BLU-JET LEGACY Assembly And Operators Manual

TM

A

LL

T

ERRAIN

I

NJECTION

LEGACY

Assembly
and Operators
Manual

Manual Number
0605010
Rev. 2-19-18 $20.00 Net.

Thurston Manufacturing Company • 1708 H Ave • Box 218 • Thurston, Nebraska, 68062-0218

Phone: [phone] • E-mail: [e-mail]

Design specications and features as described are subject to change without notice. BLU-JET is a registered trademark of Thurston Manufacturing Company, Thurston NE.

/BLU-JET

@BLU-JET01

/SIronWorks

@SIronWorks

LEGACY

Meter Assembly GDI200A With Dual Impellicone Manifold,

(66000129) 15 Row 30

66000129

21

NOTE: GENERIC EXPLODED

VIEW. CONSULT BOTTOM MANIFOLD
DIAGRAM FOR HOSE BARB AND PLUG
PLACEMENT.

13

16

15

22

19

Extend
to Gauge

2

Extend

to Knives

2E

18

18

2D

15

15

16

16

2E

2C

2B

16

16

15

15

2A

17

17

20

20

From
Meter

19

19

14

16

14

109

Table of Contents

LEGACY

Manual Number:

0605010

Rev. 2-19-18

Introduction------------------------------------------------------------------------------------------------------- 1
Deliver--------------------------------------------------------------------------------------------------------------- 4
To The Owner----------------------------------------------------------------------------------------------------- 5
Warranty------------------------------------------------------------------------------------------------------------ 6

Safety--------------------------------------------------------------------------------------------------------------- 7

Operating Instructions---------------------------------------------------------------------------------------- 11
Anhydrous Ammonia Operating Instructions--------------------------------------------------------- 19
Coupler Operation---------------------------------------------------------------------------------------------- 22

Parts----------------------------------------------------------------------------------------------------------------- 23

Emergency Fresh Water Tank--------------------------------------------------------------------------------- 23
Main Frame-------------------------------------------------------------------------------------------------------- 24
Primary Wing Right-hand--------------------------------------------------------------------------------------- 26
Primary Wing Left-hand----------------------------------------------------------------------------------------- 28
Secondary Wing Right-hand----------------------------------------------------------------------------------- 30
Secondary Wing Left-hand------------------------------------------------------------------------------------- 32
Secondary Wing Right-hand 3’-2”---------------------------------------------------------------------------- 34
Secondary Wing Left-hand 3’-2”------------------------------------------------------------------------------ 35
Dual Wheel Lift---------------------------------------------------------------------------------------------------- 36
Single Wheel Lift-------------------------------------------------------------------------------------------------- 38
Tongue--------------------------------------------------------------------------------------------------------------- 40
Secondary Wing Stop and Straight Extension------------------------------------------------------------ 42
Secondary Wing Extension To 50 ft.-------------------------------------------------------------------------- 43
Pin Adjust Gauge Wheel---------------------------------------------------------------------------------------- 44
Decals--------------------------------------------------------------------------------------------------------------- 45
Legacy 38’, 42’, 47’, 52’ Toolbars----------------------------------------------------------------------------- 46
Legacy Hydraulics 38’, 42’, And 47’--------------------------------------------------------------------------- 48
Hose Kit 38’, 42’, And 47’---------------------------------------------------------------------------------------- 52
Legacy Hydraulics 52’-------------------------------------------------------------------------------------------- 54
Hose Kit 52’--------------------------------------------------------------------------------------------------------- 57
Stagger Brackets Offset 6 x 6 Mounting-------------------------------------------------------------------- 60
Coulter, Super 1200 Flex and Shank------------------------------------------------------------------------ 62
Nurse Tank Hitch PKG00234---------------------------------------------------------------------------------- 63
Nurse Tank Hitch PKG00247 Low Mounting--------------------------------------------------------------- 64
Auto-Lok Nurse Tank Hitch AAM2870----------------------------------------------------------------------- 65
Blades--------------------------------------------------------------------------------------------------------------- 66
SealPro II and SealPro SKF----------------------------------------------------------------------------------- 67
Hitches--------------------------------------------------------------------------------------------------------------- 74
Jack------------------------------------------------------------------------------------------------------------------ 75
Shanks-------------------------------------------------------------------------------------------------------------- 76
Row Clamps------------------------------------------------------------------------------------------------------- 77
Manual Holder----------------------------------------------------------------------------------------------------- 80
Impellicone Mounting Hardware------------------------------------------------------------------------------ 81
SuperShooter III--------------------------------------------------------------------------------------------------- 82
SuperShooter III Single Assembly Less Distribution (66000136)------------------------------------- 83
SuperShooter III Add-on Dual Assembly Less Distribution (66000137)---------------------------- 84
GDI W/Pump Distribution (Rear Mount) (Bundle 20200119)------------------------------------------ 88
GDI W/Twin Pump Distribution (Rear Mount) (Bundle 20200121)----------------------------------- 96
Dual Impellicone Manifold Distribution Bundles---------------------------------------------------------- 105
MaxPac AR700 Parts and Assembly------------------------------------------------------------------------ 113
MaxPac Basket Mount Arm------------------------------------------------------------------------------------ 114
Coulter Extension Kit (9-7/8”)----------------------------------------------------------------------------------- 115
MaxPac Assembly------------------------------------------------------------------------------------------------- 116
Torsion Arm Basket Parts and Assembly------------------------------------------------------------------- 118
Torsion Arm Basket Flat Mounting---------------------------------------------------------------------------- 121
Residue Managers Parts and Assembly-------------------------------------------------------------------- 122
Light Kit/SMV------------------------------------------------------------------------------------------------------ 130
GDI Lift Kit---------------------------------------------------------------------------------------------------------- 132
Hub and Spindle Assembly------------------------------------------------------------------------------------- 133
Hydraulic Repair Kit---------------------------------------------------------------------------------------------- 136
Tie-rod Cylinder Disassembly-Assembly Procedure----------------------------------------------------- 137

Torque Specications-------------------------------------------------------------------------------------------- 138
Specications------------------------------------------------------------------------------------------------------ 139

Assembly................................................................................................................................ 141

Main Frame and Primary Wings------------------------------------------------------------------------------ 141
Secondary Wings------------------------------------------------------------------------------------------------- 142
Dual Wheel Lift---------------------------------------------------------------------------------------------------- 143
Single Wheel Lift-------------------------------------------------------------------------------------------------- 146
Primary Wing Gauge Wheel------------------------------------------------------------------------------------ 148
Center Section Wheel Lift Linkage--------------------------------------------------------------------------- 152
Tongue Mounting------------------------------------------------------------------------------------------------- 155
Tongue Linkage--------------------------------------------------------------------------------------------------- 156
Bolt-on Cylinder Lug--------------------------------------------------------------------------------------------- 159
Primary Wing Cable Release---------------------------------------------------------------------------------- 160
Hitch and Safety Chain------------------------------------------------------------------------------------------ 161
Jack------------------------------------------------------------------------------------------------------------------ 162
Hose Holder and Hose Tender-------------------------------------------------------------------------------- 163
Turnbuckle Wrench----------------------------------------------------------------------------------------------- 164
Hitch Storage------------------------------------------------------------------------------------------------------ 165
Manual Holder----------------------------------------------------------------------------------------------------- 166
Stagger Brackets-------------------------------------------------------------------------------------------------- 167
Primary Wing Linkage------------------------------------------------------------------------------------------- 168
Secondary Wing Linkage--------------------------------------------------------------------------------------- 169
Secondary Wing Latch Standard Wing---------------------------------------------------------------------- 170
Secondary Wing 28” Extension Kit---------------------------------------------------------------------------- 171
Secondary Wing Angled Stagger------------------------------------------------------------------------------ 172
Hose Holder Placement----------------------------------------------------------------------------------------- 173
Hydraulics 52’------------------------------------------------------------------------------------------------------ 174
Hydraulics 38’, 42”, 47’------------------------------------------------------------------------------------------ 185
Pin Adjust Gauge Wheel---------------------------------------------------------------------------------------- 197
Nurse Tank Hitch Single PKG00234------------------------------------------------------------------------- 198
Nurse Tank Hitch Single Low Mounting PKG00247------------------------------------------------------ 200
SuperShooter III Add-on Parts (66000136)---------------------------------------------------------------- 202
SuperShooter III Add-on Parts, Dual (66000137)--------------------------------------------------------- 206
Coulter--------------------------------------------------------------------------------------------------------------- 210
Shank---------------------------------------------------------------------------------------------------------------- 212
Spring Cushion---------------------------------------------------------------------------------------------------- 214
Light Kit-------------------------------------------------------------------------------------------------------------- 216
SMV------------------------------------------------------------------------------------------------------------------ 220
Safety Tank--------------------------------------------------------------------------------------------------------- 221
Depth Collars------------------------------------------------------------------------------------------------------ 222
Decals--------------------------------------------------------------------------------------------------------------- 223
Hydraulic System Charging------------------------------------------------------------------------------------ 225
Folding Toolbar--------------------------------------------------------------------------------------------------- 226
Depth Control (66000148)------------------------------------------------------------------------------------- 227

Row Spacing Layout------------------------------------------------------------------------------------------- 237

1

LEGACY

Introduction

Welcome to Thurston Manufacturing Company. Our goal is to provide

quality products and services to our customers. The company’s BLU-JET
products have a reputation for quality, excellence in design and proven
durability. Energetic, resourceful and continuous improvement goals in
Environmental, Safety, Quality, Production and Engineering keep our

rm at the cutting edge of technology.

We hope your BLU-JET equipment will give you years of service.

Read this manual carefully. It will instruct you on how to operate and

service your machine safely and correctly. Failure to do so could result
in personal injury and/or equipment damage.

SAFETY INFORMATION

Indicates an imminently hazardous situation that, if
not avoided, will result in death or serious injury.

The sign will have the color combination of red and
white.

Indicates a potentially hazardous situation that, if
not avoided, could result in death or serious injury.

The sign will have the color combination of orange
and black.

Indicates a potentially hazardous situation that, if

not avoided, may result in minor or moderate injury.
The sign will have the color combination of yellow
and black.

NOTE: Indicates a special point of information.

Carefully read and follow all safety signs. Reinstall safety signs that
are damaged or missing.

DANGER

WARNING

CAUTION

Right-hand and left-hand sides of the implement are determined by

facing in the direction the implement will travel when going forward.

2

LEGACY

Introduction

General Information:

The BLU-JET Legacy Commercial Class Fertilizer Injection Applicator
achieves a new performance dimension for high acre, high rate applications.
The BLU-JET Legacy can easily be congured for a number of operations
including Pre-Plant, Side-Dress, and StripTill applications with anhydrous,
liquid, dry, or dual placement fertilizer injection.
The Legacy was designed to be used in combination with BLU-JET’s
Super 1200 Coulter, MaxPac 700 AutoReset shank mounting, residue managers,

SealPro disc sealers, torsion arm rming baskets and BLU-JET’s complete

line of shank mountings.

Warranty is provided for customers who operate and maintain their equi pme nt

as described in this manual. Warranty registration is accomplished by
the dealer completing and forwarding the WARRANTY REGISTRATION FORM
to Thurston Manufacturing Company. It is in your best interest to insure that
this has been done.

For your convenience we have four easy ways to register your warranty.

• Call our toll free number and ask for warranty registration.

1-800-658-3127

• Register on-line at: www.BLU-JET.com

• Complete and mail this Product Registration form to:

Attn: Thurston Manufacturing Company
Product Registration
PO Box 218
Thurston, NE. 68062

• Email a copy to: [e-mail]

Thurston Manufacturing Company Warranty does not cover the following:

1) Cleaning, transporting, mailing and service call charges.

2) Depreciation or damage caused by normal wear, accidents,
improper protection or improper use.

The Serial Number
is located from the
rear of the tool bar
on the right-hand
side behind the

Tractor side

Record your implement model and serial number in the space provided be-

low. Your dealer needs this information to give you prompt, efcient service

when you order parts.

MODEL NO.__________________________

SERIAL NO.__________________________

DATE PURCHASED___________________

tongue pull plate.

3

LEGACY

Dealer Checklist

To The Dealer:

Inspect the implement thoroughly after assembly to be certain it is
functioning properly before delivering it to the customer. The following
checklist is a reminder of points to cover. Check off each item as it is
found satisfactory or after proper adjustment is made.

PRE-DELIVERY CHECKLIST

1. All hardware properly tightened

2. Lubrication of grease ttings

3. All decals properly located and readable

4. Other adjustments for machine level height, etc.

5. Overall condition (touch up any scratches, clean and
polish)

6. Operator’s manual

DATE SET UP_______________________________
SIGNATURE________________________________

DELIVERY

Review the operator’s manual with the customer. Explain
the following:

1. Safe operation and service

2. Correct machine installation and operation

3. Daily and periodic lubrication and maintenance
4 Daily and periodic inspections

5. Trouble shooting

6. Storing machine

7. Thurston Manufacturing Company parts and service

8. Have the customer write the machine model and serial
number in space provided in manual introduction.

9. Give customer the operator’s manual and encourage
the customer to read the manual carefully.

10. Completion and mailing of warranty registration
form.

DATE DELIVERED__________________________
SIGNATURE_______________________________
MODEL NO.________________________________
SERIAL NO.________________________________

4

LEGACY

To The Owner

Thank you for your recent purchase of a new BLU-JET

implement. The primary objective of Thurston Manufacturing
Company is to build and provide you with a quality product.
However, in the event that a problem does occur, it is imperative

that your warranty registration is on le in order to accurately
respond to your specic service circumstances.

For your convenience we have four easy ways to register
your warranty:

For your convenience we have four easy ways to register your warranty.

• Call our toll free number and ask for warranty registration.

1-800-658-3127

• Register on-line at: www.BLU-JET.com

• Complete and mail this Product Registration form to:

Attn: Thurston Manufacturing Company
Product Registration
PO Box 218
Thurston, NE. 68062

• Email a copy to: [e-mail]

This manual has been prepared to assist you in the assembly
of your new machine and contains information pertaining to
safety, operations and all of its parts. Our personnel in sales
and service are always available to assist you when questions
arise concerning the assembly or operations of your tool bar.

When ordering parts, please refer to part numbers and
descriptions as listed throughout this book. All parts and
whole goods will be shipped FOB Thurston, Nebraska. Or
FOB your regional distributor. Always check merchandise
immediately upon receipt for damage or shortage. Note any
discrepancy on carrier’s bill of lading and notify Sender within
10 days. Returned goods will be subject to a 15% restocking
charge. Thurston Manufacturing Company reserves the right

to make improvements and modications on equipment

without obligation to change previously built equipment. All
prices are subject to change without notice.

5

LEGACY

Limited Warranty

Thurston Manufacturing Company warrants each new BLU-JET machine

primary framework to be free from defects in material and workmanship for a period

of ve (5) years, normal wear of wearing parts excepted. Thurston Manufacturing

Company further warrants each new BLU-JET product to be free from defects in
material and workmanship, normal wear of wearing parts excepted, for a period
of one (1) year. All accessories purchased and resold by Thurston Manufacturing
Company will be warranted according to their respective manufacturer. Tires on
BLU-JET equipment are warranted through their respective tire manufacturers and
their network of dealers in your local area.

Warranty begins from date of delivery to the original purchaser and applies

to all new BLU-JET products that have not been altered and are being used for the

intended purpose. Negligence, abuse or modication of equipment manufactured

by or purchased and resold by Thurston Manufacturing Company will void this
warranty.

The obligation of Thurston Manufacturing Company to honor this warranty
is limited to the repair or replacement of defective merchandise, to the original
purchaser, subject to inspection of equipment in question by an authorized Thurston
Manufacturing Company sales or service technician. In the USA, freight of warranty
replacement parts including main frame centers and wings will be prepaid for a
period of one (1) Year by Thurston Manufacturing Company. Shipments of repaired
or replaced parts including main frame centers and wings after one year will be paid
by the customer.
Return of defective goods must be made within thirty (30) days of failure to
Thurston Manufacturing Company, Thurston, Nebraska USA or to the nearest
authorized BLU-JET Distributor or Rep Sales and service outlet.

Thurston Manufacturing Company will not be held responsible for any repair
charges made by customers without prior written consent and prior equipment
inspection by an authorized Thurston Manufacturing Company sales or service
technician.
This warranty shall not be interpreted to render liability for injury or damages
of any kind, direct, consequential or contingent to person or property. This warranty
does not extend to loss of crops, economic and/or commercial loss, loss because
of delay in crop production or any expense incurred for labor, supplies, substitute
machinery, rental or for any other reason. This warranty is subject to any existing
condition of supply, which may directly affect Thurston Manufacturing Company’s
ability to obtain materials of manufacture and delivery of replacement parts.

Thurston Manufacturing Company reserves the right to make improvements

in design and changes in specications at any time without incurring any obligation

to owners of units previously sold.
No one is authorized to alter, modify or enlarge this warranty nor its exclusions,
limitations and reservations. Thurston Manufacturing Company makes no
representations or warranties, expressed or implied (including implied warranties

of merchantability and tness), except for those set forth in Thurston Manufacturing

Company’s current applicable published warranty policies and procedures.

Layton W. Jensen, President 022398\mgmt

6

LEGACY

Safety

RECOGNIZE SAFETY INFORMATION

• This is the safety-alert symbol. When you see his symbol
on your machine or in this manual, be alert to the
potential for personal injury. Follow recommended
precautions and safe operating practices.

FOLLOW SAFETY INSTRUCTIONS

• Carefully read all safety messages in this manual and

on your machine safety signs. Keep safety signs in good
condition. Replace missing or damaged safety signs.

• Learn how to operate the machine and how to use

controls properly.

• Do not let anyone operate without instruction.

• Keep your machine in proper working condition.

• Unauthorized modication to the machine may

impair the function and/or safety and affect machine life.

PROTECT CHILDREN AND BYSTANDERS

• Before you back, LOOK CAREFULLY behind for

children.

• Clear area of children, pets and bystanders.

HIGHWAY AND TRANSPORT OPERATIONS

Adopt safe driving practices:

• Keep the brake pedals latched together at all times.

NEVER USE INDEPENDENT BRAKING WITH MACHINE
IN TOW AS LOSS OF CONTROL AND/OR UPSET OF
UNIT CAN RESULT.

• Always drive at a safe speed relative to local

conditions and ensure that your speed is low enough
for a emergency stop to be safe and secure. Keep
speed to a minimum.

• Reduce speed prior to turns to avoid the risk of

overturning.

• Avoid sudden uphill turns on steep slopes.

• Always keep the tractor or towing vehicle in

gear to provide engine braking when going downhill.
Do not coast.

• Do not drink and drive.

• Comply with state and local laws governing highway

safety and movement of farm machinery on public roads.

• Use approved accessory lighting and necessary

warning devices to protect operators of other vehicles
on the highway during daylight and nighttime transport.

• The use of ashing amber lights is acceptable in most

localities. However, some localities prohibit their use.
Local laws should be checked for all highway lighting
and marking requirements.

• When driving the tractor and equipment on the road

or highway under (20 mph max.) (32 kmph max.) at night or

during the day, use ashing amber warning lights
and a slow moving vehicle (SMV) identication emblem.

7

LEGACY

Safety

HIGHWAY AND TRANSPORT OPERATIONS

• Plan your route to avoid heavy trafc.

• Be a safe and courteous driver. Always yield to oncoming
trafc in all situations, including narrow bridges,

intersection, etc.

• Be observant of bridge loading ratings. Do not cross

bridges rated lower than the gross weight at which you
are operating.

• Always operate equipment in a position to provide

maximum visibility at all times. Makes allowances for
increased length and weight of the equipment when
making turns, stopping the unit, etc.

TRANSPORT SAFETY

• A safety chain will help control drawn equipment

should it accidentally separate from the drawbar.

• Attach the chain to the tractor drawbar support or

other anchor location. Provide only enough slack in
the chain to permit turning.

• Use hydraulic cylinder transport lockup during road

transportation.

• Maximum road speed is 20 m.p.h.

AVOID HIGH PRESSURE FLUIDS

• Escaping uid under pressure can penetrate the skin

causing serious injury.

• Avoid the hazard by relieving pressure before

disconnecting hydraulic or other lines. Tighten
all connections before applying pressure.

• Search for leaks with a piece of cardboard.

• Protect hands and body from high pressure uids.

• If an accident occurs, see a doctor immediately.

DISPOSE OF FLUIDS PROPERLY

• Improperly disposing of uids can harm the

environment and ecology. Before draining any

uids, contact your local environmental agency

for the proper waste disposal methods.

• Use proper container when draining uids. Do

not use food or beverage containers that may
mislead someone into drinking from them.

• DO NOT pour oil into the ground, down a drain, or

into a stream, pond, or lake. Observe relevant
environmental protection regulations when disposing
of oil and other harmful waste.

8

LEGACY

Safety

Observe Safety Signs

AP 2234-7-98

AP 2914

AP 2222 8-90

AP 2469-7-98

AP 2483-8-98

9

LEGACY

Safety Decals

AP 2972

AP 2227

AP 2974

AP 2973

AP 2975

10

LEGACY

Maximum Vertical Drawbar Load (lbs)

Drawbar Position

Operating Instructions

Hitch

NOTE:

Implement
hitch weights
are designed
to match
tractor size
ranges.
Check the
following
chart to

conrm your

particular
implement
specica-

Tractor to
tool bar
connection

1. The tractor must be equipped
with a drawbar and a draw­ bar safety chain clevis. For
rigid frame tractors equipped
with swinging drawbar, the
drawbar must be located in a

xed position in the center of

the tractor. Refer to your
tractor operators manual for
drawbar adjustment and
drawbar operating instructions.

PTO

Power

Category (HP) Short Regular Extended

0 ≤ 38 1,574 1,124 787
1 ≤ 64 2,698 1,798 1,349
2 ≤ 154 4,946 3,372 2,473
3 ≤ 248 6,070 4,046 2,922
4 ≤ 402 7,418 4,946 3,597
5 ≤ 671 10,116 6,744 N/A

Generic Photo

2. Before connecting the tool bar to the tractor drawbar, raise the
tractor three point hitch (if equipped) to prevent interference
between the implement and the tractor.
Connect the tool bar to tractor drawbar ONLY. DO NOT connect
the tool bar to any other part of the tractor. Connect the tool bar
clevis to the tractor drawbar with hitch pin. Install the safety
chain through the tractor drawbar support bracket.

Safety
hitch pin

Safety
chain

3. Always use a safety hitch pin of the correct diameter. Make sure
that the hitch pin is locked in place with a safety type lock pin or
other locking device.

4. Always use a safety chain between the toolbar and the tractor.
Install the chain to the tractor drawbar support bracket. Support
the center of the chain with a clevis installed to the tractor
drawbar.

WARNING

WARNING: In case the tractor hitch pin is lost during transport-

ing. The safety chain must be attached between the implement
and tractor to prevent separated implement from running freely
and causing damage or injury.

WARNING

WARNING: Do not move articulated tractor steering wheel

until everyone is clear of the equipment. Moving the steering
wheel can swing or move attached equipment which could
cause serious personal injury.

WARNING

WARNING: Tractor drawbar must be in a xed position before

transporting implement. Implement will sway or slam against
tractor resulting in equipment damage or injury to personnel.

11

LEGACY

Operating Instructions

Remote
hydraulic

NOTE:

Always
connect the
hoses so
the toolbar
raises when
the tractor
remote con­trol lever is
moved rear­ward and
lowers when
the lever
is moved
forward.

Remote
hydraulic

5. Connect the toolbar hydraulic
hoses to the tractor remote
couplers. The 1/2” hoses
supply oil to the toolbar lift
cylinders. The 3/8” hoses
supply oil to the wing fold
cylinders.

6. It may be necessary to tie
the hydraulic hoses up to
keep them away from the
hitch area. A tarp strap
around the hoses and
between the two point arms
works well.

WARNING

WARNING: Hydraulic uid escaping under pressure can have

enough force to penetrate the skin. Hydraulic uid may also
infect a minor cut or opening in the skin. If injured by escaping
uid, see doctor at once. Serious infection or reaction can result
if medical treatment is not given immediately. Make sure all
connections are tight and that hoses and lines are in good
condition before applying pressure to the system. Relieve all
pressure before disconnecting the lines or performing other work
on the hydraulic systems.

12

Attaching
electrical
harness

Jack stand

7. Attach 7 pin electrical
harness before road
transport.

8. Lower the jack and pull
ring on drop leg jack
plunger and raise the sand
pad off the ground. Secure
plunger in holes.

I

MPORTANT: Always lower the

jack stand to the ground before
disconnecting the tool bar from the

tractor.

Ring

LEGACY

Operating Instructions

Leveling
Machine

9. Before leveling the machine
the tire pressure should be
checked.

Inate center section lugged

tractor tires to 51 P.S.I. Maximum
Truck tires 95 P.S.I. Maximum

Before beginning operation of
this machine the main frame
must be level.
Place tool bar on level surface.
Use the turnbuckle wrench to
loosen the lower turnbuckle
jam nut. Adjust turnbuckle with
wrench until the main frame is
level front to back. After making
the necessary adjustment,
lock turnbuckle with jam nut.

Jam Nut

Main Frame

CAUTION

Caution: To prevent serious accident or injury do

not remove wing latch cable release mecha­nism. Wing fall may result during road transport.

10. Unlatch primary wing latch
with the cable release located
on the front of the tool bar
before unfolding tool bar.

NOTE: Cable must be free. Do not place

hydraulic hoses, EVA hoses or ties around
the cable.

13

LEGACY

Operating Instructions

Leveling
adjustable
gauge
wheels

NOTE:

Adjust until
tool bar is
level
across the
entire bar

NOTE:

Coulter will
require

nal

working
depth
adjustment

in the eld.

11. Check tire pressure before
adjusting.
Loosen the two 1” x 4” Hex bolts
at the top of the adjust linkage.
Loosen 1” hex nut on inside of
threaded rod. Turn 1” hex nut
on outside clockwise to lower
wing and counter clockwise to
raise wing. Secure both nuts on
threaded rod against cylinder
lug adjust. Tighten
1” x 4” hex cap screws after
wheel adjustment.

Tighten one inch
hex nuts after
wheel adjustment.

Cylinder lug adjust

One Inch hex nut

14

Pin adjust
gauge
wheel

Depth
collars

12. Adjust pin adjust gauge wheel
to level position with the
hydraulic gauge wheel.

13. Install equal lengths
of cylinder depth collars
to the right and left hand
center section wheel lift
cylinders.

NOTE: Unequal depth collar

installation may result in
wheel lift linkage damage.

LEGACY

Operating Instructions

LOCKED POSTION

DEPTH ADJUSTMENT

1. One complete revolution equals 1/2” of
depth increase.

LOCKING DEPTH ADJUSTMENT
LINKAGE

1. Rotate depth control adjuster latch
over handle and lock in place with

(27) (BP3376) 1/4” x 2” wire retaining

pin.

15

LEGACY

Operating Instructions

Nurse tank
hitch

NOTE:

Periodically
check Latch
mechanism to
ensure proper
latching in the
extended
position.

Secondary
wing latch

14. Nurse tank hitch can be
retracted and moved from
side to side for easy hookup.
Hitch will automatically lock
in the extended position.

WARNING

Pinch point

To prevent Injury

Keep hands clear

when extending or

retracting the swing

slide insert

15. Mechanism must swing
freely in order to operate
properly. Installed position
must be squared with frame
to allow maximum freedom
of movement. Keep soil and
debris from area to allow
maximum movement.

Latch in open position
before wing is folded

Cylinder rod
maintenance

NOTE: After seasonal storage,

check wing latch for freedom of
movement.

16. All exposed cylinder rods
should be greased before
seasonal storage to prevent
rusting.
Remove depth collars and
lubricate exposed cylinder
rods.

16

LEGACY

Operating Instructions

Lug Nut
Torque

Lubrication

17. Lug nut Torque

1. Check every hour rst four

hours.

2. Check every four hours to

rst twenty hours.

3. Check once every fty hours

thereafter.

Zerks

18. Lubrication

• Grease all zerks daily

• Grease coulters daily

Lift Wheel Pivot Zerk
(Torque 150-180 ft. lbs.)

Zerks

Wing Hinges

Zerk

Under

Hitch

Zerks On Wing Gauge
Wheel Pivot
(Torque 100 ft./lbs.)

17

LEGACY

Lubrication

Operating Instructions

Zerks On Linkage

And Hinge

Zerks On Wing Gauge
Wheel Pivot
(Torque 100 ft./lbs.)

Zerks On Linkage

And Hinge

Zerks On Linkage

Coulter
pivot shaft
lubrication

Coulter
hub
lubrication

Emergency
water tank
operation
and
maintenance

And Hinge

19. Grease all coulter arm pivots.

20. The plug on the coulter hub
can be removed. A zerk can
be installed. Hub and spindle
assembly should be greased
twice seasonally.

21. emergency water tank/toolbox.
Change water daily to provide

fresh clean water to ush

exposed skin or eyes.
Drain water daily in cold
temperatures to prevent
freezing and bursting tank.

18

LEGACY

Anhydrous Ammonia Operating Instructions

Attend Anhydrous Ammonia Safety Training Class Provided By Your
Dealer Before Operating this equipment .

Operator protection

Because of the hazards associated
with handling Anhydrous Ammonia,
operators must use proper protective
equipment. Minimum equipment includes

tight-tting chemical-proof goggles,

long cuff rubber gloves, heavy-duty
long sleeved shirt. In case of exposure,

have a minimum of 5 gal`s of ushing

water available at all times.

Checking System

With personal protective equipment in
place, visually inspect the tool bar and system components for integrity, includes
hoses that may be subject to inadvertent contact with structural surfaces resulting in
premature exterior hose deterioration.

Tank Connection

Body Guard

NOTE: A light application

of oil maybe applied to the
break away coupler mating.

Hooking Up Nurse Tank

With personal protective equipment in place, hitch the nurse tank to the tool bar using

a keyed hitch pin. Afx wagon tongue safety chains securely to Nurse tank chain loops

provided.

Break Away

Carefully hand tighten the nurse tank supply hose connection. Position hose to allow
unobstructed movement in case of Nurse Tank break away. Do not allow supply hose
to contact surfaces that may cause abrasion or wear including sharp corners, soil or
roads.

With personal protective equipment in place, conrm the functional operation of the

break away coupler on a daily basis. First bleed pressure off of tank supply hose and
1-1/4” quick coupler using the bleed valves provided.
Sharply pull on the tank supply hose. The coupler mechanism should release under
these forces. Visually inspect coupler for corrosion, foreign elements and proper
seating of mating poppets.

DO NOT transport equipment from eld to eld with tank and supply line valves open.
When immediately ready for eld application, beginning at the tank, and with personal

protective equipment in place, slowly open all supply line valves.

WARNING

WARNING: Position your body away from the bleed

valve exit hole to avoid contact with Anhydrous
Ammonia when bleed valve is opened. Contact with
skin will cause severe chemical burns.

WARNING: Avoid breathing ammonia vapors. Clear

WARNING

all personnel from the area before opening system.
Inhalation of vapors will irritate or damage respiratory
tract and lungs, resulting in injury or death.

Bleed

Valve

19

LEGACY

Anhydrous Ammonia Operating Instructions

Disconnection Of Nurse Tank

1. With personal protective equipment in place, and beginning at the tank, fully
shut off the supply hose valves. If the supply hose is a tank wagon component
(as opposed to a tool bar component) an additional hand operated globe valve
shut off located between the quick coupler and the Heat Exchanger feed line

will signicantly speed up the tank wagon change process.

2. Clear all personnel from area except for the operator. While considering the
direction of the wind to avoid ammonia vapor drift toward the operator or any
other personnel, beginning at the tank, slowly open supply line bleed valves to
release pressure from the hose.

3. Physically grasp, lift and lightly shake the supply hose mid section to insure
total evacuation of ammonia. Once again, be wary of the wind direction.

4. Place the supply hose in a transport storage position, preventing it from
becoming entangled or in contact with sharp edges or abrasive
surfaces.

5. Always park and unhook the nurse tank on a smooth and level surface.
Block the wheels to prevent tank wagon runaway. High winds or uneven
terrain can cause unblocked tank wagons to move out of control.

6. Disconnect tank wagon tongue safety chains, hitch pin key and hitch pin.

CAUTION

CAUTION: Fifth wheel style running gear front axles may inadvertently

rotate in uneven soil conditions when the hitch pin is pulled causing the
tongue to come into contact and potentially injuring the operator.

WARNING

WARNING: Before maintenance is preformed on any part of the NH3

system, be sure the total system is bled off and all liquid is drained. Liquid
ammonia can remain trapped in system cavities, even when the system
has been opened to atmospheric pressure. Always assume that ammonia
remains in the system components and hoses at all times. Always wear
tight-tting chemical-proof goggles, long cuff rubber gloves, heavy-duty
long sleeved shirt and exercise extreme caution.

20

LEGACY

Safety Decals

AP2972

AP2227

AP2974

AP2973

AP2975

21

LEGACY

Coupler Operations

NOTE:

Read
coupler
operation
decal
(AP2974)
for safety
instructions.

Coupler release handle

Female coupler

Male coupler neck

Body Guard III

Feed-line to tank

Coupler bleed valve

Male coupler half

Check valve plunger

Connecting

DANGER

DANGER:

Always wear
protective
gear.

1. Stand on the upwind side. Close all
feed-line valves and inspect all
components for proper condition.

2. Relieve pressure in nurse tank
hose between male coupler (F) and

rst shutoff valve towards nurse tank

by carefully opening coupler bleed
valve (E). The Squibb Flo-Max coupler
is designed to re-couple safely with
pressure on the female coupler half

(B). CAUTION: Leave coupler bleed

valve (E) open for now.

A

B

C

D

Flow
Downstream

E

F

G

22

DANGER:

DANGER

Avoid
breathing
ammonia
vapors.

DANGER

DANGER:

Hazardous
chemical
under
pressure.

Disconnect

3. While holding and pointing the
hose and male coupler (F) downwind
and away from your person, depress
check valve plunger (G) with gloved

nger to ensure proper operation.

Wipe foreign debris from coupler neck

(C) with clean cloth.

4. Make certain BodyGuard III
is installed fully with slot oriented
around check valve plunger (G) to
protect against ammonia spray-back
during coupling.

5. Insert male coupler neck (C) into
female coupler half (B) as far as pos­sible.

Then, while applying insertion
pressure, pull downward on coupler
release handle (A) to complete the
coupling process. Release handle (A)
after engagement of coupler neck (C).

6. Lightly pull on male coupler (F) to
ensure proper engagement.

7. Close bleed valve (E) and others if
open. Open tank and hose valves just
prior to applying ammonia.

TM

(D)

1. After closing all valves, bleed
pressure from male coupler half

(F) by opening coupler bleed valve

(E). Leave bleed valve (E) open.

2. Then, pull down on coupler
release handle (A) and remove
male coupler half (F).

LEGACY

NOTE:

Mount
Safety Tank
after
machine
has been
folded to
avoid
hitting and
collapsing
tank

Emergency Fresh Water Tank Location and Assembly

Location of Nine-gallon safety water
tank/toolbox.
Change water daily to provide fresh

clean water to ush exposed skin

or eyes. Drain water daily in cold
temperatures to prevent freezing
and bursting tank.
In case of exposure to anhydrous
ammonia, open faucet or pull top

end of hose loose to ush exposed

part of body. Remove contaminated
clothes as soon as possible. Seek
medical attention.

NOTE:

Safety Tank
placement
will depend
on row
spacing

BOM ID Qty Item No Description

1 1 PKG00040 PACKAGE, 9 GALLON SAFETY TANK

2 1 AP2137 SAFETY TANK, 9 GALLON
2A 1 AP2137 TANK TANK
2B 1 AP2137 LID TOOLBOX LID
2C 1 CP2577 HOSE BARB, 3/4”MP X 3/4” HOSE BARB, POLY
2D 1 CP2471 ELBOW, 90°, 3/4”MP X 3/4” HOSE BARB POLY
2E 1 AP2329 SPIGOT
2F 1 AP2137 HOSE 3/4” CLEAR HOSE - CP2069 - 24” LENGTH
2G 1 AP2272 2” FILL CAP

3 2 AM2136 BRACKET, TANK MOUNTING, 9 GALLON

4 6 BP3159 WASHER, FLAT, 5/16”, PLATED

5 6 BP3158 WASHER, LOCK, 5/16”, PLATED

6 6 BP3108 HEX CAP SCREW, 5/16”-18 X 1, GRADE 5, PLATED

7 4 BP3002 WASHER, LOCK, 3/8”, PLATED

8 4 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

9 2 BP3351 U-BOLT, 3/8”-16 X 6”W X 7”L

10

1 AP2215 DECAL, BLU-JET, 3” X 8”

23

24

LEGACY

Center Section Area of Bundle 66000126

BOM ID Qty Item No Description

1 1 66000126 LEGACY MAIN FRAME & PRIMARY WINGS

2 2 AAM2437 HOSE RETAINER ASSEMBLY, CLOSED LOOP, 4X6 TUBE

2A 2 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING

2B 4 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

2C 4 BP3002 WASHER, LOCK, 3/8”, PLATED

2D 2 BP3045 U-BOLT, 3/8”-16 X 6”W X 5”L, PLATED

3 13 AAM2438 HOSE RETAINER ASSEMBLY, CLOSED LOOP, 6X6 TUBE

3A 13 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING

3B 26 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

3C 26 BP3002 WASHER, LOCK, 3/8”, PLATED

3D 13 BP3351 U-BOLT, 3/8”-16 X 6”W X 7”L, PLATED

4 1 AAM2639 MANUAL HOLDERW/ 6” X 4” MOUNTING

5 1 AAM2928 STOP ARM, W/ PLUNGER, DEPTH CONTROL

6 1 AAM2930 ADJUSTMENT LINKAGE, LEGACY DEPTH CONTROL

7 1 AAM4768 ASSEMBLY, TURNBUCKLE

8 1 AM2144 HITCH, CLEVIS

9 1 AM2145 BRACKET, HITCH STORAGE, 6” MOUNTING

10 1 AM2197 BRACKET, WRENCH STORAGE

11 1 AM2518 JACK, 9TWDL

12 1 AM2526 CRANK W/ GRIP, 90 LONG

13 3 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING

14 2 AM4415 HOSE RETAINER, OPEN LOOP

15 2 AM4442 HOSE RETAINER, CLOSED LOOP

16 1 AM4511 BRACKET, TURNBUCKLE SUPPORT MOUNTING

17 1 AM4512 TURNBUCKLE SUPPORT

18 2 AM4517 WING LOCK

19 2 AM4524 ROCKER, AT6020

19A 4 BP3072 GREASE ZERK, 1/4”-28

19B 2 BP3560 TENSION BUSHING, 1-1/2” X 1-1/4” X 1” OAL

20 2 AM4528 BRACKET, HOSE HOLDER W/ PRESSURE GAUGE MOUNT

21 2 AM4529 SAFETY LAUNCH TRIP, PRIMARY WING, AT 5000

22 1 AM4563 CYLINDER LUG, BOLT-ON 5” CYLINDER

23 2 AM4564 CYLINDER LUG, SCREW ADJUST

23A 2 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

24 2 AM4566 WING LATCH PIVOT, SECONDARY WING

25 2 AM4567 SPACER PIPE, 6-1/4” OAL

26 4 AM4568 SECONDARY WING LOCK PLATE

27 1 AM4759 TURNBUCKLE WRENCH, 3-1/16”

28 1 AM5155 TONGUE, CAT IV, HD, WEIGHTED

29 1 AM6163 WHEEL LEG, LH, W/ 2-3/4” SPINDLE LOOP

29A 1 BP3213 GREASE ZERK

29B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

29C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

30 1 AM6164 WHEEL LEG, RH, W/ 2-3/4” SPINDLE LOOP

30A 1 BP3213 GREASE ZERK

30B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

LEGACY

Center Section Area of Bundle 66000126

30C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

31 1 AM6172 FRAME, MAIN, AT6020

31A 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

32 4 AM6179 LINKAGE, CYLINDER LUG SUPPORT

33 1 AM6182 LINKAGE, TONGUE CYLINDER ARM

33A 4 BP3072 GREASE ZERK, 1/4”-28

33B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

34 1 AM6183 LINKAGE, TONGUE CYLINDER

35 1 AM6187 WING, PRIMARY, LH, AT6010

35A 2 BP3072 GREASE ZERK, 1/4”-28

36 1 AM6188 WING, PRIMARY, RH, AT6010

37 2 AM6202 CYLINDER LUG, BOLT-ON W/ NOTCH

37A 2 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

38 1 AM6263 BRACKET, PIVOT, DEPTH CONTROL

39 1 AM6264 ARM, VALVE, DEPTH CONTROL

40 1 AM6266 LINKAGE, STOP, DEPTH CONTROL

41 1 AM6271 LATCH, DEPTH CONTROL ADJUSTER

42 1 AM6276 ADJUSTER BRACKET, LEGACY DEPTH CONTROL

43 4 AP2215 DECAL, BLU-JET, 3” X 8”

44 1 AP2222 DECAL, STAND CLEAR OF TONGUE, TONGUE LIGHT

45 1 AP2231 DECAL, FEMA, 2-1/2” X 1-1/2”

46 4 AP2234 DECAL, DANGER STAND CLEAR FALLING WING

47 1 AP2469 DECAL, SAFETY CHAIN

48 1 AP2483 DECAL, DANGER, FALLING FROM EQUIPMENT

49 2 AP2554 DECAL, LEGACY

50 12 AP2711 SNAP RING, 1-1/4 EXTERNAL, HEAVY DUTY

51 1 AP2864 PERFECT HITCH, CAT IV, BLACK

52 2 AP2871 HOSE RETAINER

53 1 AP2914 DECAL, WARNING, HIGH-PRESSURE FLUID

54 1 AP4391 TRANSPORT CHAIN, 60,000#, 5/8’’

55 1 BM3453 SPACER

56 2 BM3465 PIN, 1-1/4” X 7-3/4” OAL, W/ 13/32” HOLE, PLTD

57 4 BM3485 PIN, 1-3/4” X 12-1/8” OAL, W/ 21/32” HOLE, PLTD

58 1 BM3487 PIN, 1 X 7-3/4” OAL, W/ 13/32” HOLE, PLTD

59 2 BM3497 PIN, 1-3/4” X 14-3/4” OAL

60 2 BM3544 PIN, 1-1/4” X 9” USEABLE

61 2 BM3547 PIN, 1-1/4” X 5-3/4” USEABLE

62 2 BM3555 HEX BOLT, 1”-8 X 7-5/16”, FULL THREAD WELDED HEAD

63 2 BM3565 PIN, 2” X 10-1/4” OAL, W/ 21/32” HOLE, PLTD

64 2 BM3610 PIN, 1-3/4” X 6-1/8” USEABLE W/ANTI-ROTATION HEAD

65 2 BM3664 PIN, 1-3/4” X 16-9/16” OAL, W/ 21/32” HOLE

66 12 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

67 12 BP3002 WASHER, LOCK, 3/8”, PLATED

68 9 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED

69 6 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED

70 2 BP3006 HEX CAP SCREW, 3/8”-16 X 1”, GRADE 5, PLATED

25

26

LEGACY

Center Section Area of Bundle 66000126

71 2 BP3015 WASHER, FLAT, 3/8”, PLATED

72 14 BP3019 NUT, HEX, 1”-8, GRADE 2, PLATED

73 6 BP3020 WASHER, LOCK, 1, PLATED

74 2 BP3027 NUT, HEX LOCK, 3/4”-10, GRADE 2, PLATED

75 8 BP3034 NUT, HEX, 3/4”-10, GRD 2, PLATED

76 8 BP3035 WASHER, LOCK, 3/4”, PLATED

77 16 BP3038 NUT, HEX, 5/8”-11, GRADE 2

78 16 BP3039 WASHER, LOCK, 5/8”, PLATED

79 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

80 4 BP3043 WASHER, LOCK, 1/2”, PLATED

81 2 BP3045 U-BOLT, 3/8”-16 X 6”W X 5”L, PLATED

82 2 BP3051 PIN, 1” X 6”, HITCH, PLATED

83 6 BP3072 GREASE ZERK, 1/4”-28

84 3 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED

85 2 BP3099 U-BOLT, 5/8”-11 X 6 X 6, PLATED

86 2 BP3111 HEX CAP SCREW, 5/16”-18 S 2-1/2”, GRADE 5, PLATED

87 3 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED

88 4 BP3118 HEX CAP SCREW, 3/8”-16 X 5”, GRADE 5, PLATED

89 6 BP3135 HEX CAP SCREW, 5/8”-11 X 3-1/2”, GRADE 5, PLATED

90 4 BP3136 HEX CAP SCREW, 5/8”-11 X 4”, GRADE 5, PLATED

91 1 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED

92 1 BP3145 HEX CAP SCREW, 3/4”-10 X 4-1/2”, GRADE 5, ZP

93 2 BP3157 NUT, HEX, 5/16”-18, GRADE 2, PLATED

94 2 BP3158 WASHER, LOCK, 5/16”, PLATED

95 2 BP3179 HEX CAP SCREW, 1/2”-13 X 8”, GRADE 5, PLATED

96 4 BP3200 HEX CAP SCREW, 1”-8 X 3-1/2”, GRADE 5, PLATED

97 8 BP3205 MACHINERY BUSHING, 2-1/2” OD X 1-3/4” ID, 10GA,PLATED

98 2 BP3215 MACHINERY BUSHING, 1-1/2” OD X 1” ID, 14GA, PLATED

99 2 BP3244 NUT, HEX LOCK, 1/2”-13, PLATED

100 12 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLATED

101 2 BP3255 WASHER, FLAT, 3/4”, PLATED STRUCTURAL 10GA

102 6 BP3291 HEX CAP SCREW, 1”-8 X 4”, GRADE 5, PLATED

103 2 BP3330 U-BOLT, 1/2”-13 X 6”W X 5-1/8”L

104 4 BP3347 U-BOLT, 5/8”-11 X 4 X 5-5/8, PLATED

105 4 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

106 2 BP3354 U-BOLT, 5/8”-11 X 4”X 7-3/4”, PLATED

107 10 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

108 1 BP3376 PIN, WIRE RETAINING, 1/4” X 2”, PLATED

109 1 BP3500 PIN, HAIR CLIP, 3/16”

110 2 BP3504 PIN, HAIRCLIP, 1/8”

111 2 BP3511 PIN, COTTER, 3/16” X 1-3/4”

112 2 BP3519 PIN, ROLL, 3/8” X 2-1/2”, PLAIN

113 2 AP4880 PIN, CLEVIS, 3/4” X 3”, ZP

114 1 CP2660 NUT, HEX LOCK, 3/8”-16, NYLOCK

115 1 DP4485

116 1 EM3735 BUSHING

REPHASING CYLINDER, 3-3/4 X 12, PMS-AM-2558

LEGACY

Center Section Area of Bundle 66000126

BOM ID Qty Item No Description

13 3 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING

31 1 AM6172 FRAME, MAIN, AT6020

31A 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

32 4 AM6179 LINKAGE, CYLINDER LUG SUPPORT

33 1 AM6182 LINKAGE, TONGUE CYLINDER ARM

33A 4 BP3072 GREASE ZERK, 1/4”-28

33B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

37 2 AM6202 CYLINDER LUG, BOLT-ON W/ NOTCH

37A 2 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL

56 2 BM3465 PIN, 1-1/4” X 7-3/4” OAL, W/ 13/32” HOLE, PLTD

65 2 BM3664 PIN, 1-3/4” X 16-9/16” OAL, W/ 21/32” HOLE

66 12 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

67 12 BP3002 WASHER, LOCK, 3/8”, PLATED

68 9 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED

69 6 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED

72 14 BP3019 NUT, HEX, 1”-8, GRADE 2, PLATED

73 6 BP3020 WASHER, LOCK, 1, PLATED

84 3 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED

89 6 BP3135 HEX CAP SCREW, 5/8”-11 X 3-1/2”, GRADE 5, PLATED

96 4 BP3200 HEX CAP SCREW, 1”-8 X 3-1/2”, GRADE 5, PLATED

97 8 BP3205 MACHINERY BUSHING, 2-1/2” OD X 1-3/4” ID, 10GA,PLATED

102 6 BP3291 HEX CAP SCREW, 1”-8 X 4”, GRADE 5, PLATED

107 10 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

115 1 DP4485

REPHASING CYLINDER, 3-3/4 X 12, PMS-AM-2558

27

LEGACY

Center Section Area of Bundle 66000126

28

BOM ID Qty Item No Description

2 2 AAM2437 HOSE RETAINER ASSEMBLY, CLOSED LOOP, 4X6 TUBE
2A 2 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING
2B 4 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
2C 4 BP3002 WASHER, LOCK, 3/8”, PLATED
2D 2 BP3045 U-BOLT, 3/8”-16 X 6”W X 5”L, PLATED

4 1 AAM2639 MANUAL HOLDERW/ 6” X 4” MOUNTING

7 1 AAM4768 ASSEMBLY, TURNBUCKLE

8 1 AM2144 HITCH, CLEVIS

9 1 AM2145 BRACKET, HITCH STORAGE, 6” MOUNTING

10 1 AM2197 BRACKET, WRENCH STORAGE
11 1 AM2518 JACK, 9TWDL
12 1 AM2526 CRANK W/ GRIP, 90 LONG
16 1 AM4511 BRACKET, TURNBUCKLE SUPPORT MOUNTING
17 1 AM4512 TURNBUCKLE SUPPORT
20 2 AM4528 BRACKET, HOSE HOLDER W/ PRESSURE GAUGE MOUNT
22 1 AM4563 CYLINDER LUG, BOLT-ON 5” CYLINDER

LEGACY

Center Section Area of Bundle 66000126

27 1 AM4759 TURNBUCKLE WRENCH, 3-1/16”
34 1 AM6183 LINKAGE, TONGUE CYLINDER
44 1 AP2222 DECAL, STAND CLEAR OF TONGUE, TONGUE LIGHT
45 1 AP2231 DECAL, FEMA, 2-1/2” X 1-1/2”
47 1 AP2469 DECAL, SAFETY CHAIN
48 1 AP2483 DECAL, DANGER, FALLING FROM EQUIPMENT
49 2 AP2554 DECAL, LEGACY
50 12 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
51 1 AP2864 PERFECT HITCH, CAT IV, BLACK
52 2 AP2871 HOSE RETAINER
53 1 AP2914 DECAL, WARNING, HIGH-PRESSURE FLUID
54 1 AP4391 TRANSPORT CHAIN, 60,000#, 5/8’’
61 2 BM3547 PIN, 1-1/4” X 5-3/4” USEABLE
63 2 BM3565 PIN, 2” X 10-1/4” OAL, W/ 21/32” HOLE, PLATED
64 2 BM3610 PIN, 1-3/4” X 6-1/8” USEABLE W/ANTI-ROTATION HEAD
66 12 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
67 12 BP3002 WASHER, LOCK, 3/8”, PLATED
68 9 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED
71 2 BP3015 WASHER, FLAT, 3/8”, PLATED
75 8 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
76 8 BP3035 WASHER, LOCK, 3/4”, PLATED
77 16 BP3038 NUT, HEX, 5/8”-11, GRADE 2,
78 16 BP3039 WASHER, LOCK, 5/8”, PLATED
81 2 BP3045 U-BOLT, 3/8”-16 X 6”W X 5”L, PLATED
82 2 BP3051 PIN, 1” X 6”, HITCH, PLATED
84 3 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED
85 2 BP3099 U-BOLT, 5/8”-11 X 6” X 6”, PLATED
88 4 BP3118 HEX CAP SCREW, 3/8”-16 X 5”, GRADE 5, PLATED

90 4 BP3136 HEX CAP SCREW, 5/8”-11 X 4, GRADE 5, PLATED
100 12 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLATED
104 4 BP3347 U-BOLT, 5/8”-11 X 4” X 5-5/8”, PLATED
105 4 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED
107 10 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK
109 1 BP3500 PIN, HAIR CLIP, 3/16”

111 2 BP3511 PIN, COTTER, 3/16” X 1-3/4”
112 2 BP3519 PIN, ROLL, 3/8” X 2-1/2”, PLAIN

29

LEGACY

Center Section Area of Bundle 66000126

Depth Control Assembly

30

LEGACY

Center Section Area of Bundle 66000126

Depth Control Assembly

BOM ID Qty Item No Description

5 1 AAM2928 STOP ARM, W/ PLUNGER, DEPTH CONTROL

6 1 AAM2930 ADJUSTMENT LINKAGE, LEGACY DEPTH CONTROL

38 1 AM6263 BRACKET, PIVOT, DEPTH CONTROL

39 1 AM6264 ARM, VALVE, DEPTH CONTROL

40 1 AM6266 LINKAGE, STOP, DEPTH CONTROL

41 1 AM6271 LATCH, DEPTH CONTROL ADJUSTER

42 1 AM6276 ADJUSTER BRACKET, LEGACY DEPTH CONTROL

55 1 BM3453 SPACER

58 1 BM3487 PIN, 1” X 7-3/4” OAL, W/ 13/32” HOLE, PLATED

74 2 BP3027 NUT, HEX LOCK, 3/4”-10, GRADE 2, PLATED

77 16 BP3038 NUT, HEX, 5/8”-11, GRADE 2

78 16 BP3039 WASHER, LOCK, 5/8”, PLATED

79 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

80 4 BP3043 WASHER, LOCK, 1/2”, PLATED

86 2 BP3111 HEX CAP SCREW, 5/16-18 S 2-1/2, GRADE 5, PLATED

87 3 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED

91 1 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED

92 1 BP3145 HEX CAP SCREW, 3/4-10 X 4-1/2”, GRADE 5, ZP

93 2 BP3157 NUT, HEX, 5/16”-18, GRADE 2, PLATED

94 2 BP3158 WASHER, LOCK, 5/16”, PLATED

98 2 BP3215 MACHINERY BUSHING, 1-1/2” OD X 1” ID, 14GA, PLATED

101 2 BP3255 WASHER, FLAT, 3/4”, PLATED STRUCTURAL 10GA

103 2 BP3330 U-BOLT, 1/2”-13 X 6”W X 5-1/8”L

104 4 BP3347 U-BOLT, 5/8”-11 X 4 X 5-5/8”, PLATED

108 1 BP3376 PIN, WIRE RETAINING, 1/4” X 2”, PLATED

110 2 BP3504 PIN, HAIR CLIP, 1/8”

113 2 AP4880 PIN, CLEVIS, 3/4” X 3”, ZP

114 1 CP2660 NUT, HEX LOCK, 3/8”-16, NYLOCK

31

LEGACY

Primary Wing Right-hand Area of Bundle 66000126

Tractor Side

Tractor Side

AAM2800

AAM2800-1

AM 4597

NOTE:

AAM2800 (With tapered wheel nuts)
and 295/75R22.5 gauge wheel tires.

Do not use AM 4597 with tapered wheel nuts.

32

NOTE:

AAM2800-1 (With ange lock nuts) and

AM4597 hub cap strap are used only with

385/65R22.5 gauge wheel tires.

LEGACY

Primary Wing Right-hand Area of Bundle 66000103

BOM ID Qty Item No Description
3 13 AAM2438 HOSE RETAINER ASSEMBLY, CLOSED LOOP, 6X6 TUBE
3A 13 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING
3B 26 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
3C 26 BP3002 WASHER, LOCK, 3/8”, PLATED
3D 13 BP3351 U-BOLT, 3/8”-16 X 6”W X 7”L, PLATED
13 3 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING
14 2 AM4415 HOSE RETAINER, OPEN LOOP
15 2 AM4442 HOSE RETAINER, CLOSED LOOP
18 2 AM4517 WING LOCK
19 2 AM4524 ROCKER, AT6020
19A 4 BP3072 GREASE ZERK, 1/4”-28
19B 2 BP3560 TENSION BUSHING, 1-1/2” X 1-1/4” X 1” OAL
21 2 AM4529 SAFETY LAUNCH TRIP, PRIMARY WING, AT 5000
23 2 AM4564 CYLINDER LUG, SCREW ADJUST
23A 2 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
24 2 AM4566 WING LATCH PIVOT, SECONDARY WING
25 2 AM4567 SPACER PIPE, 6-1/4” OAL
26 4 AM4568 SECONDARY WING LOCK PLATE
30 1 AM6164 WHEEL LEG, RH, W/ 2-3/4” SPINDLE LOOP
30A 1 BP3213 GREASE ZERK
30B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
30C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL
36 1 AM6188 WING, PRIMARY, RH, AT6010
43 4 AP2215 DECAL, BLU-JET, 3” X 8”
46 4 AP2234 DECAL, DANGER STAND CLEAR FALLING WING
50 12 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
57 4 BM3485 PIN, 1-3/4” X 12-1/8” OAL, W/ 21/32” HOLE, PLATED
59 2 BM3497 PIN, 1-3/4” X 14-3/4” OAL
60 2 BM3544 PIN, 1-1/4” X 9” USEABLE
62 2 BM3555 HEX BOLT, 1”-8 X 7-5/16”, FULL THREAD WELDED HEAD
66 12 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
67 12 BP3002 WASHER, LOCK, 3/8”, PLATED
68 9 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED
69 6 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED
70 2 BP3006 HEX CAP SCREW, 3/8”-16 X 1”, GRADE 5, PLATED
72 14 BP3019 NUT, HEX, 1”-8, GRADE 5, PLATED
77 16 BP3038 NUT, HEX, 5/8”-11, GRADE 2
78 16 BP3039 WASHER, LOCK, 5/8”, PLATED
83 6 BP3072 GREASE ZERK, 1/4”-28
87 3 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
89 6 BP3135 HEX CAP SCREW, 5/8”-11 X 3-1/2”, GRADE 5, PLATED
90 4 BP3136 HEX CAP SCREW, 5/8”-11 X 4, GRADE 5, PLATED
95 2 BP3179 HEX CAP SCREW, 1/2”-13 X 8, GRD 5, PLATED
97 8 BP3205 MACHINERY BUSHING, 2-1/2” OD X 1-3/4” ID, 10GA, PLATED
99 2 BP3244 NUT, HEX LOCK, 1/2”-13, PLATED
100 12 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLATED
102 6 BP3291 HEX CAP SCREW, 1”-8 X 4”, GRADE 5, PLATED
106 2 BP3354 U-BOLT, 5/8”-11 X 4” X 7-3/4”, PLATED
107 10 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

33

LEGACY

Primary Wing Left-hand Area of Bundle 66000126

AAM2800-1

NOTE:

AAM2800 (With tapered wheel nuts)
and 295/75R22.5 gauge wheel tires.

Do not use AM 4597 with tapered wheel nuts.

34

AAM2800

AM 4597

NOTE:

AAM2800-1 (With ange lock nuts) and

AM4597 hub cap strap are used only with

385/65R22.5 gauge wheel tires.

LEGACY

Primary Wing Left-hand Area of Bundle 66000103

BOM ID Qty Item No Description
3 13 AAM2438 HOSE RETAINER ASSEMBLY, CLOSED LOOP, 6X6 TUBE
3A 13 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING
3B 26 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
3C 26 BP3002 WASHER, LOCK, 3/8”, PLATED
3D 13 BP3351 U-BOLT, 3/8”-16 X 6”W X 7”L, PLATED
13 3 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING
14 2 AM4415 HOSE RETAINER, OPEN LOOP
15 2 AM4442 HOSE RETAINER, CLOSED LOOP
18 2 AM4517 WING LOCK
19 2 AM4524 ROCKER, AT6020
19A 4 BP3072 GREASE ZERK, 1/4”-28
19B 2 BP3560 TENSION BUSHING, 1-1/2” X 1-1/4” X 1” OAL
21 2 AM4529 SAFETY LAUNCH TRIP, PRIMARY WING, AT 5000
23 2 AM4564 CYLINDER LUG, SCREW ADJUST
23A 2 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
24 2 AM4566 WING LATCH PIVOT, SECONDARY WING
25 2 AM4567 SPACER PIPE, 6-1/4” OAL
26 4 AM4568 SECONDARY WING LOCK PLATE
29 1 AM6163 WHEEL LEG, LH, W/ 2-3/4” SPINDLE LOOP
29A 1 BP3213 GREASE ZERK
29B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
29C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL
35 1 AM6187 WING, PRIMARY, LH, AT6010
43 4 AP2215 DECAL, BLU-JET, 3” X 8”
46 4 AP2234 DECAL, DANGER STAND CLEAR FALLING WING
50 12 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
57 4 BM3485 PIN, 1-3/4” X 12-1/8” OAL, W/ 21/32” HOLE, PLATED
59 2 BM3497 PIN, 1-3/4” X 14-3/4” OAL
60 2 BM3544 PIN, 1-1/4” X 9” USEABLE
62 2 BM3555 HEX BOLT, 1”-8 X 7-5/16”, FULL THREAD WELDED HEAD
66 12 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
67 12 BP3002 WASHER, LOCK, 3/8”, PLATED
68 9 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED
69 6 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED
70 2 BP3006 HEX CAP SCREW, 3/8”-16 X 1”, GRADE 5, PLATED
72 14 BP3019 NUT, HEX, 1”-8, GRADE 5, PLATED
77 16 BP3038 NUT, HEX, 5/8”-11, GRADE 2
78 16 BP3039 WASHER, LOCK, 5/8”, PLATED
83 6 BP3072 GREASE ZERK, 1/4”-28
87 3 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
89 6 BP3135 HEX CAP SCREW, 5/8”-11 X 3-1/2”, GRADE 5, PLATED
90 4 BP3136 HEX CAP SCREW, 5/8”-11 X 4, GRADE 5, PLATED
95 2 BP3179 HEX CAP SCREW, 1/2”-13 X 8, GRADE 5, PLATED
97 8 BP3205 MACHINERY BUSHING, 2-1/2” OD X 1-3/4” ID, 10GA, PLATED
99 2 BP3244 NUT, HEX LOCK, 1/2”-13, PLATED
100 12 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLATED
102 6 BP3291 HEX CAP SCREW, 1”-8 X 4”, GRADE 5, PLATED
106 2 BP3354 U-BOLT, 5/8”-11 X 4” X 7-3/4”, PLATED
107 10 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

35

LEGACY

Part of Bundle Number:

66000106 SECONDARY WING ECONOMY RIGHT SIDE

Secondary Wing Economy Right Side Bundle 66000106

36

1A

Tractor Side

Tractor Side

LEGACY

Secondary Wing Economy Right Side Bundle 66000106

PART OF 66000106 SECONDARY WING ECONOMY RIGHT SIDE

BOM ID Qty Item No Description

1 1 55000100 single GAUGE WHEEL, PIN ADJUST 6” X 6” MTG, 25-750-6-6

1A 1 AAM2768 WHEEL, 25 X 7.50-15, 4 PLY, 15” X 6” X 6”, WHITE

1AA 2 AP2001 RIM, 15” X 6” X 6”, WHITE
1AB 2 AP2017 TIRE, 25 X 7.50- 5,4 PLY, TERRA RIB
1AC 2 AP2790 VALVE STEM, METAL

1B 1 AM24024 ASSEMBLY, GAUGE WHEEL LEG, PIN ADJUST
1C 1 EM3700 WELDMENT, GAUGE WHEEL LEG, PIN ADJUST
1D 1 AM24025 BRACKET, PIN ADJUST GAUGE WHEEL MOUNTING
1E 4 AP2407 SNAP RING, 1” EXTERNAL, HEAVY DUTY
1F 2 BM3650 PIN, 1 X 5-9/16 USABLE
1G 8 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
1H 8 BP3035 WASHER, LOCK, 3/4”, PLATED

1I 2 BP3051 PIN, 1” X 6”, HITCH, PLATED
1J 4 BP3215 MACHINERY BUSHING, 1-1/2” OD X 1” ID, 14 GAUGE, PLATED
1K 4 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED
1L 2 BP3511 PIN, COTTER, 3/16” X 1-3/4”

2 1 AM4552 WING, SECONDARY, 5’8”, RIGHT-HAND, LEGACY
3 1 AM4565 SECONDARY WING REST
4 1 AM6189 LINKAGE, SECONDARY FOLD, AT6010

4A 2 BP3072 GREASE ZERK, 1/4”-28

5 1 AM6197 WING LINKAGE, 12-1/4”, WITH 1-1/4” HOLE

5A 4 BP3072 GREASE ZERK, 1/4”-28

6 2 AP2215 DECAL, BLU-JET, 3” X 8”
7 2 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
8 1 BM3548 PIN, 1-1/4” X 4-3/4” USABLE, DOUBLE GROOVED, PLATED
9 3 BM3816 PIN, 1-1/4” X 9-13/16” OAL, WITH 13/32 HOLE, PLATED

10 1 BM3817 PIN, 1” X 6-7/8” OAL, WITH 13/32” HOLE, PLATED

11 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
12 4 BP3035 WASHER, LOCK, 3/4”, PLATED
13 2 BP3072 GREASE ZERK, 1/4”-28
14 3 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED
15 1 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
16 4 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED
17 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14 GAUGE
18 4 CP2660 NUT, HEX LOCK, 3/8”-16, NYLOCK
19 1 DP4579 CYLINDER, HYD, 4-1/2” X 20”, SIDE PORTED, B450200BCDDA07B
20 2 DP4581 ADAPTER, 6MJ-10MSAE, 90 DEGREE, 6801-6-10

37

LEGACY

Secondary Wing Economy Left Side Bundle 66000106

PART OF BUNDLE NUMBER:

66000106 SECONDARY WING ECONOMY LEFT SIDE

10

Tractor Side

Tractor Side

38

LEGACY

Secondary Wing Economy Left Side Bundle 66000106

PART OF 66000106 SECONDARY WING ECONOMY LEFT SIDE

BOM ID Qty Item No Description

1 1 55000100 single GAUGE WHEEL, PIN ADJUST 6” X 6” MTG, 25-750-6-6

1A 1 AAM2768 WHEEL, 25 X 7.50-15, 4 PLY, 15” X 6” X 6”, WHITE
1AA 2 AP2001 RIM, 15” X 6” X 6”, WHITE
1AB 2 AP2017 TIRE, 25 X 7.50- 5,4 PLY, TERRA RIB
1AC 2 AP2790 VALVE STEM, METAL

1B 1 AM24024 ASSEMBLY, GAUGE WHEEL LEG, PIN ADJUST

1C 1 EM3700 WELDMENT, GAUGE WHEEL LEG, PIN ADJUST

1D 1 AM24025 BRACKET, PIN ADJUST GAUGE WHEEL MOUNTING

1E 4 AP2407 SNAP RING, 1” EXTERNAL, HEAVY DUTY

1F 2 BM3650 PIN, 1 X 5-9/16 USABLE

1G 8 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

1H 8 BP3035 WASHER, LOCK, 3/4”, PLATED

1I 2 BP3051 PIN, 1” X 6”, HITCH, PLATED

1J 4 BP3215 MACHINERY BUSHING, 1-1/2” OD X 1” ID, 14 GAUGE, PLATED

1K 4 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

1L 2 BP3511 PIN, COTTER, 3/16” X 1-3/4”

2 1 AM4551 WING, SECONDARY, 5’8”, LEFT-HAND, LEGACY
3 1 AM4565 SECONDARY WING REST
4 1 AM6189 LINKAGE, SECONDARY FOLD, AT6010

4A 2 BP3072 GREASE ZERK, 1/4”-28

5 1 AM6197 WING LINKAGE, 12-1/4”, WITH 1-1/4” HOLE

5A 4 BP3072 GREASE ZERK, 1/4”-28

6 2 AP2215 DECAL, BLU-JET, 3” X 8”
7 2 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
8 1 BM3548 PIN, 1-1/4” X 4-3/4” USABLE, DOUBLE GROOVED, PLATED

9 3 BM3816 PIN, 1-1/4” X 9-13/16” OAL, WITH 13/32 HOLE, PLATED
10 1 BM3817 PIN, 1” X 6-7/8” OAL, WITH 13/32” HOLE, PLATED
11 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
12 4 BP3035 WASHER, LOCK, 3/4”, PLATED
13 2 BP3072 GREASE ZERK, 1/4”-28
14 3 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED
15 1 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
16 4 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED
17 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14 GAUGE
18 4 CP2660 NUT, HEX LOCK, 3/8”-16, NYLOCK
19 1 DP4579 CYLINDER, HYD, 4-1/2” X 20”, SIDE PORTED, B450200BCDDA07B
20 2 DP4581 ADAPTER, 6MJ-10MSAE, 90 DEGREE, 6801-6-10

39

LEGACY

Secondary Wing, 3’-2” Right Side Bundle 66000128

BUNDLE NUMBER:
66000128 SECONDARY WING 3’-2” RIGHT SIDE

Tractor Side

40

BUNDLE: 66000128 LEGACY, SECONDARY WINGS, 3’-2” RIGHT SIDE

BOM ID Qty Item No Description

1 1 AM4565 SECONDARY WING REST
2 1 AM6189 LINKAGE, SECONDARY FOLD, AT6010

2A 1 BP3072 GREASE ZERK, 1/4”-28

3 1 AM6197 WING LINKAGE, 12-1/4”, WITH1-1/4” HOLE

3A 2 BP3072 GREASE ZERK, 1/4”-28

4 1 AM6225 WING, SECONDARY, 3’2”, LEGACY
5 1 AP2215 DECAL, BLU-JET, 3” X 8”
6 2 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
7 1 BM3548 PIN, 1-1/4” X 4-3/4” USABLE, DOUBLE GROOVED, PLATED
8 3 BM3816 PIN, 1-1/4” X 9-13/16” OAL, WITH 13/32” HOLE, PLATED
9 1 BM3817 PIN, 1” X 6-7/8” OAL, WITH 13/32” HOLE, PLATED

10 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

11 4 BP3035 WASHER, LOCK, 3/4”, PLATED
12 2 BP3072 GREASE ZERK, 1/4”-28
13 3 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED
14 1 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
15 4 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED
16 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14 GAUGE
17 4 CP2660 NUT, HEX LOCK, 3/8”-16, NYLOCK
18 1 DP4579 CYLINDER, HYD, 4-1/2” X 20”, SIDE PORTED, B450200BCDDA07B
19 2 DP4581 ADAPTER, 6MJ-10MSAE, 90 DEGREE, 6801-6-10

LEGACY

Secondary Wing, 3’-2” Left Side Bundle 66000128

Bundle Number:
66000128 SECONDARY WING 3’-2” LEFT SIDE

Tractor Side

BUNDLE: 66000128 LEGACY, SECONDARY WINGS, 3’-2” LEFT SIDE

BOM ID Qty Item No Description

1 1 AM4565 SECONDARY WING REST
2 1 AM6189 LINKAGE, SECONDARY FOLD, AT6010

2A 1 BP3072 GREASE ZERK, 1/4”-28

3 1 AM6197 WING LINKAGE, 12-1/4”, WITH1-1/4” HOLE

3A 2 BP3072 GREASE ZERK, 1/4”-28

4 1 AM6225 WING, SECONDARY, 3’2”, LEGACY
5 1 AP2215 DECAL, BLU-JET, 3” X 8”
6 2 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
7 1 BM3548 PIN, 1-1/4” X 4-3/4” USABLE, DOUBLE GROOVED, PLATED
8 3 BM3816 PIN, 1-1/4” X 9-13/16” OAL, WITH 13/32” HOLE, PLATED

9 1 BM3817 PIN, 1” X 6-7/8” OAL, WITH 13/32” HOLE, PLATED
10 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
11 4 BP3035 WASHER, LOCK, 3/4”, PLATED
12 2 BP3072 GREASE ZERK, 1/4”-28
13 3 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED
14 1 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
15 4 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED
16 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14 GAUGE
17 4 CP2660 NUT, HEX LOCK, 3/8”-16, NYLOCK
18 1 DP4579 CYLINDER, HYD, 4-1/2” X 20”, SIDE PORTED, B450200BCDDA07B
19 2 DP4581 ADAPTER, 6MJ-10MSAE, 90 DEGREE, 6801-6-10

41

LEGACY

Bundle: 66000127 Legacy Dual Wheel Lift 385/65R22.5 Tires

Valve Stems to the Inside

Valve Stems to the Inside

BUNDLE: 66000127 LEGACY DUAL WHEEL LIFT, 385/65R22.5 TIRES

BOM ID Qty Item No Description

1 4 AAM2924 WHEEL, 385/65 R22.5, 22.5 X 11.75 X 8, GRAY
1A 4 AP2790 VALVE STEM, METAL
1B 4 AP3215
1C 4 AP2888 TIRE, 385/65 R22.5, RECAP IMPLEMENT TREAD

2 4 AAM2800-1 ASSEMBLY, HUB & SPINDLE, 608 HUB, 2-3/4 X 16 SPINDLE, WITH FLANGE LOCK NUT

3 1 AM6173 WHEEL LEG, LEFT-HAND, AT6010, DUALS WITH PIVOT
3A 1 BP3072 GREASE ZERK, 1/4”-28
3B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
3C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

4 1 AM6174 WHEEL LEG, RIGHT-HAND, AT6010, DUALS WITH PIVOT
4A 1 BP3072 GREASE ZERK, 1/4”-28
4B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
4C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

5 2 AM6198 DUALS, ROCKER, WITH SPINDLE LOOPS FOR 2-3/4” SPINDLE
5A 2 BP3072 GREASE ZERK, 1/4”-28
5B 12 EM3301 ASSEMBLY, SET SCREW & JAM NUT, 5/8”-11

6 2 BM3640 PIN, 2” X 12-5/8” OAL

7 2 BP3136 HEX CAP SCREW, 5/8”-11 X 4, GRADE 5, PLATED

8 2 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

9 6 BP3599 MACHINERY BUSHING, 3” OD X 2” ID X 10 GAUGE

RIM, 22.5 X 11.75 X 8, GRAY, 1-1/8” OFFSET

42

Bundle: 66000124 AT6020 Dual Wheel Lift 295/75R22.5 Tires

LEGACY

Valve Stems to the Outside

Valve Stems to the Outside

BUNDLE: 66000124 LEGACY DUAL WHEEL LIFT, 295/75R22.5 TIRES

BOM ID Qty Item No Description

1 4 AAM2923 WHEEL, 295/75R22.5, 22.5 X 8.25 X 8, GRAY, RECAP
1A 4 AP3216 RIM, 22.5 X 8.25 X 8, -1-1/2” OFFSET, GRAY
1B 4 AP2895 TIRE, 295/75R22.5, RIBBED IMPLEMENT, RECAP

2 4 AAM2800 ASSEMBLY, HUB & SPINDLE, 608 HUB, 2-3/4 X 16 SPINDLE

3 1 AM6173 WHEEL LEG, LEFT-HAND, AT6010, DUALS WITH PIVOT
3A 1 BP3072 GREASE ZERK, 1/4”-28
3B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
3C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

4 1 AM6174 WHEEL LEG, RIGHT-HAND, AT6010, DUALS WITH PIVOT
4A 1 BP3072 GREASE ZERK, 1/4”-28
4B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
4C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

5 2 AM6198 DUALS, ROCKER, WITH SPINDLE LOOPS FOR 2-3/4” SPINDLE
5A 2 BP3072 GREASE ZERK, 1/4”-28
5B 12 EM3301 ASSEMBLY, SET SCREW & JAM NUT, 5/8”-11

6 2 BM3640 PIN, 2” X 12-5/8” OAL

7 2 BP3136 HEX CAP SCREW, 5/8”-11 X 4, GRADE 5, PLATED

8 2 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

9 6 BP3599 MACHINERY BUSHING, 3 OD X 2 ID X 10 GAUGE

43

LEGACY

Bundle Number:
66000104 (LEGACY SINGLE WHEEL)

Single Wheel Lift Parts Bundle 66000104

NOTE:

Valve stem on each wheel is positioned
to the inside on 30”, 15” and 20”.

44

LEGACY

PART OF 66000104 (LEGACY SINGLE WHEEL LIFT)

BOM ID Qty Item No Description

Single Wheel Lift Parts Bundle 66000104

1 2 AAM2788-1 ASSEMBLY, HUB AND SPINDLE, 758 HUB, 3 X 16 WITH LOCK

2 1 AM6226 WHEEL LEG, SINGLE WHEEL, LEFT-HAND
2A 1 BP3213 GREASE ZERK
2B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
2C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

3 1 AM6227 WHEEL LEG, SINGLE WHEEL, RIGHT-HAND
3A 1 BP3213 GREASE ZERK
3B 1 BP3516 TENSION BUSHING, 1-1/4” X 1” X 1” OAL
3C 2 BP3538 TENSION BUSHING, 2” X 1-3/4” X 1-1/2” OAL

4 1 AAM2925 WHEEL, 385/85R34 MPT, 141G, 34 X 13 X 8, LEFT-HAND ASSEMBLY
4A 1 AP3217 RIM, 34 X 13 X 8, GRAY
4B 1 AP2790 VALVE STEM, METAL
4C 1 AP3134 TIRE, 385/85R34 MPT 141G, TRACTION GRIP

5 1 AAM2926 WHEEL, 385/85R34 MPT, 141G, 34 X 13 X 8, RIGHT-HAND ASSEMBLY
5A 1 AP3217 RIM, 34 X 13 X 8, WHITE
5B 1 AP2790 VALVE STEM, METAL
5C 1 AP3134 TIRE, 385/85R34 MPT 141G, TRACTION GRIP

LEGACY SD 42 ft.

45

LEGACY

Secondary Wing Stop and Straight Extension

Part of Bundle Number:
66000106 (SECONDARY WINGS)

A

BOM ID Qty Item No Description

A 1 AM4551 WING, SECONDARY, 5’8”, LEFT-HAND, LEGACY
B 1 AM4565 SECONDARY WING REST
C 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
D 4 BP3035 WASHER, LOCK, 3/4”, PLATED
E 4 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED
F 1 AM4552 WING, SECONDARY, 5’8”, RIGHT-HAND, LEGACY

Part of Bundle Number:
66000128 (SECONDARY WINGS)

B

D

C

E

F

BOM ID Qty Item No Description

A 1 AM6225 WING, SECONDARY, 3’2”, LEGACY
B 1 AM4565 SECONDARY WING REST
C 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATE
D 4 BP3035 WASHER, LOCK, 3/4”, PLATED

E 4 BP3139 HEX CAP SCREW, 3/4”-10 X 2”, GRADE 5, PLATED

F 1 AM6225 WING, SECONDARY, 3’2”, LEGACY

1A

55000106 KIT EXTENSION, 28” STRAIGHT, 19 ROW 30”

BOM ID Qty Item No Description

1 1 55000106 single KIT, EXTENSION, AT6010 28” STRAIGHT, 19 ROW 30”
1A 1 AM4544 BRACKET, EXTENSION, 28”, 6” MOUNTING
1B 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
1C 4 BP3035 WASHER, LOCK, 3/4”, PLATED
1D 4 BP3141 HEX CAP SCREW, 3/4”-10 X 3”, GRADE 5, PLATED

46

LEGACY

Bundle: 66000125 Secondary Wing Extension To 50 Ft.

BUNDLE: 66000125 SECONDARY WING EXTENSION TO 50 FT.

BOM ID Qty Item No Description

1 2 AM4547 BRACKET, SPACER, 13-1/2” OAL
2 2 AM6189 LINKAGE, SECONDARY FOLD, AT6010

2A 2 BP3072 GREASE ZERK, 1/4”-28

3 2 AM6197 WING LINKAGE, 12-1/4”, W/ 1-1/4” HOLE

3A 4 BP3072 GREASE ZERK, 1/4”-28

4 2 AM6203 BRACKET, SPACER, 8” OAL
5 2 AM6204 BRACKET, ANGLED STAGGER
6 4 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
7 2 BM3548 PIN, 1-1/4 X 4-3/4 USABLE, DOUBLE GROOVED, PLATED
8 2 BM3816 PIN, 1-1/4” X 9-13/16” OAL, WITH 13/32” HOLE, PLATED
9 2 BM3817 PIN, 1” X 6-7/8” OAL, WITH 13/32” HOLE, PLATED

10 32 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

11 32 BP3035 WASHER, LOCK, 3/4”, PLATED

12 2 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED
13 2 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
14 8 BP3141 HEX CAP SCREW, 3/4”-10 X 3”, GRADE 5, PLATED
15 4 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14 GAUGE
16 4 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED
17 8 BP3352 U-BOLT, 3/4”-10 X 6”W X 5-11/16”L, PLATED
18 4 CP2660 NUT, HEX LOCK, 3/8”-16, NYLOCK
19 2 DP4379 TEE, RUN, 6FJX-6MJ-6MJ, STL, 6602-6
20 2 DP4550 TEE, BRANCH, 6FJX-6MJ-6MJ, 6600-6
21 2 DP4579 CYLINDER, HYDRAULIC, 4-1/2” X 20”, SIDE PORTED, B450200BCDDA07B
22 4 DP4580 ADAPTER, 6MJ-10MSAE, 6400-6-10

47

LEGACY

Gauge Wheel With Pin Adjust & 25 x 7.50 x 15 Tire & Rim

Part of Bundle Number: 66000106
BUNDLE NUMBER 55000100 (PIN ADJUST GAUGE WHEEL)

Tractor side of tool bar

55000100 GAUGE WHEEL, PIN ADJUST 6” X 6” MOUNTING, 25-750-6-6 1 PAIR

BOM ID Qty Item No Description

1 2 AAM2768 WHEEL, 25 X 7.50-15, 4 PLY, 15 X 6 X 6, WHITE
1A 1 AP2001 RIM, 15 X 6 X 6, WHITE
1B 1 AP2017 TIRE, 25 X 7.50- 5,4 PLY, TERRA RIB
1C 1 AP2790 VALVE STEM, METAL

2 2 AM24024 ASSEMBLY, GAUGE WHEEL LEG, PIN ADJUST

3 2 AM24025 BRACKET, PIN ADJUST GAUGE WHEEL MOUNTING

4 4 AP2407 SNAP RING, 1” EXTERNAL, HEAVY DUTY

5 2 BM3650 PIN, 1” X 5-9/16” USABLE

6 8 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

7 8 BP3035 WASHER, LOCK, 3/4”, PLATED

8 2 BP3051 PIN, 1” X 6”, HITCH, PLATED

9 4 BP3215 MACHINERY BUSHING, 1-1/2” OD X 1” ID, 14 GAUGE, PLATED
10 4 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED
11 2 BP3511 PIN, COTTER, 3/16” X 1-3/4”

48

LEGACY

Legacy

AP2554 8-09

Legacy

AP2554 8-09

Decal Placement

1

Install on
bottom side

1

4

Install on
bottom side

1

8

c

OMMeRcIaL cLaSS aPPLIcaTOR

TM

4

6

7

1

2

Decal, Stand Clear of Tongue,
Tongue light

5

3

1

8

c

OMMeRcIaL cLaSS aPPLIcaTOR

TM

Install on
bottom side

1. 8 AP 2215 Decal, BLU-JET, 3” x 8”

2. 1 AP 2222 Decal, Stand Clear of Tongue, Tongue light

3. 1 AP 2231 Decal, FEMA, 2-1/2” x 1-1/2”

4. 4 AP 2234 Decal, Danger stand clear falling wing

5. 1 AP 2469 Decal, Safety Chain

6. 1 AP 2483 Decal, Danger, falling from equipment

7. 1 AP 2914 Decal, Warning, high pressure uid

8. 2 AP 2554 Decal, LEGACY 4.75” x 20.75”

1

4

1

4

Install on
bottom side

1

49

LEGACY

Legacy 38’ and 42’, Toolbars,

Legacy 38’

Legacy 42’

50

Legacy SD 42’

LEGACY

Legacy 47’ and 52’ Toolbars,

Legacy 47’

Legacy 52’

51

LEGACY

Legacy Hydraulic Package

PKG00205 Base, Up to 48’

52

Tractor side

BOM ID Qty Item No Description
1 1 PKG00205 PACKAGE, HYD, LEGACY BASE, UPTO 45’
2 2 AM2090 BRACKET, DEPTH COLLAR & LOCKUP STORAGE
3 1 AM6159 BRACKET, MOUNTING, FLOW DIVIDER VALVE
4 2 AM6280
5 2 BM3520 CLIP PIN, TRANSPORT LOCK
6 4 BM3559 PIN, CLEVIS, 1 X 3 USEABLE, W/ ANTI-ROTATION
7 6 BP3001 NUT, HEX, 3/8”-16, GRD 2, PLTD
8 8 BP3002 WASHER, LOCK, 3/8”, PLTD
9 2 BP3006 HEX CAP SCREW, 3/8”-16 X 1”, GRD 5, PLTD
10 4 BP3028 WASHER, FLAT, 1”, PLTD, STD
11 3 BP3351 U-BOLT, 3/8”-16 X 6W X 7L, PLTD
12 4 BP3511 PIN, COTTER, 3/16 X 1-3/4
13 1 DP4004 TEE, 6MJ-6MJ-6MJ
14 24 DP4086 CABLE TIE 11-3/8” STD
15 13 DP4143 ADAPTER, 10MJIC-8MSAE, 90*
16 1 DP4377 VALVE, REMOTE STROKE CONTROL, PM-SC-10
17 1 DP4379 TEE, RUN, 6FJX-6MJ-6MJ, STL, 6602-6
18 4 DP4383 COUPLER, PIONEER, 8MQBA-8FSAE
19 5 DP4392 ADAPTER, 8MSAE-10MJIC, STRAIGHT, 6400-10-8
20 2 DP4398-1 5” X 36” HYD CYLINDER, W/ 2-3/4” SPACER
21 4 DP4399 REDUCER, 10MSAE-8FSAE, 6410-10-8
22 1 DP4485 REPHASING CYLINDER, 3-3/4 X 12, PMS-AM-2558
23 2 DP4486 REPHASING CYLINDER, 4 X 12, PMS-AM-2552A
24 2 DP4487 REPHASING CYLINDER, 4-1/2 X 12 PMS-AM-2546
25 4 DP4550 TEE, BRANCH, 6FJX-6MJ-6MJ, 6600-6
26 4 DP4551 ADAPTER, 6MJ-8MSAE, W/ RESTRICTOR, 6400R-6-8-093
27 1 DP4590 FLOW DIVIDER WITH HOLDING VALVES
28 1 DP6564 PLUG, 8MSAE, HEX, 6408-8

TRANSPORT CYLINDER LOCK, 1-3/4” & 2” CYL ROD, 12”

LEGACY

Legacy Hydraulic Package

PKG00205 Base, Up to 48’

Tractor side

Tractor side

53

LEGACY

Legacy Hydraulic Package

PKG00205 Base, Up to 48’

Left-hand from

the rear

Tractor side

Right-hand

from the rear

54

Tractor side

LEGACY

Legacy 38’, 42’, 47’ Hydraulics

BOM ID Qty Item No Description

A 1 DP4496 HOSE, HYD, 1/2 X 114, 10FJX-10FJX
B 1 DP5001 HOSE, HYD, 1/2 X 168, 10FJX-10FJX
C 1 DP5230 HOSE, HYD, 1/2 X 42, 10FJX-10FJX
D 2 DP5184 HOSE, HYD, 1/2 X 192, 10FJX-10FJX
E 1 DP5186 HOSE, HYD, 1/2 X 132, 10FJX-10FJX
F 2 DP5200 HOSE, HYD, 3/8 X 202, 6FJX-8MSAE
G 2 DP5235 HOSE, HYD, 1/2 X 252, 10FJX-10FJX
H 1 DP5275 HOSE, HYD, 1/2 X 204, 10FJX-8MSAE

I 1 DP5308 HOSE, HYD, 3/8 X 32, 6FJX-6FJX

J 1 DP5309 HOSE, HYD, 3/8 X 43, 6FJX-6FJX

K 1 DP5310 HOSE, HYD, 3/8 X 77, 6FJX-6FJX

L 2 DP5314 HOSE, HYD, 3/8 X 152, 6FJX-6FJX
M 2 DP5315 HOSE, HYD, 3/8 X 168, 6FJX-6FJX
N 1 DP5350 HOSE, HYD, 1/2 X 228, 10FJX-8MSAE

55

LEGACY

Legacy 38’, 42’, 47’ Hydraulics

56

LEGACY

Legacy 38’, 42’, 47’ Hydraulics

Legacy 42’

Legacy 42’

57

LEGACY

Legacy Hydraulics 52’

DP4579 4-1/2” x 20”

Part Of Bundle 66000125

58

DP4579 4-1/2” x 20”

Part Of Bundle 66000125

DP4579 4-1/2” x 20”

Part Of Bundle 66000106

LEGACY

Legacy Hydraulics 52’

Includes: PKG000205 Package, Hydraulic, AT6020 Base, Up To 45’ Economy
Hydraulics from 66000106, AT6020, Secondary Wings Economy
Hydraulics from 66000125, AT6020, Secondary Wing Extensions To 50’

BOM ID Qty Item No Description

1 1 PKG00205 PACKAGE, HYD, LEGACY BASE, UPTO 45’
2 2 AM2090 BRACKET, DEPTH COLLAR & LOCKUP STORAGE
3 1 AM6159 BRACKET, MOUNTING, FLOW DIVIDER VALVE
4 2 AM6280 TRANSPORT CYLINDER LOCK, 1-3/4” & 2” CYL ROD, 12”
5 2 BM3520 CLIP PIN, TRANSPORT LOCK
6 4 BM3559 PIN, CLEVIS, 1 X 3 USEABLE, W/ ANTI-ROTATION
7 6 BP3001 NUT, HEX, 3/8”-16, GRD 2, PLTD
8 8 BP3002 WASHER, LOCK, 3/8”, PLTD

9 2 BP3006 HEX CAP SCREW, 3/8”-16 X 1”, GRD 5, PLTD
10 4 BP3028 WASHER, FLAT, 1”, PLTD, STD
11 3 BP3351 U-BOLT, 3/8”-16 X 6W X 7L, PLTD
12 4 BP3511 PIN, COTTER, 3/16 X 1-3/4
13 1 DP4004 TEE, 6MJ-6MJ-6MJ
14 24 DP4086 CABLE TIE 11-3/8” STD
15 13 DP4143 ADAPTER, 10MJIC-8MSAE, 90*
16 1 DP4377 VALVE, REMOTE STROKE CONTROL, PM-SC-10
17 1 DP4379 TEE, RUN, 6FJX-6MJ-6MJ, STL, 6602-6
18 4 DP4383 COUPLER, PIONEER, 8MQBA-8FSAE
19 5 DP4392 ADAPTER, 8MSAE-10MJIC, STRAIGHT, 6400-10-8
20 2 DP4398-1 5” X 36” HYD CYLINDER, W/ 2-3/4” SPACER
21 4 DP4399 REDUCER, 10MSAE-8FSAE, 6410-10-8
22 1 DP4485 REPHASING CYLINDER, 3-3/4 X 12, PMS-AM-2558
23 2 DP4486 REPHASING CYLINDER, 4 X 12, PMS-AM-2552A
24 2 DP4487 REPHASING CYLINDER, 4-1/2 X 12, AM2546
25 4 DP4550 TEE, BRANCH, 6FJX-6MJ-6MJ, 6600-6
26 4 DP4551 ADAPTER, 6MJ-8MSAE, W/ RESTRICTOR, 6400R-6-8-093
27 1 DP4590 FLOW DIVIDER WITH HOLDING VALVES
28 1 DP6564 PLUG, 8MSAE, HEX, 6408-8

AA 2 DP4579 CYLINDER, HYDRAULIC, 4-1/2” X 20”, SIDE PORTED, B450200BCDDA07B

AB 4 DP4581 ADAPTER, 6MJ-10MSAE, 90 DEGREE, 6801-6-10

BA 2 DP4379 TEE, RUN, 6FJX-6MJ-6MJ, STL, 6602-6

BB 2 DP4550 TEE, BRANCH, 6FJX-6MJ-6MJ, 6600-6

BC 2 DP4579 CYLINDER, HYDRAULIC, 4-1/2” X 20”, SIDE PORTED, B450200BCDDA07B

BD 3 DP4580 ADAPTER, 6MJ-10MSAE, 6400-6-10

59

LEGACY

Legacy 52’ Hydraulics

60

Tractor sideTractor side

Legacy 52’ Hydraulic Hoses

LEGACY

Includes: PKG000205 Package, Hydraulic, AT6020 Base, Up To 45’ Economy
Hydraulics from 66000106, AT6020, Secondary Wings Economy
Hydraulics from 66000125, AT6020, Secondary Wing Extensions To 50’

Right-hand

from the rear

BOM ID Qty Item No Description

A 1 DP4496 HOSE, HYDRAULIC, 1/2” X 114”, 10FJX-10FJX
B 1 DP5001 HOSE, HYDRAULIC, 1/2” X 168”, 10FJX-10FJX
C 4 DP5055 HOSE, HYDRAULIC, 1/4” X 66”, 6FJX-6FJX
D 2 DP5184 HOSE, HYDRAULIC, 1/2” X 192”, 10FJX-10FJX

E 1 DP5186 HOSE, HYDRAULIC, 1/2” X 132”, 10FJX-10FJX

F 2 DP5200 HOSE, HYDRAULIC, 3/8” X 202”, 6FJX-8MSAE
G 2 DP5235 HOSE, HYDRAULIC, 1/2” X 252”, 10FJX-10FJX
H 2 DP5275 HOSE, HYDRAULIC, 1/2” X 204”, 10FJX-8MSAE

I 1 DP5308 HOSE, HYDRAULIC, 3/8” X 32”, 6FJX-6FJX

J 1 DP5309 HOSE, HYDRAULIC, 3/8” X 43”, 6FJX-6FJX
K 1 DP5310 HOSE, HYDRAULIC, 3/8” X 77”, 6FJX-6FJX

L 2 DP5314 HOSE, HYDRAULIC, 3/8” X 152”, 6FJX-6FJX

M 2 DP5315 HOSE, HYDRAULIC, 3/8” X 168”, 6FJX-6FJX

N 1 DP5230 HOSE, HYDRAULIC, 1/2” X 42”, 10FJX-10FJX
O 1 DP5350 HOSE, HYDRAULIC, 1/2” X 228”, 10FJX-8MSAE

61

LEGACY

Legacy 52’ Hydraulics

62

LEGACY

Legacy 52’ Hydraulics

63

LEGACY

Stagger Brackets Offset 6” x 6” Mounting

BOM ID Qty Item No Description

1 1 AAM2141 BRACKET, OFFSET STAGGER, 22 X 8, 6 X 6,

2 1 AM4510 BRACKET, OFFSET STAGGER, 22 X 8
3 2 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED
4 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
5 4 BP3035 WASHER, LOCK, 3/4”, PLATED

W/ HARDWARE

BOM ID Qty Item No Description

1 1 AAM2123 BRACKET, OFFSET STAGGER, 22 X 20, 6 X 6,

2 1 AM4545 BRACKET, OFFSET STAGGER, 22 X 20
3 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
4 4 BP3035 WASHER, LOCK, 3/4”, PLATED
5 2 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

W/ HARDWARE

BOM ID Qty Item No Description

1 1 AAM2130 BRACKET, EXTENSION, 26”, 6 X 6, W/HARDWARE
2 1 AM4542 BRACKET, EXTENSION, 26”, 6” MTG, W/ ANTI-ROTATION
3 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
4 4 BP3035 WASHER, LOCK, 3/4”, PLATED
5 2 BP3352 U-BOLT, 3/4”-10 X 6”W X 5-11/16”L, PLATED

NOTE: Consult row spacing

diagram for placement of offset
stagger brackets.

64

BOM ID Qty Item No Description
1 1 AAM2128 BRACKET, EXTENSION, 14”, 6 x 6, W/HARDWARE
2 1 AM4543 BRACKET, EXTENSION, 14”, 6” MTG, W/ANTI-ROTATION
3 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
4 4 BP3035 WASHER, LOCK, 3/4”, PLATED
5 2 BP3352 U-BOLT, 3/4”-10 X 6”W X 5-11/16”L, PLATED

LEGACY

Stagger Brackets Offset 6” x 6” Mounting

BOM ID Qty Item No Description
1 1 AAM2122 BRACKET, OFFSET STAGGER, 33 X 20, 6 X 6,

2 1 AM4509 BRACKET, OFFSET STAGGER, 33X20
3 4 BP3034 NUT, HEX, 3/4”-10 GRADE 2, PLATED
4 4 BP3035 WASHER, LOCK, 3/4”, PLATED
5 2 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

W/HARDWARE

NOTE: Consult row spacing

diagram for placement of offset
stagger brackets.

BOM ID Qty Item No Description
1 1 AAM2129 BRACKET, EXTENSION, 20”, 6 x 6, W/HARDWARE
2 1 AM6162 BRACKET, EXTENSION, 20”, 6” MTG, W/ ANTI-ROTATION
3 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED
4 4 BP3035 WASHER, LOCK, 3/4”, PLATED
5 2 BP3352 U-BOLT, 3/4”-10 X 6”W X 5-11/16”L, PLATED

BOM ID Qty Item No Description
1 1 AAM2125 BRACKET, OFFSET STAGGER, 40 X 48 DOUBLE, 6 X 6,

W/HARDWARE
2 1 AM6160 TUBE, 4’, 6” X 6”, CAPPED
3 1 AM6161 BRACKET, EXTENSION, 35”, DOUBLE MTG, 6 X 6
4 16 BP3034 NUT, HEX, 3/4”-10, GRD 2, PLTD
5 16 BP3035 WASHER, LOCK, 3/4”, PLTD
6 8 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLTD

65

LEGACY

Super 1200 Flex Coulter and Shank Parts

AP2707, HUB ASSEMBLY, 4 BOLT

BOM ID Qty Item No Description

1 1 AP2707 HUB ASSEMBLY, 4 BOLT
2 1 AP2703 HUB CAP, 1610

3 1 AP2706-1 HUB W/ CUPS, 4 BOLT, 5” BC, 3.62” PILOT, W/ZERK HOLE
3A 1 AP2075 BEARING CUP, LM 11910
3B 1 AP2524 BEARING CUP, LM 67010

4 1 AP2747 GREASE SEAL, 15235TB

5 1 AP2023 BEARING CONE, LM 67048

6 1 AP2024 BEARING CONE, LM 11949

7 4 AP2702 HEX CAP SCREW, 1/2”-20 X 1”, GRADE 5, PLATED

8 1 BP3072 GREASE ZERK, 1/4”-28

AM2799, ASSEMBLY, COULTER ARM WITH HUB & KNEE CASTING, HD

BOM ID Qty Item No Description

1 1 AM2799 ASSEMBLY, COULTER ARM WITH HUB & KNEE CASTING, HD

2 1 AM2743 CASTING, COULTER KNEE, HD, MACHINED WITH BUSHINGS

2A 2 AP2274 BUSHING, 1-17/32” OD X 1-3/8” ID” X 1” OAL

2B 1 AP2477-1 CASTING, COULTER KNEE, MACHINED

3 1 AM2796 SPRING CAP & GUIDE, HD COULTER

4 1 AM2797 COULTER ARM, HD

4A 1 AP2216 DECAL, BLU-JET, SMALL, 1-1/2” X 4”

5 1 AP2029 PIN, COTTER, 5/32” X 1-1/2”

6 1 AP2704 NUT, SPINDLE, 3/4”-16

7 1 AP2705 WASHER, SPINDLE, 1-1/2” X 13/16” X .134”

8 1 AP2881D SPRING, 2.472” OD X 5.875” OAL, .468 WIRE DIAMETER

9 1 BP3072 GREASE ZERK, 1/4”-28

10 1 BP3404 MACHINERY BUSHING, 2-1/8” OD X 1-3/8” ID X 10 GAUGE, PLATED

11 1 BP3405 SNAP RING, 1-3/8” EXTERNAL, 5160-137

AAM2728 COULTER, SUPER 1200, 16, 1 ROW

BOM ID Qty Item No Description

1 1 AAM2728 COULTER, SUPER 1200, 16, 1R
2 1 AM2735 COULTER SHANK, 16”
3 1 AM2799 ASSEMBLY, COULTER ARM W/ HUB & KNEE CASTING, HD
4 1 BP3162 PIN, ROLL, 3/8” X 2”, PLATED
5 1 BP3205 MACHINERY BUSHING, 2-1/2” OD X 1-3/4” ID, 10GA, PLATED
6 1 BP3519 PIN, ROLL, 3/8” X 2-1/2”, PLAIN
7 1 BP3534 PIN, ROLL, 7/32” X 2-1/2”, PLAIN

66

LEGACY

PKG00234 Nurse Tank Hitch Assembly Parts

BOM ID Qty Item No Description

1 1 PKG00234 NURSE TANK HITCH ASSEMBLY, AT6020
2 1 AAM2931 ASSEMBLY, NURSE TANK HITCH, AUTO-LOK, W/O PIN
3 2 AM6220 BRACKET, HITCH MOUNTING, AT6010 NURSE TANK
4 1 AM6273 BRACKET, NURSE TANK HITCH MOUNTING, LOW
5 1 AM6278 LINKAGE, NURSE TANK HITCH, 12-3/4”
6 4 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
7 1 BM3544 PIN, 1-1/4” X 9” USEABLE
8 1 BM3547 PIN, 1-1/4” X 5-3/4” USEABLE
9 2 BM3632 PIN, CATEGORY IV, UPPER LINK

10 8 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

11 8 BP3035 WASHER, LOCK, 3/4”, PLATED
12 2 BP3135 HEX CAP SCREW, 5/8”-11 X 3-1/2”, GRADE 5, PLATED
13 12 BP3140 HEX CAP SCREW, 3/4”-10 X 2-1/2, GRADE 5, PLATED
14 4 BP3208 U-BOLT, 3/4”-10 X 6”W X 5-11/16”L, PLATED
15 4 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLATED
16 2 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK
17 12 BP3442 NUT, HEX LOCK, 3/4”-10, TOP LOCK, GRADE C, PLATED

67

LEGACY

PKG00247 Nurse Tank Hitch Assembly,

Low Mounting Parts

68

BOM ID Qty Item No Description

1 1 PKG00247 NURSE TANK HITCH ASSEMBLY, AT6, LOW MOUNTING
2 1 AAM2931 ASSEMBLY, NURSE TANK HITCH, AUTO-LOK, W/O PIN
3 2 AM6234 BRACKET, LOW HITCH MOUNTING, AT6020 NURSE TANK
4 1 AM6273 BRACKET, NURSE TANK HITCH MOUNTING, LOW
5 1 AM6278 LINKAGE, NURSE TANK HITCH, 12-3/4”
6 4 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
7 1 BM3544 PIN, 1-1/4” X 9” USEABLE
8 1 BM3547 PIN, 1-1/4” X 5-3/4” USEABLE
9 2 BM3632 PIN, CATEGORY IV, UPPER LINK

10 8 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

11 8 BP3035 WASHER, LOCK, 3/4”, PLATED
12 2 BP3135 HEX CAP SCREW, 5/8”-11 X 3-1/2”, GRADE 5, PLATED
13 12 BP3140 HEX CAP SCREW, 3/4”-10 X 2-1/2”, GRADE 5, PLATED
14 4 BP3208 U-BOLT, 3/4”-10 X 6”W X 5-11/16”L, PLATED
15 4 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLATED
16 2 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK
17 12 BP3442 NUT, HEX LOCK, 3/4”-10, TOP LOCK, GRADE C, PLATED

LEGACY

Auto-Lok Nurse Tank Hitch AAM2931 Parts

BOM ID Qty Item No Description

1 1 AAM2931 ASSEMBLY, NURSE TANK HITCH, AUTO-LOK, W/O PIN
2 1 AM4533 HITCH, SWING SLIDE INSERT, STANDARD
3 1 AM4534 FLIPPER HITCH, STANDARD, NURSE TANK HITCH
4 1 AM4539 SAFETY LATCH
5 1 AM4540 BACKING PLATE, SAFETY CHAIN LOOP, STD NURSE TANK HITCH
6 1 AM6230 BRACKET, SAFETY CHAIN ATTACHMENT

7 1 AM6272 HITCH, NURSE TANK, MAIN FRAME
7A 1 AM4536 INSERT LATCH, NURSE TANK HITCH
7B 2 AP2407 SNAP RING, 1” EXTERNAL, HEAVY DUTY
7C 1 BM3551 PIN, 1” X 15-1/8” USEABLE
7D 2 BP3215 MACHINERY BUSHING, 1-1/2” OD X 1” ID, 14GA, PLATED

8 2 AP2585 DECAL, HITCH CAPACITY, 25000 LB

9 1 AP2711 SNAP RING, 1-1/4” EXTERNAL, HEAVY DUTY
10 1 BM3549 PIN, 1-1/4” X 5-5/16” USEABLE, GROOVED W/ ANTI-ROTATION PIN

11 1 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED
12 1 BP3006 HEX CAP SCREW, 3/8”-16 X 1”, GRADE 5, PLATED
13 1 BP3072 GREASE ZERK, 1/4”-28
14 1 BP3192 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID X 10GA, PLATED
15 2 BP3257 GREASE ZERK, 1/4”-28, 65°
16 1 BP3442 NUT, HEX LOCK, 3/4”-10, TOP LOCK, GRADE C, PLATED
17 1 BP3449 HEX CAP SCREW, 3/4”-10 X 6”, GRADE 8, PLATED

69

LEGACY

Blades

Coulter Blade
Fluted Blade 20”
AP2701

SealPro (Disc Sealer) Blade Options

AM2479
17” Notched Blade

AM2473
18” hoe wheel

AP2728
17” wavy

70

LEGACY

SealPro II (AAM2855) Disc Sealer

1” x 2” Shank Parts

AAM2855 SEALPRO II, 1” X 2” SHANK, 1 ROW

BOM ID Qty Item No Description

1 2 AM2481 ASSEMBLY, SEALER HANGER WITH BLADE MOUNTING

2 1 AM2485 ASSEMBLY, SEALER MOUNTING BRACKET

2A 1 AM2484 BRACKET, SEALER MOUNTING

2B 1 BM3643 PIN, 1-1/4” X 12-1/2” OAL, SEALER SHAFT

2C 2 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED

2D 2 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED

3 1 AM2486 SEALER ARM, LEFT HAND

3A 2 AP3115 BUSHING, SELF-LUBRICATED 1-1/4” X 1-1/4” LONG

4 1 AM2487 SEALER ARM, RIGHT HAND

4A 2 AP3115 BUSHING, SELF-LUBRICATED 1-1/4” X 1-1/4” LONG

5 4 BP3041 HEX CAP SCREW, 1/2”-13 X 2”, GRADE 5, PLATED

6 16 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

7 16 BP3043 WASHER, LOCK, 1/2”, PLATED

8 8 BP3050 WASHER, FLAT, 1/2”, PLATED

9 8 BP3125 HEX CAP SCREW, 1/2”-13 X 1”, GRADE 5, PLATED

10 2 BP3162 PIN, ROLL, 3/8” X 2”, PLATED

11 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14 GAUGE

12 2 BP3313 U-BOLT, 1/2”-13 X 2”W X 2-3/4”L, PLATED

Notched Blade Optional

71

LEGACY

SealPro II (AAM2856) Disc Sealer

1-1/4” Edge Bent Shank

72

AAM2856 SEALPRO II, 1-1/4” EDGE BENT SHANK, 1 ROW

BOM ID Qty Item No Description

1 2 AM2481

2 1 AM2485

2A 1 AM2484

2B 1 BM3643 PIN, 1-1/4” X 12-1/2” OAL, SEALER SHAFT

2C 2 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED

2D 2 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED

3 1 AM2486 SEALER ARM, LEFT HAND

3A 2 AP3115 BUSHING, SELF-LUBRICATED 1-1/4” X 1-1/4” LONG

4 1 AM2487 SEALER ARM, RIGHT HAND

4A 2 AP3115 BUSHING, SELF-LUBRICATED 1-1/4” X 1-1/4” LONG

5 4 BP3041 HEX CAP SCREW, 1/2”-13 X 2”, GRADE 5, PLATED

6 16 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

7 16 BP3043 WASHER, LOCK, 1/2”, PLATED

8 8 BP3050 WASHER, FLAT, 1/2”, PLATED

9 8 BP3125 HEX CAP SCREW, 1/2”-13 X 1”, GRADE 5, PLATED

10 2 BP3162 PIN, ROLL, 3/8” X 2”, PLATED

11 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14 GAUGE

12 2 BP3314 U-BOLT, 1/2”-13 X 1-1/4”W X 3-3/4”L, PLATED

ASSEMBLY,

ASSEMBLY,

BRACKET,

SEALER HANGER WITH BLADE MOUNTING

SEALER MOUNTING BRACKET

SEALER MOUNTING

Notched Blade Optional

LEGACY

SealPro SKF (AAM2893) Disc Sealer

1-1/4” Edgebent Shank

BOM ID Qty Item No Description
1 1 AAM2893 SEALPRO SKF, 1-1/4 EDGEBENT, 1 ROW
2 1 AM2485 ASSEMBLY, SEALER MTG BRACKET
2A 1 AM2484 BRACKET, SEALER MOUNTING
2B 1 BM3643 PIN, 1-1/4” X 12-1/2” OAL, SEALER SHAFT
2C 2 BP3003 NUT, HEX LOCK, 3/8”-16, GRD 2, PLTD
2D 2 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRD 5, PLTD
3 2 AM2745 SEALER HANGER MOUNT, FOR SKF HUB
4 2 AM2747 SPACER, SEALPRO BLADE
5 2 AM2748 WASHER, 1-1/2” OD X 25/32” ID X 1/4”
6 2 AM2749 BOLT, MOUNTING, SEALPRO HUB
7 1 AM2750 SEALER ARM, LH, GREASEABLE, 2 POSITION
7A 1 BP3072 GREASE ZERK, 1/4”-28
8 1 AM2751 SEALER ARM, RH, GREASEABLE, 2 POSITION
8A 1 BP3072 GREASE ZERK, 1/4”-28
9 2 AP2216 DECAL, BLU-JET, SMALL, 1-1/2” X 4”
10 2 AP4581 BEARING UNIT, ADH 7546
11 4 BP3041 HEX CAP SCREW, 1/2”-13 X 2”, GRD 5, PLTD
12 8 BP3042 NUT, HEX, 1/2”-13, GRD 2, PLTD
13 8 BP3043 WASHER, LOCK, 1/2”, PLTD
14 6 BP3050 WASHER, FLAT, 1/2”, PLTD
15 12 BP3150 HEX CAP SCREW, 1/4”-20 X 1”, GRD 5, PLTD
16 2 BP3162 PIN, ROLL, 3/8” X 2”, PLTD
17 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLTD
18 2 BP3314 U-BOLT, 1/2”-13 X 1-1/4W X 3-3/4L, PLTD
19 12 BP3367 NUT, HEX FLANGE, 1/4”-20, SERRATED, GRADE 2, PLATED
20 2 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

73

LEGACY

SealPro SKF (AAM2892) Disc Sealer

1 X 2” Shank

BOM ID Qty Item No Description

1 1 AAM2892 SEALPRO SKF, 1X2 SHANK, 1 ROW

2 1 AM2485 ASSEMBLY, SEALER MOUNTING BRACKET
2A 1 AM2484 BRACKET, SEALER MOUNTING
2B 1 BM3643 PIN, 1-1/4” X 12-1/2” OAL, SEALER SHAFT
2C 2 BP3003 NUT, HEX LOCK, 3/8”-16, GRADE 2, PLATED
2D 2 BP3096 HEX CAP SCREW, 3/8”-16 X 2-1/2”, GRADE 5, PLATED

3 2 AM2745 SEALER HANGER MOUNT, FOR SKF HUB

4 2 AM2747 SPACER, SEALPRO BLADE

5 2 AM2748 WASHER, 1-1/2” OD X 25/32” ID X 1/4”

6 2 AM2749 BOLT, MOUNTING, SEALPRO HUB

7 1 AM2750 SEALER ARM, LH, GREASEABLE, 2 POSITION
7A 1 BP3072 GREASE ZERK, 1/4”-28

8 1 AM2751 SEALER ARM, RH, GREASEABLE, 2 POSITION
8A 1 BP3072 GREASE ZERK, 1/4”-28

9 2 AP2216 DECAL, BLU-JET, SMALL, 1-1/2” X 4”
10 2 AP4581 BEARING UNIT, ADH 7546

11 4 BP3041 HEX CAP SCREW, 1/2”-13 X 2”, GRADE 5, PLATED
12 8 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED
13 8 BP3043 WASHER, LOCK, 1/2”,PLATED
14 6 BP3050 WASHER, FLAT, 1/2”, PLATED
15 12 BP3150 HEX CAP SCREW, 1/4”-20 X 1”, GRADE 5, PLATED
16 2 BP3162 PIN, ROLL, 3/8” X 2”, PLATED
17 2 BP3249 MACHINERY BUSHING, 1-7/8” OD X 1-1/4” ID, 14GA, PLATED
18 2 BP3313 U-BOLT, 1/2”-13 X 2”W X 2-3/4”L, PLATED
19 12 BP3367 NUT, HEX FLANGE, 1/4”-20, SERRATED, GRADE 2, PLATED
20 2 BP3375 NUT, HEX LOCK, 5/8”-11, NYLOCK

74

LEGACY

SealPro II (AAM2857) Assembly,

Optional Sealer II Spring Add-on Kit 1 Row

AAM2857 OPTIONAL SEALPRO II SPRING ADD-ON KIT 1 ROW

BOM ID Qty Item No Description

1 2 AM2488 CLEVIS,

2 2 AM2489 CLEVIS,

3 2 AM2490 TUBE, UPPER SPRING

4 2 AM2491 BUSHING, SPRING COLLAR

5 2 AM2492 TUBE, SPRING GUIDE

6 2 AP2997W SPRING, 1.75” OD X 1.313” ID X 6.00” OAL

7 2 AP3116 TUBE PLUG

8 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

9 4 BP3043 WASHER, LOCK, 1/2”, PLATED

10 8 BP3050 WASHER, FLAT, 1/2”, PLATED

11 4 BP3126 HEX CAP SCREW, 1/2”-13 X 1-1/2”, GRADE 5, PLATED

12 2 BP3129 HEX CAP SCREW, 1/2”-13 X 3”, GRADE 5, PLATED

13 2 BP3130 HEX CAP SCREW, 1/2”-13 X 3-1/2”, GRADE 5, PLATED

14 4 BP3244 NUT, HEX LOCK, 1/2”-13, PLATED

SEALER SPRING, UPPER

SEALER SPRING, LOWER

75

LEGACY

SealPro II (AAM2857) Assembly,

Optional Sealer II Spring Add-on Kit 1 Row

Mounting
Spring
Add-on Kit

111

2

111

9

111

8

NOTE:

(2) (AM2489)
sealer spring
clevis must
be mounted
with the hole
to the front

1. Mount (2) (AM2489) sealer
spring clevis lower to arm
with clevis hole to the front.
Install (11) (BP3126) 1/2” x
1-1/2” grade 5, hex cap screw.
Secure with (9) (BP 3043) 1/2”
lock washer and (8) (BP 3042)
1/2” hex nut.

11

2. Mount (1) (AM2488) upper
sealer spring clevis to sealer
mounting bracket with (11)

(BP3126) 1/2” x 1-1/2” grade

5 hex cap screw. Secure
with (9) (BP3043) 1/2” lock
washer and (8) (BP3042)
1/2” hex nut.

3. Insert (5) (AM2492) spring
guide tube into (4) (AM2491)
spring collar bushing and
align the holes. Place in
lower clevis. Insert (12)

(BP3129) 1/2” x 3” hex cap

screw through clevis. Place
(10) (BP3050) 1/2” at washers
on both sides of bushing.
Secure with (14) (BP3244)
1/2” lock hex nut.

over tighten. Allow tubes to
pivot.

Do not

Front

111

2

Hole to Front

111

111

9

1

11

111

5

12

111

8

111

4

1.

2.

3.

4.

4. Place (6) (AP2997) spring
over (5) (AM2492) spring
guide tube.

5. Place (3) (AM2490) upper
spring tube over spring guide.
Insert (7) (AP3116) tube plug
in end of upper spring tube.

6. Lower spring assembly into
upper clevis and insert (13)

(BP3130) 1/2” x 3-1/2” hex

cap screw. Place (10) (BP 3050)

1/2” at washers on both

sides of upper tube. Secure
with (14) (BP3244) 1/2” lock
hex nut.

Allow tubes to pivot.

Do not over tighten.

14

111

9

13

6.

111

5

111

6

7

111

3

5.

76

LEGACY

SealPro II (AM2481) Assembly,

Sealer Hanger With Blade Mounting

AAM2481 ASSEMBLY, SEALPRO ll HANGER WITH BLADE

BOM ID Qty Item No Description

1 1 AM2482 HUB CAP RETAINER

2 1 AP2216 DECAL, BLU-JET, SMALL, 1-1/2” X 4”

3 2 AP2377 BEARING CONE, L44649

4 1 AP2380 HUB CAP

5 1 AP2426 PIN, COTTER, 5/32” X 1-3/4”

6 1 AP2811 NUT, SPINDLE, 1”-14

7 1 AP4209 GREASE SEAL, DOUBLE LIP

8 1 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

9 1 BP3043 WASHER, LOCK, 1/2”, PLATED

10 1 BP3072 GREASE ZERK, 1/4”-28

11 1 BP3126 HEX CAP SCREW, 1/2”-13 X 1-1/2”, GRADE 5, PLATED

12 1 BP3739 MACHINERY BUSHING, 1-1/2” OD X 1” ID X 14 GAUGE

13 1 EM3245 BLADE MOUNTING

14 1 EM3246 SEALER HANGER

14A 2 AP2376 BEARING CUP, L44610

77

LEGACY

Hitches

1

1

3e

3a

3c

3b

3d

2 2a

Ref. Part No. Req. Description

1. AM2144 1 Fabricated Truck Hitch

2. AP2864 1 Category IV Heat Treated Cast Wheatland Hitch 250-400+ HP 2” Pin
2a. AP2850 1 Category III Heat Treated Cast Wheatland Hitch 110-250 HP 1-1/2” Pin

78

Optional

3. AAM2424 1 Bracket, Second Hitch Storage
3a. AM2145 1 Bracket, Hitch Storage
3b. BP3001 2 Nut, Hex, 3/8”-16 Grade. 2 Plated.
3c. BP3002 2 Washer, Lock, 3/8”, Plated.
3d. BP3045 1 U-bolt, 3/8”-16 x 6”x 5”, Plated.
3e. BP3500 1 Pin, Hair Clip, 3/16”

LEGACY

AM2518 Top Wind Drop Leg Jack

AM2518 JACK, 9TWDL (TOP WIND DROP LEG)

BOM ID Qty Item No Description

1 1 AM2524 INTERMEDIATE TUBE WITH PLUNGER ASSEMBLY

2 1 AM2525 DROP LEG WITH PAD & HANDLE

3 1 AM2534 SCREW ASSEMBLY

3A 1 EM1736 BEARING SEAT

4 1 AM2539 TOP TUBE WITH BOLT ON MOUNTING

5 1 AP2407 SNAP RING, 1” EXTERNAL, HEAVY DUTY

6 1 AP2410 THRUST BEARING, NICE 609

7 1 EM1736 BEARING SEAT

8 2 EM1739 ROD

9 1 EM3016 9000# LABEL

79

LEGACY

Shanks

BOM ID Qty Item No Description

1 1 AP2063 SHANK, 1” X 2” FLAT

80

BOM ID Qty Item No Description

1 1 AP2125 SHANK, 1-1/4” X 2” EDGE BENT

LEGACY

Row Clamp

AAM2131 1” x 2” Rigid With Shank & Coulter Mount 6” x 6”

BOM ID Qty Item No Description

1 1 AM2148 CLAMP, SQUARE HOLE, 6” MOUNTING

2 1 AM2188 BACKING PLATE

3 1 AM2742 BRACKET, UNIVERSAL COULTER, 6” VERTICAL MOUNTING

4 1 AP2063 SHANK, 1” X 2” FLAT

5 1 AP2283 HOSE RETAINER, 6” X 6”

6 2 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

7 2 BP3035 WASHER, LOCK, 3/4”, PLATED

8 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

9 4 BP3043 WASHER, LOCK, 1/2”, PLATED

10 2 BP3128 HEX CAP SCREW, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

11 2 BP3229 BOLT, CARRIAGE, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

12 1 BP3578 HEX CAP SCREW, 3/4”-10 X 9-1/2”, GRADE 5, PLATED

13 1 CM2311 KNIFE WASHER

NOTE:

No threads
in shear
area

6 “x 6” Hose Retainer,
(AP2283-1) Place at
each shank to secure
coiled length of 3/8”
EVA hose as shown.

AAM2132 Edge Bent With Shank & Coulter Mount 6” x 6”

BOM ID Qty Item No Description

1 1 AM2699 BRACKET, SPRING BUNDLE FLATBACK

2 2 AM4891 BRACE, ANTI-ROTATION, EDGE BENT SHANK BRACKET

3 1 AM4893 BRACKET, EDGE BENT SHANK, RIGID MOUNT

4 1 AP2125 SHANK, 1-1/4” X 2” EDGE BENT

5 1 AP2283-1 HOSE RETAINER, 6” X 6”

6 6 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

7 6 BP3035 WASHER, LOCK, 3/4”, PLATED

8 4 BP3038 NUT, HEX, 5/8”-11, GRADE 2

9 4 BP3039 WASHER, LOCK, 5/8”, PLATED

10 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

11 4 BP3043 WASHER, LOCK, 1/2”, PLATED

12 4 BP3097 HEX CAP SCREW, 5/8”-11 X 1-1/2”, GRADED 5, PLATED

13 2 BP3128 HEX CAP SCREW, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

14 2 BP3142 HEX CAP SCREW, 3/4”-10 X 3-1/2”, GRADE 5, PLATED

15 2 BP3229 BOLT, CARRIAGE, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

16 2 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

17 1 CM2311 KNIFE WASHER

NOTE:

No threads
in shear
area

6” Tube brace placement

81

LEGACY

AAM2133 1” x 2” SCS With Shank & Coulter

AAM2133 Row Clamp 1” x 2” SCS With Shank & Coulter Mount 6” x 6”

BOM ID Qty Item No Description

1 1 AM2189 ASSEMBLY, SPRING BUNDLE, 1 X 2 SHANK

2 1 AM2699 BRACKET, SPRING BUNDLE FLATBACK, 4” X 6”

3 1 AP2063 SHANK, 1” X 2” FLAT

4 1 AP2283-1 HOSE RETAINER, 6” X 6”

5 4 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

6 4 BP3035 WASHER, LOCK, 3/4”, PLATED

7 5 BP3038 NUT, HEX, 5/8”-11, GRADE 2

8 5 BP3039 WASHER, LOCK, 5/8”, PLATED

9 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

10 4 BP3043 WASHER, LOCK, 1/2”, PLATED

11 4 BP3097 HEX CAP SCREW, 5/8”-11 X 1-1/2”, GRADE 5, PLATED

12 2 BP3128 HEX CAP SCREW, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

13 1 BP3135 HEX CAP SCREW, 5/8”-11 X 3-1/2”, GRADE 5, PLATED

14 2 BP3229 BOLT, CARRIAGE, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

15 2 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

16 1 CM2311 KNIFE WASHER

6” x 6” Hose Retainer,
(AP2283-1) Place
at each shank to
secure coiled length
of 3/8” EVA hose as
shown.

NOTE:

No threads
in shear
area

AM2189 Assembly, Spring Bundle, 1” x 2” Shank

BOM ID Qty Item No Description

1 2 AM2156 SPRING SLEEVE

2 1 AP2166 CAPPLUG, GC-5 GREASE ZERK

3 2 AP2407 SNAP RING, 1” EXTERNAL, HEAVY DUTY

4 2 BP3027 NUT, HEX LOCK, 3/4”-10, GRADE 2, PLATED

5 1 BP3034 NUT, HEX, 3/4”-10, GRD 2, PLATED

6 1 BP3035 WASHER, LOCK, 3/4”, PLATED

7 1 BP3072 GREASE ZERK, 1/4”-28

8 2 BP3104 SPRING, 2.64” OD X 8.625” OAL, .4375” WIRE DIAMETER

9 2 BP3105-1 SPRING PLUG

10 1 BP3106 U-BOLT, 3/4”-10 X 3-1/4”W X 11-3/4”L

11 1 BP3140 HEX CAP SCREW, 3/4”-10 X 2-1/2”, GRADE 5, PLATED

12 1 EM2959 PIVOT PIN, 1” X 6-13/16”

13 1 EM2978 SPRING BUNDLE BASE

14 1 EM3074 INSERT, 1 X 2 SHANK

82

LEGACY

AAM2134 1-1/4” SCS With Shank & Coulter

AAM2134 Row Clamp 1-1/4” Edge Bent SCS With Shank & Coulter Mount 6” x 6”

BOM ID Qty Item No Description

1 1 AM2155 ASSEMBLY, SPRING BUNDLE, EDGE BENT SHANK

2 1 AM2699 BRACKET, SPRING BUNDLE FLATBACK

3 1 AP2125 SHANK, 1-1/4” X 2” EDGE BENT

4 1 AP2283-1 HOSE RETAINER, 6” X 6”

5 6 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

6 6 BP3035 WASHER, LOCK, 3/4”, PLATED

7 4 BP3038 NUT, HEX, 5/8”-11, GRADE 2

8 4 BP3039 WASHER, LOCK, 5/8”, PLATED

9 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

10 4 BP3043 WASHER, LOCK, 1/2”, PLATED

11 4 BP3097 HEX CAP SCREW, 5/8”-11 X 1-1/2”, GRADE 5, PLATED

12 2 BP3128 HEX CAP SCREW, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

13 2 BP3141 HEX CAP SCREW, 3/4”-10 X 3”, GRADE 5, PLATED

14 2 BP3229 BOLT, CARRIAGE, 1/2”-13 X 2-1/2”, GRADE 5, PLATED

15 2 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

16 1 CM2311 KNIFE WASHER

6” x 6” Hose Retainer,
(AP2283-1) Place
at each shank to
secure coiled length
of 3/8” EVA hose as
shown.

NOTE:

No threads
in shear
area

AM2155 Assembly, Spring Bundle, Edge Bent Shank

BOM ID Qty Item No Description

1 2 AM2156 SPRING SLEEVE

2 1 AP2166 CAPPLUG, GC-5 GREASE ZERK

3 2 AP2407 SNAP RING, 1” EXTERNAL, HEAVY DUTY

4 2 BP3027 NUT, HEX LOCK, 3/4”-10, GRADE 2, PLATED

5 1 BP3072 GREASE ZERK, 1/4”-28

6 2 BP3104 SPRING, 2.64” OD X 8.625” OAL, .4375” WIRE DIAMETER

7 2 BP3105-1 SPRING PLUG

8 1 BP3106 U-BOLT, 3/4”-10 X 3-1/4”W X 11-3/4”L

9 1 EM2959 PIVOT PIN, 1” X 6-13/16”

10 1 EM2977 INSERT, EDGE BENT SHANK

11 1 EM2978 SPRING BUNDLE BASE

83

LEGACY

Manual Holder

AAM2640 MANUAL HOLDER WITH 6” X 6” MOUNTING

BOM ID Qty Item No Description

1 1 AM7640 BRACKET, MOUNTING, MANUAL HOLDER

2 1 AP4254 MANUAL HOLDER

3 3 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

4 3 BP3002 WASHER, LOCK, 3/8”, PLATED

5 1 BP3006 HEX CAP SCREW, 3/8”-16 X 1”, GRADE 5, PLATED

6 1 BP3351 U-BOLT, 3/8”-16 X 6”W X 7”L, PLATED

84

LEGACY

Impellicone and Mounting Hardware

AAM2635 IMPELLICONE 13 PORT, MOUNT & HARDWARE, 6” X 6”

BOM ID Qty Item No Description

1 1 AM7639 BRACKET, IMPELLICONE MOUNT

1A 1 CP2310 1’’ HOSE BARB

2 2 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

3 2 BP3002 WASHER, LOCK, 3/8”, PLATED

4 1 BP3351 U-BOLT, 3/8”-16 X 6”W X 7”L

5 1 CP2564 IMPELLICONE, 13 PORT

AAM2636 IMPELLICONE 18 PORT, MOUNT & HARDWARE, 6” X 6”

BOM ID Qty Item No Description

1 1 AM7639 BRACKET, IMPELLICONE MOUNT

1A 1 CP2310 1’’ HOSE BARB

2 2 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

3 2 BP3002 WASHER, LOCK, 3/8”, PLATED

4 1 BP3351 U-BOLT, 3/8”-16 X 6”W X 7”L

5 1 CP2565 IMPELLICONE, 18 PORT

85

LEGACY

SuperShooter III Parts AAM3514

86

BOM ID Qty Item No Description

1 1 AAM3514 SUPERSHOOTER III/ SQUIBB COUPLER/ BODYGUARD III

2 1 AM7634 VALVE MOUNTING, SUPERSHOOTER III

3 2 AM7635 DECAL PLATE, SUPER SHOOTER III

4 1 AM7660 COUPLER RELEASE PLATE, SUPERSHOOTER III

5 1 AM7661 COUPLER RELEASE HANDLE

6 1 AP2227 DECAL, SAFETY INSTRUCTION, NH3

7 1 AP2418 SPRING RETAINER WASHER

8 1 AP2972 DECAL, BLU-JET SUPER SHOOTER III

9 1 AP2973 DECAL, SUPERSHOOTERS III, HOOK-UP INSTRUCTIONS

10 1 AP2974 DECAL, SUPERSHOOTER III, SQUIBB COUPLER OPERATION

11 4 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

12 4 BP3002 WASHER, LOCK, 3/8”, PLATED

13 4 BP3015 WASHER, FLAT, 3/8”, PLATED

14 1 BP3084 SUPERSHOOTER SPRING

15 1 BP3087 WASHER, FLAT, 7/16, PLATED

16 1 BP3130 HEX CAP SCREW, 1/2”-13 X 3-1/2”, GRADE 5, PLATED

17 1 BP3244 NUT, HEX LOCK, 1/2”-13, PLATED

18 1 BP3504 PIN, HAIRCLIP, 1/8”

19 4 BP3701 BOLT, CARRIAGE, 3/8’’ - 16 X 1”, GRADE 5, PLATED

20 1 CCP2403 QUICK COUPLER SET, SQUIBB-TAYLOR, FM125-1000

20A 1 CP2405 QUICK COUPLER, SQUIBB, FEMALE, FM125-1100

20B 1 CP2406 QUICK COUPLER, SQUIBB, MALE, FM125-1200

21 1 CM2225 SUPERSHOOTER PEDESTAL

21A 1 AP2418 SPRING RETAINER WASHER

22 1 CM2249 BODY GUARD, SUPERSHOOTER III

23 1 CP2401 DUST CAP, CHAIN AND SNAP RING

24 1 CP2416 SNAP RING, 1-1/4” QUICK COUPLER

25 1 CP2423 ADAPTER 1-1/4” MPT X 1-3/4” ACME

26 1 CP2522 NIPPLE, HEX, 1-1/4” NPT, 3000 PSI TRIVALENT

27 1 CP2566 COUPLING, 1-1/4’’ FPT, PLATED

28 1 CP2837 VALVE, PRESSURE RELIEF, 250 PSI, A3184

29 2 CP2838 VALVE, BLEEDER, 104851-01

30 1 DP4081 STREET TEE, 5602-04

31 1 DP4657 PLUG, 1/4” NPT, STAINLESS STEEL

LEGACY

SuperShooter III Parts

66000136 Single Assembly, Less Distribution

BOM ID Qty Item No Description
1 1 66000136 SUPERSHOOTER III SINGLE ASSEMBLY, LESS DISTRIBUTION
2 1 AAM3514 SUPERSHOOTER III/ SQUIBB COUPLER/ BODYGUARD III
3 1 AM6277 SUPERSHOOTER RISER, AUTO-LOK HITCH
4 8 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
5 8 BP3002 WASHER, LOCK, 3/8”, PLATED
6 8 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED
7 6 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED
8 6 BP3043 WASHER, LOCK, 1/2”, PLATED
9 6 BP3050 WASHER, FLAT, 1/2”, PLATED
10 6 BP3126 HEX CAP SCREW, 1/2”-13 X 1-1/2”, GRADE 5, PLATED
11 1 CM2312 BRACKET, COUPLER, SINGLE, 1-1/4” NPT
11A 1 DP4655 COUPLING, 1-1/4” PIPE, FORGED STEEL, CLASS 3000
12 1 CP2593 HOSE, NH3, 1-1/4” X 64”
13 1 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP
14 1 CP2522 NIPPLE, HEX, 1- 1/4” NPT, 3000 PSI TRIVALENT
15 1 CP2870 STRAINER, NH3, 1-1/4” FPT 20 MESH, CONTINENTAL
16 1 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP

87

LEGACY

SuperShooter III Add-on Parts

Dual Assembly 66000137 and 66000136

88

LEGACY

SuperShooter III Add-on Parts

Dual Assembly 66000137 and 66000136

BOM ID Qty Item No Description

1 1 66000136 SUPERSHOOTER III SINGLE ASSY, LESS DISTRIBUTION
2 1 AAM3514 SUPERSHOOTER III/ SQUIBB COUPLER/ BODYGUARD III
3 1 AM6277 SUPERSHOOTER RISER, AUTO-LOK HITCH
4 4 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
5 4 BP3002 WASHER, LOCK, 3/8”, PLATED
6 4 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED
7 6 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED
8 6 BP3043 WASHER, LOCK, 1/2”, PLATED
9 6 BP3050 WASHER, FLAT, 1/2”, PLATED

10 6 BP3126 HEX CAP SCREW, 1/2”-13 X 1-1/2”, GRADE 5, PLATED

11 1 CP2593 HOSE, NH3, 1-1/4” X 64”
12 1 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP
13 1 66000137 DUAL SUPRSHTR III ADD-ON ASSEMBLY, W/HARDWARE & 64” HOSE

13A 1 AAM3514 SUPERSHOOTER III/ SQUIBB COUPLER/ BODYGUARD III
13B 1 AM7664 MOUNTING PLATE, DOUBLE SUPERSHOOTER
13C 12 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED
13D 12 BP3002 WASHER, LOCK, 3/8”, PLATED
13E 8 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED
13F 4 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED
13G 1 CM2313 BRACKET, COUPLER, DOUBLE, 1-1/4” NPT
13H 1 CP2522 NIPPLE, HEX, 1- 1/4” NPT, 3000 PSI TRIVALENT

13I 1 CP2593 HOSE, NH3, 1-1/4” X 64”

13J 1 CP2870 STRAINER, NH3, 1-1/4” FPT 20 MESH, CONTINENTAL

13K 2 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP

14 1 CP2522 NIPPLE, HEX, 1- 1/” NPT, 3000 PSI TRIVALENT
15 1 CP2870 STRAINER, NH3, 1-1/4” FPT 20 MESH, CONTINENTAL
16 1 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP

89

LEGACY

SuperShooter III Add-on Parts

66000136 Single Assembly With GDI

90

BOM ID Qty Item No Description

1 1 66000136 SUPERSHOOTER III SINGLE ASSEMBLY, LESS DISTRIBUTION
2 1 AM4553 HEAT EXCHANGER MOUNTING, AT5000
3 8 BP3038 NUT, HEX, 5/8”-11, GRADE 2
4 4 BP3039 WASHER, LOCK, 5/8”, PLATED
5 1 CCP2755 HEAT EXCHANGER ASSEMBLY, GDI 200A
6 1 CP2520 HOSE, NH3, 1-1/4” X 36”
7 1 CP2522 NIPPLE, HEX, 1- 1/4” NPT, 3000 PSI TRIVALENT
8 1 CP2870 STRAINER, NH3, 1-1/4” FPT 20 MESH, CONTINENTAL
9 2 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP

LEGACY

SuperShooter III Add-on Parts

Dual Assembly

Generic Assembly

BOM ID Qty Item No Description

1 1 PKG00234 NURSE TANK HITCH ASSEMBLY

2 1 66000136 SUPERSHOOTER III SINGLE ASSEMBLY

3 1 66000137 DUAL SUPRSHOOTER III ADD-ON ASSEMBLY, HARDWARE & HOSE

4 1 AM4553 HEAT EXCHANGER MOUNTING

5 1 CCP2755 HEAT EXCHANGER ASSEMBLY

6 1 CP2520 HOSE, NH3, 1-1/4” X 36”

6A 1 CP2520 HOSE, NH3, 1-1/4” X 36”

7 2 CP2522 NIPPLE, HEX, 1-1/4” NPT, 3000 PSI

8 1 CP2870 STRAINER, NH3, 1-1/4” FPT 20 MESH, CONTINENTAL

9 1 DP4037 TEE, 1-1/4”

10 2 DP4041 ELBOW, STREET, 1-1/4” EXTRA HEAVY

11 4 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP

12 8 BP3038 NUT, HEX, 5/8”-11, GRADE 2

13 4 BP3039 WASHER, LOCK, 5/8”, PLATED

91

92

LEGACY

GDI 200 With Pump Distribution (Rear Mount)

Parts (Bundle 20200119)

BOM ID Qty Item No Description

1 1 55000171 KIT, HEAT EXCHANGER, REAR OF FRAME MOUNT

2 1 AAM2089 ASSEMBLY, SPRING ADJUSTER

3 1 AAM2707 ASSEMBLY, HUB & SPINDLE, 511 HUB, 1-3/4” X 13”

4 1 AAM2750 WHEEL 5.00-15.4, 4 PLY 15 X 5 X 5, WHITE, 4 HOLE

5 1 AM2021 ADAPTER PLATE & HUB

6 1 AM2165 BRACKET, ROTARY TENSION ARM MOUNT

7 1 AM2180 UNIVERSAL PUMP MOUNTING PLATE

8 1 AM2181 GROUND DRIVE WHEEL FRAME

9 1 AM3326 BRACKET, PUMP EXTENSION

10 1 AM4856 BRACKET, MOUNTING, 6”

11 1 AP2190 SPROCKET, 5060 X, WITH HUB, 1’’ ROUND BORE, 1/4’’ KEYWAY

12 1 CCP2755 HEAT EXCHANGER ASSEMBLY

13 1 CCP2756 PUMP AND VALVE ASSEMBLY

14 1 PKG00012 PACKAGE, LARGE HARDWARE FOR 20200090

14A 1 AP2382 SPROCKET, IDLER, 15T #50 CHAIN, WITH CLEVIS ADAPTER

14B 2 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

14C 2 BP3035 WASHER, LOCK, 3/4”, PLATED

14D 1 BP3070 PIN, 3/4” X 2”

14E 1 BP3239 TENSIONER, RT1002

14F 1 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

14G 1 BP3502 PIN, 3/4” X 4-1/2”

14H 1 BP3510 PIN, 1” X 10”, PLATED

14I 1 CM2248 CHAIN, ROLLER, #50, 128 PITCH

14J 2 CP2310 1’’ HOSE BARB

14K 1 CP2474 REDUCER BUSHING 1” MP X 1/4” FP,

14L 1 CP2479 PLUG, SQUARE HEAD, 3/4” NPT

14M 1 CP2480 PLUG, 1’’

14N 1 CP2522 NIPPLE, HEX, 1-1/4” NPT, 3000 PSI TRIVALENT

14O 1 CP2870 STRAINER, NH3, 1-1/4” FPT, 20 MESH, CONTINENTAL

14P 2 CP2874 HOSE BARB, 1/2’’ X 3/4’’

14Q 1 CP2875 ELBOW, STREET, 1-1/4” NPT 45 DEGREE

14R 2 CP5043 KNIFE VAPOR TUBE 3/4’’ HOSE, WELD-ON

14S 1 DP3999 CROSS 1” FORGED

14T 1 DP4034 NIPPLE, CLASE, 1’’EXTRA HEAVY

14U 6 DP4086 CABLE TIE 11-3/8”

14V 6 DP4296 CABLE TIE 33”

14W 2 DP4397 SWIVEL, 1-1/4” MP X 1-1/4” FP

15 1 PKG00011 PACKAGE, SMALL HARDWARE FOR 20200090

15A 1 AP2103 CONNECTOR LINK #50 CHAIN

15AA 1 AP2103-BAR CONNECTOR LINK #50 CHAIN

15AB 1 AP2103-CONNECTOR CONNECTOR LINK #50 CHAIN

15AC 1 AP2103-LINK CONNECTOR LINK #50 CHAIN

15B 1 BM3527 1/4’’ X 1/4’’ X 1” KEY

15C 11 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

15D 12 BP3002 WASHER, LOCK, 3/8”, PLATED

15E 3 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED

15F 16 BP3015 WASHER, FLAT, 3/8”

15G 8 BP3038 NUT, HEX, 5/8”-11, GRADE 2

15H 4 BP3039 WASHER, LOCK, 5/8”, PLATED

15I 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

15J 4 BP3043 WASHER, LOCK, 1/2”, PLATED

15K 8 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED

15L 1 BP3116 HEX CAP SCREW, 3/8”-16 X 3, GRADE 5, PLATED

15M 4 BP3126 HEX CAP SCREW, 1/2”-13 X 1-1/2”, GRADE 5, PLATED

15N 3 BP3500 PIN, HAIR CLIP, 3/16”

15O 2 CP2313 HOSE CLAMP, WORM GEAR, 1/4”- 5/8” TUBING, STAINLESS STEEL

15P 6 CP2314 HOSE CLAMP, WORM GEAR, 1/2”- 1” TUBING, STAINLESS STEEL

16 1 PKG00025 PACKAGE, ORIFACE FITTING HARDWARE

16A 1 CP2541 ORIFICE PLATE #4916-63 JET STREAM

16B 1 CP2545 ORIFICE PLATE #4916-95 JET STREAM

16C 1 CP2557 ORIFICE PLATE #4916-35 JET STREAM

16D 1 CP5044 NOZZLE BODY, STEEL

16E 1 CP5045 NUT, SPRAY TIP

16F 1 CP5046 HOSE BARB INSERT, 3/8”, STAINLESS STEEL

17 1 CCM2325 1/4’’ Y-STRAINER

17A 1 AM3338 BRACKET, ORIFICE STRAINER MOUNT

17B 3 CP2308 HOSE BARB

17C 2 CP2313 HOSE CLAMP, WORM GEAR, 1/4”- 5/8” TUBING, STAINLESS STEEL

17D 1 CP2441 NIPPLE, 1/4’’ MP, STAINLESS STEEL

17E 1 CP2463 STRAINER, NH3, 1/4’’ FPT, 60 MESH, KECKLEY STYLE B

17F 1 CP2464 PLUG, 3/8’’ MP

18 1 CP25009 HOSE, EVA, 3/8” X 8’

19 2 CP25025 HOSE, EVA, 3/4” X 14’-8” (CP2515 CUT 2 EA.@14’-8”)

20 2 CP2895 HOSE, NH3, 1-1/4” NPT X 60” HIGH PRESSURE CRIMP

21 1 CP3001 HOSE, EVA, 1” REINFORCED X 180” with TIE & TAG

GDI 200 Pump Distribution (Rear Mount)

LEGACY

NOTE: Typical Layout,

Hose lengths and component
locations will vary by machine.

Parts (Bundle 20200119)

Generic Drawing
GDI placement will
depend on row spacing.

BOM ID Qty Item No Description

1 1 GDI 200, REAR MOUNT, 6” X 6” FRAME

2 1 CCP2755 HEAT EXCHANGER ASSEMBLY, GDI 200A

3 1 CCP2756 GDI 200A, PUMP AND VALVE ASSEMBLY

4 1 CP25009 HOSE, EVA, 3/8” 8 FT LONG

5 2 CP2515 HOSE, EVA, 3/4”

6 1 CP2593 HOSE , NH3, 1-1/4” NPT X 64” HIGH PRESSURE CRIMP

7 1 CP2594 HOSE , NH3, 1-1/4” NPT X 84” HIGH PRESSURE CRIMP

8 2 AM2636 IMPELLICONE 18 PORT, WITH MOUNT & HARDWARE, 6” X 6”

9 1 AAM3514 SUPERSHOOTER III/ SQUIBB COUPLER/ BODYGUARD III

10 2 CP2521 HOSE, EVA, 1” REINFORCED

11 1 CP2593 HOSE , NH3, 1-1/4” NPT X 64” HIGH PRESSURE CRIMP

12 2 CP5043 KNIFE VAPOR TUBE 3/4’’ HOSE, WELD-ON

NOTE: The following sub-assemblies in this manual are specic

to Bundle 20200119 for 6” X 6” frame rear mounts. Other bundles are

a v a i l a b l e f o r y o u r s p e c i  c f r a m e s i z e w i t h a m a j o r i t y o f p a r t s i n c o m m o n .

20200090 for 6” X 6” mid-frame mount.
20200070 for 4” X 6” front mount. Alternate part numbers will be listed where

necessary.

93

GDI 200 With Pump Distribution (Rear Mount)

LEGACY

Ref. Part No. Required. Description

1. 55000171 1 Kit Heat Exchanger, Rear

BOM ID Qty Item No Description

1 1 55000171 KIT, HEAT EXCHANGER, REAR OF FRAME MOUNT

1A 1 AM4015 HOSE RETAINER, CLOSED LOOP, 6” & 7” MOUNTING

1B 1 AM4553 HEAT EXCHANGER MOUNTING

1C 2 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

1D 2 BP3002 WASHER, LOCK, 3/8”, PLATED

1E 2 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

1F 2 BP3035 WASHER, LOCK, 3/4”, PLATED

1G 1 BP3045 U-BOLT, 3/8”-16 X 6”W X 5”L

1H 1 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

2. AAM2089 1 Spring Adjuster Assembly

BOM ID Qty Item No Description

2A 1 AM2191 CLEVIS SPRING ADJUSTER

2B 1 AM2192 SPRING CANISTER, GROUND DRIVE WHEEL

2C 2 AP2881 SPRING, 2.472” OD X 5.875” OAL, .468” WIRE DIAMETER

2D 1 BP3028 WASHER, FLAT, 1”, PLATED

2E 1 BP3223 NUT, HEX LOCK, 1”-8

2F 1 BP3572 TENSION BUSHING, 1-1/4” X 1” X 3/4” OAL

3. AAM2707 1 Hub & Spindle Assembly

BOM ID Qty Item No Description

3A 1 AP2023 BEARING CONE, LM 67048

3B 1 AP2024 BEARING CONE, LM 11949

3C 1 AP2029 PIN, COTTER, 5/32” X 1-1/2”

3D 5 AP2049 WHEEL BOLT, 1/2”- 20 X 1”

3E 1 AP2052 GREASE SEAL, CR 14974

3F 1 AP2053 HUB CAP, 1524

3G 1 AP2124 HUB WITH CUPS, 5 BOLT, 511300-5

3GA 1 AP2075 BEARING CUP, LM 11910

3GB 1 HUB HUB,5 BOLT, 5.5” BOLT CIRCLE, 4” PILOT

3GC 1 AP2524 BEARING CUP, LM 67010

3H 1 AP2169 SPINDLE, 1-3/4” X 13”, S7151-H-00

3I 1 AP2704 NUT, SPINDLE, 3/4”-16

3J 1 AP2705 WASHER, SPINDLE, 1-1/2” X 13/16” X .134”

4. AAM2750 1 Wheel 5.00 -15 4 Ply 15 x 5 x 5 White 4 hole

Parts and Assembly (Bundle 20200119)

BOM ID Qty Item No Description

4A 1 AP2002 TIRE, 5.00-15, 4 PLY SURE GRIP TRACTION

4B 1 AP2250 RIM, 15 X 5 X 5, WHITE WITH FOUR EXTRA HOLES

4C 1 AP2790 VALVE STEM, METAL

94

LEGACY

Parts List & Assembly For CCP2755

NH3 Heat Exchanger

AP2236

3

AP2263

6

AP2227

2

5

4

AP2262

AP2253

AP2262

5

AP2209

1

CCP2755 Heat Exchanger Assembly

BOM ID Qty Item No Description

1 1 AP2209 DECAL, CAUTION, GROUND DRIVE WHEEL,

2 1 AP2227 DECAL, SAFETY INSTRUCTION, NH3

3 1 AP2236 DECAL, NH3 DANGER

4 1 AP2253 DECAL, NH3 PUMP RATE CHART

5 2 AP2262 DECAL, GDI 200, 5-3/8” X 6-3/8”

6 1 AP2263 DECAL, DANGER, GDI 200

7 16 BP3080 NUT, HEX JAM, 5/8”-11, GRADE 2

8 1 CP2038 BUSHING

9 1 CP2837 VALVE, PRESSURE RELIEF, 250 PSI, A3184

10 1 CP2838 VALVE, BLEEDER, 104851-01

11 1 CP2957A CASTING, HEAT EXCHANGER OUTLET

12 1 CP2958A CASTING, HEAT EXCHANGER INLET

13 2 CP2965 O-RING

14 2 CP2966 O-RING

15 2 CP2967 O-RING

16 2 CP2984 BACK-UP RING, 8-258 N 300-90

17 4 CP2987 TIE ROD FOR GDI 200A

18 1 CP2987 TUBE, OUTSIDE

19 1 CP2988 TUBE, INTERMEDIATE

20 1 CP2989 TUBE, INSIDE

21 2 CP2991 BACK-UP RING, 5’’ ID X .05”

22 2 CP2992 BACK-UP RING, 2-3/4” ID X .05”

95

GDI 200 With Pump Distribution (Rear Mount)

LEGACY

13. CCP2756 GDI 200A, Pump & Valve Assembly

BOM ID Qty Item No Description

13 1 CCP2756 GDI 200A, PUMP AND VALVE ASSEMBLY

13A 1 CP2898 VALVE, SHUTOFF

13B 1 CP2899 PUMP, NH3

13C 4 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

13D 4 BP3002 WASHER, LOCK, 3/8”, PLATED

13E 2 BP3015 WASHER, FLAT, 3/8”

13F 4 BP3264 HEX CAP SCREW, 3/8”-16 X 1-3/4”, PLATED

13G 1 CP2899 PUMP, NH3

Parts (Bundle 20200119)

96

BOM ID Qty Item No Description

3 1 AAM2707 ASSEMBLY, HUB & SPINDLE, 511 HUB, 1-3/4” X 13”

4 1 AAM2750 WHEEL 5.00-15.4, 4 PLY 15 X 5 X 5, WHITE, 4 HOLE

5 1 AM2021 ADAPTER PLATE & HUB

11 1 AP2190 SPROCKET, 5060 X, WITH HUB, 1’’ ROUND BORE, 1/4’’ KEYWAY

14I 1 CM2248 CHAIN, ROLLER, #50, 128 PITCH

15AA 1 AP2103-BAR CONNECTOR LINK #50 CHAIN

15AB 1 AP2103-CONNECTOR CONNECTOR LINK #50 CHAIN

15AC 1 AP2103-LINK CONNECTOR LINK #50 CHAIN

15B 1 BM3527 1/4’’ X 1/4’’ X 1” KEY

15I 4 BP3042 NUT, HEX, 1/2”-13, GRADE 2, PLATED

15J 4 BP3043 WASHER, LOCK, 1/2”, PLATED

15M 4 BP3126 HEX CAP SCREW, 1/2”-13 X 1-1/2”, GRADE 5, PLATED

LEGACY

GDI 200 With Pump Distribution (Rear Mount)

Parts (Bundle 20200119)

BOM ID Qty Item No Description

2 1 AAM2089 ASSEMBLY, SPRING ADJUSTER

6 1 AM2165 BRACKET, ROTARY TENSION ARM MOUNT

7 1 AM2180 UNIVERSAL PUMP MOUNTING PLATE

8 1 AM2181 GROUND DRIVE WHEEL FRAME

9 1 AM3326 BRACKET, PUMP EXTENSION

10 1 AM4856 BRACKET, MOUNTING, 6”

14A 1 AP2382 SPROCKET, IDLER, 15T #50 CHAIN, WITH CLEVIS ADAPTER

14B 2 BP3034 NUT, HEX, 3/4”-10, GRADE 2, PLATED

14C 2 BP3035 WASHER, LOCK, 3/4”, PLATED

14D 1 BP3070 PIN, 3/4” X 2”

14E 1 BP3239 TENSIONER, RT1002

14F 1 BP3350 U-BOLT, 3/4”-10 X 6”W X 7-11/16”L, PLATED

14G 1 BP3502 PIN, 3/4” X 4-1/2”

14H 1 BP3510 PIN, 1” X 10”, PLATED

15C 11 BP3001 NUT, HEX, 3/8”-16, GRADE 2, PLATED

15D 12 BP3002 WASHER, LOCK, 3/8”, PLATED

15E 3 BP3005 HEX CAP SCREW, 3/8”-16 X 1-1/2”, GRADE 5, PLATED

15F 16 BP3015 WASHER, FLAT, 3/8”

15K 8 BP3115 HEX CAP SCREW, 3/8”-16 X 2”, GRADE 5, PLATED

15L 1 BP3116 HEX CAP SCREW, 3/8”-16 X 3”, GRADE 5, PLATED

15N 3 BP3500 PIN, HAIR CLIP, 3/16”

97