Bobrick B-2300 Installation Manual

18

23

25

12

23

24

17

8

20

19

19

20

15

16

14

13

8

12

11

2

5

6

7

4

10

3

1

9

2

21

Limited One Year Warranty

T&S warrants to the original purchaser (other than for purposes
of resale) that such product is free from defects in material and
workmanship for a period of one (1) year from the date of purchase.
During this one-year warranty period, if the product is found to be
defective, T&S shall, at its option, repair and/or replace it. To obtain

warranty service, products must be returned to.....

T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department
2 Saddleback Cove
Travelers Rest, SC 29690

Shipping, freight, insurance, and other transportation charges of
the product to T&S and the return of repaired or replaced product to
the purchaser are the responsibility of the purchaser. Repair and/or
replacement shall be made within a reasonable time after receipt by
T&S of the returned product. This warranty does not cover items which
have received secondary finishing or have been altered or modified
after purchase, or for defects caused by physical abuse to or misuse of
the product, or shipment of the products.
Any express warranty not provided herein, and any remedy for Breach
of Contract which might arise, is hereby excluded and disclaimed.
Any implied warranties of merchantability or fitness for a particular
purpose are limited to one year in duration. Under no circumstance
shall T&S be liable for loss of use or any special consequential cost,
expenses or damages.
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
Specific rights under this warranty and other rights vary from state to
state.

P/N:

DATE:

DRAWN:

CHECKED:

APPROVED:

098-016898-45 Rev. 1
11-08-10
TEH
JRM 11-12-10
JHB 11-12-10

8” FIXED CENTER

CONCEALED

WIDESPREAD

B-2300, B-2800,

B-2900 SERIES

Installation and

Maintenance

Instructions

1
2
3
4
5
6
7
8

9

12

22
19
20

21

Base Faucet Assembly
Side Flange Nut
C-Washer
Center Flange Nut
Compression & Nut Fitting

Compression Nut

Compression Fitting
Center Shank:
Center Shank, Swivel
Center Shank, Rigid
Coupling Nut
Escutcheons:

Escutcheon, Bell

Escutcheon, Metering
Hanger
Rigid & Swivel Goosenecks
Aerators:

55/64”-27 Female Threads

3/8” NPSM Male Threads

13/16”-27 Male Threads

Stream Regulator, Plain

Stream Regulator w/ Screen
Sidespray & Hose Assembly
Star Washer, Anti-Rotation

N/A
N/A
016749-45
016742-45
016745-45
N/A
N/A

016754-40
016847-40
000958-20

001257-40
017292-45
016777-45
Inquire w/ T&S

B-0199-01
B-0199-02
B-0199-03
B-LT
B-PT
001495-45
014200-45

Patent # 7,472,434

Parts List

10

11

23
24
25

Cartridge, Hot Eterna Teflon

Cartridge, Hot Cerama
Cartridge, Cold Eterna Teflon

Cartridge, Cold Cerama
Wrist Action Metering
Hot Eterna Teflon - Short
Push Button Metering
Pivot Action Metering - Hot (shown)
Pivot Action Metering - Cold (shown)

016753-40
016767-25
016752-40
016768-25
012449-40
017327-40
238A
238AH-PA
238AC-PA

13

14

15

16

17
18

Handle, 4” Wrist Action (shown)

Handle, Lever

Handle, 4-Arm
Screw, 4” Wrist Action (shown)

Screw, Lever Handle
Index, Snap-In Red (Hot) (shown)

Index, Lever Handle (Hot)
Index, Snap-In Blue (Cold) (shown)

Index, Lever Handle (Cold)
Pivot Action Handle - Hot
Pivot Action Handle - Cold
Cold Cap Assembly
Hot Cap Assembly
Lavatory Handle, 3-Wing - Cold
Lavatory Handle, 3-Wing - Hot
Fast Self-Closing Asm - Cold
Fast Self-Closing Asm - Hot
Cold Alpine Handle Assembly
Hot Alpine Handle Assembly

B-WH4
001638-45
002521-45
000925-45
000922-45
001194-45
001661-45
001686-45
001660-45
PA-H
PA-C
014195-40
014194-40
001784-40
001783-40
002875-40
002876-40
076F-C
076F-H

Handle Assemblies

Cartridge Assemblies

Opt.B

Opt.B
Opt.B
Opt.B
Opt.B
Opt.B

Opt.B
Opt.B
Opt.B
Opt.B
Opt.B
Opt.B
Opt.B
Opt.B
Opt.B
Opt.B

Option B

Option B: Contains low-profile escutcheon to accommodate
push button metering, pivot action metering, alpine, dome,
3-wing, fast self-close and wrist action metering.

22

Before starting the installation, be sure to flush supply lines and shut off water supply.

Step 1:

Take center shank out of body.

Step 3:

Insert body into deck holes until hanger snaps to top of deck.
Place c-washers under bonnet nuts on side bodies.

Step 5:

Squeeze hanger loops and allow hanger to drop through center
hole.

Step 4:

Option B: Screw metering escutcheons over c-washers. Tighten
cartridges.

Step 6:

Remove nuts as shown. Option B: Remove retaining rings from cartridges.
Place center body through center hole into main body. Tighten 3 flange
nuts. Tighten compression nut to seal center body.

1. Tighten diverter to center body using
flat head screwdriver.

2. Remove locknuts from hose guide,
place it through existing hole in sink.
Reinstall locknut on the hose guide.
Tighten by hand.

3. Apply Teflon tape to threaded end of
sidespray, insert through hose guide and
attach threaded end of side spray to base
of center body. Tighten with wrench.

4. Turn on water and check for leaks.

Step 2:

Place hanger on body. Add center flange nut to top of
compression nut. Option B: Remove cartridges.

Step 7:

Add escutcheons, packing nuts, handles, spout and tighten. Option B: Add
handles, retaining rings, spout and tighten. Turn on water supply and check for

leaks.

For models with sidespray:

Option B

Option B

Option B

Option B

Option B

Option B

Swivel to Rigid Gooseneck Swivel to Rigid Gooseneck
OptionOption: Uninstall and lift

out gooseneck. Place star
washer into swivel body.
Reinstall gooseneck.