Blue Rhino FC-0007 User Manual

Page 1

SE6

ROTARY MOWER

Published 05/05 Effective Serial No. SE6-33916 through Current Part NO. 00768614C

OPERATOR’S MANUAL

This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, and Operation Instructions contained in this manual before operating the equipment. C01-

Cover

UNDERSTAND, and FOLLOW the Safety

RHINO®

1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com

$0.00

Page 2

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain

Page 3

In order to reduce accidents and enhance the safe operation of mowers, Alamo Group Ag Division, in cooperation with other industry manufacturers has developed the AEM/FEMA Industrial and Agricultural Mower Safety Practices video and guide book.

The video will familiarize and instruct mower-tractor operators in safe practices when using industrial and agricultural mowing equipment. It is important that Every Mower Operator be educated in the operation of their mowing equipment and be able to recognize the potential hazards that can occur while operating a mower. This video, along with the mower operator’s manual and the warning messages on the mower, will significantly assist in this important education.

Your Authorized Alamo Ag Dealer may have shown this video and presented you a DVD Video when you purchased your mower. If you or any mower operator have not seen this video, Watch the Video, Read this Operator’s Manual, and Complete the Video Guidebook before operating your new mower. If you do not understand any of the instructions included in the video or operator’s manual or if you have any questions concerning safety of operation, contact your supervisor, dealer or Alamo Group Ag.

If you would like a VHS video tape of the video, please email AEMVideo@alamo-group.com or Fax AEM VHS Video at (830) 372-9529 or mail in a completed copy of the form on the back of this page to AEM VHS Video 1502 E Walnut Street, Seguin, TX 78155. and request the VHS video version. Please include your name, mailing address, mower model and serial number.

Every operator should be trained for each piece of equipment (Tractor and Mower), understand the intended use, and the potential hazards before operating the equipment.

Page 4

Alamo Group Ag. Division is willing to provide

one (1) AEM Mower Safety Practices Video

Please Send Me: VHS Format – AEM/FEMA Mower Operator Safety Video

DVD Format – AEM/FEMA Mower Operator Safety Video

Mower Operator’s Manual

AEM Mower Operator’s Safety Manual

Requester Name Phone:

Requester Address:

City

State

Zip Code

Mower Model: Serial Number:

Date Purchased: Dealer Salesperson:

Dealership Name: Dealership Location:

Mail to:

AEM Video Services

1502 E Walnut street

Seguin, TX 78155

Or Fax to:

(830) 372-9529

Or Email to:

AEMVideo@alamo-group.com

Page 5

SAFETY SECTION ......................................................................................... 1-1

General Safety Instructions and Practices ......................................................................................................... 1-2

Operator Safety Instructions and Practices ....................................................................................................... 1-3

Equipment Operation Safety Instructions and Practices .................................................................................... 1-5

Connecting or Disconnecting Implement Safety Instructions and Practices .................................................... 1-11

Transporting Safety Instructions and Practices ............................................................................................... 1-12

Maintenance and Service Safety Instructions and Practices ........................................................................... 1-14

Storage and Parking Safety Instructions and Practices ...................................................................................1-16

Concluding Safety Instructions and Practices .................................................................................................. 1-16

Decal Location ................................................................................................................................................. 1-17

Decal Description ............................................................................................................................................. 1-21

Federal Laws and Regulations ........................................................................................................................ 1-26

INTRODUCTION SECTION ............................................................................ 2-1

Attention Owner/Operator .................................................................................................................................. 2-4

ASSEMBLY SECTION.................................................................................... 3-1

DEALER SETUP INSTRUCTIONS .................................................................................................................... 3-2

SHIELD ASSEMBLY (Figure AsmP-R-0016) ..................................................................................................... 3-2

A-FRAME INSTALLATION (FIGURE Asm-R-0075). .........................................................................................3-3

TAIL WHEEL INSTALLATION (FIGURE Asm-R-0076). ....................................................................................3-4

TONGUE ASSEMBLY PULL-TYPE MOWER (FIGURE Asm-R-0077) ............................................................ 3-5

TAILWHEEL- ASSEMBLY PULL-TYPE MOWER (FIGURE Asm-R-0078) ....................................................... 3-6

SHEAR BOLT or SLIP CLUTCH DRIVELINE INSTALLATION ........................................................................ 3-7

Front and Rear Deflectors (Standard Equipment) ............................................................................................ 3-8

CHAIN GUARDS (Optional Equipment at extra cost) (Figures Asm-R-0081 & Asm-R-0082) ..........................3-9

CHECK CHAINS (Extra Equipment) - FIGURE Asm-R-0083 .......................................................................... 3-10

OFFSET ADAPTER HITCH (EXTRA EQUIPMENT) (Figure Asm-R-0084) ...................................................3-11

OPERATION SECTION .................................................................................. 4-1

Standard Equipment and Specifications ............................................................................................................ 4-3

OPERATOR REQUIREMENTS ......................................................................................................................... 4-4

TRACTOR REQUIREMENTS ............................................................................................................................ 4-5

ROPS and SEAT BELT .....................................................................................................................................4-5

Tractor Safety Devices .......................................................................................................................................4-6

Tractor Horsepower ...........................................................................................................................................4-6

3-Point Hitch ...................................................................................................................................................... 4-6

Front End Weight ............................................................................................................................................... 4-7

Drawbar-Pull Type Mower ................................................................................................................................. 4-7

Power Take Off (PTO) ....................................................................................................................................... 4-8

GETTING ON AND OFF THE TRACTOR ......................................................................................................... 4-8

Boarding the Tractor .......................................................................................................................................... 4-9

Dismounting the Tractor ..................................................................................................................................... 4-9

Page 6

STARTING THE TRACTOR ............................................................................................................................ 4-10

CONNECTING THE MOWER TO THE TRACTOR ......................................................................................... 4-10

Connecting the Mower-Lift Type ...................................................................................................................... 4-11

Connecting the Mower-Pull Type ..................................................................................................................... 4-12

Safety Chains ................................................................................................................................................... 4-12

SETTING THE MOWER .................................................................................................................................. 4-13

Setting Mower Height- Lift Type ....................................................................................................................... 4-13

Setting Mowing Height-Lift Type ...................................................................................................................... 4-14

Setting Deck Pitch ............................................................................................................................................ 4-15

DRIVELINE ATTACHMENT ............................................................................................................................4-15

Driveline Length Check .................................................................................................................................... 4-16

PRE-OPERATION INSPECTION AND SERVICE ...........................................................................................4-17

Tractor Pre-Operation Inspection/Service ........................................................................................................ 4-18

Mower Pre-Operation Inspection/Service ........................................................................................................ 4-18

Cutting Component Inspection ......................................................................................................................... 4-22

DRIVING THE TRACTOR AND IMPLEMENT .................................................................................................4-23

Starting the Tractor .......................................................................................................................................... 4-24

Brake and Differential Lock Setting .................................................................................................................. 4-24

Raising the Mower ........................................................................................................................................... 4-25

Driving the Tractor and Mower ......................................................................................................................... 4-25

Crossing Ditches and Steep Inclines ...............................................................................................................4-26

OPERATING THE TRACTOR AND IMPLEMENT ........................................................................................... 4-27

Foreign Debris Hazards ................................................................................................................................... 4-28

Bystanders/Passersby Precautions .................................................................................................................4-28

Engaging the Power Take Off (PTO) ............................................................................................................... 4-29

PTO RPM and Ground Speed ......................................................................................................................... 4-30

Operating the Mower ....................................................................................................................................... 4-30

Shutting Down the Implement .......................................................................................................................... 4-33

DISCONNECTING THE MOWER FROM THE TRACTOR ............................................................................. 4-34

MOWER STORAGE ........................................................................................................................................ 4-36

TRANSPORTING THE TRACTOR AND IMPLEMENT ...................................................................................4-36

Transporting on Public Roadways ................................................................................................................... 4-37

Hauling the Tractor and Implement .................................................................................................................. 4-39

TROUBLESHOOTING GUIDE ........................................................................................................................ 4-41

MAINTENANCE SECTION ............................................................................. 5-1

Lubrication ......................................................................................................................................................... 5-2

GEARBOX ......................................................................................................................................................... 5-3

DRIVELINE LUBRICATION ............................................................................................................................... 5-4

BLADE SERVICING .......................................................................................................................................... 5-5

BLADE SHARPENING ......................................................................................................................................5-6

BLADE CARRIER REMOVAL/INSTALLATION ................................................................................................. 5-6

BLADE CARRIER REMOVAL ...........................................................................................................................5-7

BLADE CARRIER INSTALLATION ...................................................................................................................5-7

BLADE REMOVAL .............................................................................................................................................5-7

SLIP CLUTCH .................................................................................................................................................... 5-8

SEASONAL CLUTCH MAINTENANCE .............................................................................................................5-9

MOWER STORAGE ....................................................................................................................................... 5-10

TORQUE CHART ............................................................................................................................................ 5-10

GEARBOX SERVICING .................................................................................................................................. 5-11

GEARBOX DISASSEMBLY (Figure Mnt-R-0083) ........................................................................................... 5-12

INPUT SHAFT DISASSEMBLY AND ASSEMBLY (Figure Mnt-R-0084) ......................................................... 5-13

GEARBOX INPUT SHAFT REAR BEARING ................................................................................................... 5-15

Page 7

SAFETY SECTION

Safety Section 1-1

Page 8

SAFETY

General Safety Instructions and Practices

A safe and careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety Messages before assembling, operating or servicing this Implement. This equipment should only be operated by those persons who have read the Manual, who are responsible and trained, and who know how to do so safely and responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this manual and on decals which are attached to the equipment. The Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word are intended to warn the owner/ operator of impending hazards and the degree of possible injury faced when operating this equipment.

SAFETY

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards.

Practice all usual and customary safe working precautions and above all---remember safety is up to YOU

. Only YOU can prevent serious injury or death from unsafe practices.

The lowest level of Safety Message; warns of possible injury. Decals located on the Equipment with this Signal Word are Black and Yellow

Serious injury or possible death! Decals are Black and Orange.

Imminent death/critical injury. Decals are Red and White.

(SG-1)

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad.

SE6 05/05 Safety Section 1-2

(SG-3)

Page 9

SAFETY

til

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

(SG-30)

Operator Safety Instructions and Practices

The rotating parts of this machine continue to rotate even after the PTO has been turned off. The operator should remain in his seat for 60 seconds after the brake has been set, the PTO disengaged, the tractor turned off, and all evidence of rotation has ceased.

“Wait a minute...Save a life!”

Never crawl under a raised Implement supported solely by the Tractor 3-Point hitch. Release of the control lever or mechanical failure will result in the Implement falling and possible injury or death. Always securely block up the Implement before crawling underneath to perform repairs and service.

(S3PT-19)

(S3PT-10)

SAFETY

ever operate the Tractor or Implement un

you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency. Never allow inexperienced or untrained personnel too operate the Tractor and Implement without supervision. Make sure the operator has fully read and understood the manuals prior to operation.

(SG-4)

The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items thrown by the equipment.

(SG-16)

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS! Tractors with or without an Implement attached can often be noisy enough to cause permanent hearing loss. We recommend that you always wear hearing protection if the noise in the Operator’s position exceeds 80db. Noise over 85db over an extended period of time will cause severe hearing loss. Noise over 90db adjacent to the Operator over an extended period of time will cause permanent or total hearing loss. NOTE: Hearing loss

from loud noise [from tractors, chain saws, radios, and other such sources close to the ear] is cumulative over a lifetime without hope of natural recovery.

(SG-I7)

SE6 05/05 Safety Section 1-3

Page 10

SAFETY

ith th

Prol

tti

SAFETY

ways read carefully and comply fully w

handling oil, solvents, cleansers, and any other chemical agent.

e manufacturers instructions when

(SG-22)

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement and possible serious injury or death.

(SG-24)

Never allow children to play on or around Tractor or Implement. Children can slip or fall off the Equipment and be injured or killed. Children can cause the Implement to shift or fall crushing themselves or others.

(SG-25)

NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability to operate the equipment safely. Before operating the Tractor or Implement, an operator on prescription or over-the-counter medication must consult a medical professional regarding any side effects of the medication that would hinder their ability to operate the Equipment safely. NEVER knowingly allow anyone to operate this equipment when their alertness or coordination is impaired.

Serious injury or death to the

operator or others could result if the operator is under the influence of drugs or alcohol.

(SG-27)

onged operation may cause operator boredom and fatigue affecting safe operation. Take scheduled work breaks to help prevent these potentially impaired operating conditions. Never operate the Implement and Tractor in a fatigued or bored mental state which impairs proper and safe operation.

se extreme caution when ge

(SG-32)

ng onto the Implement to perform repairs, maintenance and when removing accumulated material. Only stand on solid flat surfaces to ensure good footing. Use a ladder or raised stand to access high spots which cannot be reached from gound level. Slipping and falling can cause serious injury or death.

Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and hose connections. Relieve hydraulic pressure before performing maintenance or repairs. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding.

(SG-34)

SE6 05/05 Safety Section 1-4

(SG-33)

Page 11

SAFETY

g g

ldi

DO NOT operate this Implement on a Tractor that is not properly maintained. Should a mechanical or Tractor control failure occur while operating, immediately shut down the Tractor and perform repairs before resuming operation. Serious injury and possible death could occur from not maintaining this Implement and Tractor in good operating condition.

Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding.

(SG-38)

(SG-36)

Do not put hands or feet under mower decks. Blade Contact can result serious injury or even death. Stay away until all motion has stopped and the decks are securely blocked up.

(SGM-9)

Always keep a careful lookout and use extreme care when working around utility and municipal obstructions. Never allow the Mower to contact any utility, municipal, or other type structure. Clearly mark all mowing obstructions and consult local utility providers for a safe code of operation.

(SPU-5)

Do not operate the implement while wearing loose fitting clothing. Entanglement of the clothin with the rotating elements can result in serious injury or even death. Stay clear of all rotatin elements at all times. (SSP-3)

Equipment Operation Safety Instructions and Practices

Never leave the Tractor and Implement unattended while the Implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing. To properly park the implement when disconnecting it from the tractor, lower the stand and put the retaining pin securely in place, or put a secure support under the AFrame. Lower the implement carefully to the ground. Do not put hands or feet under lifted components.

(S3PT-1)

SAFETY

se extreme care when lowering or unfo

ng the implement’s wings. Make sure no bystanders are close by or underneath the wings. Allow ample clearance around the implement when folding or unfolding the wings. Use extreme caution around buildings or overhead power lines.

SE6 05/05 Safety Section 1-5

(S3PT-5)

Page 12

SAFETY

ill b

This Implement is wider than the Tractor. Be careful when operating or transporting this equipment to prevent the Implement from running into or striking sign posts, guard rails, concrete abutments or other solid objects. Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control, serious injury, or even death. Never allow the Implement to contact obstacles.

(S3PT-12)

SAFETY

e sure you have adequate knowledge of the property you w

e working on. Take time to make yourself aware of any area underground lines or cables. Contact with buried lines or cable could result in serious injury or death.

(SBH-6)

Do not operate Mower if excessive vibration exists. Shut down PTO and the Tractor engine. Inspect the Mower to determine the source of the vibration. If Mower blades are missing or damaged replace them immediately. Do not operate the mower until the blades have been

replaced and the Mower operates smoothly. Operating the Mower with excessive vibration can result in component failure and broken objects to be thrown outward at very high velocities. To reduce the possibility of property damage, serious injury, or even death, never allow the Mower to be operated with blades missing.

(SFL-4)

Operate this Equipment only with a Tractor equipped with an approved rollover-protective system (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS.

(SG-7)

BEFORE leaving the tractor seat, always engage the brake and/or set the tractor transmission in parking gear, disengage the PTO, stop the engine, remove the key, and wait for all moving parts to stop. Place the tractor shift lever into a low range or parking gear to prevent the tractor from rolling. Never dismount a Tractor that is moving or while the engine is running. Operate the Tractor controls from the tractor seat only.

(SG-9)

Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death.

SE6 05/05 Safety Section 1-6

(SG-10)

Page 13

SAFETY

Never allow children to operate, ride on, or come close to the Tractor or Implement. Usually, 16-17 year-old children who are mature and responsible can operate the implement with adult supervision, if they have read and understand the Operator’s Manuals, been trained in safe operation of the tractor and Implement, and are physically large enough to reach and operate the controls easily.

Do not mount the Tractor while the tractor is moving. Mount the Tractor only when the Tractor and all moving parts are completely stopped.

Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operators manual for proper starting instructions.

(SG-11)

(SG-12)

(SG-13)

SAFETY

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil and fuel are expensive and their presence could present a hazard. Do not check for leaks with your hand! High-pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene. To check for a hose leak, SHUT the tractor ENGINE OFF and remove all hydraulic pressure. Wear oil impenetrable gloves, safety glasses and use Cardboard to check for evidence of oil leaks. If you suspect a leak, REMOVE the HOSE and have it tested at a Dealer. If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure.

(SG-15)

Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health.

(SG-23)

Do not exceed the rated PTO speed for the Implement. Excessive PTO speeds can cause Implement driveline or blade failures resulting in serious injury or death.

(SG-26)

Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat with the seat belt securely fastened around you. Inadvertent movement of the Tractor or Implement may cause serious injury or death.

(SG-29)

SE6 05/05 Safety Section 1-7

Page 14

SAFETY

difficulty duri

iti

Ext

SAFETY

n case of mechincal

ng operation, place the transmission in the park pos

on, se the parking brake, shut down all power, including the PTO and the engine and remove the key. Wait until all rotating motion has stop before dismounting. (SG-39)

Do Not operate this equipment in areas where insects such as bees may attack you and/or cause you to lose control of the equipment. If you must enter in such areas, use a tractor with an enclosed Cab and close the windows to prevent insects from entering. If a tractor cab is not available, wear suitable clothing including head, face, and hand protection to shield you from the

insects. Attacking insects can cause you to lose control of the tractor, which can result in serious injury or death to you or bystanders. Never dismount a movingtractor.

(SG-40)

Mow only in conditions where you have clear visibility in daylight or with adequate artificial lighting. Never mow in darkness or foggy conditions where you cannot clearly see at least 100 yards in front and to the sides of the tractor and mower. Make sure that you can clearly see and identify passersby, steep slopes, ditches, drop-offs, overhead obstructions, power lines, debris and

foreign objects. If you are unable to clearly see these type of items discontinue mowing.

(SGM-1)

There are obvious and hidden potential hazards in the operation of this Mower. REMEMBER! This machine is often operated in heavy brush and in heavy weeds. The Blades of this Mower can throw objects if shields are not properly installed and maintained. Serious injury or even death may occur unless care is taken to insure the safety of the operator, bystanders, or passersby in the area. Do not operate this machine with anyone in the immediate area. Stop mowing if anyone is within 100 yards of mower.

(SGM-2)

The rotating parts of this machine have been designed and tested for rugged use. However, the blades could fail upon impact with heavy, solid objects such as metal guard rails and concrete structures. Such impact could cause the broken objects to be thrown outward at very high velocities. To reduce the possibility of property damage, serious injury, or even death, never allow the cutting blades to contact such obstacles.

reme care should be taken when operating near loose objects such as gravel, rocks, wire, and other debris. Inspect the area before mowing. Foreign objects should be removed from the site to prevent machine damage and/or bodily injury or even death. Any objects that cannot be removed must

be clearly marked and carefully avoided by the operator. Stop mowing immediately if blades strike a foreign object. Repair all damage and make certain rotor or blade carrier is balanced before resuming mowing.

SE6 05/05 Safety Section 1-8

(SGM-4)

(SGM-5)

Page 15

SAFETY

The M

ifi

any varied objects, such as wire, cable, rope, or chains, can become entangled in the operating parts of the mower head. These items could then swing outside the housing at greater velocities than the blades. Such a situation is extremely hazardous and could result in serious injury or even death. Inspect the cutting area for such objects before mowing. Remove any like object

from the site. Never allow the cutting blades to contact such items.

ow at the speed that you can safely operate and control the tractor and mower. Safe mowing

speed depends on terrain condition and grass type, density, and height of cut. Normal ground speed range is from 0 to 5 mph. Use slow mowing speeds when operating on or near steep slopes, ditches, drop-offs, overhead obstructions, power lines, or when debris and foreign objects

are to be avoided.

(SGM-7)

Avoid mowing in reverse direction when possible. Check to make sure there are no persons behind the mower and use extreme care when mowing in reverse. Mow only at a slow ground speed where you can safely operate and control the tractor and mower. Never mow an area that you have not inspected and removed debris or foreign material.

Do not mow with two machines in the same area except with Cab tractors with the windows closed.

(SGM-11)

(SGM-6)

(SGM-8)

SAFETY

Follow these guidelines to reduce the risk of equipment and grass fires while operating, servicing, and repairing the Mower and Tractor:

-Equip the Tractor with a fire extinguisher in an accesible location.

-Do Not operate the Mower on a Tractor with an underframe exhaust.

-Do Not smoke or have an open flame near the Mower and Tractor.

-Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes. Periodically shut down the Tractor and Mower and clean clippings and collected debris from the mower deck.

ower is designed for certain mowing applications and is rated to cut up to a spec

(SGM-12)

c size vegetation (see Mower Standard Equipment and Specifications). DO NOT use this mower to cut vegetation above the Mower’s rated capacity or to cut any type of non-vegetative material. Only operate this Mower on a properly sized and equipped Tractor. Operating this Mower in an

application for which it is not designed and/or operating the Mower with the wrong size Tractor can cause Mower component damage and equipment failure resulting in possible serious injury or death.

(SGM-14)

SE6 05/05 Safety Section 1-9

Page 16

SAFETY

Do not operator or pull the mower into standing water. When uplift or fan type mower blades contact water they can be severely deflected downward causing possible failure of blade resulting in serious boldly injury to the operator or bystanders.

Use extreme caution when raising the Mower above ground level. Stop the Blades from turning when the Mower is raised and passersby are within 100 yards. Raising the Mower exposes the Cutting Blades which creates a potentially serious hazard and can cause serious injury by objects thrown from the Blades or by contact with the Blades.

(SGM-15)

(SPU-1)

SAFETY

Rotary Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully.

STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS:

-Front and Rear Deflectors, Chain Guards, or Bands are installed and in good, workable condition;

-Mower sections or Wings are running close to and parallel to the ground without exposed Blades;

-Passersby are outside the existing thrown-object zone;

-All areas have been thoroughly inspected and all foreign material such as rocks, cans, glass, and general debris has been removed.

NOTE: Where there are grass and weeds high enough to hide debris that could be struck by the blades, the area should be: inspected and large debris removed, mowed at an intermediate height, inspected, closely with any remaining debris being removed, and mowed again at desired final height. (This will also reduce power required to mow, reduce wear and tear on the Mower drivetrain, spread cut material better, eliminate streaking, and make the final cut more uniform).

(SRM-1)

Do Not attempt to raise or lower the implement wing unless the Implement tongue is securely attached to

the Tractor drawbar. The Implement could tip over and cause equipment damage and possible serious

injury or death. Raise or Lower the mower wing only while seated in the Tractor operator’s seat with the

seat belt securely fastened.

SE6 05/05 Safety Section 1-10

(SRM-2)

Page 17

SAFETY

PTO, it is i

Do not turn so sharp or lift mower so high to produce a severe "knocking" of the Driveline which will cause accelerated wear and breakage of drive train components and could result in possible injury from the separated Driveline sections.

Do not let the Blades turn when the Mower Deck is raised for any reason, including clearance or for turning. Raising the Mower deck exposes the Cutting Blades which creates a potentially serious hazard and could cause serious injury or even death from objects thrown from the Blades.

Connecting or Disconnecting Implement Safety Instructions and Practices

DO NOT use a PTO adapter to attach a non-matching Implement driveline to a Tractor PTO. Use

of an adapter can double the operating speed of the Mower resulting in excessive vibration, thrown objects, and blade and mower failure. Adapter use will also change the working length of

the driveline exposing unshielded driveline areas. Serious bodily injury and/or equipment failure can result from using a PTO adapter. Consult an authorized dealer for assistance if the Implement driveline does not match the Tractor PTO.

(SRM-4)

(SRM-7)

(S3PT-14)

SAFETY

Always shut the Tractor completely down, place the transmission in park, and set the parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches.

(S3PT-15)

Never operate the Tractor and Mower if the Implement input driveline is directly connected to the Tractor transmission. Tractor braking distances can be substantially increased by the momentum of the rotating Mower blades driving the Tractor transmission even though the Tractor clutch has been disengaged. Install an over running clutch between the Tractor PTO and the Mower

driveline to prevent this potentially dangerous situation.

en attaching the Implement input driveline to the Tractor

(S3PT-16)

mportant that the connecting yoke spring activated locking collar slides freely and the locking balls are seated securely in the groove on the Tractor PTO shaft. A driveline not attached correctly to the Tractor PTO shaft could come loose and result in personal injury and damage to the Implement.

(S3PT-17)

Before operating the Implement, check to make sure the Implement input driveline will not bottom out or become disengaged. Bottoming out occurs when the inner shaft penetrates the outer housing until the assembly becomes solid-it can shorten no more. Bottoming out can cause

serious damage to the Tractor PTO by pushing the PTO into the Tractor and through the support bearings or downward onto the PTO shaft, breaking it off. A broken drive line can cause personal injury.

(S3PT-18)

SE6 05/05 Safety Section 1-11

Page 18

SAFETY

t t

Transporting Safety Instructions and Practices

Be particularly careful when transporting the Implement with the Tractor. Turn curves or go up hills

only at a low speed and using a gradual steering angle. Rear mounted implements move the center of gravity to the rear and remove weight from the front wheels. Make certain, by adding front ballast, that at least 20% of the tractor’s weight is on the front wheels to prevent rearing up, loss of steering control or Tractor tip-over. Slow down on rough or uneven surfaces to preven loss of steering control which could result in property damage or possible injury. Do not transpor unless 3-Point lift lever is fully raised and in the latched transport position. Dropping implement in transport can cause serious damage to the tractor and/or Implement and possibly cause the

SAFETY

operator or others to be injured or killed.

Allow sufficient clearance for the Implement to swing outward while turning. Implements carried behind the Tractor will swing outside the tire path when making turns. Contacting a solid object while turning will cause equipment damage and possible injury.

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations.

(S3PT-2)

(S3PT-20)

(SG-6)

SE6 05/05 Safety Section 1-12

Page 19

SAFETY

Only t

Transport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the safe transport speeds for you and the equipment. Make sure you abide by the following rules:

• Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement. As you increase the speed of the Tractor the stopping distance increases. Determine the maximum safe transport speed for you and this Equipment.

• Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that it is safe to operate at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum safe turning speed for you and this equipment before operating on roads or uneven ground.

• Only transport the Tractor and Implement at the speeds that you have determined are safe and which allow you to properly control the equipment.

SAFETY

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy.

(SG-19)

Be particularly careful when transporting the Implement using the tractor. Turn curves or go up or down hills only at a low speed and at a gradual steering angle. Make certain that at least 20% of the tractor’s weight is on the front wheels to maintain safe steerage. Slow down on rough or uneven surfaces.

ow the Implement behind a properly sized and equipped Tractor whic exceeds the weight of the Implement by at least 20%. DO NOT tow the Implement behind a truck or other type of vehicle. Never tow the Implement and another Implement connected in tandem. Never tow the Implement at

speeds over 20 MPH.

(STI-1)

(STI-6)

SE6 05/05 Safety Section 1-13

Page 20

SAFETY

ith fact

librati

dif

this Impl

dif

this Impl

lifted

Your driving vision may be reduced or impaired by the tractor, cab, or implement. Before driving on public roadways identify any limited vision areas, and make adjustments to your operating position, mirrors, and the implement transport position so that you can clearly see the area where you will be traveling, and any traffic that may approach you. Failure to maintain adequate vision o the public roadway and traffic can result in serious injury or even death. (STI-10)

Maintenance and Service Safety Instructions and Practices

Make sure the PTO shield, integral driveline shields, and input shields are is installed when using PTO-driven equipment. Always replace any shield if it is

SAFETY

damaged or missing.

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Implement on the ground or securely blocked up, disengage the PTO, and turn off the tractor engine. Push and pull the Remote Cylinder lever in and out several times prior to starting any maintenance or

repair work.

(S3PT-9)

(S3PT-8)

Always disconnect the main PTO Driveline from the Tractor before performing service on the Implement. Never work on the Implement with the tractor PTO driveline connected and running. Rotating Parts, Blades or Drivelines could turn without warning and cause immediate entanglement, injury or death.

ever interfere w

failure of the equipment and may result in injury.

(S3PT-11)

ory-set hydraulic ca

ons. Any change in ca

(SBH-13)

on could cause a

Always maintain the safety decals in good readable condition. If the decals are missing, damaged, or unreadable, obtain and install replacement decals immediately.

o not mo

any of its components or any Implement function.

ever work under the Implement, the framework, or any

y or alter

ement. Do not permit anyone to mo

(SG-8)

componen

(SG-5)

y or alter

ement,

unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death.

(SG-14)

SE6 05/05 Safety Section 1-14

Page 21

SAFETY

dli

Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is off before working on the Implement.

Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working

order.

Do Not fill gasoline tank while engine is running. Refuel only after engine has cooled down. If gasoline is spilled, move machine away from the area of the spill and avoid creating any source of ignition until the gasoline has evaporated.

(SG-20)

(SG-21)

(SG-28)

SAFETY

Perform service, repairs and lubrication according to the maintenance section. Ensure the unit is properly lubricated as specified in the lubrication schedule and all bolts and nuts are properly torqued. Failure to properly service, repair and maintain this Implement in good operating condition could cause component failure and possible serious injury or even death.

se caution and wear protective gloves when han

ng sharp objects such as blades, knives, an

(SG-35)

other cutting edges. Be alert to worn component surfaces which have sharp edges. Sharp surfaces can inflict severe laceration injuries if proper hand protection is not worn.

(SG-37)

All Safety Shields, Guards and Safety devices including (but not limited to)

- the Deflectors, Chain Guards, Steel Guards, Gearbox Shields, PTO integral shields, and Retractable Door Shields should be used and maintained in good working condition. All safety devices should be inspected carefully at least daily for missing or broken components. Missing, broken, or worn items must be replaced at once to reduce the possibility of injury or death from thrown objects, entanglement, or blade contact.

(SGM-3)

Replace bent or broken blade with new blades. NEVER ATTEMPT TO STRAIGHTEN OR WELD ON BLADES SINCE THIS WILL LIKELY CRACK OR OTHERWISE DAMAGE THE BLADE WITH SUBSEQUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM THROWN BLADES.

(SGM-10)

SE6 05/05 Safety Section 1-15

Page 22

SAFETY

ill b

diti

likelihood of

dditi

this Impl

PARTS INFORMATI O N Rhino mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to Rhino

specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance, void warranties, and present a safety hazard. Use genuine Rhino mower parts for economy and safety.

(SPRM-1)

SEE YOUR RHINO DEALER

SAFETY

e sure you have adequate knowledge of the property you w yourself aware of any area underground lines or cables. Contact with buried lines or cable could result in serious injury or death.

n wet con

that this material is removed before travelling on public roadways.

ons where there is a

(STL-1)

material collecting on the Implement, make certain

e working on. Take time to make

(STL-7)

Storage and Parking Safety Instructions and Practices

To prevent tipping of Implement when stored in folded position, use carrying wheels or adequate stands on center frame.

(S3PT-6)

Concluding Safety Instructions and Practices

In a hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

on to the design and configuration of

ement, including Safety Signs and Safety Equipment,

(SG-18)

SE6 05/05 Safety Section 1-16

Page 23

Decal Location

3 POINT LIFT MOWER

SAFETY

NOTE: Rhino supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in

shipping, use, or reconditioning. Rhino cares about the safety of its customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of charge (Some shipping and handling charges may apply). Contact your Rhino dealer to order replacement decals.

SE6 05/05 Safety Section 1-17

Page 24

SAFETY

ITEM PART NO. QTY TYPE DESCRIPTION

1. 00773723 1 PELIGRO Rotating Driveline Translation

2. 00769736 1 WARNING Use/Repair Shields & Guards

3. 00725746 1 PELIGRO Get Safety Translated

4. 00760657 1 IMPORTANT Genuine Parts, Rhino Rotary

5. 00763977 1 INSTRUCT Notice to Owner

6. 00756494 1 DANGER Driveline Hazards

7. 00769737 1 DANGER Blades-Thrown Objects

8. 00749117 1 DANGER Multiple Hazard

9. D302 2 LOGO Rhino Logo

10. 00763613 1 INSTRUCT Slip Clutch Adjustment

11. D103 1 INSTRUCT 540 RPM

12. D303 2 NAME Rhino Name

13. 0901000010 2 NAME SE5 Name Decal

SAFETY

14. 2738332 2 REFLECT Red Reflector

15. 00756004 ((1)) DANGER Driveline Shield Missing

16. 00756005 ((1)) DANGER Rotating Driveline

17. NFS 1 SRL PLT Serial Plate

18. 00776031 1 Canister, Operators Manual

19. 00768614C 1 Operator’s Manual

20. 10058000 3 Bolt

21. 00017000 3 Lockwasher

22. 00024100 6 Flatwasher

23. 02959924 3 Locknut

(( )) Installed by D/L Manufacturer

SE6 05/05 Safety Section 1-18

Page 25

PULL TYPE MOWER

SAFETY

NOTE: Rhino supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in

SE6 05/05 Safety Section 1-19

Page 26

SAFETY

ITEM PART NO. QTY TYPE DESCRIPTION

1. 00773723 1 PELIGRO Rotating Driveline Translation

2. 00769736 1 WARNING Use/Repair Shields & Guards

3. 00725746 1 PELIGRO Get Safety Translated

4. 00760657 1 IMPORTANT Genuine Parts, Rhino Rotary

5. 00763977 1 INSTRUCT Notice to Owner

6. 00756494 1 DANGER Driveline Hazards

7. 00769737 1 DANGER Blades-Thrown Objects

8. 00749117 1 DANGER Multiple Hazard 8a. 00756059 1 WARNING Hydraulic Oil Leak

9. D302 2 LOGO Rhino Logo

10. 00763613 1 INSTRUCT Slip Clutch Adjustment

11. D103 1 INSTRUCT 540 RPM 11a. D102 1 INSTRUCT PTO Shaft

12. D303 2 NAME Rhino Name

SAFETY

13. 0901000010 2 NAME SE5 Name Decal

14. 2738332 2 REFLECT Red Reflector

15. 00756004 ((1)) DANGER Driveline Shield Missing

16. 00756005 ((1)) DANGER Rotating Driveline

17. NFS 1 SRL PLT Serial Plate

18. 00776031 1 Canister, Operators Manual

19. 00768614C 1 Operator’s Manual

20. 10058000 3 Bolt

21. 00017000 3 Lockwasher

22. 00024100 6 Flatwasher

23. 02959924 3 Locknut

(( )) Installed by D/L Manufacturer

SE6 05/05 Safety Section 1-20

Page 27

SAFETY

Decal Description

PELIGRO! Spanish Translation for Driveline Safety

P/N 00773723

DANGER! Maintain shields and deflectors in good condition. Failure to do so may lead to injury or even death.

SAFETY

P/N 00769736

Peligro Translation, If you do not know how to read English, please find someone who knows how to read English.

P/N 00725746

For safety and to guarantee optimum product reliability always use genuine RHINO replacement parts.

P/N 00760657

SE6 05/05 Safety Section 1-21

Page 28

Operator's Manual (with repair parts) and warranty was attached to this implement during final inspection.

P/N 00763977

DANGER! Make certain that drivelines are correct length and are securely attached.

SAFETY

P/N 00756494

DANGER! Keep Away Thrown Objects.

P/N 00769737

DANGER! Multi-Hazard Decal

(Refer To Front Cover)

P/N 00749117

SE6 05/05 Safety Section 1-22

Page 29

SAFETY

WARNING! Never use your hand to check for oil leaks. Always use paper or cardboard.

P/N 00756059

Logo Product Name: Rhino

P/N D302

Attention! Do not operate until all slip clutches are properly adjust and are not frozen.

SAFETY

P/N 00763613

WARNING! Avoid Bodily Injury, Use 540RPM PTO Speed Only.

P/N D103

SE6 05/05 Safety Section 1-23

Page 30

IMPORTANT! Required For Jackshaft Unit. Suggested for standard shaft.

P/N D102

Logo Product Name: Rhino

SAFETY

P/N D303

SE6 Logo

P/N 0901000010

Red Reflectors

P/N 2738332

SE6 05/05 Safety Section 1-24

Page 31

DANGER! Guard Missing Do Not Operate.

SAFETY

P/N 00756004

DANGER! Rotating Driveline Keep Away, Contact can cause death.

P/N 00756005

SAFETY

SE6 05/05 Safety Section 1-25

Page 32

SAFETY

Federal Laws and Regulations

This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such.

Employer-Employee Operator Regulations

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as possible every working man and woman in the nation safe and healthful working conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer-

(1) shall furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;

SAFETY

Employer Responsibilities:

(2) shall comply with occupational safety and health standards promulgated under this Act.

(b) Each employee shall comply with occupational safety and health standards and all rules,regulations and orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Regulations

OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the employer shall instruct every employee in the safe operation and servicing of all equipment with which the employee is, or will be involved.”

To ensure employee safety during Tractor and Implement operation, it is the employer’s responsibility to:

1. Train the employee in the proper and safe operation of the Tractor and Implement.

2. Require that the employee read and fully understand the Tractor and Implement Operator’s manual.

3. Permit only qualified and properly trained employees to operate the Tractor and Implement.

4. Maintain the Tractor and Implement in a safe operational condition and maintain all shields and guards on the equipment.

5. Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee operator securely fasten the safety belt and operate with the ROPS in the raised position at all times.

6. Forbid the employee operator to carry additional riders on the Tractor or Implement.

7. Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the necessary support devices to secure the equipment safely while performing repairs and service.

8. Require that the employee operator stop mowing if bystanders or passerbys come within 100 yards.

Child Labor Under 16 Years of Age

Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.)

SE6 05/05 Safety Section 1-26

Page 33

Page 34

Page 35

Page 36

Page 37

Page 38

Page 39

Page 40

Page 41

Page 42

Page 43

Page 44

Page 45

Page 46

Page 47

Page 48

Page 49

Page 50

Page 51

Page 52

Page 53

Page 54

Page 55

Page 56

Page 57

Page 58

Page 59

Page 60

Page 61

Page 62

Page 63

Page 64

Page 65

Page 66

Page 67

Page 68

Page 69

Page 70

Page 71

Page 72

Page 73

Page 74

Page 75

Page 76

Page 77

INTRODUCTION SECTION

Introduction Section 2-1

Page 78

INTRODUCTION

This Rotary Mower is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine.

The purpose of this manual is to familiarize, instruct, and train. The Assembly Section instructs the owner/ operator in the correct assembly of the Mower using standard and optional equipment. The Parts Listing section is designed to familiarize the owner/operator with replaceable parts on the Mower. This section provides exploded assembly drawings of each mower component illustrating each piece and the corresponding part number.

Careful use and timely service saves extensive repairs and costly downtime losses. The Operation and Maintenance Sections of the manual train the owner/operator how to work the Mower correctly and attend to appropriate maintenance. The Trouble Shooting Guide helps diagnose difficulties with mower and offers solution to the problems.

Safety is of primary importance to the owner/operator and to the manufacturer. The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death. Many of the Safety Messages will be repeated throughout the manual. The owner/operator/dealer

INTRODUCTION

should know these Safety Messages before assembly and be aware of the hazards of operating this mower during assembly, use, and maintenance. The Safety Alert Symbol combined with a Signal Word, as seen below, is intended to warn the owner/operator of impending hazards and the degree of possible injury faced when operating this machine.

The lowest level of Safety Message; warns of possible minor injury. Decals located on the Cutter with this Signal Word are Black and Yellow.

Serious injury or possible death! Decals are Black and Orange.

Imminent death/critical injury. Decals are Red and White.

For Non-Agricultural use, OSHA, ASAE, SAE, and ANSI standards require the use of Chain Guards, Deflectors, or Solid Skirts at all times. The Mower manufacturer strongly recommends the use of Chain Guards or Rubber Deflectors for Agricultural purposes as well, to reduce the risk of property damage, serious bodily injury, or even death from objects thrown out by or from contact with the Cutting Blades.

At least 20% or the tractor’s weight must be on the front tires with the Mower lifted to provide adequate traction for safe steering under good conditions. Slow down on hills, rough terrain, and curves.

The front, rear, left, and right are determined by the normal direction of travel, the same as driving an automobile.

SE5 05/05 Introduction Section 2-2

Page 79

INTRODUCTION

Your RHINO SE6 mower is designed for light-duty cutting such as pasture mowing, weed and grass control, and cutting brush up to 1" in diameter. With a reasonable amount of preventive maintenance, your Mower will provide years of dependable service.

SE5 05/05 Introduction Section 2-3

Page 80

INTRODUCTION

Attention Owner/Operator

BEFORE OPERATING THIS MACHINE:

1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and know how to operate correctly both the tractor and implement.

2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the implement. Mail within 30 days of delivery date of this implement.

NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by Alamo Group within thirty days of delivery of the implement.

3. Record the Blade Model and Serial Numbers on the Warranty page at the front of the Operator’s Manual. Keep this as part of the permanent maintenance file for the implement..

INTRODUCTION

SE5 05/05 Introduction Section 2-4

Page 81

ASSEMBLY SECTION

Assembly Section 3-1

Page 82

ASSEMBLY

DEALER SETUP INSTRUCTIONS

Set up mower as received from factory with these instructions.

This mower is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Refer to bolt torque chart in Maintenance Section. All bolts are Grade 5 unless otherwise specified.

1. Position on flat surface.

2. Apply light oil to gear box input shaft.

SHIELD ASSEMBLY (Figure AsmP-R-0016)

Before installing gearbox shields, check lubricant level in gearbox. Refer to Maintenance Section - Gearbox. Attach cotter pin and cable assembly (#5) through top shield bracket (#2) from outside in. Remove the top two bolts (#6) on the front of the gearbox housing. Align holes in the top shield bracket (#2) and gearbox. Reinstall the bolts & lockwasher (torque to 33 ft. lbs.) Attach cotter pin (#5) through top shield (#1) from outside in. Attach shield (#1) to top bracket (#2) and secure with flatwasher (#3 not shown) and nut (#4).

ASSEMBLY

SE6 05/05 Assembly Section 3-2

Page 83

ASSEMBLY

A-FRAME INSTALLATION (FIGURE Asm-R-0075).

1. Attach the Right and Left Hitch Ears (1 & 2) to the Mainframe with eight M12 x 40 bolts (3), retain with Flatwashers (5), and Nuts (6).

2. Attach the A-Frame Bars (7) to the right and left Hitch Ears (1 & 2) with two Cat. 1 Hitch Pins (8), Flatwashers (9), and Nuts (10).

3. Attach the Lift Strap Bars (11) to the Mainframe with two M12 x 30 Bolts (12), and Nuts (13).

4. Attach the Lift Strap Bars (11) to the A-Frame Bars (7) with one Bolt (14), Top Link (15), Bushing, (16), and Nut (17).

5. Tighten all bolts to the proper torque.

ASSEMBLY

SE6 05/05 Assembly Section 3-3

Page 84

ASSEMBLY

TAIL WHEEL INSTALLATION (FIGURE Asm-R-0076).

1. Attach the Gauge Wheel Mount Weldment (1) to the Mainframe with four M14 x 35 Bolts (3), and Nuts (4).

2. Align Tail Wheel Beam Weldment (5) between pivot brackets located behind gearbox mount on the Mainframe Weldment. NOTE: Long side of caster fork pivot tube is positioned up. Attach the Tail Wheel Beam Weldment (5) to the Mainframe Weldment with one M16 x 90 Bolt (6), and Nut (7). Slide Tail Wheel Beam Weldment (5) into Gauge Wheel Mount Weldment (1) and retain with two M12 x 80 Bolts (8), and Nuts (9).

3. Insert the Caster Fork Weldment (10) into the Tail Wheel Beam (5) and retain with Flatwasher (11) and Cotter Pin (12).

4. Tighten all bolts to the proper torque.

ASSEMBLY

SE6 05/05 Assembly Section 3-4

Page 85

ASSEMBLY

TONGUE ASSEMBLY PULL-TYPE MOWER (FIGURE Asm-R-0077)

To assemble the mower’s tongue, follow the procedures listed below. Note: Certain assembly steps may have been performed by the manufacturer before delivery.

1. Securely block the mower 12-18” off the ground.

2. Locate the left and right hitch ear plates (1 and 2). Position ear plates on respective sides of mower deck and align four holes of each plate with holes of mower deck frame. When correctly positioned there will be two holes at the top of each plate positioned away from the deck center (see diagram). Secure each ear plate to deck frame with four 12mm x 40mm bolts (15), 12 mm flat washers (14), and 12 mm locknuts (13).

3. Insert bushings (10) into holes of tongue weldment (3) connecting arms. Position connecting arms to the outside of the ear plates aligning the plates upper holes with arm holes and bushing. NOTE: Tongue weldment must be positioned with the offset drop downward such that the tongue is level with the deck. Place a washer (11) against each bushing and secure tongue to plates with 7/8” x 2” bolts (12) and 7/8” locknuts (9).

4. Place trunion (8) inside set of tongue weldment lug holes, center trunion hole between lugs and place bushing (7) into trunion. Insert adjusting bolt (6) through bushing and trunion and screw into 3/4” nut (16) and leveling rod nut (17). NOTE: The opposite end of the adjusting rod is attached during the Tail Wheel Assembly. The adjustment bolt is used to set the pitch of the mower deck and the leveling rod raises or lowers the front and rear of the mower equal amounts when the tail wheels are raised or lowered. To raise the front of the mower deck, screw the adjustment bolt clockwise. To lower the front of the mower, screw the adjustment bolt counterclockwise.

5. Attach jack (4) and chain (5) onto tongue weldment.

6. Tighten all bolts and nuts per recommended torque at this time.

ASSEMBLY

SE6 05/05 Assembly Section 3-5

Page 86

ASSEMBLY

TAILWHEEL- ASSEMBLY PULL-TYPE MOWER (FIGURE Asm-R-0078)

To assemble the Mower’s Tail Wheels, follow the procedures listed below. Note: Certain assembly steps may have been performed by the manufacturer before delivery.

1. Securely block the mower 12-18” off the ground.

2. To attach the wheel and tire assemblies (1) to the axle weldment (8), center a bushing (2) on each side of the tail wheels. Place tail wheel and bushings inside fork of axle weldment and align holes of wheel, bushing, and fork. Insert spindle weldment (3) through fork, bushings, and wheel and secure in position with a 1” locknut (4).

3. Place axle lug (5) between the large set of axle weldment beam lugs (lugs will have two holes). Axle lug should be positioned with its curvature facing the direction of the tailweels. Retain the axle lug to the axle weldment with two 1”x 2-1/2” bolts (6) and 1” locknuts (7).

4. Position axle weldment beam farthest lugs to the outside of the two farthest lugs on the mower deck. The axle beam must be positioned with the axle lug to (5) to the top. Insert bushing ( 21) into lugs of axle and 3/4” washer (10) against bushing. Align holes of lugs and bushings and retain axle to mower deck with two 3/4” x 1-3/4” bolts (9) and 3/4” locknuts (11).

5. Place axle cylinder lugs (16) to the outside of welded lugs behind gearbox. Align holes and retain all four

ASSEMBLY

pieces in position with two 5/8” x 3-1/2” bolts (17) and 5/8” locknuts (18).

6. Place bushing (20) into end hole of leveling rod (19). Position leveling rod end hole and bushing between remaining set of lugs on axle weldment, align holes, and retain in position with a 3/4” x 1-3/4” bolt (9) and 3/4” locknut (11). Note: The opposite end of the adjustment rod is attached during Tongue Assembly.

7. Align one rachet (12) end fork to the outside of the axle lug (5) top hole and retain in place using the short pivot pin (13) and cotter pin (14).

8. Align other rachet end fork between set up upright bolted lugs on mower deck behind gearbox. Insert long pivot pin (15) through lugs and rachet end fork and retain in position with pins. Note: The rachet is used to raise and lower the mower deck. A hydraulic cylinder can be installed in its position to allow for manipulation of deck height while driving.

9. Tighten all bolts and nuts per recommended torque at this time.

SE6 05/05 Assembly Section 3-6

Page 87

ASSEMBLY

SHEAR BOLT or SLIP CLUTCH DRIVELINE INSTALLATION

Attach rear driveline of U-Joint to input Shaft on gearbox, install Snap Ring in groove on Input Shaft. NOTE: Check that Snap Ring is properly seated in groove. This Snap Ring retains Driveline when shear bolt shears.

Install Grade 2 (only) shear bolt 1/2" by 3-1/2". Use of a stronger shear bolt than Grade 2, will result in driveline failure and will void warranty. Figure Asm-R-0072.

Attach slip clutch driveline to input shaft on gearbox with Grade 8 Bolt Figure Asm-R-0073. Refer to proper Torque Chart in Maintenance Section of this manual.

SE6 05/05 Assembly Section 3-7

Page 88

ASSEMBLY

Front and Rear Deflectors (Standard Equipment)

Front and Rear rubber-fabric Deflectors are Standard Equipment and Front and Rear Chain Guards are optional . One type of guard must be installed (and maintained in good repair) except for agricultural purposes only in areas where persons, vehicles, livestock, or other property will not be endangered by thrown objects and where such safety equipment would prevent the mower's reasonable performance of its assigned agricultural task.

Assy01-Shielding

Deflectors: Front and Rear Deflectors (Standard Equipment) are recommended for the average user and will provide protection from thrown objects with proper operation under normal conditions. Deflectors must be maintained in good repair or replaced after no more than two inches of wear off lower edge.

Front Rubber Fabric Deflectors (Standard Equipment)

Front Deflector (Figure Asm-0003)

1. Attach the Front Bracket (9) to the front of the

ASSEMBLY

mower with 1/2" x 3" Bolts (8), Flatwashers (6) and Locknuts (7).

2. Attach the Front Deflector (11) to the Bracket with 3/8" x 1-1/2" Bolts (2), Flatwashers (3), and Locknuts (1).

3. Attach the corner plate (10) to the side of the deck with a 1/2” x 1-1/2” Bolt (4). and Locknut (5).

Rear Deflector - Figure Asm-R-0080

1. Attach both Deflectors (1 & 2) to deck using 1/ 2" x 1-1/4" Bolts (5) and Locknuts (6). In center of deck use 1/2" x 4" Bolt (8) and Locknut (6) to tie both Deflectors (1 & 2) together.

2. Secure Debris Deflector (3) to Deflector (1 & 2) using 1/2" x 1-1/4" Bolts (5), Bar (4), Flatwashers (7), and Locknuts (6).

3. Fasten Rear Plate (9) on both ends of Deflector (1 & 2) using 1/2" x 1-1/4" Bolts (5) and Locknuts (6).

SE6 05/05 Assembly Section 3-8

Page 89

ASSEMBLY

CHAIN GUARDS (Optional Equipment at extra cost) (Figures Asm-R-0081 & Asm-R-0082)

CHAIN GUARDS: Front and Rear Chain Guards (Optional Equipment) are recommended for higher than

normal usage (100 hours or more per year) and will provide protection from thrown objects with careful operation. Chain Guards must be maintained in good repair by replacing missing or worn sections or by being replaced when seriously worn or damaged.

Front Chain Guards (Figure Asm-R-0081)

Rear Chain Guard - (Figure Asm-R-0082)

1. Attach both Deflectors (1 & 2) to deck using 1/ 2" x 1-1/4" Bolts (4) and Locknuts (5). In center of deck use 1/2" x 4" Bolt (7) and Locknut (5) to tie both Deflectors (1 & 2) together. See Figure

Asm-R-0082.

2. Secure Chainguard Assembly (3) to Deflectors (1 & 2) using 1/2" x 1-1/4" Bolts (4), Flatwashers (6), and Locknuts (5).

3. Fasten Rear Plate (8) on both ends of Deflectors (1 & 2) using 1/2" x 1-1/4" Bolts (4) and Locknuts (5). Figure Asm-R-0082.

1.Attach Chainguard Plate (1) to deck using 5/8" x 1 3/4" Bolts (4), Washers (5), and Locknut (6).

2.Insert the individual Chain Links (2) into slotted holes in Chain Guard Plate (1) and secure in place with Rod (3) as shown in Figure Asm-R-0081. (Complete Chainguard Assemblies are available. See Parts Section in this book.)

3.Attach the corner plate (7) to the side of the deck with a 1/2" x 1-1/2" Bolt (8), and Locknut (9). See

Figure Asm-R-0081

ASSEMBLY

SE6 05/05 Assembly Section 3-9

Page 90

ASSEMBLY

CHECK CHAINS (Extra Equipment) - FIGURE Asm-R-0083

Check chains are available for attachment to front of cutter as an accessory. Check chains are used to control cut height and especially allows cutter to always be lowered to the same preset cut height.

Drill a 11/16" hole through each lifting lug 2-1/2" below the lift pins and 5/8" from the front of the lug.

Install lower end of check chain (3) to hitch ears, through lower holes using capscrews and locknuts (5). Tighten securely.

Install chain lugs (2) on either side of tractor top link mounting (4) using bolt or pin of required diameter and length. Cat. I kit requires a 3/4" diameter bolt.

Cutting height is then set by placing proper chain link in keyhole slot. Cutting height is easily adjusted by hooking chain higher or lower in the keyhole brackets (1).

ASSEMBLY

NOTE: For additional safety in transport, raise mower as high as possible without allowing the driveline to

contact the deck, and shorten the chains as much as possible to prevent inadvertent falling in transport. CHECK TO BE SURE GEARBOX IS FILLED WITH LUBRICANT TO THE TEST PLUG LEVEL.The lubricant required is NLGI-000 EP (Rhino P/N 00769030)

SE6 05/05 Assembly Section 3-10

Page 91

ASSEMBLY

OFFSET ADAPTER HITCH (EXTRA EQUIPMENT) (Figure Asm-R-0084)

Fasten the Offset Adapter Tube to the three-Point Lift Lugs using the hitch Pin Holes. Fasten the Adjustable Leg to the right Lug to offset the Mower to the right. Fasten the Adjustable Leg to the left Lug to offset the Mower to the Left. The Mower will cut cleaner behind the wheel tracks if it is offset to the left.

Install the Adapter Brace Bar to one gearbox mounting bolt. Fasten the Chain End to the Mainframe (hole in left Stiffener). Adjust the Brace Bar so the Adapter is in a near perpendicular position.

Attach the Mower to the tractor. Attach Stabilizer Bars to prevent side sway of Mower.

Stabilizer Bars or Sway Chains must be installed and adjusted tightly. Without these bars or chains, serious damage to the Driveline can occur, and broken parts could cause bodily injury to the operator or bystanders. Stabilizer Bars or Sway Chains are available at most tractor dealerships.

Raise the mower to check clearance between the Driveline and Mower Deck. Set the lift stop on the tractor to ascertain that the Driveline does not strike the deck.

ASSEMBLY

SE6 05/05 Assembly Section 3-11

Page 92

Page 93

OPERATION SECTION

Operation Section 4-1

Page 94

OPERATION

RHINO SE6 ROTARY MOWER

OPERATION INSTRUCTIONS

Rhino SE6 rotary mowers are manufactured with quality material by skilled workers. These mowers are designed to cut grass, weeds, small brush and other vegetative material up to 1” diameter in areas such as pastures, industrial areas, and roadsides. The mower is equipped with protective deflectors and/or chain guards to prevent objects being thrown from the mower by the blades, however, no shielding is 100% effective. All shields, guards, deflectors, and chains equipped on the unit must be maintained on the mower in good operational condition.

It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the mower, tractor, or a thrown object. Do not operate the mower if passersby, pets, livestock, or property are directly in front or to the rear of the unit.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper mower use to the operator. Pictures contained in this section are intended to be used as a visual aid to assist in

OPERATION

explaining the operation of a rotary mower and are not of a SE6 cutter. Some pictures may show shields removed for purposes of clarity. NEVER OPERATE this implement without all shields in place and in good operational condition. The operator must be familiar with the mower and tractor operation and all associated safety practices before operating the mower and tractor. Proper operation of the SE6 mower, as detailed in this manual, will help ensure years of safe and satisfactory use of the mower.

IMPORTANT: To avoid mower damage, retorque all bolts after the first 10 hours of operation. Retighten blade carrier retaining nut on gearbox lower shaft to 300 ft. lbs.

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND MOWER.

If you do not understand any of the instructions, contact your nearest authorized dealer for a full explanation. Pay close attention to all safety signs and safety messages contained in this manual and those affixed to the cutter and tractor. OPS-U- 0001

READ, UNDERSTAND, and FOLLOW death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards.

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad.

the following Safety Messages. Serious injury or

(SG-2)

(SG-3)

SE6 05/05 Operation Section 4-2

Page 95

OPERATION

The M

ifi

Standard Equipment and Specifications

SE6

Horsepower Required 30-50 HP

Cutting Capacity (Max.) 1”

Cutting Height 1-7/8” Min.

Safety Deflector Std.

Cutting Width 72”

Overall Length 107-3/4”

Weight (Approx.) 728 lbs

Hitch CAT I (lift), Clevis (pull)

Blade Carrier Pan

Blade Tip Speed (FPM) 14,930

Gearbox Rating:

540 RPM 65 HP*

Output Shaft Diameter 1-9/16”

Driveline Size Cat 3

Deck Thickness 10 Ga.

Side Skirt 10 Ga. x 8”

Transport Width 78-5/8”

Jack Stand Std. (pull)

OPERATION

*Ratings based on actual field performance.

ower is designed for certain mowing applications and is rated to cut up to a spec vegetation (see Mower Standard Equipment and Specifications). DO NOT use this mower to cut vegetation above the Mower’s rated capacity or to cut any type of non-vegetative material. Only operate this Mower on a properly sized and equipped Tractor. Operating this Mower in an

application for which it is not designed and/or operating the Mower with the wrong size Tractor can cause Mower component damage and equipment failure resulting in possible serious injury or death.

SE6 05/05 Operation Section 4-3

(SGM-14)

c size

Page 96

OPERATION

1. OPERATOR REQUIREMENTS

Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor operation and all associated safety practices. In addition to the safety messages contained in this manual, safety decals are affixed to the implement and tractor. If any part of the operation and safe use of this equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely understand the operation of the equipment, it is the responsibility of the supervisor to read and explain the manuals, safety practices, and operating instructions to the operator.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment (PPE) for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is designed to provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

OPERATION

• Protective Eye Glasses, Goggles, or Face Shield

•Hard Hat

• Steel Toe Safety Footwear

• Gloves

• Hearing Protections

• Close Fitting Clothing

• Respirator or Filter Mask (depends on mowing conditions) OPS-U- 0002

SE6 05/05 Operation Section 4-4

(SG-27)

Serious injury or death to the

Page 97

OPERATION

2. TRACTOR REQUIREMENTS

The tractor used to operate the mower must have the power capacity to lift, pull, and operate the Power Take Off (PTO) at the mower’s rated speed while traveling at a ground speed between 2 and 5 MPH. Operating the mower with a tractor that does not meet the following requirements may cause tractor or mower damage and be a potential danger to the operator and passersby.

Tractor Requirements and Capabilities

• ASAE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt.

• Tractor Safety Devices ..................... Slow Moving Vehicle (SMV) emblem, lighting, PTO master shield

• Tractor Horsepower:

-Minimum .................. 30 HP

-Maximum .................. 75 HP

• Hitch -Lift Type Mower:

- Lifting Capacity ........730 lbs.

- 3-Point Hitch ............CAT I

-Pull Type Mower

-Drawbar ....................Extended 14” from PTO shaft end with safety chain attachment point

-Hydraulics................. Optional

• Front End Weight ............................. As needed to maintain 20% weight on front axle

• Power Take Off................................. 540 RPM 6-spline, 1-3/6” diameter output shaft

OPERATION

2.1 ROPS and SEAT BELT

The tractor must be equipped with a Roll-Over-Protective-Structure (ROPS) (tractor cab or roll-bar) and seat belt to protect the operator from falling off the tractor, especially during a roll over where the driver could be crushed and killed. Only operate the tractor with the ROPS in the raised position and seat belt fastened. Tractor model not equipped with a ROPS and seat belt should have these life saving features installed by an authorized dealer. OPS-U- 0003

(SG-7)

SE6 05/05 Operation Section 4-5

Page 98

OPERATION

2.2 Tractor Safety Devices

If transporting or operating the tractor and mower near a public roadway, the tractor must be equipped with proper warning lighting and a Slow Moving Vehicle (SMV) emblem which are clearly visible from the rear of the unit. Lights and a SMV emblem must be equipped directly on implements if the visibility of the tractor warning signals are obscured.

Maintain all manufacturer equipped safety shields and guards. Always replace shields and guards that were removed for access to connect, service, or repair the tractor or mower. Never operate the tractor PTO with the PTO master shield missing or in the raised position. OPS-U- 0004

2.3 Tractor Horsepower

The power required to operate a mower is determined by the tractor PTO horsepower. For most mowing conditions, the SE5 mower requires a tractor with at least 20 HP. Operating the mower with a tractor that does not have adequate power may damage the tractor engine. Exceeding 50 HP may cause mower damage by overpowering the unit in heavy cutting conditions.

OPERATION

2.4 3-Point Hitch

The tractor 3-point hitch must be rated to lift at least 730 lbs.

The SE6 mower is designed to be mounted on a tractor with a CAT I 3-point hitch. Refer to the tractor operator’s manual for the category of the tractor being used. If the hitch does not conform to ASAE CAT I dimensions, the mower may not fit or raise properly. Consult an authorized dealer for possible modification procedures to mount nonconforming hitches.

Depending on the hitch category, certain size pins are used to attach the mower to the tractor. CAT I hitches require 7/8” lower and 3/4” upper diameter hitch pins.

CAT I Implement / Hitch Specification

Width from outside to outside A-frame.... 26 7/8”

Quick Hitch width inside lug to lug ......... 27 1/8”

Height from bottom hitch pin to top pin... 18”

Lower pin diameter ................................. 7/8”

Upper pin diameter ................................ 3/4”

Lynch pin diameter ................................. 15/32”

SE6 05/05 Operation Section 4-6

Page 99

OPERATION

2.5 Front End Weight

A minimum of 20% total tractor weight must be maintained on the tractor front end at all times. Front end weight is critical to maintain steering control and to prevent the tractor from rearing up while driving. If the front end is too light, add weight until a minimum of 20% total weight is reached on the front tires. Front weights and weight carriers can be purchased through an authorized tractor dealership. OPS-U- 0005

2.6 Drawbar-Pull Type Mower

For equipment operating at 540 RPM, the tractor drawbar must be positioned at a 14” distance from the hitch point to the PTO shaft end for proper operation and minimal wear to the driveline.

If attaching the mower tongue clevis to a 3-point hitch drawbar supported by the lower lift arms, the attaching point must be extended past the main bar to allow for turning without binding the clevis and bar. Lift arm stabilizers must be used with this type of drawbar to prevent the mower from swaying from side to side.

OPERATION

OPS-R- 0061

SE6 05/05 Operation Section 4-7

Page 100

OPERATION

2.7 Power Take Off (PTO)

Depending on the unit, the mower is designed to operate at a PTO speed of 540 or 1000 RPM. Most tractors operate at either 540, or a combination of 540 and 1000 RPM PTO speeds. The operating speed of the mower and tractor can be determined by the number of splines on the driveline yoke and PTO output shaft. Those operating at 540 RPM will have a 6-spline shaft and those operating at 1000 RPM will have a 21-spline shaft. Note: The mower will not operate on tractors equipped with a 1000 RPM 20-spline, 1-3/4” shaft. Refer to the tractor owner’s manual for instructions to change PTO speeds on models that operate at more than one speed.

If operating an older model tractor where the tractor’s transmission and PTO utilize one master clutch, an over-running clutch must be used between the PTO output shaft and the driveline of the mower. An authorized tractor dealer can provide the over-running clutch and its installation if needed. OPS-U- 0006

DO NOT use a PTO adapter to attach a non-matching Implement driveline to a Tractor PTO. Use of an adapter can double the operating speed of the Mower resulting in excessive vibration,

OPERATION

thrown objects, and blade and mower failure. Adapter use will also change the working length of

(S3PT-14)

Never operate the Tractor and Mower if the Implement input driveline is directly connected to the

Tractor transmission. Tractor braking distances can be substantially increased by the momentum

of the rotating Mower blades driving the Tractor transmission even though the Tractor clutch has

been disengaged. Install an over running clutch between the Tractor PTO and the Mower driveline to prevent this potentially dangerous situation.

(S3PT-16)

3. GETTING ON AND OFF THE TRACTOR

Before getting onto the tractor, the operator must read and completely understand the implement and tractor operator manuals. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. OPS-U- 0007

Do not mount the Tractor while the tractor is moving. Mount the Tractor only

when the Tractor and all moving parts are completely stopped.

(SG-12)

SE6 05/05 Operation Section 4-8

Blue Rhino FC-0007 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

ROTARY MOWER

OPERATOR’S MANUAL

RHINO®

To the Owner/Operator/Dealer

Alamo Group Ag. Division is willing to provide

one (1) AEM Mower Safety Practices Video

TABLE OF CONTENTS

SAFETY SECTION

General Safety Instructions and Practices

Operator Safety Instructions and Practices

Equipment Operation Safety Instructions and Practices

Transporting Safety Instructions and Practices

Maintenance and Service Safety Instructions and Practices

Storage and Parking Safety Instructions and Practices

Concluding Safety Instructions and Practices

Decal Location

1. 00773723 1 PELIGRO Rotating Driveline Translation

2. 00769736 1 WARNING Use/Repair Shields & Guards

3. 00725746 1 PELIGRO Get Safety Translated

4. 00760657 1 IMPORTANT Genuine Parts, Rhino Rotary

5. 00763977 1 INSTRUCT Notice to Owner

6. 00756494 1 DANGER Driveline Hazards

7. 00769737 1 DANGER Blades-Thrown Objects

8. 00749117 1 DANGER Multiple Hazard

9. D302 2 LOGO Rhino Logo

10. 00763613 1 INSTRUCT Slip Clutch Adjustment

11. D103 1 INSTRUCT 540 RPM

12. D303 2 NAME Rhino Name

13. 0901000010 2 NAME SE5 Name Decal

14. 2738332 2 REFLECT Red Reflector

15. 00756004 ((1)) DANGER Driveline Shield Missing

16. 00756005 ((1)) DANGER Rotating Driveline

17. NFS 1 SRL PLT Serial Plate

18. 00776031 1 Canister, Operators Manual

19. 00768614C 1 Operator’s Manual

20. 10058000 3 Bolt

21. 00017000 3 Lockwasher

22. 00024100 6 Flatwasher

23. 02959924 3 Locknut

1. 00773723 1 PELIGRO Rotating Driveline Translation

2. 00769736 1 WARNING Use/Repair Shields & Guards

3. 00725746 1 PELIGRO Get Safety Translated

4. 00760657 1 IMPORTANT Genuine Parts, Rhino Rotary

5. 00763977 1 INSTRUCT Notice to Owner

6. 00756494 1 DANGER Driveline Hazards

7. 00769737 1 DANGER Blades-Thrown Objects

8. 00749117 1 DANGER Multiple Hazard 8a. 00756059 1 WARNING Hydraulic Oil Leak

9. D302 2 LOGO Rhino Logo

10. 00763613 1 INSTRUCT Slip Clutch Adjustment

11. D103 1 INSTRUCT 540 RPM 11a. D102 1 INSTRUCT PTO Shaft

12. D303 2 NAME Rhino Name

13. 0901000010 2 NAME SE5 Name Decal

14. 2738332 2 REFLECT Red Reflector

15. 00756004 ((1)) DANGER Driveline Shield Missing

16. 00756005 ((1)) DANGER Rotating Driveline

17. NFS 1 SRL PLT Serial Plate

18. 00776031 1 Canister, Operators Manual

19. 00768614C 1 Operator’s Manual

20. 10058000 3 Bolt

21. 00017000 3 Lockwasher

22. 00024100 6 Flatwasher

23. 02959924 3 Locknut

Decal Description

Federal Laws and Regulations

INTRODUCTION SECTION

Attention Owner/Operator

ASSEMBLY SECTION

DEALER SETUP INSTRUCTIONS

1. Position on flat surface.

2. Apply light oil to gear box input shaft.

SHIELD ASSEMBLY (Figure AsmP-R-0016)

A-FRAME INSTALLATION (FIGURE Asm-R-0075).

1. Attach the Right and Left Hitch Ears (1 & 2) to the Mainframe with eight M12 x 40 bolts (3), retain with Flatwashers (5), and Nuts (6).

2. Attach the A-Frame Bars (7) to the right and left Hitch Ears (1 & 2) with two Cat. 1 Hitch Pins (8), Flatwashers (9), and Nuts (10).

3. Attach the Lift Strap Bars (11) to the Mainframe with two M12 x 30 Bolts (12), and Nuts (13).

4. Attach the Lift Strap Bars (11) to the A-Frame Bars (7) with one Bolt (14), Top Link (15), Bushing, (16), and Nut (17).