Bluworld WWLVCRCP User Manual

CLASSIC QUARRY NOJOQUI

& HORIZON FALLS

Installation Manual

IMPORTANT – RETAIN FOR FUTURE REFERENCE – READ CAREFULLY

• Try to position your fountain above or near an electrical outlet.

• When considering the location of your fountain, please consider making it easily accessible for maintenance (e.g.

adding water, cleaning etc.). Avoid delicate surfaces that could be damaged by splashing.

• Consider the surface on which your waterfall will be placed. This feature can be mounted on sheetrock with

wood studs, tile, brick or concrete. (No mounting hardware is included for masonry installations). Due to the
weight of this fountain, it is necessary to mount directly into at least one wood stud. You MUST use the provided
EZ Anchors™ (J) for any screw that does not hit a stud.

• Mount indoors only. It is not recommended to place your fountain in direct sunlight.

• ** It is critical that your waterfall is level as this will ensure even water flow. **

• Assemble as near as possible to the point of installation. Take extreme care when lifting to avoid

personal injury or damage to the product.

• This product contains small items and plastic bags. Please be aware of the danger to young children.

• Assistance in mounting your fountain is required. You will need 2-3 people.

635 W. Michigan Street Orlando, FL 32805 · PH 407-426-7674 · Fax [phone]

Page 1 of 8

A. Bracket Template 1 each

B. Stone Wall Bracket 1 each

C. Remote 1 each

D. Reservoir Wall Bracket 1 each

E. Water Disperser 1 each

F. Water Diffuser 1 each

G. Trim Kit (your color may be different) 1

H. Pump Assembly w/Flow Valve 1 each

I. River Rocks 1 each

J. Hardware Bag with scrubby pad

K. LED Light Kit with cord 1 each

L. Reservoir 1 each

M. Pocket Clips 2 each

N. Rock Tray 1 each

O. EVA Reservoir Pads 2 each

Parts List

Section 1: Initial Prepping

Not Shown - Classic Quarry Stone

each

1. Carefully remove and inspect all your Classic Quarry components from its shipping carton. Do not install or

operate unit if an y part s are d amag ed. Pl ease ret ain all p ackagin g u ntil your un it is in stall ed cor rect ly and
running successfully. You may leave the stone on the pallet until ready to hang.

2. It is very important to rinse your sto ne clean of an y dust or chips th at ma y have acc umulated duri ng shipp ing prior
to assembling your fountain.

3. Tools required: Level, Pencil, stud finder, drill with Phillips bit, Phillips Sc re wdri ve r, and Measuring Tape.

4. The use of distilled water is strongly su ggested You wil need 5 ga llons of distilled water for Nojoqui Falls and 5

gallons for Horizon Falls.

635 W. Michigan Street Orlando, FL 32805 · PH 407-426-7674 · Fax [phone]

Page 2 of 8

Fig 2.1

Fig 2.2

Fig 2.3

Fig 2.4

Section 2: Mounting the Wall Brackets

1. Your Nojoqui F alls fountain is 58” ta ll x 25.5” wide
the Horizon Falls fountain is 33” tall x 51” wide.
Determine where on the wall the fountain will be
mounted. You may wish to block out the
dimensions with low t ack or painters m asking tape
for reference. T he fountain must be mounted into
studs, wood or m etal. Using the stu d finder locate
and mark the position of the vertica l and horizontal
studs within the blocked out installation area.
Once the studs have been located, the brackets
can be installed.

2. Mark the center of the fountain’s width (Noj oqui Fal ls is 12.75” - half the 25. 5”overall f ountain width) and (Hori zon
Falls center is 25.5” – half the 51” overall width) for referenc e. Using your level mark this line vertic ally within the
installation area.

3. Identify the Bracket Template (A) from the fountain com ponents. The top of the bracket (A) will rest
exactly 4” down from the overa ll heig ht of your fountai n. Using t he cent er mark of the f ountain’s width
place the Bracket Tem plate‘s (A) upper k eyhole so you can see the center line through th e hole. The
keyholes should be in this position (Fig 2.1). Mark the top keyhole.

4. Using a Phillips screw driver and a sm all scr ew from your Hardware B ag (J) s et the scr ew in the wall so th at ¼” is
left protruding. Hang the Bracket Template (A) from this screw (Fig 2.2) making certain the keyhole is in the
position shown in Fig 2.1.

5. Using the level make certain the Bracket Template (A) is vertically level and mark the placement of the lower
keyhole. Remove the Bracket Template (A).

6. Again using a Phillips screw driver and a small sc rew, set the screw in the lower keyhole m ark so that ¼” is left
protruding.

7. Hang the Stone Wall Bracket (B) from the center keyhole on the upper scr ew. Note the posit ion of the m arked wall
studs through the numerous bracket holes. (Fig 2.3)

8. Place the level on the top of the Stone W all Bracket (B) insuring it is level (Fig 2.3) . Mark the holes that align with
the wall studs. The i dea l br ac ket installation would incl ude s cr e ws loc at ed at t he b r ack et’s left top an d bo ttom, right
top and bottom and center. If you do not have s tuds at these locations you will ne e d to us e the EZ Anc hors ™ ( J ) to
complete the Stone W all Bracket (B) installation at t hese locations. Remove the keyhole screw as it will int erfere
with the installation of the stone.

9. Repeat this procedure for the Reservoir Wall Bracket (D) (Fig 2.4). Remove the keyhole screw when finished.

635 W. Michigan Street Orlando, FL 32805 · PH 407-426-7674 · Fax [phone]

Page 3 of 8