ITEM/ARTICLE/ARTÍCULO #0005884
MODEL/MODÈLE/MODELO #55424
BICYCLE PULLEY
Hook Pulleys
x2
Rope Cleat
x1
48 ft. Rope
x1
Pulley Plate
x1
Lift Assembly
x1
#10x50.4 mm Screw
x14
Screw Eye Hook
x1
PACKAGE CONTENTS/
HARDWARE CONTENTS/
PREPARATION/
A C
E
DB
AA
BB
Bicycle not included
Before beginning installation of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
Estimated Installation Time: 15 minutes
Tools Required for Assembly (not included): Phillips screwdriver.
Helpful Tools (not included): Drill with bit, stud finder (if mounting item to the wall).
WARNING: Handling this product will expose you to chemicals, including lead, known to the state of California to cause birth
defects or other reproductive harm. Wash hands after handling.
1
AB14503
AVERTISSEMENT :La manipulation de cet article peut vous exposer à des produits chimiques, notamment du plomb,
reconnus par l’État de la Californie comme étant la cause de cancers, d’anomalies congénitales et d’autres problèmes
liés aux fonctions reproductrices.Lavez-vous les mains après l’avoir manipulé.
ADVERTENCIA:La manipulación de este producto lo expondrá a sustancias químicas, incluido el plomo, reconocidas por el
estado de California como causantes de defectos congénitos u otros daños en el aparato reproductivo.Lávese las manos
después de manipularlo.
D
D
A
C
E
E
AA
BB
BB
INSTALLATION INSTRUCTIONS
Measure the distance between the handlebars and the back of
the seat of the bicycle (sold separately).
1.
2.
3.
Transfer the seat/handlebar measurement along a ceiling joist so the lift
assembly (E) and pulley plate (D) line up. If you need to mount the bicycle
pulley unit in the opposite direction of the joist, simply mount on a board and
then securely attach the board to the joist as shown. Secure the screw eye
hook (BB) about 12 in. from the pulley plate (D). Using the screws (AA),
mount the pulley plate (D) and the lift assembly (E) to the ceiling joist,
ensuring they line up with the handlebar/seat measurement (lift will operate
better if this measurement is accurate). Pre-drilling 1/8 in. pilot holes is
recommended.
Tie a double knot on the end of the rope (C). Feed the rope through the
screw eye hook (BB) and secure to the eyelet. Thread the rope through a
hook pulley (A), then pulley plate (D), then the second hook pulley (A) and
lift assembly (E) as shown. Be sure to the thread the rope down through
both parts of the locking mechanism in the lift assembly.
1
3
2
2
OPERATING INSTRUCTIONS/
AA
4. Use screws (AA) to mount the rope cleat (B) to the wall. DO NOT CUT THE
ROPE. When the bicycle is up to the ceiling, the excess rope should be
wrapped around the cleat.
Using the Bicycle Lift
Hook the bicycle handlebar and seat with the hooks and be sure the ropes are
not twisted.
The bicycle can now be raised to the ceiling by pulling the rope.
The rope will lock in place with each pull, preventing the bicycle from falling.
For safety, tie the rope on the cleat and wind the excess rope around it. DO
NOT CUT THE ROPE.
Lowering the Bicycle
Pull rope toward back pulley maintaining tension on rope (see figure).
The tension will keep the locking mechanism open and it will be possible to
lower the bicycle.
Slowly let the rope out as the bicycle lowers.
Once the bicycle is low enough, remove it from the hooks and tie the rope back
to the cleat.
4
3
B
Loading...