5.1Takedown and installation of T-flash card ..................................... 41
5.2T-flash Card Use ............................................................................. 41
3
1 Basic Information
1.1 Brief Introduction
Thank you for selecting our GSM/GPRS digital mobile phone. You can fully
understand the usage of this phone and enjoy the sound functions and simple
operation way after reading this manual.
This color screen mobile phone is designed for GSM/GPRS network
environment. Besides basic call functions, it also provides you with numerous
functions, including dual-card mode, name card holder phone book,
personalized incoming call rings and images, 64 chord music ring tone, SMS
and MMS, shooting, video camera function, MP3 and MP4 video player, FM,
record, auto Power On/Off, task, world time, stopwatch, Bluetooth, T-Flash,
GPRS, STK, etc.
Additionally, it offers personalized human-phone interface and satisfy your
different requirement with sound function design.
This color screen and functions described in this Use Manual depend on the
network and subscribed services. So, not all menus in the phone are available,
and shortcut numbers of menus and functions may be different due to different
phones.
Our company reserves the right to make changes to the manual without any
further notification.
1.2 Safety Instruction
Please contact Telecom Sector or distribution agency to disable your
phone SIM card once your phone is lost or stolen, in this way, it can
prevent other people from using your phone.
You are required to tell IMEI code of the phone (It’s a label at the back
of the phone. You can see it by disassembling battery) when you contact
Telecom Sector or distribution agency. Please write down the code and
keep it safe for future requirement.
In order to protect your phone against nuisance use, please take some
precautions, for example:
- Set PIN code of the phone and SIM card, and change the code
quickly before others know it.
- Do not put the phone in visible places when you get out of the car.
4
You’d better carry it with yourself or put it in travel bag.
- Set call barring.
1.3 Safety Alerts and precaution
In order to ensure to use the phone safely and correctly, please read below
precautions carefully before your use.
1.3.1 General precaution
Your phone is only suitable for battery and charger approved by our
company. Or else it may cause battery leakage, overheat, explosion and
even fire.
Do not knock, vibrate or throw the phone heavily in order to avoid
malfunction, fire, overheat, explosion and fire.
Once there’re abnormal phenomena, like temperature rising, color
change, distortion during the usage, charging or save of the batter y,
please stop using it and replace it with new battery.
It may burn the skin once the liquid in battery leak to skin or clothes, if
it happened, please flush with plenty of clean water immediately and go
to hospital at once.
Please keep the battery away from the fire to avoid fire and explosion
once the battery leaks or emits strange smell.
Do not place the battery exposure to moisture, or else it may cause
overheat, fume and corrosion.
Do not use or place the battery direct under sunlight, or in hot places,
like near the car, or else, it may cause leakage and overheat, thus, reduce
the performance and shorten the lifetime.
Do not charge the battery for over 24 hours continuously.
1.3.2 Precaution for the use of charger
Please use 220AC. It may cause leakage, fire and damage to the phone
and charger once other voltage is adopted.
Do not cause short circuit to the charger, or else it may cause electric
shock, fume and damage to the charger.
Do not use the charger if the power wire is broken, or it may cause fire
and electric shock.
Please remove accumulated dust on the power plug.
5
Do not put water containers next to the power to avoid overheat, fire,
electric shock and malfunction in case the contacts with water or other
liquid.
Do not disassemble or tamper the charger, or else it may cause personal
injury, electric shock, fire and the damage of the charger.
Do not use the charger in place of high humidity, like bathroom, or else
it may cause electric shock, fire and damage of charger.
Do not touch charger, power cord and power plug with wet hand, or it
can cause electric shock.
Do not put heavy objects on power cord or change the power cord, or it
may cause electric shock and fire.
Please unplug the power socket before cleaning and maintenance.
Please hold the charger to unplug the socket, it may damage power wire
and cause electric shock and fire once pulling the power cord.
1.3.3 Cleaning and maintenance
As phone, battery and charger are not waterproof, so do not use them in
places of high humidity, as well as avoid them being wetted by rain.
Please clean the battery and charger with soft dry cloth.
Never use alcohol, thinner or solutions, like benzene, to wipe the phone.
Dirty socket can cause poor contact and power down, and even make
recharging unavailable. So, please clean it periodically.
1.3.4 Common Precaution
Mobile Phone:
Please use the phone under the environment with temperature of
5℃-40℃ and humidity of 35%-38%.
Please use the phone far away from regular telephones, TV sets, radio
sets and office automation equipment, to avoid affecting the normal use
of these equipments and mobile phone.
Battery:
Place the battery in cool and ventilated place without direct sunlight.
The battery has a limited lifespan. The usage of battery will be
shortened progressively due to frequent charging. Once the battery is
out of use after several charging, it means that its lifespan is due, and
6
Icon
Description
Signal Strength: Shows the received signal
strength. Fuller bar means stronger signal.
Receive new SMS.
Receive new MMS.
Missed call: Shows when you have missed call(s)
of SIMA/SIMB.
you shall replace it with approved model new battery.
Do not dispose old battery as household waste. Throw it to specified old
battery disposal place and follow stipulated instructions for disposal.
Charger:
Do not charge under following conditions:
--place with direct sunlight
--place with ambient temperature less than 5℃or over 40℃, wet or dusty
place with strong vibration (it may cause malfunction);
--place near electrical appliance (it may affect the image and sound) like
TV set, radio, etc.
2 Before Use
2.1Name and Description of Individual Part
2.1.1 Technical Parameter
Size (Length × Wide × Thickness)
Weight:
Battery capacity:
Duration of standby time:
Duration of talk time:
2.1.2 Icon
There may be some icons appearing under standby interface. Please refer to the
following for detailed description:
7
Alarm clock is set to On.
Incoming Call Alert Types: Ring only, Vibrate
only (long press the # key to activate or
deactivate the silent mode in idle mode), Vibrate
and Ring, Vibrate then Ring.
Indicates battery level.
Turn on Bluetooth handset.
Keypad is locked.
2.2 Key Description
1. Power/End key
(1) Long press the Power key to switch on the phone.
If you switch on the phone and there’s no SIM card, the phone will prompt you
to insert SIM card. The phone will check if the SIM card is available after SIM
card is inserted.
Then, the following prompts will appear on the screen one by one:
Enter PIN——it appears if you’ve set password to lock the SIM card.
Enter phone password——it appears if you’ve set password to lock the phone.
Search for network——the phone will search for network till it finds proper
network
(2) Long press the Power key to switch off the phone.
(3) Press the End key to end the call or reject the call; in other cases, press the
End key can turn back to the main screen quickly.
2. Dial key1/2: Press after dialing to connect by SIM1/2 card.
In idle mode, press this key to display your recent call records of all SIM cards.
3. Left soft key/Right soft key: Implement the functions shown in the lower
left/right hand corner.
4. Navigator keys: Press the up/down/left/right direction in menu to scroll,
browse or in edit page to move cursor. From standby mode, press the up/
down/left/right direction to enter the different function interface (as defined in
the menu Settings/Phone settings/Dedicated key).
8
5. OK key: In idle mode, press to enter the main menu.
In general situation, it is identical with the left soft key.
6. Alphanumeric keys: Be used to dial and input text in edit interface.
From standby mode, long press “2” to “9” key to dial speed dials numbers (as
defined in the menu [Phonebook/phonebook settings/Speed dial]).
Long press the “0” key to open or close the torch light in idle mode.
7. # key: In idle mode, long press the # key to activate or deactivate the silent
mode.
2.3 Charge for Battery
Connect the charger with power.
Insert the end of the charger into the bottom of the phone (Note: the
arrowhead shall be upward).
Then, power indication icon on the screen, which means that the battery
is under charging. If the phone is overused under low battery, then
charging indication icon will be displayed after the charging has been
done for some time.
If the power indication icon in the upper right corner is fully displayed
without flashing that means it is full. If the phone is switched off during
charging, there is image to indicate the charging is over. This process
needs 3-4 hours. It’s normal that the battery, phone and charger with AC
electrical plug once the battery is fully charged.
Note:
Always keep the battery in ventilated place with the temperature from +
5℃ to +40℃ during charging, and make sure to use the charger provided
by manufacturer. It may cause danger once unapproved charger is used
and it may invalidate any approval or warranty.
If the phone switches off automatically or there’s “Battery Low”
displayed on the phone, please charge to the battery as quickly as
possible. The phone will reduce charging time automatically if the
battery power isn’t used up before charging.
The duration of standby time and talk time offered by manufacturer are
based on ideal working environment. In actual, however, the working
time of battery changes according to network condition, working
9
environment and using method.
Make sure the battery is installed properly before charging and it’s
forbidden to remove the battery during charging.
Please disconnect the charger and phone with power. The phone begins
charging again when the power loss reaches certain extent after
overcharging lasts for quite a long time (about 5-8 hours). We suggest
you don’t do this, as it will influence the performance and lifetime of
the battery.
2.4Connecting to network
2.4.1 SIM card
Make sure that you’ve inserted available SIM card into the phone before your
use. SIM card is the key to enter digital GSM net work.
All information related with establishing network connection and calling record
initiate are saved in metal area in SIM card. Meanwhile, there’re other
information saved in the SIM card, including name and number saved in phone
book and SMS. The SIM card can be removed from your phone and inserted to
any GSM phone (the new phone will read SIM card automatically).
Never touch metal area for the SIM card to avoid information loss or damage of
the card. Keep SIM card if the phone is connected to external power, or else, the
SIM card will be damaged.
2.4.2 Insertion and Removal of SIM card
SIM card is placed in sty like a credit card, so please take it out carefully before
installing in the phone.
Switch off the phone and remove the battery and other external power
This phone supports to insert dual SIM cards at most, the place of card
1/2 is decided by options in menu (please refer to “Settings” for “Dual
SIM settings”).
2.4.3 Unlock of SIM card
SIM card uses PIN (personal identity number) code for protection against
unauthorized use. You are required to input PIN code to unlock the SIM card
every time the phone is switched on once your phone enables this function, then
you can call out and answer incoming calls. Users can also choose to remove
SIM card protection (please refer to Section 3.12.4 Security settings): in this
10
case, SIM card can’t be protected against unauthorized use.
Long press the Power Key to switch on the phone.
Input PIN code, press the Right soft key ‘Clear’ to clear incorrect input
and press OK to enter. For example, if PIN code is set as 1234, then you
should input: 1 2 3 4
If incorrect code is keyed in for three times, SIM card will be locked. The phone
will require you to key in PUK1 code for unlocking. Please do not key in at
random if you don’t know PUK1 code, you shall send SIM card to network
operator for assistance. Please refer to section 3.12.4 Security settings.
Note: Your network supplier will set a standard PIN code (4 to 8 digits) for your
SIM card. You shall change the code to your personal password as soon as
possible. Please refer to section 3.12.4 Security settings for details.
2.4.4 Unlock of the phone
You can set password to protect your phone against unauthorized use. You are
required to key in phone code (if you’ve set password protection) to unlock the
phone every time the phone is switched on once your pone enables this function,
then you can make calls or answer incoming calls. Users can also choose to
remove password protection (please refer to section 3.12.4 Security settings); in
this case, the phone can’t be protected against unauthorized use.
Key in phone password, press the Right soft key ‘Clear’ to clear incorrect input
press OK to enter. For example, if the phone password is set as 1122, then you
shall key in: 1122.
Please contact your retailer or local authorized maintenance service center to
unlock the phone password once you forget it.
2.4.5 Connecting to network
The phone will search for available network automatically (Searching for
network is displayed on the screen) once the SIM card is unlocked successfully.
Name of network supplier will appear on the screen once the phone searches for
available network.
Note: IF EMERGENCY is displayed on the screen, it means that your phone is
out of the normal network coverage, but you can also make emergency calls
according to the signal strength.
11
2.4.6 Dial calls
You’re allowed to make calls or answer incoming calls once name of network
supplier appears on the screen. The signal bar in upper left corner represents the
strength of network signal. Moving in a small range can improve your calling
quality as the calling may be interfered by barriers greatly.
2.4.7 Dial domestic calls
In standby mode, press the corresponding numeric keys to input phone number
that you want to dial and press Dial Key to make calls. Please press the Right
soft key ‘Clear’ to delete characters once the phone number needs to be changed.
Dialing animation will be displayed on the screen when dialing. The call status
information will be displayed after the recipient answers the phone. There’s an
alert tone when it gets through (it needs network support) if this function is
enabled.
Please press the End Key to end the call once it’s over.
Zip code Phone number Dial key
2.4.8 Dial extension of fixed phones
Some extensions of fixed phones can’t be got through, and you shall only dial
the telephone exchange, and then dial the extension number. The phone can
finish all dialing and dial the extension automatically when you insert pause
character “P” between telephone exchange and extension number. The way of
inputting “P” is to press and hold * key, and then symbol “P” appears on screen.
Zip code Telephone exchange P Extension Dial key
Example of the use of pause character:
For example, if there’s a voice mailbox system, which is used through dialing
way in 8880000 numbers, the number of mailbox is 6666 and the password is
8888, then you can follow the way below to dial:
8880000 P 6666 P 8888
The first part of this number is used to dial voice mailbox system.
It will send 6666 to select mailbox once the phone is answered.
The second pause character will delay for 5 seconds before password
8888 is sent out (the former “P” represents to get through, the latter “P”
represents to delay for 5 seconds).
12
2.4.9 Dial international calls
Press *key under standby status till prefix symbol “+” appears on the screen
when dialing international calls. It allows you to dial a number in any country
once you don’t know the international prefix symbol (e.g.: it’s 00 for China).
Key in the country code and complete phone number after prefix symbol
appears. The country codes follow general practices, the country code of
Germany is 49, Britain is 44, Swiss 46, etc.
“0” before the area code shall be removed before dialing, just as dialing
international calls. For example, you shall dial like this if you need to dial
service hotline from other countries:
+86 21 114
+ Country code Complete phone number Dial key
2.4.10 Dial call in the list
Every phone number you dialed and received are saved in a list in the phone,
recent dialed and received phone numbers are placed on the top of the list
(Please refer to Section 3.7.1 Section Call history). Every phone number is
classified based on Dialed Calls, Received Calls and Missed Calls. The phone
also provides you with All Phone Items for you to view all calling record. Old
phone numbers will be deleted automatically once the phone number list is full.
2.4.11 Emergency calls
You can call emergency services if you are within the network coverage (you
can check it by viewing the network signal strength bar in the upper left corner).
If the network supplier doesn’t provide roaming service, then “EMERGENCY”
appears on the screen, which means you can only call these calls. You can dial
emergency calls within the network coverage even if there’s no SIM card.
2.4.12 Answer calls
You shall press Dial Key to enter answer. You can also press the key on the
headset to answer calls once the headset is inserted. Hence, you can set Auto
Answer to On once it’s inconvenient for you to press keys, and the phone
answers automatically after vibration and ring or vibration lasts for 5 seconds
once the headset is inserted.
2.4.13 Call history
The phone saves the record of your last call and duration since the phone is used
13
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.