Bluefin BFMS1223PR-01, BFMS24BA-01O, BFMS09PL-02I, BFMS18PL-02I, BFMSMZ224PL-01 Remote User Guide

...

Page 1

REMOTE CONTROLLER

OWNER’S MANUAL

IMPORTANT NOTE:

Thank you for purchasing our air conditioner. Please read this manual carefully before operating your new air conditioning unit and make sure to save this manual for future reference.

Page 2

Table of Contents

Remote Controller Specifications

......................................................02

Handling the Remote Controller ....................................................03

Buttons and Functions ...................................................................04

Remote Screen Indicators ..............................................................08

How to Use Basic Functions ..........................................................09

How to Use Advanced Functions ..................................................11

Page 3

Remote Controller Specifications

My Mode

Swing

Mode

On/Off

Fan

Sleep

AUTO COOL DRY

HEAT

FAN

HIGH MED LOW

SET TEMPERATURE

RG10A(D2S)/BGEF, RG10A(D2S)/BGEFU1,RG10A1(D2S)/BGEF, RG10A2(D2S)/BGEFU1, RG10A2(D2S)/BGCEFU1, RG10A2(D2S)/BGCEF, RG10A10(D2S)/BGEF, RG10B(D2)/BGEF, RG10B1(D2)/BGEF, RG10B2(D2)/BGCEF,RG10B10(D2)/BGEF，RG10B10(D2)/BGCEF, RG10Y1(D2)/BGEF,RG10Y2(D2S)/BGEF

3.0V( Dry batteries R03/LR03×2)

-5°C~60°C(23°F~140°F)

NOTE: For units labeled RG10Y1 (D2)/BGEF,RG10Y2(D2S)/BGEF: If the unit is turned off while

set to COOL, AUTO or DRY mode with the set temperature less than 24°C, the set temperature

will be automatically set to 24°C when you turn on the unit again. If the unit is turned off under

HEAT mode with the set temperature more than 24°C, the set temperature will be automatically

set to 24°C when you turn on the unit again.

Quick Start Guide

FIT BATTERIES

PRESS POWER BUTTON

AUTO

COOL

DRY

HEAT

FAN

SELECT MODE

5 4

POINT REMOTE TOWARD UNIT

SELECT TEMPERATURE

SELECT FAN SPEED

NOT SURE WHAT A FUNCTION DOES?

Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

• Button designs on your unit may differ slightly from the examples shown. If the indoor unit does not have a particular function, pressing that function’s button on

•

the remote control will have no effect. When there are discrepancies between “Remote controller Manual” and “USER’S

•

MANUAL” on function description, follow the instructions outlined in the "USER'S MANUAL"

Page 4

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries. Put the batteries in the remote control before use.

Slide the back cover from the remote control downward, exposing the battery compartment.

Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.

Slide the battery cover back into place.

BATTERY NOTES

For optimum product performance:

•

Do not mix old and new batteries, or batteries of different types.

Do not leave batteries in the remote control

•

if you don’t plan on using the device for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.

• The unit will beep when remote signal is received.

• Direct sunlight, curtains, and other obstructions can interfere with the infrared signal receiver.

• If the remote isn't going to be used for a period of over 2 months, remove the batteries to prevent leakage.

NOTES FOR USING REMOTE CONTROL

This device complies with the local national regulations. In Canada, it should comply with

•

CAN ICES-3(B)/NMB-3(B). In USA, this device complies with part 15 of the

•

FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. v

Page 5

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions

Turns the unit on or off.

ON/OFF

TEMP

Increases temperate in 1°C (1°F) increments. Max. temperature is

30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.

GEAR(50%)

SET

Scrolls through operation functions as follows: Fresh( ) Sleep( ) Follow Me( ) AP mode( ) Fresh...

The selected symbol will flash on the display area, press the OK button to confirm.



TEMP

Decreases temperature in 1°C (1°F) increments Min. temperature is 16°C (60°F).

FAN SPEED

Selects fan speeds in the following order:

 



Press the TEMP or button to increase/decrease the fan speed in 1% increments.

20%



60% 40% 80% 100%.

SWING

Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature.

section of this manual.

MODE

Scrolls through operation modes as follows:

DRY

AUTO  COOL 

HEAT  FAN

NOTE: HEAT mode is not supported by the cooling only appliance.

ECO/GEAR

Press this button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%)

Previous setting

mode ECO

......

Used to confirm the selected

functions

TIMER

Sets timer to turn unit on or off

BREEZE AWAY

This feature activates indirect airflow for a more natural, breeze-like effect

NOTE: This feature is available under cool, Fan and Dry mode only

CLEAN

Used to start and stop the Self Clean or Active Clean function. (Model dependent, please refer to the USER’S OPERATION & INSTALLATION MANUAL).

LED

Turns indoor unit’s LED display and air conditioner buzzer on and off (model dependent), which creates a comfortable and quiet environment.

Turbo

Enables unit to reach preset temperature in shortest possible time

RG10A2(D2S)/BGEFU1,RG10Y2(D2S)/BGEF

Model:

RG10A10(D2S)/BGEF(20-28 C/68-82 F)

RG10A(D2S)/BGEF & RG10A(D2S)/BGEFU1(Fresh feature is not available) RG10A2(D2S)/BGCEFU1 & RG10A2(D2S)/BGCEF (Cooling only models, AUTO mode and HEAT mode are not available)

Page 6

Turns the unit on or off.

ON/OFF

TEMP

Increases temperate in 1°C (1°F) increments. Max. temperature is

30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.

SET

Scrolls through operation functions as follows: Breeze Away( ) Sleep ( )



Follow Me( )

AP mode( ) Breeze Away ...

The selected symbol will

flash on the display area, press OK button to confirm.



TEMP

Decreases temperature in 1°C (1°F) increments Min. temperature is 16°C (60°F).

FAN SPEED

Selects fan speeds in the following order:



 

Press the TEMP or button to increase/decrease the fan speed in 1% increments.

20%



60% 40% 80% 100%.

SWING

Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature.

MODE

Scrolls through operation modes as follows:

HEAT  FAN

DRY

AUTO  COOL 

NOTE: HEAT mode is not supported by the cooling only appliance.

ECO/GEAR

Press this button to enter the energy efficient mode in a sequence of following:

ECO GEAR(75%)

GEAR(50%)

mode ECO

Used to confirm the selected

functions

TIMER

Sets timer to turn unit on or off

Previous setting

......

FRESH

Used to start and stop the Fresh feature.

CLEAN

Used to start and stop the Self Clean or Active Clean function. (Model dependent, please refer to the USER’S OPERATION & INSTALLATION MANUAL).

LED

Turns indoor unit’s LED display and air conditioner buzzer on and off (model dependent), which creates a comfortable and quiet environment.

Turbo

Enables unit to reach pr temperature in shortest possible time

Model: RG10A1(D2S)/BGEF

Page 7

Turns the unit on or off.

ON/OFF

TEMP

Increases temperate in 1°C (1°F) increments. Max. temperature is

30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.

SET

Scrolls through operation functions as follows:

Fresh( )

AP mode( ) Fresh ....

The selected symbol will flash on the display area, press the OK button to confirm.

Follow Me( )



TEMP

Decreases temperature in 1°C (1°F) increments Min. temperature is 16°C (60°F).

FAN SPEED

Selects fan speeds in the following order: AUTO LOW MED HIGH

NOTE: Holding this button down for 2 seconds will activate Silence feature.



SWING

Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature(some units).

MODE

Scrolls through operation modes as follows:

DRY

AUTO  COOL 

HEAT  FAN

NOTE: HEAT mode is not supported by the cooling only appliance.

SLEEP

Saves energy during sleeping hours.

Used to confirm the selected functions

TIMER

Sets timer to turn unit on or off.

SHORTCUT

Used to restore the current settings or resume previous settings.

CLEAN

Used to start and stop the Self Clean or Active Clean function. (Model dependent, please refer to the USER’S OPERATION & INSTALLATION MANUAL).

LED

Turns indoor unit’s LED display and air conditioner buzzer on and off (model dependent), which creates a comfortable and quiet environment.

Turbo

Enables unit to reach preset temperature in shortest possible time

RG10B(D2)/BGEF(Fresh feature is not available)

Model:

RG10B10(D2)/BGEF & RG10B10(D2)/BGCEF(20-28 C/68-82 F)

RG10B2(D2)/BGCEF & RG10B10(D2)/BGCEF (Cooling only model, AUTO mode and HEAT mode are not available ) RG10Y1(D2)/BGEF

Page 8

Turns the unit on or off.

ON/OFF

TEMP

Increases temperate in 1°C (1°F) increments. Max. temperature is

30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.

SET

Scrolls through operation

functions as follows: Follow Me( ) AP mode ( )



The selected symbol will

flash on the display area, press OK button to confirm.



Follow Me( )...

TEMP

Decreases temperature

in 1°C (1°F) increments

Min. temperature is

16°C (60°F).

FAN SPEED

Selects fan speeds in the following order: AUTO LOW MED HIGH

NOTE: Holding this button down for 2 seconds will activate Silence feature.



SWING

Starts and stops the horizontal

louver movement. Hold down

for 2 seconds to initiate vertical

louver auto swing feature(some units).

MODE

Scrolls through operation modes as follows:

HEAT  FAN

DRY

AUTO  COOL 

NOTE: HEAT mode is not supported by the cooling only appliance.

SLEEP

Saves energy during sleeping hours.

Used to confirm the selected functions

TIMER

Sets timer to turn unit on or off

FRESH

Used to start and stop the air fresh feature.

CLEAN

Used to start and stop the Self Clean or Active Clean function. (Model dependent, please refer to the USER’S OPERATION & INSTALLATION MANUAL).

LED

Turns indoor unit’s LED display and air conditioner buzzer on and off (model dependent), which creates a comfortable and quiet environment.

TURBO

Enables unit to reach preset temperature in shortest possible time

Model: RG10B1(D2)/BGEF

Page 9

Remote Screen Indicators

Information are displayed when the remote controller is power up.

Breeze Away display(some units)

Active clean feature display

Fresh feature display

Sleep mode display

Follow me feature display

Wireless control feature display(some units)

Transmission Indicator

Lights up when remote sends signal to indoor unit

Low battery detection display(If flashes)

MODE display

Displays the current including:

mode,

TIMER ON display

TIMER OFF display

Silence feature

display

FAN SPEED display

Displays selected fan speed:

Silence

LOW

MED

HIGH

AUTO

This fan speed can not be adjusted in AUTO or DRY mode.

[ ]

Note:

Not all the models can display

the fan speed values between

AU-100%.

Note:

The indicators displayed in the above figure are for illustrative purposes only. During normal operation, only active functions and relevant information will be displayed.

2%-20% 21%-40%

41%-60%

61%-80%

81%-100%

* *

 

Horizontal louver swing display

Vertical louver auto swing display

TURBO mode display

Not available for this unit

 



ECO display

Displays when ECO feature is activated

GEAR display

Displays when GEAR feature is activated

LOCK display

Displays when LOCK feature is activated.

Temperature/Timer/Fan speed display

Displays the set temperature by default, or fan speed or timer setting when using TIMER ON/OFF functions.

Temperature range:

16-30 C / /60-86 F (20-28 C/68-82 F) (Model dependent)

Timer setting range: 0-24 hours

Fan speed setting range:

AU -100% This display is blank when operating in FAN mode.

Page 10

How to Use Basic Functions

ATTENTION

Before operation, please ensure the unit is plugged in and power is available.

AUTO Mode

Select AUTO mode Set your desired temperature

MODE

NOTE:

1. In AUTO mode,

the set temperature.

2. In AUTO mode, fan speed cannot be set.

the unit will automatically select the COOL, FAN, or HEAT function based on

COOL or HEAT Mode

Select COOL/HEAT mode

Set the temperature

MODE

DRY Mode

Turn on the air conditioner

Set the fan speed

Turn on the air conditioner

Select DRY mode Set your desired temperature Turn on the air conditioner

MODE

NOTE: In DRY mode, fan speed is automatically controlled and cannot be manually set.

FAN Mode

Select FAN mode Turn on the air conditioner

Set the fan speed

MODE

NOTE: In FAN mode, you can’t set the temperature. As a result the temperature won't be displayed on the remote's screen

Page 11

Setting the TIMER

ON/OFF

ODE

F AN

SHORT CUT

TIMER ON

TIMER OF

TEMP

S L

E EP

ON/OFF

M ODE

F AN

SHORT CU

M E R

O N

TIMER OF

TEMP

S L

E EP

ON/O

MODE

F AN

SHOR

CUT

M E R

O N

TIMER OF

TEM

S L

E EP

ON/OFF

ODE

F AN

SHORT CUT

TIMER ON

TIMER OF

TEMP

S L

E EP

TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

Press TIMER button to initiate the ON time sequence.

TIMER

TIMER OFF setting

Press TIMER button to initiate the OFF time sequence.

TIMER

NOTE:

1. When setting the TIMER ON or TIMER OFF, the time will increase in 30 minute increments up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.

2. Cancel either function by setting its timer to 0.0h.

Press Temp. up or down button to set the desired time to turn on the unit.

Press Temp. up or down button to set the desired time to turn off the unit.

x10

Point remote to unit and wait 1 second. The timer will turn on.

1sec

Point remote to unit and wait 1 second. The timer will turn off.

1sec

TIMER ON & OFF setting(example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

TIMER

Timer starts

Unit turns

TIMER

Unit turns

OFF

Example: If current timer is 1:00PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30PM)

Current

time 1PM

2:00PM 3:00PM

2.5 hours later

5 hours later

3:30PM

4PM 5PM

6PM

and turn off at 6:00PM.

Page 12

How to Use Advanced Functions

Swing function

Press Swing button

Swing

The horizontal louver will swing up and down automatically when pressing Swing button. Press the swing button again to make it stop.

Swing

Hold the swing button for more than 2 seconds to activate the vertical louver swing function. (Model dependent)

Airflow direction

You can set five different airflow directions by continuing to press the swing button. The

Swing

NOTE: When the unit is off, press and hold MODE and SWING buttons together for one second. the louver will open to an angle convenient for cleaning. Press and hold MODE and SWING buttons together for one second to reset the louver (Model dependent).

louver can be move at a certain range each time you press the button.

until the direction you prefer is eached.

Press the button

LED DISPLAY

LED LED

Press LED button Hold this button more than

5 seconds (some units)

Press this button to turn the display on the indoor unit on and off.

Hold the button for 5 seconds to display the actual room temperature. Hold the button for 5 seconds again to revert to displaying the set temperature.

Page 13

ECO/GEAR function

Press this button to enter the energy efficient mode in a sequence of following:

ECO GEAR(75%) GEAR(50%) Previous setting mode ECO......

Note:This function is only available under COOL mode.

ECO operation:

While in cooling mode, press this button to automatically set the temperature to 24°C / 75°F, and the fan speed to Auto to save energy (only when the set temperature is less than 24°C / 75°F). If the set temperature is above 24°C / 75°F, press the ECO button to change the fan speed to Auto. The set temperature will remain the same.

NOTE: Pressing the ECO/GEAR button, modifying the mode or adjusting the set temperature to less than 24°C / 75°F will stop ECO operation. While in ECO mode, the set temperature should be 24°C / 75°F or higher. If your desired temperature is below 24°C / 75°F, you may need to turn off ECO mode by pressing the button again.

GEAR operation:

Press the ECO/GEAR button to enter the GEAR operation as following: 75%(up to 75% electrial energy consumption)

50%(up to 50% electrial energy consumption)

Previous setting mode.

In GEAR mode, the display on the remote controller will alternate between electical energy consumption and set temperature.

SHORTCUT function

Press SHORTCUT button(some units)

Push this button when remote controller is on to revert to the system's previous settings including operating mode, setting temperature, fan speed level and sleep feature (if activated).

Hold the button for more than 2 seconds to automatically restore the current operation settings including operating mode, setting temperature, fan speed level and sleep feature (if activated ).

Page 14

Silence function

FP function

Note: This function is for heat pump air conditioner only.

Press this button 2 times during one second under HEAT Mode and setting temperature of 16

C / 60°F or 20°C / 6°F(for models of RG10A10(D2S)/BGEF, RG10B10(D2)/BGEF and

RG10B10(D2)/BGCEF) to activate FP function. Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.

LOCK function

Hold Fan button for more than 2 seconds to activate/disable Silence function (some units).

Because the compressor operates at a lower frequency while in silent mode, you may notice reduced heating or cooling capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel silence function.

The unit will operate at high fan speed (while compressor on) with temperature automatically

set to 8

C / 46°F.

Clean

Turbo

Press and hold the Clean and Turbo buttons at the same time for more than 5 seconds to activate the lock function. After locking the remote, the buttons will not respond to input until the lock function is disabled by pressing and holding Clean and Turbo again for 2 seconds.

Page 15

SET function

SET

Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area. Press the OK button to confirm.

To cancel the selected function, just perform the same procedures as above.

Press the SET button to scroll through operation functions as follows:

Breeze Away ( ) Fresh ( ) Sleep( ) Follow Me( ) AP mode( ) [ ]: If your remote controller has Breeze Away button, Fresh button or Sleep button, you cannot

use the SET button to select the Breeze Away, Fresh or Sleep feature.

Breeze Away function ( ) (some units) :

This feature activates indirect airflow to create a more natural, breeze-like effect.

NOTE: This feature is available under cool, Fan and Dry mode only.

FRESH function ( ) (some units) :

When the FRESH function is initiated, ion generator is energized and will help to purify the air in the room.

Sleep function ( ) :

The SLEEP function is used to decrease energy use while you sleep (and don t need the same temperature settings to stay comfortable). This function can only be activated via remote control.

For the detail, see sleep operation in

USER S MANUAL.

Note:

* *

The SLEEP function is not available in FAN or DRY mode.

SET



the

 

Follow me function ( ):

The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this information to the air conditioner in 3 minute intervals. When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.

NOTE: Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function.

If the memory feature is activated, “ON” displays for 3 seconds on the screen.

If the memory feature is stopped, “OFF” displays for 3 seconds on the screen. While the memory feature is activated, press the ON/OFF button. Switching modes or power failure will not cancel the Follow me function.

AP function ( )(some units) :

Choose AP mode for wireless network configuration. For some units you may need to press the LED button seven times in 10 seconds to enter AP mode.

Page 16

The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.

CR2756-RG10(D2S) 16117000A37345

2021.05.08