Bloomfield IRCS2-ND Installation Manual

IL2832

Conveyor Toasters Installation Instructions

These symbols are intended to alert the
user to the presence of important operating
and maintenance instructions in the manual
accompanying the appliance.

Go to:

www.star-mfg.com/scripts/manuals.aspx

to obtain this units installation & operations

manual, warranty & other documents.

NOTICE

Using any part other than genuine Holman factory supplied parts
relieves the manufacturer of all liability.

Holman reserves the right to change specications and product

design without notice. Such revisions do not entitle the buyer to
corresponding changes, improvements, additions or replacements
for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies

and regulations, the specications contained in this sheet are subject

to change without notice. While Holman Manufacturing exercises
good faith efforts to provide information that is accurate, we are
not responsible for errors or omissions in information provided

or conclusions reached as a result of using the specications.

By using the information provided, the user assumes all risks in
connection with such use.

CAUTION

This equipment is designed and sold for commercial use only by
personnel trained and experienced in its operation and is not sold
for consumer use in and around the home nor for use directly by
the general public in food service locations.

Before using your new equipment, read and understand all the
instructions & labels associated with the unit prior to putting it into
operation. Make sure all people associated with its use understand
the units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both
visible and concealed. This unit has been tested and carefully
packaged to insure delivery of your unit in perfect condition.
If equipment is received in damaged condition, either apparent or
concealed, a claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until
after equipment is unpacked, a request for inspection of concealed
damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials
for inspection. The carrier will make an inspection and will supply
necessary claim forms.

GENERAL SAFETY INFORMATION

MODEL

IRCS2-ND

Inpingment Conveyor Toasters

Electronic Controls

GENERAL INSTALLATION INFORMATION

The unit was shipped fully assembled and ready to plug into a

standard outlet specied for its voltage and amp draw. If improper
electrical supply is determined, contact a qualied electrician prior

to using the unit. Removal and replacement of the power cord
and plug will void the warranty. For assistance, contact your local
authorized service agent for service or required maintenance.

Level unit using the adjustable feet under the unit (approximately
1/2" adjustment).

Before using the unit for the rst time, wipe down the exterior with

a damp cloth.

Allow enough space around the toaster for adequate ventilation.
Do not operate the unit without the crumb tray properly positioned.
Overheating and poor toasting may occur. Read all labels on the
unit and follow their instructions.

MAINTENANCE AND REPAIRS

Contact the factory, a service representative or a local
service company for service or required maintenance.

Go to www.star-mfg.com/scripts/manuals.aspx to nd a service

agent near you. Replacement cord sets must be purchased from
Star Manufacturing International, Inc. or our authorized agents.

Should you need any assistance regarding the operation or
maintenance of any Holman equipment; write, phone, fax or
e-mail our service department. In all correspondence mention
the model number and the serial number of your unit, along with
the voltage.

Business Hours: 8 am to 4:30 p.m. Central Standard Time

Telephone: [phone]

Fax: [phone]

E-mail: [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A.

2M-Z18705, Rev. - 6/04/2014

ELECTRICAL CONNECTION

Before making any electrical connection to this unit,
check that the power supply is adequate for the voltage,
amperage and requirements stated on the rating plate.
A wiring diagram is included in the Installation &
Operations manual, which can be downloaded at

www.star-mfg.com/scripts/manuals.aspx.

Disconnect the unit from the power source before installing or
removing any parts.

Be absolutely sure that the ground connection for the receptacle is
properly wired. Do not connect equipment to power without proper
ground connections. Improper grounding may result in personal

injury or fatality.

DO NOT CUT OR REMOVE THIS PLUG OR

WARNING

WARNING

CAUTION

WARNING

GROUNDING PRONG FROM THE PLUG.

CONNECT/PLUG UNIT INTO DEDICATED
A.C. LINE ONLY SPECIFIED ON THE DATA

PLATE OF THE UNIT.

CERTAIN SURFACES ARE EXTREMELY HOT
DURING OPERATION AND CARE SHOULD
BE TAKEN WHILE USING THIS UNIT.

DO NOT IMMERSE OR LET THE UNIT STAND
IN WATER.

ELECTRONIC

RADIANT-IMPINGEMENT SYSTEM

T1 T2

T3 T4

T5 T6

SAVER

TOP HEAT

BOTTOM HEAT

CONVEYOR SPEED

ON

OFF

The Holman IRCS conveyor toaster
comes with pre-programmed factory
default settings for ALL MENU
BUTTONS.

Factory default settings are as follow:

IRCS2-SBD DEFAULT

SETTINGS

Menu

Buttons

T1

Top

Heat

Bottom

Heat

Conveyor

Speed

45

T2 87

T3 23

8 10

T4 90

T5 70

T6 99

DO NOT HOSE DOWN THE UNIT OR THE
TABLE/COUNTER IF THE UNIT IS ON THE

WARNING

TABLE/COUNTER.

KEEP AWAY FROM RUNNING WATER.

WARNING

INSTALLATION REQUIREMENTS

1. Space: 10”x29”x17.5” (width x depth x height) in

Specialty Board of Breakfast Toaster Cart

2. Electricity: 208/240 Volts, 11.5 Amps, NEMA 6-30R
Recepticale

NEMA 6-30R

NOTE: Ensure to clean the toaster properly before

using it for the rst time. Refer to the Cleaning

Procedure document for cleaning instructions.

IL2711

POWER SAVER SWITCH

There are three Power Saver modes:

ON: Unit is in pre-programmed power saving setting.
OFF: Power Saver mode is turned off.
AUTO ON: Power Saver turns on when there has been no activity

for a programmed length of time.

The operator may adjust the level of power reduction for the saver

mode. (Note: conveyor may move slowly when in saver mode.)

Two buttons (+) and (-) are used when increasing or decreasing the

value of each programmable setting.

A red LED light located at the lower portion of the control panel label
will indicate if the value for top heat, bottom heat or conveyor speed

is being adjusted.

CERTAIN SURFACES ARE EXTREMELY HOT
DURING OPERATION AND CARE SHOULD

CAUTION

BE TAKEN WHILE USING THIS UNIT.

START UP

When the toaster has been plugged into a suitable outlet and power
supply, the word OFF will be displayed on the L.E.D. read out.

A. Press the ON/OFF button once to turn on the toaster. The

toaster will now enter into pre-heat and “PREHT” will be

displayed (the elements will begin to glow but the conveyor
and fan motor will not turn on).

B. After one minute, the fan motor will turn on and the conveyor

will begin turning at the previously saved setting (for initial

start up, the drive motor will operate at the factory default

setting).

C. After 14 minutes, the display will show the last used program

selection i.e. (for initial startup, CROIS, MUFFIN, will be the
last program selected).

DAILY OPERATION

Check the power cord to insure that it is plugged into a proper
outlet.

Press the ON/OFF button once to turn the toaster on.
Press the button a second time to turn the toaster off.

NOTE: When the toaster is turned off, the fan and conveyor motors

will continue to run for ve minutes. The words COOL and DOWN will
be alternately displayed during that time. After ve minutes, the word

OFF will be displayed until the ON/OFF button is pressed again.

Once the toaster has been pre-heated, the menu buttons can be
pressed to change to T1, T2, T3, T4, T5, T6

OPERATING HINTS AND SAFETY

IMPORTANT: If “HIGH TEMP” shows on the display

1. Turn off the toaster and allow it to fully cool down.

2. Inspect the fan inlet on the bottom of the toaster
and remove anyting blocking the cooling fan inlet.

3. Press the red high temperaure limit reset button on
the back of the toaster. (Note: There is one reset

on each side). (Note: the toaster must be fully cool
in order for the limit switch to reset).

4. Turn on the toaster and check for proper operation.

5. If cleaning the cooling fan inlet does not correct
the problem, contact the factory or an authorized
service agency for required maintenance.

Disconnect power to the unit with the ON/OFF button at the end of
each day of operation.

Do not leave the unit in operation without an attendant.

Do not leave the unit at high temperature when not in use or during

idle periods. This will cause food particles and grease lm to

carbonize.

The cooling fan will continue to run until the toaster has completely
cooled. If the toaster MUST be moved after using, allow the cooling
fan to turn OFF before unplugging.

PROGRAMMING

A. CONVEYOR SPEED (temporary setting)

The conveyor speed is programmable with a range from 1 to 99 with
1 being the slowest and 99 being the fastest. Each menu item can
have independent conveyor speed settings.

B. PROGRAMMING VALUES FOR MENU ITEMS

To make a program change to the top & bottom elements, or conveyor

speed, you must rst be in the menu item you want changed.

Example: to change the programmed conveyor speed for croissants,
the display must read CROIS. To change the programmed conveyor
speed for MUFFIN, the display must read MUFFIN and so on for
each menu item.

1) Select the menu item you want to change i.e. T1, T2, T3, T4,

T5 or T6.

2) Press and hold both ( + ) AND ( - ) buttons for 3 seconds until

the display goes blank, release the buttons and the display
will show three characters for the menu item elected and the
last two characters for the current value setting, i.e. T1, T2,
T3, T4, T5 of T6. The red L.E.D. light for upper front element

at the bottom of the label will ash.

3) Press the ( + ) or ( - ) buttons to increase or decrease the

setting for the upper element.

4) Press the program button for the menu button again and the
red L.E.D. for the up lower element will ash.

5) Press the ( + ) or ( - ) buttons to increase or decrease the

setting for the lower element.

6) Press the button for the menu button again and the red L.E.D.
for the conveyor speed will ash.

7) Press the ( + ) or ( - ) buttons to increase or decrease the

setting for the conveyor speed.

8) To skip one feature setting with out making any changes,

press the menu item button one time and the red L.E.D. light

for the next item will now ash.

9) To change the POWER SAVER values press the SAVER
button or to save your new setting(s), and exit the program

mode press the menu button.

10) The last two characters in the display will show MN for
minutes.

11) The rst three characters will be numerical to represent the

time setting.

12) When set to “OFF” the Saver button will be disabled during

operation. The PowerSaver can be set to “OFF” or using the

( + ) or ( - ) set the time from 15 to 480 minutes.

13) Press the SAVER button to change the power reduction using
the ( + ) or ( - ) buttons to increase or decrease the setting.

14) Press the POWER SAVER button to save changes and to

exit.