Blue Sonic Multimedia PC User Manual

V13.1.00

I

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©February 2013

Trademarks

Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.

II

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc­tive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux­embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov­enia.

EuP-Standby and Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC)
regulations on power consumption in off mode or standby mode:

• Standby Mode < 2W

• Off Mode < 1W

III

Preface

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has at­tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas mo st q uality marking s are voluntary.

IV

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance
could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc e d ra di o/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference.
And

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

V

Preface

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-l ocated or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environ ment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.

VI

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter – AC Input 100 -

240V, 50 - 60Hz, DC Output 19V, 6.3A OR 19.5V, 6. 15 A).

This Computer’s Optical Device is a Laser Class 1 Product

VII

Preface

Instructions for Care and Operation

The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g proc edur es for t he computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost.

5. Take care when using peripheral devices.

VIII

Preface

Power Safety

The computer has specific power requirements:

•When you want to unplug the power cord, be sure to disconnect it by the plug head, not by
its wire.

•Make sure the socket and any extension cord(s) you use can su pport the total current load
of all the connected devices.

•Before cleaning the computer, make sure it is disconnected from any external power sup­plies.

Do not plug in the power
cord if you ar e wet.

Do not use the power cord if
it is broken.

Do not place heavy objects
on the power cord.



Power Safety

Warning

Before you undertake
any upgrade proce­dures, make sure that
you have turned off the
power, and discon­nected all peripherals
and cables (including
telephone lines and
power cord).

You must also remove
your battery in order to
prevent accidentally
turning the machine
on. Before removing

the battery discon­nect the AC/DC
adapter from the
computer.

IX

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides
the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansio n or swelling, however this is part of the battery’s safety mecha-

nism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-

ture environments, and do not store unused batteries for extended per iods.

See also the general battery precautionary information overleaf for further information.

X

Preface

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replac ement to your service repre sentati ve or qual-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteri es

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.

XI

Preface

Cleaning

Do not apply cleaner directly to the computer, use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord is damaged or frayed.

• If the computer has been exposed to any liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

XII

Preface

Ergonomics

We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are
some suggestions on how to position and use the computer:

• The top third of the LCD (screen) should be at eye-level or slightly below.

• The LCD should be at least 18"/45cm. directly in front of you.

• If the screen resolution makes you strain to read, then adjust the resolution to something more co mfortable (see “Video

Features” on page 1 - 34).

• Angle the LCD (see “Tilting the LCD Screen” on page 1 - 8) so that it doesn’t reflect any light into your eyes.

• Use a chair which offers good back support (especially lower-back). The seat should allow your feet to rest flat on the

floor or on a footrest directly in front of you.

• If possible, illuminate your work area with natural daylight or use a steady-glowing (non-flickering) light source.

• Place the keyboard and mouse so that your arms are at your sides and your forearms are roughly parallel to the floor.

Your wrists should flex slightly downward as you work. Your neck and shoulders should also be relaxed.

• Take a break from the computer. Get up, stretch, flex your wrists, walk about, and look at something else for about 10

minutes every hour.

XIII

Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.

• Position the display to avoid glare or reflecti ons from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.



Carrying the Computer

We strongly recommend using both hands to move the computer (one hand gripping the handle area and the other grip­ping the computer) to avoid accidentally dropping it. Be careful that objects such as belt buckles etc. do not scratch the
screen while it is being carried.

XIV

Preface

Wall Mounting Information

The computer may be mounted on a wall for display. The system meets VESA MIS-D Standard (100mm *
100mm) for wall mounting. However if you intend to wall mount the system please contact your service center
for information in order to avoid personal injury, or damage to the computer.

XV

Preface

Contents

Notice .............................................................................................................................................................I

EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II

FCC Statement ............................................................................................................................................IV

FCC RF Radiation Exposure Statement: .....................................................................................................V

Instructions for Care and Operation ......................................................................................................... VII

Power Safety ............................................................................................................................................VIII

Polymer Battery Precautions ......................................................................................................................IX

Battery Precautions ......................................................................................................................................X

Cleaning ......................................................................................................................................................XI

Servicing .....................................................................................................................................................XI

Ergonomics ............................................................................................................................................... XII

Wall Mounting Information .....................................................................................................................XIV

Quick Start Guide

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Not Included ..............................................................................................................................................1-3

System Software ........................................................................................................................................1-4

System Startup ...........................................................................................................................................1-5

XVI

Preface

System Map: Front View - Model A .........................................................................................................1-6

System Map: Front View - Model B .........................................................................................................1-7

Tilting the LCD Screen ..............................................................................................................................1-8

Buttons & LED Indicators (Win 8) .........................................................................................................1-10

System Map: Left View ...........................................................................................................................1-11

HDMI-In Port ..........................................................................................................................................1-12

Mode Toggle ............................................................................................................................................1-12

Menu Button ............................................................................................................................................1-13

HDMI-In Port in Sleep or Hibernate Modes ...........................................................................................1-15

System Map: Right View .........................................................................................................................1-16

System Map: Rear View ..........................................................................................................................1-17

Wireless Keyboard & Mouse USB Transceiver ......................................................................................1-18

Windows 8 Touch Screen Controls/Gestures ..........................................................................................1-19

Touch Keyboard ......................................................................................................................................1-21

Windows Control Panel ...........................................................................................................................1-23

Windows 8 Start Screen & Desktop ........................................................................................................1-24

Windows 8 Charms Bar ...........................................................................................................................1-28

Windows 8 Control Panel ........................................................................................................................1-30

Windows 8 Taskbar .................................................................................................................................1-33

Video Features .........................................................................................................................................1-34

Power Options .........................................................................................................................................1-37

Running Metro UI Apps ..........................................................................................................................1-38

XVII

Preface

Features & Components

Overview ....................................................................................................................................................2-1

Hard Disk Drive .........................................................................................................................................2-2

Optical (CD/DVD) Device ........................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3

Handling CDs or DVDs .............................................................................................................................2-4

DVD Regional Codes ................................................................................................................................2-5

Multi-in-1 Card Reader ..............................................................................................................................2-6

ExpressCard Slot .......................................................................................................................................2-7

Inserting and Removing ExpressCards ......................................................................................................2-7

Audio Features ...........................................................................................................................................2-8

Setup for Audio Recording ........................................................................................................................2-9

Keyboard Shortcuts - Windows 8 ............................................................................................................2-10

Power Management

Overview ....................................................................................................................................................3-1

The Power Sources ....................................................................................................................................3-2

AC/DC Adapter .........................................................................................................................................3-2

Battery ........................................................................................................................................................3-2

Turning On the Computer ..........................................................................................................................3-3

Power Plans ...............................................................................................................................................3-4

Power-Saving States ..................................................................................................................................3-6

XVIII

Preface

Sleep ..........................................................................................................................................................3-6

Hibernate ....................................................................................................................................................3-7

Shut down ..................................................................................................................................................3-7

Configuring the Power Buttons .................................................................................................................3-8

Resuming Operation ................................................................................................................................3-10

Battery Information .................................................................................................................................3-12

Conserving Battery Power .......................................................................................................................3-13

Battery Life ..............................................................................................................................................3-14

New Battery .............................................................................................................................................3-14

Recharging the Battery with the AC/DC Adapter ...................................................................................3-14

Proper handling of the Battery Pack ........................................................................................................3-15

Battery FAQ .............................................................................................................................................3-16

Drivers & Utilities

What to Install ............................................................................................................................................4-1

Driver Installation (Windows 8) ................................................................................................................4-2

Updating/Reinstalling Individual Drivers ..................................................................................................4-5

User Account Control ................................................................................................................................4-6

Windows Security Message .......................................................................................................................4-6

New Hardware Found ................................................................................................................................4-6

Driver Installation Procedure .....................................................................................................................4-7

Chipset .......................................................................................................................................................4-7

XIX

Preface

Video ..........................................................................................................................................................4-7

LAN ...........................................................................................................................................................4-7

ExpressCard/Card Reader ..........................................................................................................................4-7

MEI Driver .................................................................................................................................................4-7

Audio .........................................................................................................................................................4-7

Windows Experience Index .......................................................................................................................4-8

Optional Drivers ........................................................................................................................................4-9

BIOS Utilities

Overview ....................................................................................................................................................5-1

The Setup Utility ........................................................................................................................................5-2

Failing the POST .......................................................................................................................................5-3

Fatal Errors ................................................................................................................................................5-3

Non-Fatal Errors ........................................................................................................................................5-3

Setup Screens .............................................................................................................................................5-4

Main Menu .................................................................................................................................................5-5

System Time & Date (Main Menu) ...........................................................................................................5-5

SATA Port # (Main Menu) ........................................................................................................................5-6

System/Extended Memory: (Main Menu) .................................................................................................5-6

MB Series / BIOS Revision / KBC/EC firmware Revision ......................................................................5-6

Advanced Menu .........................................................................................................................................5-7

Advanced Chipset Control (Advanced Menu) ..........................................................................................5-7

XX

Preface

Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-8

Total Graphics Memory (Advanced Menu > Advanced Chipset Control) ................................................5-8

SATA Mode Selection (Advanced Menu) ................................................................................................5-8

Boot Logo (Advanced Menu) ....................................................................................................................5-9

Power On Boot Beep (Advanced Menu) ...................................................................................................5-9

Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-9

Super IO Configuration (Advanced Menu) ...............................................................................................5-9

Security Menu ..........................................................................................................................................5-10

Password on boot (Security Menu) ..........................................................................................................5-10

Set Supervisor Password (Security Menu) ..............................................................................................5-11

Set User Password (Security Menu) ........................................................................................................5-11

Interface Items (Security Menu) ..............................................................................................................5-11

Secure Boot (Advanced Menu) ...............................................................................................................5-12

Configuration (Security Menu) ................................................................................................................5-12

Boot Menu ...............................................................................................................................................5-13

Fast Boot (Boot Menu) ............................................................................................................................5-14

UEFI Boot (Boot Menu > OS Select) .....................................................................................................5-14

Boot Option Priorities (Boot Menu) ........................................................................................................5-14

Wake-up On LAN (Boot Menu) ..............................................................................................................5-14

OS Select (Boot Menu) ............................................................................................................................5-14

Exit Menu ................................................................................................................................................5-15

XXI

Preface

Upgrading The Computer

Overview ....................................................................................................................................................6-1

When Not to Upgrade ................................................................................................................................6-2

Removing the Battery ................................................................................................................................6-3

Inserting the Battery ..................................................................................................................................6-5

Removing the Rear Component Cover ......................................................................................................6-6

Inserting the Rear Cover ............................................................................................................................6-8

Upgrading the Hard Disk Drive/SSD ........................................................................................................6-9

Removing the 3.5" (88.9mm) HDD .........................................................................................................6-10

Replacing the Brackets & Screws in the 3.5" (88.9mm) HDD ...............................................................6-12

Removing the 2.5" (63.5mm) HDD or SSD ............................................................................................6-14

Upgrading the Optical (CD/DVD) Device Drive ....................................................................................6-17

Upgrading the System Memory (RAM) ..................................................................................................6-18

Upgrading the Processor ..........................................................................................................................6-21

Modules & Options

Overview ....................................................................................................................................................7-1

PC Camera Module (Windows 8) ..............................................................................................................7-2

PC Camera Audio Setup ............................................................................................................................7-3

Metro UI Camera App ...............................................................................................................................7-4

Taking Pictures/Capturing Video ..............................................................................................................7-6

Wireless LAN Module (Windows 8) .........................................................................................................7-8

XXII

Preface

3rd Party 802.11b/g/n Driver Installation ..................................................................................................7-9

Intel® WLAN Driver Installation ............................................................................................................7-10

WLAN Configuration in Windows 8 ......................................................................................................7-11

Windows Mobility Center .......................................................................................................................7-17

Intel® Wireless Display Application .......................................................................................................7-18

Intel® WiDi Application Installation ......................................................................................................7-19

Intel® Wireless Music Driver Installation ...............................................................................................7-19

Intel® WiDi Application Configuration ..................................................................................................7-20

Bluetooth & WLAN Combo Module (Windows 8) ................................................................................7-23

3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-24

Intel Bluetooth Combo Driver Installation ..............................................................................................7-25

Bluetooth Configuration in Windows 8 ...................................................................................................7-26

Trusted Platform (Security) Module ........................................................................................................7-30

Enabling & Activating TPM ....................................................................................................................7-31

Trusted Platform Module (TPM) Driver Installation ..............................................................................7-33

Initializing TPM .......................................................................................................................................7-34

Infineon Security Platform Settings Tool ................................................................................................7-36

Troubleshooting

Overview ....................................................................................................................................................8-1

Basic Hints and Tips ..................................................................................................................................8-2

Backup and General Maintenance .............................................................................................................8-3

XXIII

Preface

Viruses .......................................................................................................................................................8-4

Upgrading and Adding New Hardware/Software ......................................................................................8-5

Problems & Possible Solutions ..................................................................................................................8-7

Interface (Ports & Jacks)

Overview ...................................................................................................................................................A-1

Computer Ports and Jacks .........................................................................................................................A-2

Card Reader Port .......................................................................................................................................A-2

DC-In Jack ................................................................................................................................................A-2

HDMI-In Port ...........................................................................................................................................A-2

HDMI-Out Port .........................................................................................................................................A-2

Headphone-Out Jack .................................................................................................................................A-2

Microphone-In Jack ..................................................................................................................................A-3

PS/2 Type Keyboard & Mouse Ports ........................................................................................................A-3

RJ-45 LAN Jack .......................................................................................................................................A-3

RS-232 COM/Serial Ports ........................................................................................................................A-3

Security Lock Slot ....................................................................................................................................A-4

USB 2.0/1.1 Ports .....................................................................................................................................A-4

USB 3.0 Port .............................................................................................................................................A-4

Intel Video Driver Controls

Intel Video Driver Installation ..................................................................................................................B-1

Video .........................................................................................................................................................B-1

XXIV

Preface

Dynamic Video Memory Technology ......................................................................................................B-1

Intel® Graphics & Media Control Panel ..................................................................................................B-2

Display Devices & Options ......................................................................................................................B-5

Attaching Other Displays .........................................................................................................................B-6

To Configure Displays from Devices (Charms Bar) ................................................................................B-8

HDMI Audio Configuration .....................................................................................................................B-9

Specifications

Processor ...................................................................................................................................................C-2

Core Logic ................................................................................................................................................C-2

Display ......................................................................................................................................................C-2

Memory .....................................................................................................................................................C-2

Video Adapter ...........................................................................................................................................C-3

BIOS .........................................................................................................................................................C-3

Storage ......................................................................................................................................................C-3

Audio ........................................................................................................................................................C-3

Interface ....................................................................................................................................................C-3

Card Reader ..............................................................................................................................................C-3

Slots ..........................................................................................................................................................C-3

Communication .........................................................................................................................................C-3

Power Management ..................................................................................................................................C-4

Power ........................................................................................................................................................C-4

XXV

Preface

Security .....................................................................................................................................................C-4

Operating System ......................................................................................................................................C-4

Design Features ........................................................................................................................................C-4

LED Indicators ..........................................................................................................................................C-4

Environmental Spec ..................................................................................................................................C-4

Physical Dimensions & Weight ................................................................................................................C-4

Windows 7

Overview ...................................................................................................................................................D-1

Turning On the Computer .........................................................................................................................D-2

Buttons & LED Indicators (Win 7) ..........................................................................................................D-3

On Screen Display Indicators/Buttons ......................................................................................................D-4

Windows 7 Start Menu & Control Panel ..................................................................................................D-5

Video Features ..........................................................................................................................................D-6

Configuring an External Display in Windows 7 .......................................................................................D-8

HDMI Audio Configuration ...................................................................................................................D-11

Power Options ........................................................................................................................................D-12

Audio Features ........................................................................................................................................D-13

Driver Installation ...................................................................................................................................D-15

Updating/Reinstalling Individual Drivers................................................................................................D-17

User Account Control..............................................................................................................................D-18

Windows Security Message.....................................................................................................................D-18

XXVI

Preface

New Hardware Found..............................................................................................................................D-18

Driver Installation Procedure...................................................................................................................D-19

Optional Drivers ......................................................................................................................................D-22

PC Camera Module (Windows 7) ...........................................................................................................D-23

Wireless LAN Module (Windows 7) ......................................................................................................D-31

Connecting to a Wireless Network in Windows 7...................................................................................D-36

Connecting to a Wireless Network Using Intel® PROSet Wireless.......................................................D-39

Intel® My WiFi Configuration................................................................................................................D-41

Windows Mobility Center .......................................................................................................................D-50

Intel® Wireless Display Application (Windows 7) ................................................................................D-51

Bluetooth & WLAN Combo Module (Windows 7) ...............................................................................D-56

Bluetooth Connection Problems .............................................................................................................D-63

Trusted Platform (Security) Module (Windows 7) .................................................................................D-67

Initializing TPM.......................................................................................................................................D-71

Infineon Security Platform Settings Tool................................................................................................D-73

Tablet PC Input Options .........................................................................................................................D-81

Overview 1 - 1

Quick Start Guide

1

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, Multi-in-1 card reader, ExpressCard/34/54) Audio & Printer.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth & WLAN Combo and

Trusted Platform (Security) modules (some of which may be optional depending on your pur­chase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on the Intel video driver controls.

• Appendix C The computer’s specification.

• Appendix D Information related to the Windows 7 operating system.

1 - 2 Overview

Quick Start Guide

1

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on

page 6 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.



Notes

Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.

Overview 1 - 3

Quick Start Guide

1

Not Included

Operating Systems (e.g. Windows 8) and applications (e.g. word processing, spreadsheet and database programs)
have their own manuals, so please consult the appropriate manuals.



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com­puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed in Table 4 - 1, on page 4 - 4. You will be unable to use most advanced controls until the necessary drivers and util­ities are properly installed. If your system hasn’t been properly configured (your service representative may have already
done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.

Ports and Jacks

See “Computer Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your com­puter to communicate with external devices, connect to the internet etc.

1 - 4 Overview

Quick Start Guide

1

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the Windows 7 (with Service Pack 1 in-
stalled) and Windows 8 operating systems are supported.

The majority of this menu covers information covers information related to the Windows 8 operating system,
however for specific information on the Windows 7 operating system see Appendix D.

Note: In order to run Windows without limitations or decreased performance, your computer requires a mini-
mum 1GB of system memory (RAM).



Windows 7/8 OS

In order to run Windows 7 or 8 (32 Bit) without limitations or decreased performance, your computer requires a minimum

1GB of system memory (RAM), however if you are running Windows 7 or 8 (64 bit) your computer requires a minimum
2GB of system memory (RAM).

System Startup 1 - 5

Quick Start Guide

1

System Startup

1. Remove all packing materials, CDs/DVDs and floppy disks etc.

2. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse etc.)

3. Attach the AC/DC adapter to the DC-In jack at the rear of the LCD, then plug the AC power cord into an outlet,

and connect the AC power cord to the AC/DC adapter.

4. Push the power button at the front of the computer (along the bottom of the LCD) to turn the computer “on”.

Figure 1 - 1 - AC/DC Adapter Plugged-In/Power Button

Power Button (located along the bottom of the LCD)



Shutdown

Note that you should always shut your computer down by
choosing the Shut Down command from the Power item in

Settings in the Charms Bar (use the Windows Logo Key
+ C key combination to access the Charms Bar) in Win­dows 8. This will help prevent hard disk or system prob-

lems.

1 - 6 System Map: Front View - Model A

Quick Start Guide

1

System Map: Front View - Model A

Figure 1 - 2 - Front View - Model A

1. Optional Built-In PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Power Button

6. Function Buttons

7. Power & System Activity LED
Indicators

8. Speakers

1

2

5

4

6

3

7

88

5

67



Multi Touch Screen

Note that Model B computers incorporate a
touch screen, Model A computers do not.

System Map: Front View - Model B 1 - 7

Quick Start Guide

1

System Map: Front View - Model B

Figure 1 - 3 - Front View - Model B

1. Optional Built-In PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD with Multi Touch Screen

5. Power Button

6. Function Buttons

7. Power & System Activity LED
Indicators

8. Speakers

1

2

5

4

6

3

7

88

5

67



Multi Touch Screen

Note that Model B computers incorporate a
touch screen, Model A computers do not.

1 - 8 Tilting the LCD Screen

Quick Start Guide

1

Tilting the LCD Screen

It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc.

1. Place one hand at the top of the computer , and use the other to open the stand to an angle of around
15 degrees from the vertical position (the stand will allow you to adjust to the appropriate angle if you pull it

out and let it spring back).

Figure 1 - 4 - Adjust the Stand

1

2



Moving the Computer

We strongly recommend using both hands to move
the computer. You can use one hand to grip the
computer by the stand, and the other to hold the top
of the LCD screen.

It is recommended that you carry the computer with
the LCD facing your body to avoid scratching the
surface against other objects. However take care not
to scratch the LCD with any personal items, belt fit­tings or jewelry etc.(one hand gripping the stand and
the other gripping the top of the computer to avoid
accidentally dropping it).

15°

Adjust the stand to tilt
the computer to 15°
from the vertical posi­tion.

1

2

Quick Start Guide

Tilting the LCD Screen 1 - 9

1

2. Apply pressure with one hand at the to p (at point ) of the computer (while holding on to the side with the ot her
hand) to carefully push the LCD screen down in order to tilt it to the appropriate viewing angle (up to 50
degrees from the vertical position).

3. Use one hand at the top of the co mputer (while holding on to the side with the other hand) to move the compu ter
back to the original position.

Figure 1 - 5 - LCD Screen Tilt

3

3

Apply pressure from the top of the
screen to adjust the stand outwards
(up to 50° from the vertical position).



DVD Operation

Note that although the comput­er may be tilted up to an angle
of 50 degrees from the vertical
position, the DVD-ROM drive
will only work (i.e continue to
spin and read DVDs) up until an
angle of around 35 degrees
from the vertical position.

If you have any problems with
the system reading DVDs, ad­just the tilt angle accordingly.

50°

50°

Quick Start Guide

1 - 10 Buttons & LED Indicators (Win 8)

1

Buttons & LED Indicators (Win 8)

The buttons located under the front panel icons allow
you to make screen and input adjustments (see page D

- 3 for Windows 7 information).

Figure 1 - 6 - Front Icons

Table 1 - 1 - Function Buttons

The LED indicators on the computer display helpful
information about the current status of the computer.

Table 1 - 2 - LED Indicators

Icon Description

Decrease/Increase Buttons - Use the buttons

to decrease/increase the brightness

Menu Toggle - Use this button to bring up the

on screen menu when HDMI devices are

plugged in

Mode Toggle - Use this button to toggle

between the computer and HDMI Input

modes (see “Mode Toggle” on page 1 - 12)

Icon Color Description

Orange AC/DC Power is Plugged In

Green The Computer is On

Blinking Green The Computer is in Sleep Mode

Orange The Battery is Charging

Blinking Orange

The Battery has Reached

Critically Low Power Status

Blank The Battery is Fully Charged

Green

HDMI Cable Plugged-In (if the

computer is off - see page 1 - 12

Green System Activity

Green

The (optional) WLAN Module is

Powered On

Orange

Win 7 - The (optional) Bluetooth

Module is Powered On

Win 8 - The (optional) Bluetooth

Module is Installed (this is not a

power on/off indicator in

Windows 8)

System Map: Left View 1 - 11

Quick Start Guide

1

System Map: Left View

Figure 1 - 7

Left View

1. Stand

2. Multi-in-1 Card
Reader

3. ExpressCard Slot
(see page 2 - 7)

4. 2 * USB 3.0 Ports

5. HDMI-in Port

6. HDMI-Out Port



ExpressCard Slot

The ExpressCard Slot
accepts either Express-

Card/34 or Express­Card/54 formats.

1



HDMI-In Port

Note that the HDMI-In Port supports video and
audio signals from attached HDMI devices.

Multi-in-1 Card Reader

The card reader allows you to use the most

popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

Compatible

MS (Memory Stick) / MS Pro / MS Duo

USB 3.0 Port

The USB 3.0 port is denoted by its blue color;
USB 2.0 ports are colored black. Note that the
USB 3.0 ports require a driver for Windows 7
(see ““USB 3.0 (Win 7 Only)” on page D - 20)
installation (Windows 8 does not require a driv­er installation) and do not support wake on
USB.

2

3

4

5

6

4

1 - 12 HDMI-In Port

Quick Start Guide

1

HDMI-In Port

This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display
external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen.

The computer itself does not need to be powered on to display video and audio from external HDMI input
sources. As long as the computer is plugged-in to a power source using the AC/DC adapter (the HDMI-In port
will not function under battery power), simply plug-in the HDMI cable from the external device to the com-

puter’s HDMI-In port and the computer will act as the display device. For resolutions supported see page C - 3.

Mode Toggle

Press and hold the mode toggle button to switch between the computer and HDMI input modes. When the
HDMI input source is displayed you can use any HDMI device plugged in to the computer’s HDMI-In port. A
quick press of the button will toggle the display on/off.

When the HDMI cable is plugged-in, and the computer is powered off, the battery/HDMI icon will
be green when you press and hold the mode toggle button . When the HDMI device is playing the icon will
then return to indicate the battery charge status. See Table 1 - 3, on page 1 - 14 for details.

HDMI-In Port 1 - 13

Quick Start Guide

1

Menu Button

Press and hold the menu button when an HDMI device is connected to the HDMI-In port to bring up the on
screen menu. This menu allows you to adjust the Luminance, Color, Volume, On Screen Display and interface
Language. Use the decrease/increase buttons to move up and down the menus, use the menu button to
select an item and use the decrease/increase buttons to make adjustments.

Figure 1 - 8 - Main Menu (If HDMI Device is Connected)



HDMI Cable Removal in

Hibernate or Sleep Modes

Note that (as part of the power saving
feature) if the computer is in Sleep or
Hibernate modes, and the HDMI ca­ble is removed from the HDMI-In port,
any settings adjusted in the Main
Menu will revert to the default settings
when the HDMI cable is plugged-in
again.

It is recommended that you shut the
computer down by choosing the Shut
Down (see page 1 - 5 or D - 2) com-
mand in Windows before removing
the HDMI cable.

1 - 14 HDMI-In Port

Quick Start Guide

1

The following table indicates the standard functions when an HDMI cable is plugged in to the HDMI-In
port (and the computer is powered on/off). See overleaf for information if the computer is in Hibernate or
Sleep modes.

Table 1 - 3 - Mode Toggle Functions when HDMI Cable is Plugged-In (Computer Off/On)

Note that if no HDMI cable is plugged-in to the HDMI-In port, and the system is off, or in Hibernate mode, then
only the power button will function.

Computer Power

Status

Battery/HDMI Icon

Mode Toggle Button

(Press & Hold)

Mode Toggle Button

(Quick Press)

The computer is

powered on (using the

AC/DC adapter)

Indicates battery charge status

only

Toggles between computer

display and HDMI input

Toggles the display on/off

The computer is

powered off (but is

plugged in to the AC/DC

adapter)

Green (when HDMI cable is

plugged-in and the Mode Toggle

Button has been pressed and

held to select HDMI input)

When the HDMI source is playing

the icon will indicate battery

charge status only

Toggles between computer

display and HDMI input

Toggles the display on/off

HDMI-In Port 1 - 15

Quick Start Guide

1

HDMI-In Port in Sleep or Hibernate Modes

Note that if the computer is in Sleep or Hibernate modes, and n o HDMI cable is plugged-in, then the procedure
for plugging-in the HDMI cable and using the system as a display device is as follows:

1. The System is in Sleep or Hibernate mode and no HDMI cable is plugged-in.

2. The battery/HDMI icon will be off.

3. Plug-in the HDMI cable.

4. The battery/HDMI icon will turn green for about 8 seconds and then turn off again.

5. Press the Mode Toggle Button .

6. The battery/HDMI icon will turn green again.

7. After a few seconds the system will display the image from the external HDMI source.

1 - 16 System Map: Right View

Quick Start Guide

1

System Map: Right View

4

2

3

1

2
3

4

4

5



CD/DVD Emergency Eject

If you need to manually eject a
CD/DVD (e.g. due to an unex­pected power interruption) you
may push the end of a straight­ened paper clip into the emer­gency eject hole. Do not use a
sharpened pencil or similar ob­ject that may break and become
lodged in the hole.

Figure 1 - 9 - Right View

1. Optical Device Drive Bay
(for CD/DVD Device - see
page 2 - 3

2. Headphone-Out Jack

3. Microphone-In Jack

4. USB 2.0 Port

5. Stand



Changing DVD Regional Codes

Go to the Control Panel and double-click
Device Manager (Hardware and Sound),
then click the + next to DVD/CD-ROM
drives. Double-click on the DVD-ROM de-

vice to bring up the Properties dialog box,
and select the DVD Region (tab) to bring up
the control panel to allow you to adjust the
regional code. You can select your module’s
region code 5 times (see “DVD Region

Note” on page 2 - 5).



Media Warning

Don’t try to remove the CD/DVD while the
system is accessing it. This may cause the
system to “crash”.

System Map: Rear View 1 - 17

Quick Start Guide

1

System Map: Rear View

Figure 1 - 10

Rear View

1. Rear Component
Cover

2. Stand

3. Vent/Fan Intake

4. Carrying Handle
Area

5. USB Wireless
Transceiver Cover
(for an RF
Keyboard & Mouse
Kit USB Dongle -

not supplied with
this model)

6. Security Lock Slot

7. Battery

8. 2 * RS-232 Serial
Ports

9. PS/2 Port (keyboard)

10.PS/2 Port (mouse)

11.DC-In Jack

12.2 * USB Ports

13.RJ-45 LAN Port

1

2

3

8

3

8

9

4

13

5

5

5

12



USB Port for

Wireless

Transceiver

Note that the USB port
for the wireless trans­ceiver is designed spe­cifically for a USB
dongle for an RF Key­board & Mouse kit (not

supplied with this
model).

Do not use any other
USB devices in this
port.

6

11

7

10

1 - 18 Wireless Keyboard & Mouse USB Transceiver

Quick Start Guide

1

Wireless Keyboard & Mouse USB Transceiver

If you have purchased a wireless keyboard & mouse kit (not supplied with this com­puter) you can use the USB port located at the bottom left of the rear cover to house

the USB transceiver dongle (do not use this port for any other device, see sidebar).

1.Remove the USB transceiver port cover by sliding it in the direction of a rrow .

2.Insert the USB transceiver into the USB port.

3.Replace the cover.



USB Port for

Wireless

Transceiver

Note that the USB port
for the wireless trans­ceiver is designed spe­cifically for a USB
dongle for an RF Key­board & Mouse kit (not

supplied with this
model).

Do not use any other
USB devices in this port.

Figure 1 - 11

USB Port for

Wireless Keyboard

& Mouse Kit

123

1

2

1

3

Windows 8 Touch Screen Controls/Gestures 1 - 19

Quick Start Guide

1

Windows 8 Touch Screen Controls/Gestures

Model B computers incorporate a Touch Screen and this can be used to navigate through he interface in much
the same way as a mouse, touchpad and keyboard. The following gestures are useful when navigating the Win-
dows 8 interface.

• Swipe from the right (Access the Charms Bar) - Pull your finger from the right side of the screen (in the
black area) to the left a little bit to bring up the Charms Bar.

Figure 1 - 12 - Swipe from Right & Left

• Swipe from the left (Switch apps) - If multiple apps are running you can slide your finger from the left side
of the screen (in the black area) to the right to switch between apps.

• Swipe slowly from the left (Snap apps) - Perform the same action above more slowly, to drag one app out
and display it side-by-side with the app that was already on your screen.

1 - 20 Windows 8 Touch Screen Controls/Gestures

Quick Start Guide

1

• Swipe from lef t and back (Display running apps) - Slide your finger fr om the left and quickly drag it back
towards the right to display a list of apps that are currently running. Tap any app to switch to it.

• Pull down from the top (Close app) - Close any running app by starting at the top area of the screen and
quickly pulling your finger about halfway down the screen.

• Swipe down/up (All Apps menu) - Swiping the finger a little bit down from the top, or up from the bottom
of the Start scr een will bring up the menu with the All Apps icon. Tap the All Apps icon to access the apps.

Figure 1 - 13 - Swipe Up and Tap, Hold & Release (Desktop Right-Click)

• Swipe down on an item (Select/right-click) - Swipe down on any tile in the Start screen to select it and
bring up additional options.

• Tap, Hold & Release (Desktop right-click) - Tap the Desktop, hold until a square icon appears, and then
release to access the right click menu.

Touch Keyboard 1 - 21

Quick Start Guide

1

Touch Keyboard

If you need to type on screen then the Touch Keyboard will pop up when required (e.g. when you need to type
in an internet URL address in Internet Explorer). When the Touch Keyboard is displayed you have several dis­play/input options and these can be accessed from the icon at the bottom right of the keyboard.
To access the Touch Keyboard from the Desktop app click/tap the keyboard icon in the taskbar .

Figure 1 - 14 - Touch Keyboard

Touch Keyboard Desktop app taskbar Icon

Select Keyboard or Writing Pad Input

1 - 22 Touch Keyboard

Quick Start Guide

1

The Touch Keyboard allows you to input text without the use of an actual keyboard., and you can use writing
pad to write (continuously or one character at a time) or touch keyboard to input text. Use the Help menu for
further information.

Figure 1 - 15 - Touch Keyboard, Writing Pad Input & Help

Click Help

Windows Control Panel 1 - 23

Quick Start Guide

1

Windows Control Panel

Most of the control panels, utilities and applications within Windows are accessed from the Start menu in Win­dows 7 (Windows 7’s standard interface is the desktop - see page D - 5), and from the Desktop in Windows 8

(see page 1 - 30 for more information on the Windows 8 Control Panel).
Throughout this manual you will see an instruction to open the Control Panel. In Windows 8

right-click the

lower left hot corner to bring up the context menu (or use the Windows Logo Key + X k ey combination)
and select Control Panel. If you are using a Touch Screen then access the Charms Bar from the desktop
(not the Start screen), tap Settings, and tap Control Panel or access it from the All Apps menu.

Figure 1 - 16 - Windows 8 Context Menu & Charms Bar Settings (from Desktop App)

Move the mouse to the

and right-click to access

bottom left of the screen

the menu.

Swipe a finger from the right to access the Charms Bar

and tap Control Panel.

from the Desktop (not the Start Screen), tap Settings

1 - 24 Windows 8 Start Screen & Desktop

Quick Start Guide

1

Windows 8 Start Screen & Desktop

The Apps, control panels, utilities and programs within Windows 8 are accessed from the Metro user interface’s
Start screen and/or Windows Desktop. The Desktop (which runs as an app within the Start screen) can be ac-

cessed by clicking/tapping the Desktop item in the Start screen (or by using the Windows Logo Key + D
key combination).

Figure 1 - 17 - Windows Start Screen

Desktop App

Windows 8 Start Screen & Desktop 1 - 25

Quick Start Guide

1

Apps & Tiles

The Windows 8 Start screen will contain a number of apps, and many more will be installed as you add more
applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of
the screen in order to view all the necessary Apps.

Accessing Pining/Unpinning All Apps

You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area
of the Metro UI Start screen, or swipe a finger from the top or bottom of the touch screen, and you will see

the All Apps icon. Click/tap the All Apps icon to display all the installed applications etc. Right-click any icon,
or swipe down on it, to bring up the menu at the bottom of the screen. You can then click/tap the appropriate
icon to pin the App to (or unpin from) the Start screen, or to the taskbar in the Desktop application.

Figure 1 - 18 - All Apps

Right-click (or swipe down on) an icon
to display the menu

Start Screen and click All Apps (or swipe

Right-click on a blank area of the

a finger up or down on to the screen)

1 - 26 Windows 8 Start Screen & Desktop

Quick Start Guide

1

Desktop Application

When the Desktop app is running (click/tap the app in the Start screen or use the Windows Logo Key + D
key combination), and you are using a keyboard, you can use lower left hot corner to switch between the Start
screen and the Windows Desktop. To do so move you r mouse to hover over the bottom left corner of th e screen
and click/tap the pop-up.

To switch between the Desktop app and Start screen using the touch screen, use the Charms Bar (swipe a
finger from the right and tap Start) to access the Start screen, and tap the Desktop app to switch back.

When you move to the lower left hot corner in the Start screen itself it will take you back to your most recently
used app.

Figure 1 - 19 - Desktop

Move the mouse to the bottom left of the screen and click/tap to switch
back to the Start screen.

Windows 8 Start Screen & Desktop 1 - 27

Quick Start Guide

1

When the Desktop app is running you can right-click (keyboard only) the lower left
hot corner (or use the Windows Logo Key + X key combination) to bring up an
advanced context menu of useful features such as Control Panel, Programs and Fea­tures, Power Options, Task Manager, Search, Windows Explorer, Command Prompt,
Device Manager and Network Connections etc.

Figure 1 - 20 - Advanced Context Menu (Right-Click lower left hot corner)



Display Most

Recently Used

Apps

If you are in the Start
screen, Desktop or an
app you can move your
mouse to the upper left
corner of the screen to
get back to the most re­cently used app.

To view all the most re­cently used Apps hover
over the top left of the
screen and then move
the mouse down along
the left side of the
screen to display the
list.

Move the mouse to the bottom left of the screen

and right-click to access the menu.

1 - 28 Windows 8 Start Screen & Desktop

Quick Start Guide

1

Windows 8 Charms Bar

The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share,
Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right

corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black
when it is active), or use the Windows Logo Key + C key combination (swipe a finger from the right to
access the Charms Bar using the touch screen - see over).

Figure 1 - 21 - Start Screen with Charms Bar

Move the mouse over a Charms Bar icon to activate the menu

Move the mouse to the top/lower right icons to activate the Charms Bar

Move the mouse to the top/lower right icons to activate the Charms Bar

Windows 8 Start Screen & Desktop 1 - 29

Quick Start Guide

1

Charms Bar Items

• Search : You can search for any file, application, Apps and control panel settings with instantaneous
results.

•Share : This button is used to share information with people via mail or social networks.

•Start : Click/tap to bring up the Start Menu (the same function as pressing the Windows Logo Key or

clicking the bottom left of the screen).

• Devices : Click/tap this button to change connected peripheral device settings e.g. an external display.

• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifica­tions, Power and Keyboard (click/tap Change PC Settings to activate the PC Settings menu).

Figure 1 - 22 - Settings Menu



Charms Bar - Touch Screen Access

To quick access the Charms Bar using the Touch Screen:

1. Place your finger off the Touch Screen (slightly to the right of
the screen resting on the black area around the computer
screen).

2. Move your finger across to the left on to the Touch Screen.

3. The Charms Bar will then pop-up.

1 - 30 Windows 8 Control Panel

Quick Start Guide

1

Windows 8 Control Panel

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is much the same as that in Windows 7, however it can be accessed in a number of ways in Windows 8.

• Click/tap Search in the Windows Charms Bar (see previous page) and the search pane will pop out.

Type Control Panel and select it from the results to the left.

Figure 1 - 23 - Search (Control Panel)

• Click/tap on Computer (you may need to pin Computer to the Start screen) in the Start screen, click/
tap on Computer in the top menu and select Open Control Panel from the ribbon.

Figure 1 - 24 - Open Control Panel (Computer)

Windows 8 Control Panel 1 - 31

Quick Start Guide

1

• When in the Desktop app (this does not apply to the Start screen) click/tap on Settings in the Windows
Charms Bar and select Control Panel from the menu.

Figure 1 - 25 - Settings Charms Bar (Desktop App Only)

• Right-click on a blank area of the Metro UI Start screen, or swipe a finger from the top or bottom of
the touch screen. Click/tap the All Apps icon and click/tap Control Panel.

Figure 1 - 26 - All Apps - Control Panel

1 - 32 Windows 8 Control Panel

Quick Start Guide

1

• Right-c lick the lower left hot corner to br ing up the menu and select Control Panel (see Figure 1 - 20 on

page 1 - 27).



Keyboard Shortcut to Control Panel

You can also use keyboard shortcuts to access the Contro l Pa nel. Press the W indows logo key and X to bring up
the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R
to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.

Windows 8 Control Panel 1 - 33

Quick Start Guide

1

Windows 8 Taskbar

In many instances throughout this manual you will see an instruction to access the notification area of the task­bar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will

need to click/tap the Desktop app to switch to the Desktop.

The taskbar is displayed in much the same way as it was in Windows 7, and you can see the notification area of
the taskbar in the bottom right of the screen. Some of the Control Panels and applications referred to during the
course of this manual can be accessed from here.

Figure 1 - 27 - Desktop Taskbar

You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Accessing

Pining/Unpinning All Apps” on page 1 - 25).

1 - 34 Video Features

Quick Start Guide

1

Video Features

You can switch display devices, and configure display options, from the Display control panel (in Appearances
and Personalization) in Windows 8 in the same manner as Windows 7 running the Desktop app (see “Desktop

Application” on page 1 - 26 and Appendix B). In Windows 8 it is possible to quickly configure external displays

from the Devices menu item in the Charms Bar (see “Windows 8 Charms Bar” on page 1 - 28).

To Configure Displays from Devices (Charms Bar):

1. Attach your display to the HDMI-Out port, and turn it on.

2. Go the Charms Bar and select Devices.

3. Click/tap Second Screen.

4. Click/tap on any one of the options from the menu to select Duplicate, Extend or a Single display.

Figure 1 - 28 - Second Screen (Devices)

Video Features 1 - 35

Quick Start Guide

1

To access Display (Control Panel) and Screen Resolution in Windows 8:

1. Go to the Control Panel.

2. Click/tap Display (ic on) - In the Appearance and Personalization category.

3. Adjust resolution.

Figure 1 - 29 - Screen Resolution

1

3

2



Right-Click Desktop App

1. You can right-click (tap
and the touch screen
until you see a square
icon and then release
your finger) the desktop
and select Screen reso-
lution (Figure 1 - 29).

2. Use the dropbox to select
the screen Resolution

(Figure 1 - 29).

3. Click Advanced
settings (Figure 1 -

29) to bring up the

Advanced properties
tabs.

123

1 - 36 Video Features

Quick Start Guide

1

To access the Intel(R) Graphics Media Accelerator Driver for mobile control panel:

1. Click/tap Advanced settings (Figure 1 - 29 on page 1 - 35) in the Screen Resolution control panel in
Windows.

2. Click/tap the Intel(R)... tab and click/tap Graphics Properties (button) (Figure 1 - 30 on page 1 - 36) .

OR

3. Right-click (tap, hold and release) the desktop and select Graphics Properties from the menu.

OR

4. Click/tap the icon in the notification area of the Desktop taskbar and select Graphics Properties from the
menu.

Figure 1 - 30 - Intel GMA Driver for Mobile Control Panel

3

4

4

Power Options 1 - 37

Quick Start Guide

1

Power Options

Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set-
tings in the Charms Bar in Windows 8 may be used to Shut down or Restart (you can also add Hibernate/
Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9).

Shut Down, Restart or Sleep

1. Go to the Charms Bar and click/tap Settings.

2. Click/tap Power .

3. Select Sleep, Shut Down or Restart.

Figure 1 - 31 - Power (Settings)

1 - 38 Running Metro UI Apps

Quick Start Guide

1

Running Metro UI Apps

To run apps in the Metro UI in Windows 8 you will need to check that the Screen Resolution and User Account
Control Settings are compatible with the system requirements.

Screen Resolution Settings

1. Switch to the Windows Desktop (click/tap the app or use the Windows logo key + D key combination).

2. Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to
make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).

Figure 1 - 32 - Screen Resolution



Screen Resolution for Metro Style Apps

(Windows 8)

The minimum resolution in which Metro style Apps will run is 1024x768.
The minimum resolution required to support all the features of Windows

8 (including multitasking with snap) is 1366x768.
These specs are the minimum screen resolution that supports all the

features of Windows 8 on a useful physical size.

Running Metro UI Apps 1 - 39

Quick Start Guide

1

User Account Control Settings

If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then
that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC
is turned off. To check whether the UAC is on or off, follow the instructions below.

1. Open the Control Panel.

2. Click/tap on User Accounts and then clic k/tap on Change User Account Control settings (or click/tap
System and Security and click/tap Change User Account Control Settings under Action Center).

3. If the slider is in the Never notify position, then the UAC is disabled.

4. To enable or turn on the UAC, move the slider to Always no tify or Notify me when app s t ry to make changes
to my computer (default) position, and then click/tap OK.

Figure 1 - 33 - User Account Control

Quick Start Guide

1 - 40

1

Features & Components

Overview 2 - 1

2

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components
of the computer:

•Hard Disk Drive

• Optical (CD/DVD) Device

• Multi-in-1 Card Reader

• ExpressCard Slot

• Audio Features

• Keyboard Shortcuts - Windows 8

Features & Components

2 - 2 Hard Disk Drive

2

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be
taken out to accommodate other 2.5" or 3.5" (pictured below) serial (SATA) hard
disk drives with a height of 9.5 mm.

The hard disk is accessible from the rear of your computer as seen below. For further
details see “Upgrading the Hard Disk Drive/SSD” on page 6 - 9.



Power Safety

Before attempting to ac­cess any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the ma­chine is turned off. Also
ensure that all peripher­al cables, including
phone lines, are discon­nected from the comput­er.

Figure 2 - 1

Hard Disk Location

Hard Disk

Features & Components

Optical (CD/DVD) Device 2 - 3

2

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de­vice will depend on the module you purchased (see “Storage” on page C - 3). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 13).

Loading Discs

To insert a CD/DVD, press the open button and
carefully place a CD/DVD onto the disc tray with la­bel-side facing up (use just enough force for the disc
to click onto the tray’s spindle). Gently push the CD/
DVD tray in until its lock “clicks” and you are ready
to start. The busy indicator will light up while
data is being accessed, or while an audio/video CD,
or DVD, is playing. If power is unexpectedly inter­rupted, insert an object such as a straightened paper
clip into the emergency eject hole to open the
tray.



Volume Adjustment

The sound volume level
can be set using the vol­ume control in the Set-

tings menu in the
Charms Bar (see “Au-

dio Features” on
page 2 - 8).

Figure 2 - 2

Optical Device

1

2

3

123

Features & Components

2 - 4 Optical (CD/DVD) Device

2

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.



CD Emergency Eject

If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharp­ened pencil or similar
object that may break
and become lodged in
the hole.

Disk Eject Warning

Don’t try to remove a
CD/DVD while the sys­tem is accessing it. This
may cause the system
to “crash”.

Features & Components

Optical (CD/DVD) Device 2 - 5

2

DVD Regional Codes

To change the DVD regional codes:

1. Go to the Control Panel

2. Double-click/tap Device Manager (Hardware and Sound), then click/tap the +
next to DVD/CD-ROM drives.

3. Double-click/t ap on the DVD-ROM device to bring up the Properties dialog box,
and select the DVD Region (tab) to bring up the control panel to allow you to
adjust the regional code.



DVD Region Note

DVD region detection is
device dependent, not
OS-dependent. You can
select your module’s re­gion code 5 times. The
fifth selection is perma­nent. This cannot be al­tered even if you change
your operating system
or you use the module in
another computer.

Figure 2 - 3

DVD Region Codes

• Region 1 - USA & Canada

• Region 2 - Western Europe, Japan,

South Africa, Middle East & Egypt

• Region 3 - South-East Asia, Taiwan,

South Korea, The Philippines, Indo­nesia, Hong Kong

• Region 4 - South & Central Amer-

ica, Mexico, Australia, New Zealand

• Region 5 - N Korea, Russia, Eastern

Europe, India & Most of Africa

• Region 6 - China

Features & Components

2 - 6 Multi-in-1 Card Reader

2

Multi-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “ExpressCard/Card Reader” on page 4 - 7).



Card Reader Cover

Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust get­ting in to the card read­er.

Figure 2 - 4

Front View

1. Card Reader

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

1

Features & Components

ExpressCard Slot 2 - 7

2

ExpressCard Slot

The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/
34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC
Cards).

ExpressCard/54 is used for applications which re­quire a larger interface slot, e.g. CompactFlash card
reader. The number denotes the card width; 54mm
for the Express Card/54 and 34mm for the Express­Card/34. Make sure you install the Card Reader driv­er (see “ExpressCard/Card Reader” on page 4 - 7).

Inserting and Removing Express­Cards

• Align the ExpressCard with the slot and push it in

until it locks into place.

• To remove an ExpressCard, simply press the card

to eject it.



ExpressCard Slot

Cover

Make sure you keep the
cover in the Express­Card slot when not in
use. This will help pre­vent foreign objects and/
or dust getting in to the
ExpressCard Slot.

Figure 2 - 5

ExpressCard Slot

1. ExpressCard
Slot

1

Features & Components

2 - 8 Audio Features

2

Audio Features

You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar
notification area/control panel (right-click the taskbar notification area icon to
bring up an audio menu). The volume may also be adjusted by means of the volume
icon in the taskbar or the audio slider in the Settings menu (see sidebar).



Volume Adjustment

The sound volume level
can be set using the vol­ume control in the Set-

tings menu in the
Charms Bar.

Figure 2 - 6

Realtek Audio

Manager

Right-click the icon
to access the menu
above.

Note that many keyboards have built-in controls to allow you to adjust the audio vol­ume.

Features & Components

Audio Features 2 - 9

2

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instruc­tions below:

1. Go to the

Control Panel

.

2. Click/tap Realtek HD Audio Manager (Hardware and Sound), or right-click the
taskbar icon and select Sound Manager.

3. Click/tap Micr ophone Effects (tab) in Microphone (tab), and then click/tap to
select Noise Suppression (button), or adjust the Recording Volume level to
around 60, to obtain the optimum recording quality.

4. Click/tap OK to close the control panel and save the settings.

Figure 2 - 7

Realtek Audio

Manager -

Recording Setup

Features & Components

2 - 10 Keyboard Shortcuts - Windows 8

2

Keyboard Shortcuts - Windows 8

If you are using a keyboard with this system then note the function of the Windows
Logo Key & Menu/Application Key (in the Start screen). The following keyboard

shortcuts are useful for navigation/operation in Windows 8.

Windows Logo Key +

Description

Tap Winkey

Toggle between the Start screen and the foremost

running app or the Windows Desktop
C Display Charms menu
D Switch to the Windows Desktop and toggle show Desktop

E

Switch to the Windows desktop and launch Windows

Explorer with Computer displayed

F Display file Search

I Open the Settings charm
K Open the Connect charm
L Lock the computer and display the Lock screen
P Display the Second Screen menu

R

Switch to the Windows Desktop and display the Run

dialog box

Z Access the App Bar



Windows Logo

Keyboard Shortcut

Use the Windows logo
key + D key combi-
nation to switch be­tween the Start screen
and Windows Desktop.

Menu/Application

Keyboard Shortcut

When the Desktop app
is running you can use
the Menu/Application
key on the keyboard
to display the context
menu as per a mouse
right-click. In the Start
screen this function is
useful to quickly display
the All Apps icon.

Table 2 - 1

Windows 8

Keyboard Shortcuts

Power Management

Overview 3 - 1

3

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system.

This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information
The computer uses enhanced power saving techniques to give the operating system

(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user set­tings and information from applications.

Using some form of power management greatly increases the life span of the
LCD.



OS Note

Power management
functions will vary slight­ly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operat­ing system.

(Note: All pictures used
on the following pages
are from the Windows 8
OS.)

Power Options

Power management in
Windows is configured
from Power Options
(Hardware and
Sound), which can be
accessed from the Con-
trol Panel (see page 1 -

30).

Power Management

3 - 2 The Power Sources

3

The Power Sources

The computer can be powered by either the AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.

1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.

3. Adjust the LCD to a comfortable viewing angle.

4. Press the power button on the front of the computer for about 2 - 3 seconds to
turn the computer “on” (note that the power LED on the front of the computer will
turn from orange to green when the computer powers on).

Battery

The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”

on page 3 - 16).

We recommend that you do not remove the battery. For more information on the bat­tery, please refer to “Battery Information” on page 3 - 12.

Power Management

Turning On the Computer 3 - 3

3

Turning On the Computer

Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options (Hardware and Sound) in the Windows control panel to configure
this feature.

Figure 3 - 1

Power Menu

(Settings - Charms

Bar)



Shut Down

Note that you should always shut your com­puter down by choosing the Shut Down
command from the Power Menu in the Set-
tings menu in the Windows 8 Charms Bar.

This will help prevent hard disk or system
problems. If you want to add Hibernate/
Sleep to the Power Menu

see “Adding Hi-

bernate/Sleep to the Power Menu” on
page 3 - 9.

Power Management

3 - 4 Power Plans

3

Power Plans

The computer can be configured to conserve power by means of power plans. You
can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.

Click/tap Change plan settings and then click/tap Change advanced power settings
to access further configuration options in Advanced Settings.



Resuming

Operation

See Table 3 - 1, on

page 3 - 10 for informa-

tion on how to resume
from a power-saving
state.

Password

It is recommended that
you enable a password
on system resume in or­der to protect your data.

Figure 3 - 2

Power Plan

Advanced Settings

Power Management

Power Plans3-5

3

Each Windows power plan will also adjust the processor performance of your ma­chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click/tap Show additional plans to
view the High performance plan) for maximum performance when the computer is
powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) pow­ered.

Figure 3 - 3

Power Plans

Click/tap to Show/Hide
additional
power plans

Power Management

3 - 6 Power-Saving States

3

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where
you left off. Win 8 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.

If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer do wn before the battery becomes
depleted.

To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power

Menu” on page 3 - 9.



Wake On LAN

Support

(Windows 8)

Wake-On-LAN is only
supported from Sleep or

Hibernate states in
Windows 8.

If you require your com­puter to wake up from
network activity in Win­dows 8 then make sure
that the computer is ei­ther in Sleep or Hiber-
nate.

Wake-On-LAN is not
supported from Shut­down states in Win-
dows 8.

Power Management

Power-Saving States 3 - 7

3

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery. To add Hibernate to the
Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t for­get to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from Shut down takes longer than
from Sleep or Hibernate.

Figure 3 - 4

Power Menu

Power Management

3 - 8 Configuring the Power Buttons

3

Configuring the Power Buttons

The power button may be set to send the computer in to either Sleep or Hibernate.
In Sleep, the LED will blink green. In Hibernate the LED will be orange. If
only the display is turned off, the LED will remain green. Click/tap Choose what
the power buttons do on the left menu in Power Options to bring up the menu.



Password

Protection

It is recommended that
you enable a password
on wake up in order to
protect your data.

However you can dis­able this setting from the
Power Options menu
by clicking Require a

password on wakeup

in the left menu, and se­lecting the options (click/
tap Change settings

that are currently un­available).

Figure 3 - 5

Power Options

Define Power

Buttons

Power Management

Configuring the Power Buttons 3 - 9

3

Adding Hibernate/Sleep to the Power Menu

Add Hibernate/Sleep to the Power Menu as follows.

1. Go to the Power Options (Hardware and Sound) control panel (see page 1 - 30).

2. Click/tap Choose what the power buttons do.

3. Click/tap to put a tick in the Hibernate/Sleep box under Shutdown settings.

4. Click/tap Save Changes and close the control panel.

Figure 3 - 6

Power Options

Define Power

Buttons - Shutdown

Settings

Power Management

3 - 10 Configuring the Power Buttons

3

Resuming Operation

You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (see your keyboard documentation).

Power Status

Icon Color

To Resume

Power Off Off Press the Power Button

Sleep Blinking Green

Press the Power Button

Press the Sleep Button

(see your keyboard documentation)

Hibernate

Off (battery)

Press the Power Button

Orange (AC/DC adapter)

Display Turned Off Green Press a Key or Move the Mouse

Table 3 - 1

Resuming

Operation



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down
hot key button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down).

Power Management

Configuring the Power Buttons 3 - 11

3

Ctrl + Alt + Delete Key Combination

You can use the CTRL + ALT + DEL key combination from almost any of the Win­dows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log

off, Change a password and Task Manager options. If you click/tap the Power
icon in the lower right corner of the screen a power management option menu ap­pears to display Sleep, Shut down, and Restart.

To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to per­form the function selected.

Figure 3 - 7

Ctrl + Alt + Delete

Menu

Power Management

3 - 12 Battery Information

3

Battery Information

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Change plan settings > Change advanced power settings (see Figure

3 - 2 on page 3 - 4).

Click/tap the battery icon in the notification area to see the current battery level
and charge status.



Low Battery

Warning

When the battery is criti­cally low, immediately
connect the AC/DC
adapter to the computer
or save your work, oth­erwise, the unsaved
data will be lost when
the power is depleted.

Figure 3 - 8

Battery Icon

(Notification Area) &

Battery Advanced

Settings

Power Management

Battery Information 3 - 13

3

Conserving Battery Power

•Use a power plan that conserves power (e.g Power saver), however note that

this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or communication applications when they are
not being used.

• Disconnect/remove any unnecessary external devices e.g. USB devices.



Windows Mobility

Center

The Windows Mobility
Center (Hardware and
Sound) control panel

provides an easy point
of access for information
on battery status, power
plans used and wireless
device status etc.

Figure 3 - 9

Windows Mobility

Center

Power Management

3 - 14 Battery Information

3

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason (e.g. long term storage) see “Removing the Battery”

on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 16 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “Buttons &

LED Indicators (Win 8)” on page 1 - 10 for information on the battery charge sta-

tus, and to “Battery FAQ” on page 3 - 16 for more information on how to maintain
and properly recharge the battery pack.)

Power Management

Battery Information 3 - 15

3

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances.

• DO NOT expose the battery to fire or high temperatures, it may explode.

• DO NOT connect the metal terminals (+, -) to each other.



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your distributor/supplier. If the battery has been dropped we
do not recommend using it any further, as even if the comp uter continues to work with a
damaged battery in place, it may cause circuit damage, which may possibly result in fire. It
is recommended that you replace your computer battery every two years.



Caution

Danger of explosion if
battery is incorrectly re­placed.

Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s in­structions.

Power Management

3 - 16 Battery Information

3

Battery FAQ

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.

1. Save and close all files and applications.

2. Create a power plan for discharging the battery and set all the options to Never.

Figure 3 - 10

Power Plan Create

Power Management

Battery Information 3 - 17

3

3. Click/tap Change plan settings (after creating it) and click/tap Change plan

settings > Change advanced power settings.

Figure 3 - 11

Change Plan

Settings / Change

Advanced Power

Settings

Power Management

3 - 18 Battery Information

3

4. Scroll down to Battery and click/tap + to expand the battery options.

5. Choose the options below (click/tap Yes if a warning appears):

• Low battery levels = 0%

• Critical battery Levels = 1%

• Low battery action = Do Nothing

• Critical battery action (On battery) = Shut Down

• Critical battery action (Plugged in) = Do Nothing

Figure 3 - 12

Power Options

Advanced Settings -

Battery

Power Management

Battery Information 3 - 19

3

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.

Power Management

3-20

3

Drivers & Utilities

What to Install 4 - 1

4

Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utilities essential to the operation or
improvement of some of the computer’s subsystems. The system takes advantage of
some newer hardware components for which the latest versions of most available op­erating systems haven’t built in drivers and utilities. Thus, some of the system com­ponents won’t be auto-configured with an appropriate driver or utility during
operating system installation. Instead, you need to manually install some system-re­quired drivers and utilities.

For information on the Windows 7 operating system see Appendix D.

What to Install

The Device Drivers & Utilities + Use r’s Manual disc contains the drivers and util-
ities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 4
lists what you need to install and it is very important that the drivers are installed

in the order indicated (all drivers provided are for Windows 8 & Windows 7 with
Service Pack 1).

The procedures for installing drivers for the PC Camera, Wireless LAN and Blue­tooth & WLAN Combo modules are provided in “Modules & Options” on page 7

- 1.



Driver Installation &

Power

When installing driv­ers make sure your
computer is powered
by the AC/DC adapter
connected to a work­ing power source.

Some drivers draw a
significant amount of
power during the instal­lation procedure, and if
the remaining battery
capacity is not adequate
this may cause the sys­tem to shut down and
cause system problems
(note that there is no
safety issue involved
here, and the battery will
be rechargeable within 1
minute).

Drivers & Utilities

4 - 2 What to Install

4

Driver Installation (Windows 8)

1. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive.

2. Click/tap the message “Tap to choose what happens with this disc.”

3. Click/tap Run autorun.exe.

Figure 4 - 1 - Autorun Driver Installation Disc

4. Click/tap Install Drivers (button), or Option Drivers (button) to access the Optional driver menu.

5. Check the driver installa tion order from T able 4 - 1, on page 4 - 4 (the drivers must be installed in this order)

which is the same as that listed in the Drivers Installer menu below.

6. Click/tap to select the driver you wish to install, (you should note down the drivers as you install them).

7. Follow the instructions for each individual driver installation procedure as listed on the appropriate pages.



Driver Installation

If you miss the message above you can eject the De­vice Drivers & Utilities + User’s Manual disc and then

reinsert it.
Alternatively double-click/tap the disc icon in Com-

puter (use the Windows logo key + E key com­bination to go to Computer in Windows Explorer).