Blue Rhino UniFlame EF700SP Replacement Instructions Manual

REPLACEMENT INSTRUCTIONS

(Environmentally Friendly Sugar

Indoor Electric Fireplace

Replacing the Glass and Logs

Model No. EF700SP

WARNING

FOR YOUR SAFETY:

For Indoor Use Only

WARNING

FOR YOUR SAFETY:

1. Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage.

2. Read the installation, operation, and
maintenance instructions thoroughly before
installing or servicing this equipment.

3. Failure to follow these instructions could
result in fire or explosion, which could cause
property damage, personal injury or death.

4. This instruction manual contains important
information necessary for the proper
assembly and safe use of the appliance.

5. Read and follow all warnings and
instructions before assembling and using
the appliance.

6. Follow all warnings and instructions when
using the appliance.

Danger

Do NOT use electric fireplace for cooking.
NOT to be used in or on boats or recreational
vehicles.

Table of Contents

Important Safeguards ...........................................Page 2

Replacement Instructions ............................................ 3

Operating Instructions............................................... 6

Before Turning “ON” ............................................ 6

Turning “ON”................................................... 6

While Electric fireplace is “ON” ..................................... 6

Using Remote Control ............................................ 6

Turning “OFF” .................................................. 6

The use and installation of this product must conform to local codes.

Save these instructions for future reference. If you are assembling this unit for
someone else, give this manual to him or her to read and save for future reference.

WARNING

FOR YOUR SAFETY:

1. Installation and repair should be done by a qualified service
person.

2. Use only Blue Rhino Global Sourcing, Inc. factory authorized parts. The use

of any part that is not factory authorized can be dangerous. This will also
void your warranty. Contact 1.800.762.1142.

3. Do not use flammable solutions or material to clean electric heater or

electric fireplace parts. Use only warm soapy water to clean outside of
electric fireplace.

4. Do not submerge any part of electric fireplace in water.

Made from 75% Bagasse

Cane Pulp By-product)

Manufactured in China for: Blue Rhino Global Sourcing, Inc

Winston-Salem, NC USA • 1.800.762.1142, www.bluerhino.com

© Blue Rhino Global Sourcing, Inc. All Rights Reserved

UniFlame

®

is a Registered Trademark of Blue Rhino Global Sourcing, Inc.. All Rights Reserved. EF700SPRGL-IS-101

Intdoor Electric Fireplace Model No. EF700SP

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always
be followed including the following:

1. Read all instructions before using this electric fireplace.

2. Do not touch hot surfaces.

3. T his electric fireplace is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. Keep combustible material such as electrical
cords, furniture, papers, clothes, and curtains at least 3 feet (0.9 M)
away from the front of the electric fireplace and away from the sides
and rear.

4. To protect against electrical shock do not immerse cord, plugs, or

heating element in water or other liquids.

5. Close supervision is necessary when any appliance is used by or near

children.

6. Unplug from outlet when not in use and before cleaning. Allow to cool

before cleaning.

7. Do not operate any electric fireplace with a damaged cord or plug or

after the electric fireplace malfunctions, has been dropped or has been
damaged in any manner. Return appliance to the nearest authorized
service facility for examination, repair, or adjustment.

8. This electric fireplace is not intended for commercial use.

9. The use of accessory attachments not recommended by the appliance
manufacturer may cause injuries.

10. Do not let cord touch hot surfaces.

11. Do not place on or near a hot gas or electric burner, or in a heated

oven.

13. Do not use appliance for other than intended use.

14. Use only on properly grounded outlet.

15. Do not run cord under carpeting. Do not cover cord with throw rugs,

runners, or similar coverings. Arrange cord away from traffic area and
where it will not be tripped over.

16. Do not insert or allow foreign objects to enter any ventilartion or

exhause opening as this may cause an electric shock or fire, or
damage the electric fireplace.

15. SAVE THESE INSTRUCTIONS.

DANGER: Failure to follow the dangers, warning and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion

causing damage to property.

WARNING:

This electric fireplace is hot when in use. To avoid burns, do not let bare

skin touch hot surfaces.
This electric fireplace is for indoor use only.
For residential use only. This electric fireplace is NOT for commercial

use.
This electric fireplace is for use with electricity.
This electric fireplace is safety certified for use in the United States and/

or Canada only. Do not modify for use in any other location. Modification

will result in a safety hazard.
Always unplug the electric fireplace if it is not being used.
Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.
Avoid the use of an extension cord because the extension cord may

overheat and cause a risk of fire.
Do not use 16 gauge extension cords. Damage to household wiring and/

or fire could result.
Longer detachable power-supply cords or extension cords are available

and may be used if care is exercised in their use.
If a longer detachable power-supply cord or extension cord is used,

a. The cord shall be no. 14 AWG minimum size and rated not less than

2,000 watts.

b. The marked electrical rating of the cord set or extension cord should

be at least as great as the electrical rating of the appliance, and

c. The cord should be arranged so that it will not drape over the

countertop or tabletop where it can be pulled on by children or
tripped over unintentionally.

ELECTRIC SHOCK CAN KILL OR RESULT IN SERIOUS INJURY. TO PREVENT

ELECTRICAL SHOCK:

a. Use only with GFI (Ground Fault Interrupter) protected circuit.
b. To prevent electric fireplace from being splashed or falling into

water, do not use electric fireplace within 10 feet (3.05 m) of sinks or

bathtubs.
c. Keep electric fireplace and cord dry and out of rain at all times.
d. Do not operate electric fireplace that has a damaged cord, plug, or

metal probe. Call our customer service for a replacement cord. This

cord is made specifically for this electric fireplace.
e. Never remove grounding plug, or use with an adapter to two prongs.
f. Keep electric plugs off ground, and dry.
g. In case of fire, turn electric fireplace “OFF”, unplug electric fireplace

from outlet, and allow fire to burn out. Do not use water to put out a

fire in this or another electrical appliance.
h. Do not use water or other liquid spray to clean electric fireplace

without first unplugging electric cord.
i. Do NOT place the electric fireplace near a bed because objects such

as pillows or blankets can fall off the bed and be ignited by the
electric fireplace.

j. To prevent a possible fire, do not block air intakes or exhause in any

manner. Do not use on soft surfaces, like a bed, where opening may
befcome blocked.

If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a
hazard.

The use of alcohol, prescription or non-prescription drugs may impair

the consumer’s ability to properly assemble or safely operate the
appliance.

Never use charcoal, lighter fluid, lava rocks, gasoline, kerosene or

alcohol with this product.

Do not store or use gasoline or other flammable liquids or vapors within

25 feet (7.62 m) of this appliance.

A electric fireplace has hot and arcing or sparking parts inside. Do not

use in an explosive atmosphere. Keep electric fireplace area clear and
free from combustible materials, gasoline and other flammable vapors

and liquids.
DO NOT burn wood or other materials in this fireplace.
DO NOT use this electric fireplace near any unprotected combustible

constructions.
Do not alter this electric fireplace in any manner.
Do not use the electric fireplace unless it is COMPLETELY assembled and

all parts are securely fastened and tightened.
DO NOT strike fireplace glass.
This electric fireplace should be thoroughly inspected on a regular basis.
Do not build this model of electric fireplace in any built-in or slide in

construction. Ignoring this warning could cause a fire or an explosion

that can damage property and cause serious bodily injury or death.
Use only Blue Rhino Global Sourcing, Inc. factory authorized parts. The

use of any part that is not factory authorized can be dangerous. This will

also void your warranty.
Do not use this appliance without reading “Operating Instructions” in

this manual.
Do not touch metal parts of electric fireplace until it has completely

cooled (about 45 min.) to avoid burns, unless you are wearing protective

gear (pot holders, gloves, BBQ mittens, etc.).
Do not use in or on boats or recreational vehicles.
Do not leave a lit electric fireplace unattended, especially keep children

and pets away from electric fireplace at all times.
Do not attempt to move electric fireplace when in use. Allow the electric

fireplace to cool before moving or storing.
Keep all electrical cords away from a hot electric fireplace.
Always use on a level surface.
After a period of storage and/or nonuse, inspect for any abrasion, wear,

cuts to the electrical cord.
The use of accessory attachments not recommended by the appliance

manufacturer may cause injuries.
Servicing should be done only while the electric fireplace is disconnected

from the power supply.
To ensure continued protection against electrical shock, connect only to

properly grounded outlets.
Do not immerse in water. Disconnect electric cord from outlet before

cleaning, servicing and/or removing heating element. To reduce the risk

of electric shock, use with GFI protected electric outlet only.
High temperatures may be generated under certain abnormal conditions.

Do not partially or fully cover or obstruct this electric fireplace.
Please use protective gloves when assembling this product.
Do not force parts together as this can result in personal injury or

damage to the product.
Use this electric fireplace only as descibed in this manual. Any other use

not recommended by the manufacturer may cause fire, electrical shock,

or injury to persons.
Use protective gloves when assembling this product.
Do not force parts together as this can result in personal injury or

damage to the product.
Deaths, serious injury or damage to property may occur if the above is

not followed exactly.

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

Replacement Instructions

page no.

3

1

DO NOT RETURN PRODUCT TO STORE.

For assistance call 1.800.762.1142 toll free. Please have
your owner’s manual and serial number available for
reference.

For Easiest Assembly:

• To avoid losing any small components or hardware,
assemble your product on a hard level surface that does
not have cracks or openings.

• Clear an area large enough to layout all components and
hardware.

• When applicable, tighten all hardware connections by
hand first. Once the step is completed, go back and fully
tighten all hardware.

• Follow all steps in order to properly assemble your
product.

2

Turn Off and Unplug

1. Push the main power switch to the “OFF” position.

2. Unplug the power cord from the wall outlet.

3

Note: Two people are required to move the electric
replace.

Unscrew Firebox

Remove Firebox

4

Replacement Instructions (continued)

Intdoor Electric Fireplace Model No. EF700SP

5

Remove Front Heat Panel Insert

Remove Front Heat Panel

6

7

Remove Top Glass Frame Support

Remove Decorative Glass Inserts

8

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

Replacement Instructions (continued)

page no.

5

9

Remove Glass Panels.

If you are replacing the glass only,

10

please follow the steps in reverse, then
go to the Operating Instructions section.

If you are replacing the logs, please
continue.

Remove Front Door Panel Supports

11

Remove Decorative Front Panel

12

Replacement Instructions (continued)

Intdoor Electric Fireplace Model No. EF700SP

Remove Glass Frame

13

Unscrew Firebox

14

Reassemble Fireplace

Follow the instructions in reverse to assemble your electric

15

fireplace.

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

OFF

ON

Main Power and Flame Operation Instructions

1. Plug the power cord into a dry 120V grounded outlet.

2. The main power ( ) must be ON for the heater to
work. Push the main power switch ( ) so the switch
is in the ON position

3. Adjust the heater control knob ( ) to your desired
setting.

OFF

ON

OFF

ON

Main Power and Flame Operation Instructions

1. Plug the power cord into a dry 120V grounded outlet.

2. The main power ( ) must be ON for the heater to
work. Push the main power switch ( ) so the switch
is in the ON position

3. Adjust the heater control knob ( ) to your desired
setting.

Metal Screw

OFF

ON

Main Power and Flame Operation Instructions

1. Plug the power cord into a dry 120V grounded outlet.

2. The main power ( ) must be ON for the heater to
work. Push the main power switch ( ) so the switch
is in the ON position

3. Adjust the heater control knob ( ) to your desired
setting.

page no.

7

Operating Instructions

Do NOT use an extension cord because

the extension cord may overheat and
cause a risk of fire.

Before Turning “ON”

1. Make sure all packaging and protective films have
been removed from the electric fireplace.

2. Electric fireplace should be thoroughly inspected
before each use, and by a qualified service person at
least annually.

Turning “ON”

Caution: Keep electric fireplace area

clear and free from combustible
materials, gasoline and other flammable
vapors and liquids.

Caution: Do not obstruct the flow of

ventilation air.

1. Make sure the main power switch ( ) is in the
“OFF” position. (Illustration 1)

Product size

Illustration 1

Operating Instructions

Note: When the main power is turned on the fire log
brightness is factory set to medium brightness.

4. To adjust the flame level, press one of the flame button

):

(

“+” means more brightness

“–” means less brightness.

5. To turn heat level “ON” / “OFF”, press the heat button

) .

(
Note: the button will turn the heat “ON” to the level set
by the heat level control knob.

6. Push the power button (

Note: This does not turn the entire electric fireplace

“OFF”, the electric fireplace is in the “standby mode”.

Turning “OFF”

1. Push the main power switch ( ) to the “OFF”
position.

2. Unplug the power cord from the wall outlet.

) to turn “OFF”.

Illustration 5

Infrared remote.

2. Plug the power cord into a dry 120V GFI (Ground Fault
Interrupter) 3 plug outlet. (Illustration 2)

3. Push the main power switch to the “ON” position.
(Illustration 1).

4. Adjust flame control knob (

) to the desired setting.

Note: If you do not want the flame, turn the flame control
knob to the twelve (12) o’clock position.

5. To turn the heat on, push the heat switch (

) to the

“ON” position.

6. Adjust the heat control knob (

) to the desired

setting.

Note: If you do not want the heat, push the heat switch
to the “OFF” position.

Note: Fire log brightness can only be controlled by using
the remote. There are not separate controls for the fire
log brightness on the control panel.

Note: When the main power is turned on the fire log
brightness is factory set to medium brightness.

Main Power and ame control.

Illustration 2

Using Remote Control

Note: Once the remote is used, the control panel knobs
are disabled.

Note: To enable the control panel knobs push the main

power switch (
position, wait 5 seconds, then push the main power
switch to the “ON” position.

Note: The effective range of the remote control is up to

19.7 ft. (6 m).

1. Insert 2 AAA batteries (NOT INCLUDED) into the back
of the remote.

Note: Do NOT mix old and new batteries.

Note: Do NOT mix alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadium) batteries.

2. If the electric fireplace is unplugged:

a. Make sure the main power switch (

“OFF” position. (Illustration 1)

b. Plug the power cord into a dry 120V GFI (Ground

Fault Interrupter) 3 plug outlet. (Illustration 2)

c. Push the main power switch to the “ON” position.

(Illustration 3).

) on the control panel to the “OFF”

) is in the

Connecting the power cord to a

dry GFI 3 plug outlet.

Illustration 3

Main Power and ame control.

Illustration 4

If the electric fireplace is plugged into a dry GFI outlet.

a. Push the main power switch to the “ON” position.

(Illustration 3).

3. To adjust the fire log brightness, press one of the log

button (

“+” means more brightness

“–” means less brightness.

Note: Fire log brightness can only be controlled by using
the remote. There are not separate controls for the fire

):

log brightness on the control panel.

Heat power and heat control.