BlueStar PL030ML, PL048MLC, PL054ML, PL060ML, PY042ML Installation manual

...

INSTALLATION, USE AND CARE MANUAL

FOR PROFESSIONAL VENTILLATION FOR

THE HOME

MODELS: BS-PL SERIES, BS-PC SERIES

IMPORTANT!—PLEASE READ AND FOLLOW

1. THIS APPLIANCE WAS DESIGNED FOR EASE OF INSTALLATION AND OPERATION. HOWEVER, WE RECOMMEND THAT YOU READ ALL SECTIONS OF THIS MANUAL BEFORE YOU BEGIN INSTALLA- TION.

2. DO NOT REMOVE PERMANANTLY AFFIXED LABELS, WARNINGS OR DATA PLATES FROM YOUR APPLIANCE. THIS MAY VOID THE MANUFACTURER’S WARRANTY AND/OR HINDER EFFECTIVE SERVICING AND MAINTENANCE.

3. THESE INSTRUCTIONS ARE TO REMAIN WITH THE APPLIANCE AND THE CONSUMER IS TO RE- TAIN THEM FOR FUTURE REFERENCE.

4. PLEASE OBSERVE ALL LOCAL AND NATIONAL BUILDING CODES AND ORDINANCES. IF NO LO- CAL CODES ARE APPLICABLE, PLEASE FOLLOW ALL WIRING REQUIREMENTS IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 EDITION.

5. PLEASE CHECK WITH A QUALIFIED AND TRAINED INSTALLER OR YOUR LOCAL CODES FOR ANY MAKE UP AIR REQUIREMENTS.

6. THIS HOOD IS FOR RESIDENTIAL USE ONLY AND IS NOT DESIGNED FOR INSTALLATION OVER A COMMERCIAL PRODUCT.

7. MAKE SURE ALL POWER IS TURNED OFF AT THE MAIN BREAKER OR FUSE BOX BEFORE MAKING ANY CONNECTIONS.

8. TO AVOID RISK OF FIRE , ELECTRIC SHOCK, OR INJURY TO PERSONS, TURN OFF THE ELECTRICI- TY TO THE HOOD FROM THE POWER SUPPLY BEFORE CLEANING OR SERVICING.

This product is intended for domestic use only!

P/N 750301 Page 1

TABLE OF CONTENTS

Table of Contents ................................................................................................................................... 2

Safety Instructions ............................................................................................................................... 3-4

Introduction ............................................................................................................................................ 5

Welcome ................................................................................................................................................ 6

Handling & Unpacking .......................................................................................................................... 7

Packing list for your Vent Hood ....................................................................................................... 8-9

Pro Line Hoods ......................................................................................................................... 8

Pyramid Style Hoods ............................................................................................................... 9

Installation of Pro Line Series Dimensions…………. .. ……………………………………………………………………10 Site Preparation …………………………………………………………………………….. 11 The Correct Height …………………………………………………………………………...12 Duct Information ……………………………………………………………………………..13 Blower Installation …………………………………………………………………………...14 Custom Duct Installation ……………………………………………………………………..15

Installation of Pyramid Style

Dimensions ............................................................................................................................. 16

Site Preparation .................................................................................................................... 17

The Correct Height ................................................................................................................ 18

Duct Information ................................................................................................................... 19

Blower Installation ................................................................................................................ 20

Flue Installation ..................................................................................................................... 21

Wire Diagram ..................................................................................................................................... 22

Cleaning and Maintenance ................................................................................................................. 23

Warranty .......................................................................................................................................... 24-25

Performance Checklist .................................................................................................................... 26-27

P/N 750301 Page 2

IMPORTANT!—PLEASE READ AND FOLLOW

1. THIS APPLIANCE WAS DESIGNED FOR EASE OF INSTALLATION AND OPERATION. HOWEVER, WE RECOMMEND THAT YOU READ ALL SECTIONS OF THIS MANUAL BEFORE YOU BEGIN INSTALLA- TION.

2. DO NOT REMOVE PERMANANTLY AFFIXED LABELS, WARNINGS OR DATA PLATES FROM YOUR APPLIANCE. THIS MAY VOID THE MANUFACTURER’S WARRANTY AND/OR HINDER EFFECTIVE SERVICING AND MAINTENANCE.

3. THESE INSTRUCTIONS ARE TO REMAIN WITH THE APPLIANCE AND THE CONSUMER IS TO RE- TAIN THEM FOR FUTURE REFERENCE.

5. PLEASE CHECK WITH A QUALIFIED AND TRAINED INSTALLER OR YOUR LOCAL CODES FOR ANY MAKE UP AIR REQUIREMENTS.

6. THIS HOOD IS FOR RESIDENTIAL USE ONLY AND IS NOT DESIGNED FOR INSTALLATION OVER A COMMERCIAL PRODUCT.

7. MAKE SURE ALL POWER IS TURNED OFF AT THE MAIN BREAKER OR FUSE BOX BEFORE SERVIC- ING OR MAKING ANY CONNECTIONS.

8. TO AVOID RISK OF FIRE , ELECTRIC SHOCK, OR INJURY TO PERSONS, TURN OFF THE ELCTRICITY TO THE HOOD FROM THE POWER SUPPLY BEFORE CLEANING OR SERVICING.

WARNING!

TO REDUCE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOW- ING:

 USE THIS UNIT IN THE MANNER INTENDED

BY THE MANUFACTURER, IF YOU HAVE ANY QUESTIONS PLEASE CALL 610.374.7679

 BEFORE CLEANING OR SERVICING UNIT,

SWITCH POWER OFF TO THE UNIT AT THE SERVICE PANEL AND LOCK OUT THE SER- VICE PANEL. IF THE SERVICE PANEL CAN- NOT BE LOCKED OUT, PLEASE AFIX A WARNING DEVICE PROMINENTLY, SUCH AS A TAG, TO THE SERVICE PANEL.

WARNING!

TO REDUCE THE RISK OF A RANGETOP GREASE FIRE:

 NEVER LEAVE THE APPLIANCE UNATTEND-

ED DURING USE. BOIL-OVERS MAY OCCUR, CAUSING SPILLS WHICH MAY IGNITE.

 DO NOT USE WATER ON GREASE FIRES.

NEVER PICK UP A FLAMING PAN. IT IS REC- OMMENDED YOU PURCHASE A MULTI- PURPOSE DRY CHEMICAL OR FOAM-TYPE FIRE EXTINGUISHER FOR YOUR HOME. STORE IT IN CLOSE PROXIMITY TO YOUR APPLIANCES.

TO REDUCE THE RISK OF A RANGETOP GREASE FIRE (CONTINUED):

WARNING!

TO REDUCE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOW- ING:

 INSTALLATION WORK AND ELECTRICAL

WORK MUST BE PERFORMED BY QUALIFIED INDIVIDUALS IN ACCORDANCE WITH ALL APPLICABLE CODES AND STANDARDS, IN- CLUDING ALL FIRE RATED CONSTRUCTION

 DO NOT DAMAGE ANY EXISTING ELECTRI-

CAL OR HIDDEN UTILITIES WHEN DRILL- ING , CUTTING AND/OR REMOVING A WALL, CEILING OR FLOOR

 DUCTED FANS MUST VENT OUTDOORS  SUFFICIENT AIR IS REQUIRED TO PROPERLY

EXHAUST GASES THROUGH THE FLUE OF NATURAL AND LIQUID PROPANE FUELED COOKING EQUIPMENT TO AVOID ANY BACK DRAFTING. FOLLOW ALL LOCAL AND NA- TIONAL CODES AND STANDARDS FOR PROP- ER AIR REQUIREMENTS.

 USE ONLY METAL DUCTWORK  NEVER VENT DUCTED EXHAUST AIR INTO

ANOTHER ROOM OR GARAGE. TO REDUCE THE RISK OF FIRE AND TO PROPERLY VENT EXHAUST AIR, DUCT MUST VENT OUT- DOORS

 MATERIAL IN THIS MANUAL IS FOR REFER-

ENCE ONLY. DUE TO CONTINUOUS IM- PROVEMENT THE MANUAL MAY DIFFER FROM ACTUAL PRODUCT.

P/N 750301 Page 3

WARNING!

 IF YOU ARE FLAMING LIQUOR OR OTHER SPIRITS, AND YOUR APPLIANCE IS INSTALLED UNDER

A VENT HOOD, TURN THE FAN OFF. THE DRAFT CREATED COULD CAUSE THE FLAMES TO SPREAD OUT OF CONTROL.

 FOR YOUR SAFETY, NEVER USE YOUR APPLIANCE OR ANY OTHER COOKING APPLIANCE AS A

SPACE HEATER TO WARM OR HEAT THE ROOM.

 USE ONLY DRY POTHOLDERS. MOIST OR DAMP POTHOLDERS ON HOT SURFACES MAY RESULT

IN STEAM BURNS. DO NOT ALLOW POTHOLDERS TO TOUCH HOT BURNER AREAS. DO NOT USE A TOWEL OR OTHER BULKY MATERIAL AS A POTHOLDER.

 TO REDUCE THE RISK OF BURNS, IGNITION OF FLAMMABLE MATERIALS, AND SPILLAGE, THE

HANDLE OF ANY POT OR PAN SHOULD BE POSITIONED SO THAT IT DOES NOT EXTEND OVER ADJACENT BURNERS OR THE FRONT OF THE APPLIANCE.

 CLEAN VENTILATING FANS AND GREASE BAFFLES OFTEN. GREASE SHOULD NOT BE ALLOWED

TO ACCUMULATE .

 ALWAYS TURN HOOD ON WHEN OPERATING YOUR COOKING EQUIPMENT

WARNING!

TO REDUCE RISK OF INJURY TO PERSONS DUE TO A GREASE FIRE:  SMOTHER THE FLAMES WITH A CLOSE FITTING LID, COOKIE SHEET OR METAL TRAY, THEN

TURN OFF THE BURNER. TAKE CARE TO AVOID AND PREVENT BURNS. IF FLAMES DO NOT EX- TINGUISH, EVACUATE THE PRMISES AND CALL THE FIRE DEPARTMENT

 NEVER HANDLE OR PICK UP A FLAMING PAN.  DO NOT USE WATER, INCLUDING WET DISHCLOTHS, OR TOWELS. A VIOLENT STEAM EXPLO-

SION MAY ENSUE

 DO NOT TURN ON HOOD TO EVACUATE SMOKE. TURN OFF HOOD  USE AN EXTINGUISHER ONLY IF:

 YOU HAVE A CLASS ABC EXTINGUISHER AND YOU CAN OPERATE IT  THE FIRE IS SMALL AND CONTAINED WHERE IT STARTED  THE FIRE DEPARTMENT HAS BEEN NOTIFIED  YOU CAN FIGHT THE FIRE WITH YOUR BACK TOWARDS AN UNOBSTRUCTED EXIT

WARNING!

 THIS PRODUCT IS FOR GENERAL VENTILATION APPLICATIONS. DO NOT USE TO EXHAUST HAZ-

ARDOUS, FLAMMABLE, OR EXPLOSIVE MATERIALS

 PRIOR TO CLEANING OR SERVICING THE UNIT, SWITCH POWER OFF AT THE SERVICE PANEL

AND LOCK OUT THE PANEL. IF THE PANEL CANNOT BE LOCKED OUT, AFFIX A PROMINENT WARNING TAG TO THE SERVICE PANEL.

 DO NOT USE PORCELAIN OR ABRASIVE CLEANERS ON THIS PRODUCT. THIS MAY RESULT IN

COSMETIC DAMAGE TO THE SURFACE LIKE SCRATCHES AND/OR DISCOLORIZATION

 ALL BRASS TRIM PIECES REQUIRE SPECIAL CLEANING. DO NOT USE ABRASIVE CLEANERS OR

FURNITURE POLISH. THIS WILL RESULT IN DISCOLORIZATION TO THE BRASS SURFACE

P/N 750301 Page 4

Since 1880, we have been dedicated to quality! We believe that our success can only be measured by the continuing success of our customers. We achieve customer satisfaction by ensuring that each of our employees understands, meets and exceeds customer expectations. We establish and maintain an environment that encourages all employees to pursue continuous improvement in qual- ity and productivity.

Our quality policy is monitored by the highest levels of management.

We hope you enjoy your new appliance and we THANK YOU again for believing in our product as much as we do.

The staff and team at Prizer Stove Works !

PRO LINE HOOD

PYRAMID HOOD

P/N 750301 Page 5

WELCOME!

...to the exciting world of BlueStar™ cooking! You have purchased one of the finest appliances available for home use, which shows that you take cooking seriously. As the owner of a new BlueStar appliance you can look forward to years of cooking enjoyment. You will prepare meals with the speed and accuracy of a professional chef right in your own kitchen! All equipment is designed and manufactured to the highest quality standards in the in- dustry specifically to meet the needs of the world’s most demanding chefs: you. From simmering to sautéing, bak- ing and broiling these versatile appliances provide the flexibility you need in any cooking application. Commercial styling adds a touch of elegance to your kitchen like no other appliance can. What’s more, this high quality, high - performance appliance is backed by our professional service network from coast to coast to provide you with quick, competent technical service should the need arise. Please take a few moments now to fill in the information below for your future reference. In the event you require parts or service, this information will be needed to ensure you receive the highest quality service we can provide.

DATE OF PURCHASE

DEALER’S NAME

DEALER’S ADDRESS

DATE OF INSTALLATION

INSTALLER’S NAME

INSTALLER’S ADDRESS

MODEL NUMBER

SERIAL NUMBER

NOTE: WARRANTY SERVICE MUST BE PERFORMED BY AN AUTHORIZED SERVICE AGENT. YOU MAY REQUEST WARRANTY SERVICE BY CALLING 800-449-8691. YOU MAY ALSO REQUEST SER- VICE VIA THE INTERNET BY SUBMITTING THE SERVICE REQUEST FORM AT WWW.BLUESTARCOOKING.COM

P/N 750301 Page 6

HANDLING

 REMOVE ALL WATCHES, BELT BUCKLES, JEWELRY, RINGS AND ANY CLOTHING WITH

METAL BUTTONS OR SNAPS TO PREVENT DAMAGE TO THE HOOD.

 WHEN YOU BEGIN THE INSTALLATION PROCESS REMOVE THE HOOD FROM IT’S ORIGI-

NAL CARTON AND PLACE THE HOOD ON A CLEAN, NON-ABRASIVE BLANKET.

 INSPECT THE HOOD CAREFULLY FOR ANY DAMAGE OR IMPERFECTIONS BEFORE YOU

BEGIN TO INSTALL THE HOOD. IF ANY DAMAGE OR IMPERFECTIONS EXIST, RECARTON THE HOOD AND CALL YOUR DEALER IMMEDIATELY, DO NOT INSTALL A DAMAGED HOOD.

 IT IS HIGHLY RECOMMENDED THAT RUBBER GLOVES BE USED TO PREVENT SCRATCH-

ES ON THE HOOD AND TO PROVIDE YOU WITH A FIRM GRIP.

 WHEN REMOVING THE HOOD FROM THE CARTON LOCATE THE FILTERS. THE FILTERS

ARE PACKED SEPARATELY.

DO NOT REMOVE HOOD FROM ORIGINAL CARTON UNTIL YOU ARE READY TO IN- STALL

UNPACKING

 CHECK THE PACKAGE FOR DAMAGE. IF ANY DAMAGE IS VISIBLE YOU SHOULD MARK

THE BILL OF LADING YOU SIGN THAT THERE MAY BE CONCEALED DAMAGE.

 INSURE THE CONTAINER IS UPRIGHT. IF THE CONTAINER IS NOT UPRIGHT MAJOR DAM-

AGE CAN OCCUR TO YOUR APPLIANCE. IF DAMAGE IS DISCOVERED, DO NOT REFUSE DELIVERY. CONTACT THE DEALER AND FILE APPROPRIATE FREIGHT CLAIMS. SAVE ALL PACKAGING MATERIAL. DO NOT CONTACT THE MANUFACTURER. YOUR APPLI- ANCE WAS SHIPPED FROM THE DEALER YOU PURCHASED IT FROM. SHIPPING DAMAGE CLAIMS ARE TO BE RESOLVED BETWEEN THE CUSTOMER, SHIPPING CARRIER AND DEALER. THE MANUFACTURER MAY ASSIST IN RESOLVING ANY SUCH CLAIMS, BUT SUCH ASSISTANCE DOES NOT RELIEVE YOU OF YOUR RESPONSIBILITY.

 MOVE THE CONTAINER AS CLOSE TO ITS INSTALLATION LOCATION AS POSSIBLE. THIS

WILL REDUCE MOVING AND HANDLING YOUR APPLIANCE ONCE IT IS OUT OF ITS SHIP- PING CONTAINER

 DO NOT DISCARD PACKAGING WITHOUT FIRST LOCATING THE FILTERS  INSPECT ALL MOLDED PACKAGING BEFORE DISCARDING

ANY DAMAGE MUST BE REORTED BEFORE INSTALLING THE HOOD. ONCE THE HOOD HAS BEEN INSTALLED, NO RETURN WILL BE AC- CEPTED!

MAKE SURE BLOWERS ARE FREE FROM OBSTRUCTIONS (PACKING AND DEBRIS). TEST RUN BLOWERS BEFORE FINALIZING INSTALLATION. CHECK WITH MANUFACTURER BE- FORE ATTEMPTING TO USE OTHER THAN BLUESTAR BLOWER SYSTEMS. FOR TECH- NICAL INFORMATION CONTACT BLUESTAR SERVICE (610.376.7479)

P/N 750301 Page 7

PACKING LIST FOR PRO LINE HOOD SERIES

PL30240——24” depth

 No blower (Sold and Packaged Separately)  Two (2) Stainless Steel Baffle Filters  Two (2) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram

PL36240, PL42240—24” depth

 No blower (Sold and Packaged Separately)  Four (4) Stainless Steel Baffle Filters  Two (2) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram

PL48240 , PL54240, —- 24" Depth

 No blower (Sold and Packaged Separately)  Six (6) Stainless Steel Baffle Filters  Three (3) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram

PL60240, PL66240 — 24" Depth

 No blower (Sold and Packaged Separately)  Six (6) Stainless Steel Baffle Filters  Three (3) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram

P/N 750301 Page 8

PACKING LIST FOR PYRAMID STYLE HOOD SERIES

PC30240—24” depth

 No blower (Sold and Packaged Separately)  Two (2) Stainless Steel Baffle Filters  Two (2) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram  Duct cover sold packed in separate box (2 of2)

PC36240, PC42240—24” depth

 No blower (Sold and Packaged Separately)  Four (4) Stainless Steel Baffle Filters  Two (2) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram  Duct cover sold packed in separate box (2 of2)

PC48240 , PC54240, —- 24" Depth

 No blower (Sold and Packaged Separately)  Six (6) Stainless Steel Baffle Filters  Three (3) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram  Duct cover sold packed in separate box (2 of2)

PC60240, PC66240 — 24" Depth

P/N 750301 Page 9

+ 20 hidden pages