Technical Data
MirrOr WitH
staiNless steel
CHaNNel FraMe
aNd sHelF
B-166
series
SNAP LOCKING DESIGN
(Rear View)
1/2''
Mirror
13mm
5''
125mm
Frame
3/8''
10mm
4'' or 5" Typ.
100 or 125mm
Back Plate/Wall Hanger
S
Side View
2-1/2''
65mm
2-9/16''
65mm
S
S
Mirror
Figure: 1 Figure: 2
staNdard B-166 series MirrOrs
MOdel
NO.
B-166 1824 18'' (46cm) 24'' (61cm)
B-166 1830 18'' (46cm) 30'' (76cm)
B-166 1836 18'' (46cm) 36'' (91cm)
B-166 2436 24'' (61cm) 36'' (91cm)
OVerall siZe
W H
SCREW LOCKING DESIGN
(Rear View)
1/2''
13mm
5''
125mm
3/8''
10mm
Frame
all OtHer siZe MirrOrs
T
3"
75mm
Locking Screw
(Phillips-Head)
2-1/16''
50mm
S
1-13/16''
45mm
S
S
Designer’s Notes:
1. Special-order sizes available on request.
2. Maximum size mirror available, 24'' x 60'' (61 x 152cm); minimum size, 12" x 12" (30 x 30cm). Maximum shelf length is 24" (61cm).
3. All Bobrick framed mirror/shelf models are manufactured to overall width and height dimensions including shelf. EXAMPLE: A 24'' x 36'' (61 x 91cm) mirror
will be furnished 24'' x 36'' (61 x 91cm) outside-of-frame to outside-of-frame including shelf.
4. To specify special sizes use Series Number followed by width then height in inches. EXAMPLE: B-166 2024.
5. Bobrick framed mirror/shelf models are manufactured to a tolerance
6. For sufficient space to lift mirror onto wall hanger(s), provide 3-1/4'' (85mm) minimum clearance above center line of mounting screw holes.
7. Provide 1'' (25mm) minimum clearance at bottom of mirror for engaging locking screws and 1'' (25mm) clearance on each side.
± 1/8'' (3.2mm).
Materials:
Frame — Type 430 stainless steel, 1/2" x 1/2" x 3/8" (13 x 13 x 9.5mm) channel 1/4" (6mm) return at rear with bright polished finish. One-piece frame with 90 degree mitered corners. Galvanized steel back has integral horizontal hanging brackets
near the top for hanging the mirror and near the bottom to prevent the bottom of the mirror from pulling away from the wall.
Locking devices secure mirror to concealed wall hanger. In Screw Locking Design(see figure 2), concealed Phillips-head locking screws securely fasten mirror to wall hanger.
Shelf — 18-8 S, type 304, 22-gauge (0.8mm) stainless steel with satin finish. 3/8" (10mm) return edges on front and sides with
front edge hemmed for additional safety. Shelf is welded to mirror frame and reinforced by concealed 16-gauge (1.6mm) stainless steel brackets. No exposed rivet-heads, screws, or fasteners of any type appear on frame or shelf.
Mirror — No. 1 quality, 1/4" (6mm) select float glass: selected for silvering, electrolytically copper-plated by the galvanic
process, and guaranteed for 10 years against silver spoilage. Corners are protected by friction-absorbing filler strips; back is
protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding.
Concealed Wall Hanger — 20-gauge (9.0mm) galvanized steel. Incorporates lower support member, forming rigid rectangle,
which engages lower backplate louvers to keep bottom of mirror against wall.
continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 9/09 R/B Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
Approx. 1"
(25mm)
S
S
C
L
T
T
Initial
Position
Final
Position
iNstallatiON:
Mount wall hanger on wall with screws (not furnished) at points indicated by an S. For plaster or dr y wall construction, provide
backing to comply with local building codes, then secure wall hanger with screws (not furnished). When providing a concealed
backing, allow backing to cover minimum range of mounting hole locations shown on drawing. For other wall surfaces, provide
fiber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or expansion bolts.
Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members. To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1" (25mm) above final
position and then lowered into final position.
Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final
position. Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror near the bottom
or under the bottom of the mirror and pulling mirror bottom forward and then up (see figure 3).
Screw locking Design — Lock mirror to wall hanger by tightening Phillips-head locking screws that are concealed in the
bottom of frame by points indicated by a T. Mirror may be unlocked from wall hanger by loosening locking screws and lifting
mirror of f of concealed wall hanger (see figure 4).
S
S
SNAP LOCKING DESIGN
(Front View)
Approx. 1"
(25mm)
C
L
Initial
Position
Final
Position
SCREW LOCKING DESIGN
(Front View)
Figure: 3 Figure: 4
speCiFiCatiON:
Mirror shall have a one-piece type 430 stainless steel channel frame, 1/2" x 1/2" x 3/8" (13 x 13 x 9.5mm), with 90° mitered
corners; all exposed surfaces shall have bright polished finish. Shelf shall be type 304, 22-gauge (0.8mm) stainless steel with
satin finish and shall have 3/8" (10mm) return edges on front and sides with front return edge hemmed. Shelf shall be welded
to mirror frame and reinforced by concealed stainless steel brackets. No rivet-heads, screws, or fasteners of any kind shall
be exposed on frame or shelf. Select float glass mirror shall be guaranteed for 10 years against silver spoilage. Corners shall
be protected by friction-absorbing filler strips and the back shall be protected by full-size, shock-absorbing, water-resis tant,
nonabrasive, 3/16" (5mm) thick polyethylene padding. Galvanized steel back shall have integral horizontal hanging brackets
located at top and bottom for mounting on concealed rectangular wall hanger and to prevent the mirror from pulling away from
the wall. Locking devices secure mirror to concealed wall hanger. Mirror shall be removable from wall.
Framed Mirror With Shelf shall be Model B-166 _______________ (insert width and height) of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-166 Rev. 9/09 R/B Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.
Loading...