Bloomfield TCT1 Installation Manual

CONVEYOR

TOASTER

MODEL

TCT1, TCT2, TCT3

Installation and

Operation

Instructions

2M-Z19588 Rev. - 12/16/2014

TCT1-120V

IL2904

SAFETY SYMBOLS

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual

CAUTION WARNING

accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Toastmaster factory supplied parts relieves the
manufacturer of all liability.

Toastmaster reserves the right to change specications and product design

without notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change

without notice. While Toastmaster exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the

specications. By using the information provided, the user assumes all risks in

connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it
ready when you call to ensure a faster service.

Authorized Service Agent Listing

Model No.

Serial No.

Voltage

Purchase Date

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.toastmastercorp.com
E-mail [e-mail]
Telephone: [phone]

The Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone]

Fax: [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

Mailing Address: Toastmaster

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

CAUTION

GENERAL INSTALLATION DATA

This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels associated with
the unit prior to putting it into operation. Make sure all people associated with its use understand the
units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both visible and concealed. This
unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If
equipment is received in damaged condition, either apparent or concealed, a claim must be made
with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a
request for inspection of concealed damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials for inspection. The carrier will make
an inspection and will supply necessary claim forms.

INSPECTION & ASSEMBLY

UNCRATING AND INSPECTING

Unpack the unit and components from the shipping container. Remove all visible packing material

and those from inside the cooking chamber. If damage is discovered, le a claim immediately with

the carrier that handled the shipment. Do not operate the unit if it was damaged during shipping.

ASSEMBLY AND INSTALLATION

The unit was shipped fully assembled and ready to plug into a standard outlet specied for its voltage
and amp draw. If improper electrical supply is determined, contact a qualied electrician prior to using

the unit. Plugging your toaster into the wrong voltage can result in damage to the unit and is NOT
covered under warranty. Removal and replacement of the power cord and plug will void the warranty.
For assistance, contact your local authorized service agent for service or required maintenance.

Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).

Before using the unit for the rst time, wipe down the exterior with a damp cloth.

WARNING

Allow enough space around the toaster for adequate ventilation. Do not operate the unit without the
crumb tray properly positioned. Overheating and poor toasting may occur. Read all labels on the unit
and follow their instructions.

ELECTRICAL CONNECTION

Before making any electrical connection to this unit, check that the power supply is adequate for the
voltage, amperage and requirements stated on the rating plate.
A wiring diagram is included herewith.

Disconnect the unit from the power source before installing or removing any parts.

Be absolutely sure that the ground connection for the receptacle is properly wired. Do not connect
equipment to power without proper ground connections. Improper grounding may result in personal
injury or fatality.

DO NOT CUT OR REMOVE THIS PLUG OR GROUNDING PRONG FROM

THE PLUG.

CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON

THE DATA PLATE OF THE UNIT.

WARNING

DAILY OPERATION

ROTARY POWER SAVER SWITCH

For toasters equipped with a Rotary Power Saver Switch, turn clockwise or counterclockwise to get in
the following positions.

FULL POWER

When in this position your equipment is at full power and ready to use.

OFF ROTARY

Two off positions are provided, a single rotation to either direction will shut the unit off.

STANDBY

The standby position reduces the power consumption by 75%. Using this position during the quiet
times will save electricity, and keep the toaster warm. When needed, turn the switch to FULL
POWER. Recovery time is about 30 seconds.

CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND

CARE SHOULD BE TAKEN WHILE USING THIS UNIT.

COOKING PROCEDURES

BREAD TOASTING

Some toasters are equipped with a swinging heat shutter at the toaster entrance. This shutter will
move out of the way as the product passes under it.

1) Turn the power saver to FULL POWER.

2) Set the conveyor speed to 50%.

4) Allow warm up time of 5 to 10 minutes.

5) Place a sample product on the conveyor belt to test the settings.

•If toasting is too light, turn conveyor speed control counterclockwise to a slower speed.

•If toasting is too dark, turn conveyor speed control clockwise to a faster speed.

(NOTE: Some products may require adjustment of the speed control in order to

achieve the desired results.)

Operate

Clean

IL2905

Crumb Tray Removal

TOASTER COMPONENTS

LOAD UP

FRONT

IL1555

CAUTION

CRUMB TRAY

SPEED CONTROL

POWER SAVER SWITCH

AIR INTAKE FAN

BOTTOM VIEW

POWER CORD

IL2906

DAILY OPERATION

Check the power cord to insure that it is plugged into a proper outlet.

Set the Rotary Power Saver Switch & speed control knob to desired settings.

Always allow 10 minutes of preheat time before loading the unit with product. Failure to allow

sufcient preheat time will result in unsatisfactory cooking until the unit reaches operating

temperature.

OPERATING HINTS AND SAFETY

Disconnect power to the unit with the switch at the end of each day of operation.

Do not leave the unit in operation without an attendant.

Turn Power Saver Switch to Standby during idle periods. It will take only a few minutes to regain
operating temperature.

Do not leave the unit at high temperature when not in use or during idle periods. This will cause food

particles and grease lm to carbonize.

CLEANING

Preventive maintenance for your Toastmaster toaster consists of the following recommended cleaning
procedures. To keep your toaster in its top operating condition, these steps should be performed on a
daily or weekly as indicated.

A. Turn main power saver switch to the OFF position. Disconnect unit from power source.

B. After the unit cools, remove interior crumb tray (as shown on page 4) and clean.

Slide crumb tray back into position.

C. Wipe exterior surface of unit.

D. Areas inside the toaster, be sure to unplug the unit and allow to cool prior to wiping clean

with a damp cloth.

E. Clean air intake on bottom of unit.

F. For lightly soiled conveyor belts, turn conveyor speed control to fastest setting and

wipe with a damp cloth (daily) For heavily soiled conveyors, turn conveyor speed control
to fastest setting, with crumb tray installed and wipe with a light abrasive pad
(as needed).

WARNING

DO NOT IMMERSE OR LET THE UNIT STAND IN WATER.

DO NOT HOSE DOWN THE UNIT OR THE TABLE/COUNTER IF THE UNIT IS
ON THE TABLE/COUNTER.

KEEP AWAY FROM RUNNING WATER.