spindles to accommodate 2-1/4" (55mm) diameter core rolls. Unique sliding access panel exposes one roll at a time for patron
use, assuring uninterrupted, complete no-waste use of first roll before starting the reserve roll; allows easy roll change-over.
When first roll is depleted, move the lever at the bottom of dispenser to the left until sliding access panel locks in position and
exposes roll on right. When door is opened for reloading, the sliding access panel automatically releases and returns to the
original position on the right. Move the remaining roll to the first position on left and install a new roll on the right spindle.
Wide viewing slot in door reveals the amount of toilet tissue on both rolls. Unit is designed for quick reloading.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 7/08 S/B, R/A Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.
continued . . .
InStaLLatIon:
Mount unit on wall or toilet partition with four sheet-metal screws, furnished by manufacturer, at points indicated by an S. Rear
edge of unit should be 20" (510mm) from back wall. This locates toilet tissue within 12" (305mm) of front of standard toilet that
projects 30" (760mm) from back wall.
For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with
sheet-metal screws furnished. For other wall sur faces, provide fiber plugs or expansion shields for use with sheet-metal screws
furnished, or provide 1/4" (6mm) toggle bolts or expansion bolts.
For partitions with par ticle-board or other solid core, secure with sheet-metal screws or provide through-bolts, nuts, and
washers. For hollow-core metal partitions, provide solid backing into which sheet-metal screws can be secured. If two units are
installed back-to-back, then provide threaded sleeves and machine screws for the full thickness of partition.
SPecIfIcatIon:
Jumbo-roll toilet tissue dispenser door and cabinet shall be type-304 stainless steel with satin-finish: door shall be 18 gauge
(1.2mm); cabinet shall be 20 gauge (1.0mm). Cabinet shall be equipped with a tumbler lock keyed like other Bobrick washroom
accessories. Door shall have a wide viewing slot to reveal toilet tissue supply inside cabinet. Dispensing mechanism shall be
constructed of high-impact ABS shall accommodate two toilet tissue rolls up to 10" (255mm) diameter with 3" (75mm) diameter
core; and be equipped with a sliding access panel that exposes one roll at a time. Spindles shall be convertible in the field to
dispense 2-1/4" (55mm) diameter core rolls by removing outer spindles furnished in-place. Manufacturer’s service and par ts
manual shall be provided to the building owner/manager upon request.
Surface-Mounted Twin Jumbo-Roll Toilet Tissue Dispenser shall be Model B-2892 of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-2892 S/B, R/A Rev. 7/08 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.
Loading...