Bobrick B-26607 User Manual

SURFACE-MOUNTED

Technical Data

96mm

Measurments (ca.) are in mm

286mm

SOAP CARTRIDGE

DISPENSER 500ML

Drilling Specifications

Lock

& Key

S

65mm

S

203mm

S

32mm

Finish Face of Wall

Plastic

Container

B-26607

116mm

153mm

301mm

105mm

310mm

100-110cm

MATERIAL:

Welded, 0.8mm (22 gauge) 1.4301, Typ CrNi 18/10, AISI 304 stainless steel housing with satin finish; stainless
steel operating lever; metal lock and key; soap level indicator; interchangeable plastic containers with plastic
pumps; variety of plastic containers available including containers with pumps for soap or foam.

OPERATION:

The cover is lockable with a Bobrick System lock. To refill the dispenser, open the cover by lifting and pulling for ward. The soap level
indicator shows how much product is remaining in the dispenser. The plastic container can be removed and re-installed for quick and
easy refilling. The plastic container can be used for soap cartridges (up to 500 ml), as well as bulk refilling of up to 500 ml of soap. To
install a soap cartridge in the dispenser, open the cartridge and place it upside down inside the plastic container. Alternatively, soap
can be poured directly into the plastic container. The dispenser has been designed for quick and easy refilling process.

INSTALLATION:

After opening the dispenser cover, remove the plastic container, gently lifting it upwards while pressing the locking latch. Mount the
dispenser to the wall by using the enclosed screws and wall plugs. Make sure the wall surface is in good condition to ensure proper
mating of the dispenser to the wall. Use silicone or glue pads if necessary.

Note:

1. The dispenser should be installed near or directly above the sink to allow wet hands to drip into the sink.

2. Be sure to leave enough space above the dispenser to open the cover, remembering to leave sufficient room to exchange containers.

3. Recommended installation height: 100 – 110 cm (measured from floor to the bottom of the dispenser).

TECHNICAL SPECIFICATIONS:

Model B-26607 from Bobrick Washroom Equipment, Dispenser made of 0.8 mm thick, (22 gauge) 1.4301, Type CrNi 18/10, AISI 304
stainless steel with a brushed, satin finish; plastic container for soap car tridges (up to 500 ml), as well as for bulk refill of soap (up to
500 ml); lockable with a Bobrick System lock; soap level indicator.

CARE INSTRUCTIONS:

Clean regularly with warm water and/or stainless steel cleaner.
Do not use acid (chloride) cleaners or scouring agents.
The suction valve can be cleansed by pumping hot water through it.
Do not dismantle the dispenser.
Use only original spare parts.

Soap Cartridge Dispenser shall be Model B-26607 of Bobrick Washroom Equipment, Inc., Clifton Park, New York;
Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick
Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

Recommended Mounting Height Off Floor

continued . . .

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 1/08 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.

INSTALLATION INSTRUCTIONS

BOBRICK SURFACE-MOUNTED SOAP CARTRIDGE DISPENSER

1. Install dispenser near or directly above sink to allow wet hands to drip into sink.

2. Allow sufficient space above dispenser to exchange cartridges easily.

3. Recommended installation height: 100 – 110 cm (39"-43") (measured from floor to bottom of dispenser).

4. For installation please follow instructions down below:

1. Mount dispenser to wall
using enclosed screws and
wall plugs.

5. Press lever several times
to prime pump.

2. Insert plastic container
into dispenser.

A. To change cartridge: open dispenser.

4. Replace dispenser cover.3. Ensure both top and
bottom of container are
correctly seated in dispenser.

B. Press locking latch and lift cartridge
up and out.

© 2008 by Bobrick Washroom Equipment, Inc.

B-26607 Revised 1/08 Printed in U.S.A.

In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.

200 Commerce Drive, Clifton Park, New York 12065-1350 • Tel: [phone] • FAX: [phone]
11611 Hart Street, North Hollywood, California 91605-5882 • Tel: [phone] • FAX: [phone]
100 Bobrick Drive, Jackson, Tennessee 38301-5625 • Tel: [phone] • FAX: [phone]

In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY

45 Rolark Drive, Scarborough, Ontario M1R 3B1 • Tel: [phone] • FAX: [phone]