Bloomfield SDS-1 General Manual

SATELLITE DOCKING STATION

General Layout Data Sheet

Page

2

Features

Page

3 Warranty

Page

4 Safety

Page

5

Leveling the Unit

Page

6

Initial Installation Instructions

Page

6 Quality Timer Adjustment Instructions

Page

7 Exploded View

Page

8 Parts Identification

Page

8 Ordering/Service Procedure

Page

9

S

chematic

—

Page

12

BLOOMFIELD MODEL: SDS-1

Introduction Page 1

Installation Instruction Page 6
Electrician's Installation Instructions Page 6

73342 Rev (-)

TABLE OF CONTENTS

Troubleshooting Page 10
Wiring Diagram Page 12

Printed in December, 1997

INTRODUCTION

BLOOMFIELD MODEL: SDS-l

HI-QUALITY SATELLITE DOCKING STATION

Thank you for purchasing a Bloomfield Satellite Docking Station.
maximum performance from this unit if you familiarize yourself with its many outstanding
features.
installation is very important if maximum performance and satisfaction are to be achieved.

If

you
have the required expertise to provide the proper advice and assistance.
Distributor is unable to assist you, please contact the factory directly.

Please be certain the electrical connections are compatible, as improper connections
could damage the Unit and void the warranty.

Safe and satisfactory operation of your Bloomfield Satellite Docking Station depends to a
great extent upon its proper installation.
without alteration and in accordance with these printed instructions and applicable electrical
codes.
in any way, or If installation deviates from the Instructions printed herein, and
be covered under any warranty service agreement.

This Bloomfield Docking Station has been designed with adjustment flexibility to cover a
wide spectrum of customer needs.

Please take a few minutes to read through the owner’s manual.

have

any difficulties, consult your nearest, Bloomfield Authorized Distributor.

This Satellite Docking Station must be installed

The performance and safety of the Brewer can be greatly Impaired If It Is altered

You will achieve

Proper

If the Bloomfield

will

They

not

1

GENERAL LAYOUT DATA BLOOMFIELD SATELLITE
DOCKING STATION

MODEL: SDS-1

ELECTRICAL SPECIFICATIONS

Model WATTS VOLTS AMPS

503-1 45 (with one Satellite) 120 .4

2

FEATURES

MODELS SDS-l SATELLITE DOCKING STATION manufactured by

BloomfIeld

Industries Inc., Is

designed to hold coffee at a correct temperature for serving.

0

Operates on 120 Volt, .4 Amp, 45 Watt service.

0

Safety feature including absence of any hot surfaces.

6

Automatic Start when Satellitte is in place,

0

Ideal for self service applications.

0

Auto safety electrical shut-off when Satellite is removed.

0

Adjustable non-skid rubber feet on brewer for easy leveling.

0

Adjustable coffee quality timer light which flashes at end of approved coffee holding time.

0

Optional Drip Tray.

0

Teflon color coded wiring, keyed to color tabs at connection points.

0

Unit size requires minimal counter space.

0

Satellite Brewer & Satellites OPTIONAL.

0

UL, CUL & NSF Listed UL & CUL:

0

Manufactured in USA

E9253)

(NSF: Standard

4)

3

WARRANTY POLICY

All electrical products manufactured by

in material and workmanship by our authorized service agents with:

o One

0

One (1) year. on labor

0

All genuine.

Labor includes cost of service invoice and is limited travel time to a sixty (60) mile

radius (or up to a maximum of one hour) to the nearest authorized service agency

or one of it’s sub-service agencies. This service

premises for non-portable models. Portable models (a device with a cord and plug)

must be taken or shipped to the closest authorized service agency; transportation

charges prepaid. All labor shall be performed during regular working hours.

premium

In addition to this warranty policy are the following exceptions:

A.

Warranty does not include any coverage for:

(1)

year replacement part warranty

Wells/Bloomfield

from date of purchase on non-warranty equipment.
only to replacements of the defective part.
parts completely voids any warranty.

will

be charged to the buyer.

Dispensers (i.e., tea and coffee) carry ninety (90) day parts replacement only.

replacement parts are warranted for ninety

Wells/Bloomfleld

Any use of non-genuine Bloomfield

will

are warranted against defects

(90)

days

This parts warranty is limited

be provided on the customers

Overtime

Resetting the safety thermostats, circuit breakers, overload protectors, or fuse

replacements unless warranted conditions are caused.
All problems due to operation at voltage other than specified on equipment

nameplates -conversion to correct voltage must be the customer’s responsibility.
All problems due to electrical connections not made in accordance with electrical

code requirements and wiring diagrams supplied with the equipment.
All problems due to inadequate water supply, such as fluctuating, high or low

water pressure, etc.
All problems due to mineral/calcium deposits, or contamination from chlorides

and or chlorines.
and not covered by warranty.

0

Calibration of thermostat.
such items as knobs, baskets, grids, mechanical timers, and thermocouples.
maintenance functions including lubrication, adjustment of thermostats, microswitches,
replacement of fuses, and Indicating lights.

0

Installation, labor, and job check-outs are not considered warranty.

De-liming is considered a preventative maintenance function

Replacement of items subject to normal wear to Include

Normal

4

THIS WARRANTY IS THE COMPLETE AND ONLY WARRANTY, EXPRESS OR IMPLIED IN LAW
OR FACT, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE, AND/OR FOR DIRECT, INDIRECT OR CONSEQUENTIAL
DAMAGES IN CONNECTION WITH
is determined that upon inspection by an authorized
the equipment has been modified, misused, misapplied, Improperly installed, or damaged in
transit or by fire, flood or act of nature.
or high or low water pressure are not covered by this warranty. It also does not apply If
the serial nameplate has been removed or service is performed by unauthorized personnel.

WELLS/BLOOMFIELD

All problems due to water supply, lime build-up,

PRODUCTS. This warranty is void if it

Wells/Bloomfield

dealer/distributor that

_

NOTE:

.

is provided with each unit.

SATELLITE DOCKING STATION IS VOID IF:
Other than genuine Bloomfield replacement parts are used.
Unit is plugged into voltage other than specified on serial plate.
Recommended Bloomfield servicing procedures are not followed.

A Warranty Statement and Complete Service Agency Listing with Warranty exclusions

SAFETY

Knowledge of proper procedures is essential to the safe operation of electrically energized
equipment.
potential hazards, the following 4 signal words are used throughout this chapter.

DANGER

!

severe personal injury, death, or substantial property damage in the event the
statement is ignored.

In accordance with generally accepted product safety labeling guidelines for

-

Danger is used to indicate the presence of a hazard which will cause

WARNING -Warning is used to indicate the presence of a hazard which can cause

!

severe personal injury, death, or substantial property damage in the event the
statement is ignored.

CAUTION -Caution is used to indicate the presence of a hazard which will or can

!

cause minor personal injury, or property damage in the event the statement Is
ignored.

NOTE- Note is used to notify personnel of installation, operation o& maintenance
information which is important, but not hazard related.

NOTE- This piece of equipment is made in the USA and has American sizes on
hardware.

Hazard Communication Standard
use of chemical products.
face letters followed by the abbreviation
Standard

All metric conversions are approximate and can vary in size.

(HCS)

These chemical products will be highlighted

(HCS)

Manual for the appropriate Material Safety Data Sheet(s)

-

The procedures in this chapter include the

(HCS).

5

See the Hazard Communication

with

bold

(MSDS).

INSTALLATION INSTRUCTION

READ THIS COMPLETELY BEFORE STARTING THE INSTALLATION `-

CAUTION:

!

and followed.

To enable the installer to make a quality installation and hold delay time to a minimum,
the following suggestions and tests should be done before the actual unit installation is

begun.

Set Satellite Docking Station in operating location and level.
It is very important that the
position.
guide when making level adjustments.
by turning the adjustable feet that support the unit.

CAUTION:

!

will

result In movement of the Satellite

Injury and/or damage to unlt.

DO NOT plug in or energize this unlt until lnstallation Instructions are read

Damage to the Unit

LEVELING THE UNIT

unit

A spirit level should be place on the top plate of the unit, at the edge, as a

Rubber feet must be Installed on each leg of the unit. Failure to do so

will

occur If the Instructions are not followed.

:

For proper unit operation,

be level when It Is standing In Its proper operating

Level the unit from left to right and front to back

Docking

Station

which

can cause personal

ELECTRICIAN’S INSTALLATION INSTRUCTIONS

WARNING ELECTRICAL SHOCK HAZARD:

!

grounded to prevent possible shock hazard.
serious Injury.

Satellite Docking Station must be properly

Electrlcal

shock

will

cause death or

The unit requires a dedicated power source capable of supplying: 120 Volt, A.C. (3) wire,
15 Amp Service.

The unit is shipped from the factory with a power cord.

INITIAL INSTALLATION INSTRUCTIONS

CAUTION:

A

Be sure all electrical connections are secure.
Plug in Satellite Docking Station
NOTE:

into electrical outlet. DO NOT plug in unit when Satellite is in place.

to flash constantly.

Position Satellite onto the Satellite Docking Station to insure light is on (there may be

a slight delay before light comes on in some models)

The Light will start flashing after the preset time is reached.

in the SS1 Instruction Manual for more information.

service technician.

Satellite Light will flash momentarily to initialize the timer when initially plugged

lnitial lnstallatlon should be performed by a qualified Installer or qualified

Improper Installation

will

damage the Satellite Docking Station.

This will cause light

See Satellite Operation Section

6

QUALITY TIMER ADJUSTMENT INSTRUCTIONS

Flashing light timer is preset from the factory for 30 minutes.

ELECTRICAL SHOCK HAZARD: Disconnect power supply to Unit before removal of any

!

!

1. Unplug unit from the electrical outlet.

2. Remove Rear panel. (See item 5 on page 8)

3. Locate time control (See item 13 on page 8) and turn

4. Replace Rear Panel.

5. Plug unit in.

panel or replacement of any component.
injury.

CAUTION: All adjustments should be made by a authorized Bloomfield Service Technician

clockwise to holding time maximum. (See Figure
NOTE:

Maximum allowable time is 120 minutes.

Electrical shock will cause death or serious

1)

To increase the holding time:

Timer Adjustment

-

Figure 1

-

I

NOTE:
is removed from the Docking Station, Satellite must be removed for more than 4 seconds for
the Timer to reset.

There is no power supplied to the satellite unless the Satellite is in place on the Unit
and the light is on.

When light is flashing, Satellite unit will maintain temperature until the Satellite

7

900014

DRIP TRAY

1 ITEM SERVICE

DESCRIPTION

QTY.

1

TOP HOUSING WLD ASSY

1 2

8718

-31

PILOT LIGHT GREEN 120V

1 3

83081

SHIELD FUNNEL

1

4

PLATE BTM TOP HOUSING

1

5

PANEL BACK

* 1 6

BODY WLD ASSY

1 7

83046

CONNECTOR ASSY

1 8

83077

HANDLE GUIDE "L"

2 9 BASE W

LD ASSY

1 10 PLATE BOTTOM

1 11

83098

LEG 4" FLANGE. BLACK

4 12

83107

FEET. RUBBER. BLACK

4 13

83102

TIMER W/SPACER

&

NUT 1 15 83105

SWITCH CHERRY W/SCREW

1 16 35-

210 STRAIN RELIEF

1 17

6407

-15

CORD ASSY

1

ACCESSORY

8

ORDERING/SERVICE PROCEDURE

Use only genuine Bloomfield replacement parts in this Satellite Docking Station.
use of replacement parts other than those supplied by Bloomfield voids the warranty.

Parts are available at your Authorized Bloomfield Service Agency as provided in your

Warranty Statement and Service Agency Listing.

To find. the parts required to restore proper operation to the Satellite Docking Station,

proceed as follows:

1.Refer to the exploded views located in this chapter to identify the parts
needed. (Page 8)

2.Use the item number from the exploded view to locate the corresponding
parts in the parts identification Table.

Ordering Information- Once the parts needed are known, record the following
information from the Identification Name Plate on the side of the Unit and
Parts Identification Section on page 8.

Model:
Part No. Description

Serial Number:

I

QtY

(Page

Part No. Description

8)

1

The

I QtY

I

I

I

I

How to order
Authorized Service Agency.

Service information
chapter, call BLOOMFIELD in the U.S. at [phone].

Be prepared to give the model and serial numbers of your Satellite Docking Station, as well
as the problem and the troubleshooting steps already taken, to the service technician when
calling for assistance.

-

For immediate shipment, call your local BLOOMFIELD INDUSTRIES

-

To obtain service assistance in addition to that contained in this

Q

I

I

TROUBLESHOOTING

A

ELECTRICAL SHOCK HAZARD: Inspecting, testing and repair of electrical equipment
should be performed only by qualified service personnel.
Station should be unplugged when servicing, except when electrical tests are
required.

it is very important, when servicing equipment to:

1. Define the basic problem

2.

Isolate the probable cause

3.

Take corrective action regarding those items hampering proper operation of

it is usually relatively easy to define the basic problem, but sometimes very difficult to
pinpoint the precise cause.

A Troubleshooting guide is provided in this manual to suggest probable causes and
corrective actions for each.
proper operation of the equipment cannot be restored.

Should the problem remain after exhausting the troubleshooting steps suggested, refer
to the Order/Service information section of this chapter. (page

Electrical shock

the equipment.

will

cause

Obviously, if the cause is not isolated and corrected,

serious

Injury or death.

The Satellite Docking

9)

-

!

ELECTRICAL SHOCK HAZARD: Use extreme care during electrical circuit test. Live
circuits will be exposed. Electrical shook will cause serious injury or death.

10

TROUBLESHOOTING

[

PROBLEM ][ PROBABLE CAUSE]

Quality light lo not
on/flashing when
Satellite is in place.

Quality light stays
on when Satellite is
not in place.

Quality light flashes
constantly

Satellite Receptical or SDS-l
Connector

Snap Action
Satellite is not in proper position

Snap Action Switch Snap Action switch on Connector should open when Satellite is

Satellite is still in place
Satellite was in place when

timer

initialized

Quality Timer

Switch

in Connector Check continuity, replace if defective.

CORRECTIVE ACTION

Check Receptical and Connector Assembly, make sure all pins are
tight and in place.
Check ail soldered wiring.
Check continuity, replace if defective.

Place Satellite unit in proper position, making sure the, bottom dimples

on Satellite base are located on the matching dimples on the Brewer.

removed from position, shutting off the light. if not, replace Switch.

Remove Satellite for more than 4 seconds for timer to reset.
Remove Satellite, Unplug unit for more than 4 seconds. Plug unit in

(with

Satellite removed)

Remove Satellite, Unplug unit for more than 4 seconds. Plug unit in

(with

Satellite removed) If unit

~

still

flashes, replace Quality timer.

I‘

11

SCHEMATIC & WIRING DIAGRAM

(MODEL SDS-1)

MODEL: VOLTS WATTS:

SDS-1 120 45 W (USE WITH [1] 9105DS OR 9105DP)

12

13