Bloomfield HT-500AF Installation Instructions Manual

ELECTRICAL

INSTALLATION INSTRUCTIONS

DROP-IN BAIN MARIE STYLE HEATED TANK

MODEL HT-500AF WITH WATER FILL

WATTSVOLTSMODEL

HT-500AF

240HT-500AF

UNITS ARE SHIPPED THREE PHASE AND ARE FIELD CONVERTIBLE TO SINGLE PHASE

70 1/2
(1791)

16 7/8

(429)

4500208
6000

3 1/8

(79)

AMPS PER LINE 3 PHASE

13.0

4 1/8
(105)

5

(127)

18.7

21.7

22 7/8

(581)

AMPS

L3L2L1

8.7

10.0

SINGLE

PHASE

25.015.0

PRODUCT DIMENSIONSCUTOUT DETAILS

3 7/8

(98)

1/4 NPT WATER
FILL CONNECTION

FIELD WIRING GAUGE

3 PHASE 1 PHASE

10 AWB Cu21.7

67 3/4

(1721)

71 1/2
(1816)

(457)

6 1/4

(159)

18

8 AWB Cu
8 AWB Cu

19 7/8

(505)

9 3/4
(248)

CONTROL PANEL WITH
FLEXIBLE CONDUIT

TEMP.

RATING

90°C
90°C10 AWB Cu

23 5/8

(600)

1 INCH NPT DRAIN
WITH BALL VALVE

CLEARANCES

INCHES

(MM)

INSTALLATION INSTRUCTIONS

INSTALLER MUST MEET CONDITIONS OF ACCEPTABILITY
OUTLINED BELOW UPON INSTALLATION:

1. Required installation clearances:
Wooden and Metal Installation: DO NOT install closer than
4 1/8 inches to front wall, 1 inch to back and side walls,
and 6 3/4 inches to surface below the unit.

2. Unit shall be accessible for servicing from the bottom.

3. If storage is to be used underneath the unit, it is
recommended that a baffle be placed 8 1/2 inches below
the unit to avoid contact with elevated temperatures.

4. For water and waste connections: This appliance is to be
installed to comply with the applicable federal, state or
local plumbing codes.

TO FABRICATE:

1. Lay out "cutout" dimensions on countertop and front
apron.

2. Lay out and fabricate control panel holes in counter
apron using the control box as a template.

3. Cut out holes.

TO INSTALL:

IMPORTANT - DO NOT disconnect lead wires from the
Master Control Panel when making installation.

1. Tilt and pass Control Panel and electrical box through
the countertop cutout, then through the apron cutout.
Lower modular section into countertop cutout and
position.
RECOMMENDATION: Before final seating of modular section
to countertop, apply a bead of silicone adhesive/sealant
to the underside of gasket supplied on the mounting
flange.

2. From underneath, insert screwdriver into slots in
Wellslock frame and twist ears outward (clockwise) as
required to secure flange tightly to countertop.

3. Mount Control Box to apron cutout as shown in drawing.

4. Mount Control Panel onto electrical box using the
screws supplied.

WELLS/BLOOMFIELD * VERDI, NV

MINIMUM CLEARANCE REQUIRED

FROM UNIT TO THE NEAREST SURFACE

FRONTBOTTOMSIDEBACK

11

(25)

WARMER FLANGE

GASKET

SCREWDRIVER

TO PLUMB:

1. A drain with valve is supplied on all units. Location of the
valve handle is at the discretion of the fabricator (see drawing).

2. Connect 1" drain connection to a suitable drain line.

3. Connect 1/4 NPT flexible water fill line to solenoid valve in
outlet box, maximum pressure 120 PSI, maximum temperature 120°F.

COUNTERTOP

MASTER CONTROL PANEL

WELLSLOK

6 3/4

(171)(25)

1/4 NPT WATER
FILL CONNECTION

4 1/8

(105)

TO WIRE:

1. Final connection is accomplished by bringing proper power
supply leads (see 'WIRING REQUIREMENTS' label) through
conduit knockout to terminal block supplied within the Master
Control Panel. Check nameplates for voltage and phase.

NOTES:

BAIN MARIE STYLE HEATED TANKS ARE DESIGNED FOR WET
OPERATION ONLY.

A BACK FLOW PREVENTER IS INCORPORATED IN THE WATER FILL
LINE BETWEEN SOLENOID VALVE AND PAN. LOCAL CODES MAY
REQUIRE AN ADDITIONAL VACUUM BREAK DEVICE, NOT PROVIDED
BY WELLS.

INSTALLATION MUST MEED LOCAL PLUMBING AND ELECTRICAL
CODES.

301779-4 REV (-)