Bobrick 2180 User Manual
Technical Data
29''
74cm
33''
84cm
8''
20cm
Finish Face of Wall
Stile Door or Panel
76-5/16''
196cm
Headrail
72''
183cm
85''
216cm
4-5/16''
11cm Min.
4-5/16''
11cm Min.
X''
32''
81cm
8''
20cm
72''
183cm
Post
10'0''
305cm
Max.
As
Required
10'0''
305cm
Max.
72''
183cm
.
72''
183cm
29''
74cm
33''
84cm
8''
20cm
72''
183cm
4-5/16''
11cm Min.
8'0''/244cm
or as required
up to 10'0
''
/305cm
4-5/16''
11cm Min.
4-5/16''
11cm Min.
29''
74cm
33''
84cm
8''
20cm
29''
74cm
33''
84cm
8''
20cm
4''
10cm
Typ.
32''
81cm
Slide
Latch
Keeper
Bracket
Panel
Screw
Bracket
Coat
Hook
Hinge
Hinge
Bracket
Threaded
Inserts
Stile
Door
Threaded
Inserts
Stile
Threaded
Inserts
Door
Screw
Screw
Angle
Bracket
Continuous
Hinge
Slide
Latch
Keeper
Door
Stop
Angle
Bracket
Threaded
Inserts
Stile
Door
Threaded
Inserts
Stile
Threaded
Inserts
Door
U-channel
Continuous Hinge
Panel
Screw
Coat
Hook
Threaded
Rod
Lock Washer
Flat Washer
Hex Nut
Stile
Leveling Bar
Shoe Retainer
I-Beam
(not furnished)
Finished
Ceiling
Bevel Washer
Spacer
Hex Nut
Flat Washer
Lock Washer
Hex Nuts
Threaded Rod
Flat Shoe Retainer
Wedge Anchor
Flat Washer
Leveling Bar
Wall Bracket
Stile
Headrail
(cross section)
DuraLineSeries
®
MAXIMUM-PRIVACY
CLASS A FIRE-RESISTANT
PARTITIONS AND SCREENS
2180
SERIES
Specify Product Application:
Toilet Partitions
Dressing Compartments
Urinal Screens
Entrance Screens
With Outswing Door
With Institutional Hardware (.67)
STANDARD-SIZE COMPONENTS:
Stiles: For compartments — 8''
a
, 10'', 12'', 16'', 20'', or 24'' (20, 25, 30, 41, 51, or
Specify Series Required:
2181 Series Floor-Anchored
2182 Series Overhead-Braced
2183 Series Post-to-Ceiling (Screens only)
2186 Series Floor-to-Ceiling Anchored
2188 Series Ceiling-Hung for 8' 0'' (244cm) Ceilings or
as required up to 10' 0'' (305cm) Ceilings
61cm) wide; for screens — 6'' (15cm) wide. Floor-anchored — 75-5/16'' (194cm)
high; overhead-braced — 83'' (211cm) high; floor-to-ceiling anchored — height
as required; ceiling-hung — 83'' (211cm) high for 8' 0'' (244cm) ceilings or as
required up to 10' 0'' (305cm) ceilings.
Doors: 72'' (183cm) high. Inswing doors are standard for 22'' to 37'' (56–94cm)
widths in whole-inch increments. Outswing
b
doors are standard for 25'' to 37''
(64–94cm) widths in whole-inch increments.
COMPARTMENT AND SCREEN ELEVATIONS TYPICAL HARDWARE DETAILS
Melamine
Surfaces
Solid Phenolic
Core Edges
are Black
Panels: For compartments — Up to 84'' (213cm) wide, 72'' (183cm) high. For
ceiling-hung and post-to-ceiling screens — 24'', 36'', 48'', or 60'' (61, 91, 122, or
152cm) wide; 58'' (147cm) high.
Note: If the width of the panel exceeds 60'' (152cm) the panel will be two pieces and
require an H Channel to obtain 72'' (183cm) height requirement.
Posts: For 2183 Series post-to-ceiling screens only. 1-1/4'' (3cm) square. 10 ft
(305cm); cut to required height in field.
a
Minimum 8'' (20cm) wide stile is required for all maximum-privacy
compartments.
b
Use outswing doors to comply with local codes requiring access for physically
disabled persons.
Commercial Hardware
(standard on all compartments)
2186 Series
2181 Series Floor-Anchored
2182 Series Overhead-Braced
Floor-to-Ceiling Anchored
Institutional Hardware
(.67 option)
These mounting points require backing. For suggested backing methods, Bobrick Advisory Bulletins TB-32 for ceiling-hung installations and TB-46
for floor-anchored are available upon request.
2188 Series Ceiling-Hung
2183 Series Post-to-Ceiling Screen
Standard gaps are provided at all walls and
between components to allow for hardware
attachment.
Wall gaps are standard 1/2" to 1"
TYPICAL INSTALLATION DETAILS
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2007 by Bobrick Washroom Equipment, Inc.
Front Side Front
Overhead-BracingFloor Leveling DeviceCeiling Leveling Device
Side
MATERIALS:
Stiles* — 3/4'' (19mm) thick, solidly fused plastic laminate with matte-finish melamine surfaces, colored face sheets, and black phenolic-resin core that are integrally
bonded. Edges are black. Leveling Device: 3/16" (5mm) thick, corrosion-resistant, chromate-treated, double zinc-plated steel angle leveling bar bolted to stile; fur nished
with 3/8'' (10mm) diameter threaded rods, hex nuts, lock washers, flat washers, spacer sleeves, expansion anchors, and shoe retainers. Shoe: 18-8 S, type-304, 22-gauge
(0.8mm) stainless steel with satin finish; 4'' (102mm) high.
*
Stiles for 2186 Series floor-to-ceiling anchored units have a leveling device at each end.
Panels — 1/2'' (13mm) thick, solidly fused plastic laminate with matte-finish melamine surfaces, colored face sheets, and black phenolic-resin core that are integrally
bonded. Edges are black.
Doors — 3/4'' (19mm) thick, solidly fused plastic laminate with matte-finish melamine sur faces, colored face sheets, and black phenolic-resin core that are integrally
bonded. Edges are black.
Posts (for 2183 Series screens only) — 1-1/4'' (32mm) square tubing; 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. Floor and ceiling connections
are constructed of 18-8 S, type-304, heavy-gauge stainless steel. Furnished in 10-ft (305-cm) lengths; to be cut in field to job specifications.
Headrail (for 2182 Series compartments only) — Extruded anodized aluminum with satin finish. Enclosed construction with sloping top. Face has raised grip-resistant
edge.
Designer's Notes: Headrails with integral curtain tracks and hooks are available for compartments without doors. Optional vinyl curtains are available. Benches are available
as an optional accessory for dressing compartments and shower dividers: 1/2'' (13mm) thick, solidly fused plastic laminate with matte-finish melamine surfaces, colored
face sheets, and black phenolic-resin core that are integrally bonded, 10'' (25cm) deep, 18'' or 24'' (46 or 61cm) wide; furnished with two stainless steel support brackets for
mounting to wall or divider panel.
Commercial Hardware (standard) — Hinges, door latches, door keepers, coat hooks, and mounting brackets are constructed of 18-8 S, type-304, heavy-gauge stainless
steel with satin finish. Threaded inserts are factory installed for securing hinges and door latch. Theft-resistant, stainless steel pin-head, torx screws are furnished for door
hardware and all mounting brackets. Black rubber bumper on the latch serves as door bumper for inswing door. Balanced hinge is adjustable to hold door of unoccupied
toilet compartment partially open or fully closed. Toilet compartment door is locked from inside by sliding door latch into keeper. A locked compartment may be opened
from outside by lifting door to disengage latch from keeper. Track of door latch prevents inswing door from swinging out beyond stile; on outswing door, the door keeper
prevents it from swinging in beyond stile.
Institutional Hardware (.67 option) — Hinges, door latches, door keepers, door stop plates, U-channels, and angle brackets are constructed of 18-8 S, type-304, heavygauge stainless steel with satin finish: one-piece, full-height hinge is 16 gauge (1.6mm); one-piece door keeper is 11 gauge (3.2mm); one-piece, full-height U-channels and
angle brackets are 18 gauge (1.2mm). U-channels secure panels to stiles, and angle brackets secure panels and stiles to walls. Door latch slides on a shock-resistant nylon
track. A locked compartment may be opened from outside by lifting door to disengage latch from keeper. Two doorstops prevent door from being kicked out by vandals.
Theft-resistant, stainless steel pin-head, tor x screws are furnished for door hardware, U-channels, and angle brackets. Doors are equipped with a self-closing hinge. Threaded
inserts are factory installed to secure door hinge, latch, and doorstops. To specify Institutional hardware, add suffix .67 to series number. Example: specify 2182.67 for overhead-
braced, maximum- privacy partitions furnished with Institutional hardware, including factory-installed threaded inserts for door hardware attachment.
INSTALLATION:
Bobrick installation instructions are packed with each shipment and are available also in advance on request.
Notes:
1. Ceiling-hung and floor-to-ceiling toilet compartments require structural members (not furnished by Bobrick) in ceiling. For suggested types of ceiling support systems,
see Bobrick Advisory Bulletin TB-32.
2. Wall backing is required to secure the mounting brackets of panels, stiles, and wall posts. For suggested wall backing, see Bobrick Advisory Bulletin TB-46.
3. Floor-anchored stiles are furnished with expansion shields and threaded rods. The expansion shields require minimum 2'' (50mm) penetration into minimum 3'' (75mm)
thick structural concrete.
4. Bobrick stainless steel partition-mounted washroom accessories are available for mounting in panels between two compar tments. See current Bobrick Catalog for description of accessories. Cutouts in panels can be pre-cut for Bobrick models at factory if location and size of all cutouts and Bobrick model numbers are fur nished at time of
order.
5. Where water from showers come into contact with par titions, Bobrick 1080 water-resistant, solid phenolic partitions are recommended.
6. If the width of the panel exceeds 60'' (152cm) the panel will be two pieces and require an H Channel to obtain 72'' (183cm) height requirement.
GUARANTEE:
Bobrick toilet par titions including all hardware and mounting brackets are guaranteed to be free from defects in material and workmanship for a period of one year from
date of purchase. Any products returned to Bobrick under this guarantee will be repaired or replaced at no charge. 10-Year Warranty: Bobrick extends a ten-year limited
warranty from date of purchase for DuraLineSeries™ solid phenolic par tition panels, doors, and stiles against breakage, corrosion, delamination, and defects in factory
workmanship when materials are properly installed, then used and serviced normally.
SPECIFICATION:
Class A fire-resistant, solid phenolic ____________________ (insert one: toilet partitions, dressing compar tments, urinal screens, entrance screens) shall be _______________
(insert one: floor-anchored, overhead-braced, floor-to-ceiling anchored, ceiling-hung, post-to-ceiling). Stiles, panels and doors shall be constructed of solidly fused plastic
laminate with matte-finish melamine surfaces, colored face sheets, and black phenolic-resin core that are integrally bonded; and covered by a 10-year limited warranty
against breakage, cor rosion, and delamination. Stiles and doors shall be 3/4'' (19mm) thick; panels shall be 1/2'' (13mm) thick. All units shall meet NFPA Class A, UBC
Class I, ASTM E-84 Fire-Resistance Standards: flame spread 20, smoke development 95. Stiles shall have leveling device that is concealed by a one-piece, type-304, satin-finish stainless steel shoe that is 4'' (102mm) high. Stiles, panels and doors shall be __________ (inser t color name and number from current Bobrick Catalog). Headrails for
overhead-braced compartments shall be anodized aluminum with satin finish.
**
All door hardware and mounting brackets shall be type-304 stainless steel with satin finish.
No door hardware or mounting brackets shall be exposed on exterior of compartments, except on outswing doors. All doors shall be supplied with three hinges. Threaded
inserts shall be factory installed for securing hinges and door latches. Theft-resistant, stainless steel pin-head, torx screws shall be furnished for door hardware and all
mounting brackets. A coat hook shall be furnished for each door. Hinges shall be adjustable to hold doors of unoccupied compartments par tially open or fully closed, and
shall allow a locked compartment to be opened from outside by lifting door to disengage latch from keeper.
**
To specify Institutional hardware, replace end of specification paragraph with: .67 option All door hardware, U-channels, and angle brackets shall be type-304 stainless steel
with satin finish: one-piece, full-height hinges shall be 16 gauge (1.6mm); one-piece door keepers shall be 11 gauge (3.2mm); one-piece, full-height U-channels and angle
brackets shall be 18 gauge (1.2mm). U-channels shall be furnished to secure panels to stiles, and angle brackets furnished to secure panels and stiles to walls. Two doorstops
shall be furnished for each door to prevent it from being kicked out by vandals. Theft-resistant, stainless steel pin-head, torx screws shall be furnished for door hardware,
U-channels, and angle brackets. Hinges shall allow locked compar tment to be opened in emergency from outside by lifting door to disengage latch from keeper. Doors shall
be equipped with a self-closing hinge. Threaded inserts shall be factory installed to secure all door hinges, latches, and doorstops. Manufacturer's service and parts manual
shall be provided to the building owner/manager upon request.
_________________ (insert one: Toilet Partitions, Dressing Compartments, Shower Dividers, Urinal Screens, Entrance Screens) shall be ____________________
Series (insert series number) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick
Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited,
United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. 2180 Revised 4/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2007 by Bobrick Washroom Equipment, Inc.
Loading...