Technical Data
Laminated
Plastic Surfaces
and Edges
3-ply,
45-lb Density
Particle Board
64''
163cm
72''
183cm
10'0''
305cm
Post
Headrail
72''
183cm
85''
216cm
8''
20cm
33''
84cm
29''
74cm
X''
8' 0''/244cm
or as required
up to 10' 0''/305cm
8''
20cm
33''
84cm
29''
74cm
Finish Face of Wall
Stile
Door or Panel
72''
183cm
4-5/16''
11cm Min.
76-5/16''
196cm
72''
183cm
8''
20cm
4-5/16''
11cm Min.
4-5/16''
11cm Min.
4-5/16''
11cm Min.
8''
20cm
33''
84cm
29''
74cm
4''
10cm
Typ.
Screw
Bracket
Coat
Hook
Slide
Latch
Hinge
Keeper
Bracket
Screw
Panel
Bracket
Hinge
Stile
Door
Steel
Core
Threaded
Inserts
T-Nuts
Door
Threaded
Inserts
Stile
Stile
Shoe
Hex Nut
Flat Washer
Leveling Bar
Threaded Rod
Shoe Retainer
Wedge Anchor
Lock Washer
Wall Bracket
Stile
Headrail
(cross section)
Finished
Ceiling
Shoe Retainer
Shoe
Flat Washer
Threaded
Rod
Stile
Hex Nut
Lock Washer
Spacer
Bevel
Washer
I-Beam
(not furnished)
Leveling Bar
DesignerSeries™
MAXIMUM-PRIVACY PARTITIONS
AND SCREENS WITH LAMINATED
PLASTIC SURFACES AND EDGES
2040
SERIES
Specify Product Application:
Toilet Partitions
Dressing Compartments
Urinal Screens
Entrance Screens
With Outswing Door
Specify Series Required:
2041 Series Floor-Anchored
2042 Series Overhead-Braced
2043 Series Post-to-Ceiling (Screens only)
2048 Series Ceiling-Hung for 8' 0'' (244cm) Ceilings or
as required up to 10' 0'' (305cm) Ceilings
STANDARD-SIZE COMPONENTS:
Stiles: For compartments — 8''
a
, 10'', 12'', 16'', 20'', or 24'' (20, 25, 30, 41, 51, or
61cm) wide; for screens — 6'' (15cm) wide. Floor-anchored — 75-5/16'' (194cm)
high; overhead-braced — 83'' (211cm) high; ceiling-hung — 83'' (211cm) high
for 8' 0'' (244cm) ceilings or as required up to 10' 0'' (305cm) ceilings.
Doors: 72'' (183cm) high. Inswing doors are standard for 22'' to 37'' (56–94cm)
widths in whole-inch increments. Outswing
b
doors are standard for 25'' to 37''
(64–94cm) widths in whole-inch increments.
COMPARTMENT AND SCREEN ELEVATIONS
Panels: For compartments — Up to 60'' (152cm) wide; 72'' (183cm) high. For
ceiling-hung and post-to-ceiling screens — 24'', 36'', 48'', or 60'' (61, 91, 122, or
152cm) wide; 72'' (183cm) high.
Posts: For 2043 Series post-to-ceiling screens only. 1-1/4'' (3cm) square. 10 ft
(305cm); cut to required height in field.
a
Minimum 8'' (20cm) wide stile is required for all maximum-privacy
compartments.
b
Use outswing doors to comply with local codes requiring access for physically
disabled persons.
TYPICAL HARDWARE DETAILS
Commercial Hardware
(standard on all compartments)
2041 Series Floor-Anchored
2048 Series Ceiling-hung
These mounting points require backing. For suggested backing methods, Bobrick Advisory Bulletins TB-32 for ceiling-hung installations and TB46 for floor-anchored are available upon request.
Ceiling Leveling Device Floor Leveling Device
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2007 by Bobrick Washroom Equipment, Inc.
Front Side Front Side
2042 Series Overhead-Braced
2043 Series Post-to-Ceiling Screen
TYPICAL INSTALLATION DETAILS
Standard gaps are provided at all walls and
between components to allow for hardware
attachment.
Wall gaps are standard 1/2" to 1"
Overhead-Bracing
MATERIALS:
Stiles — 1'' (25mm) finished thickness: 3-ply, 45-lb (20.4-kg) density, resin-impregnated particle board is bonded to each side of 11-gauge
(3.2mm) sheet steel that serves as reinforcing core; surfaces and edges are .050'' (1.3mm) thick, high-pressure plastic laminate with colored
face sheets and matte finish. Leveling Device: 3/8'' x 1'' (10 x 25mm) steel bar is welded to sheet-steel core of stile, forming a single structural unit; furnished with 3/8'' (10mm) diameter threaded rods, hex nuts, lock, flat washers, expansion shields, and shoe retainers. Shoe:
18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish; 4'' (102mm) high.
Panels and Doors — 1'' (25mm) finished thickness: 3-ply, 45-lb (20.4-kg) density, resin-impregnated particle board; surfaces and edges
are .050'' (1.3mm) thick, high-pressure plastic laminate with colored face sheets and matte finish.
Posts (for 2043 Series screens only) — 1-1/4'' (32mm) square tubing; 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. Floor and ceiling connections are constructed of 18-8 S, type-304, heavy-gauge stainless steel. Furnished in 10-ft (305-cm) lengths; to be
cut in field to job specifications.
Headrail (for 2042 Series only) — Extruded anodized aluminum with satin finish. Enclosed construction with sloping top. Face has
raised grip-resistant edge.
Designer's Notes: Headrails with integral curtain tracks and hooks are available for compartments without doors. Vinyl cur tains are available
as an optional accessory. Benches are available as an optional accessory for dressing compartments: 1'' (25mm) thick laminated plastic, 10''
(25cm) deep, 18'' or 24'' (46 or 61cm) wide; furnished with two stainless steel support brackets.
Commercial Hardware (standard) — Hinges, door latches, door keepers, coat hooks, and mounting brackets are constructed of 18-8 S,
type-304, heavy-gauge stainless steel with satin finish. Threaded inserts are factory installed for securing hinges on inswing doors and furnished for outswing doors. T-nuts are factory installed for securing door latch. Theft-resistant, stainless steel pin-head, torx screws are furnished for door hardware and all mounting brackets. Black rubber bumper on the latch serves as door bumper for inswing door. Balanced
hinge is adjustable to hold door of unoccupied toilet compartment par tially open or fully closed. Toilet compartment door is locked from
inside by sliding door latch into keeper. A locked compartment may be opened from outside by lifting door to disengage latch from keeper.
Track of door latch prevents inswing door from swinging out beyond stile; on outswing door, the door keeper prevents it from swinging in
beyond stile.
INSTALLATION:
Bobrick installation instructions are packed with each shipment and are available also in advance on request.
Notes:
1. Where water from showers or hose-down cleaning comes in contact with compar tments, Bobrick 2080 Series water-resistant, solid
phenolic compartments are recommended.
2. Ceiling-hung compartments require structural members (not furnished by Bobrick) in ceiling. For suggested types of ceiling support
systems, see Bobrick Advisory Bulletin TB-32.
3. Wall backing is required to secure the mounting brackets of panels, stiles, and wall posts. For suggested wall backing, see Bobrick
Advisory Bulletin TB-46.
4. Floor-anchored stiles are furnished with expansion shields and threaded rods. The expansion shields require minimum 2'' (50mm)
penetration into minimum 3" (75mm) thick structural concrete.
5. Bobrick stainless steel par tition-mounted washroom accessories are available for mounting in panels between two compartments. See
current Bobrick Catalog for description of accessories. Cutouts in panels can be pre-cut for Bobrick models at factor y if location and size
of all cutouts and Bobrick model numbers are furnished at time of order.
GUARANTEE:
Bobrick toilet partitions are guaranteed to be free from defects in material and workmanship for a period of one year from date of purchase.
Any products returned to Bobrick under this guarantee will be repaired or replaced at no charge.
SPECIFICATION:
Laminated plastic ____________________ (insert one: toilet par titions, dressing compartments, urinal screens, entrance screens) shall be
_______________ (insert one: floor-anchored, overhead-braced, ceiling-hung, wall-hung, post-to-ceiling). Stiles, panels and doors shall have
a finished thickness of 1'' (25mm). Core of panels, doors, and wall posts shall be 3-ply, 45-lb (20.4-kg) density, resin-impregnated particle
board. Stiles shall have 3-ply, 45-lb (20.4-kg) density, resin-impregnated particle board bonded to each side of 11-gauge (3.2mm) sheet steel
that serves as reinforcing core. Stiles shall have leveling device that is welded to the sheet-steel core and concealed by a one-piece, type-304,
satin-finish stainless steel shoe that is 4'' (102mm) high. Surfaces and edges shall be .050'' (1.3mm) thick, high-pressure plastic laminate
with colored face sheets and matte finish; bonding shall be done using adhesives especially formulated to prevent delamination from
moisture and heat normally existing in public washrooms. Stiles, panels and doors shall be __________ (insert color name and number from
current Bobrick Catalog). Headrails for overhead-braced compar tments shall be anodized aluminum with satin finish.
*
All door hardware
and mounting brackets shall be type-304 stainless steel with satin finish. No door hardware or mounting brackets shall be exposed on
exterior of compartments, except on outswing doors. Threaded inserts shall be factory installed for securing hinges on inswing doors and
furnished for outswing doors. T-nuts shall be factor y installed for securing door latches. Theft-resistant, stainless steel pin-head, torx screws
shall be furnished for door hardware and all mounting brackets. A coat hook shall be fur nished for each door. Hinges shall be adjustable to
hold doors of unoccupied compartments par tially open or fully closed, and shall allow a locked compartment to be opened from outside by
lifting door to disengage latch from keeper. Manufacturer's service and parts manual shall be provided to the building owner/manager upon
request.
_____________________ _ (insert one: Toilet Partitions, Dressing Compartments, Urinal Screens, Entrance Screens) shall be
_______________ Series (insert series number) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. 2040 Revised 4/07 Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2007 by Bobrick Washroom Equipment, Inc.
Loading...