Bloomfield 9010, 9011, 9012, 9013, 9016 Operation Manual
...
OWNER'S MANUAL
2
ERIK CIRCLE, P.O.Box
280
Form No.
70447
Rev. B
M602
082300
cps
INTEGRITY®
Coffee
Brewing System
602
OPERATING INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
and
PARTS LIST
DOMESTIC MODEL NOS.
9010
9013
9011
9016
9012
9017
Verdi, Nevada 89439
telephone (888) 492-2782
fax (888) 492-2783
www.wellsbloomfield.com
LIMITED WARRANTY STATEMENT
All electrical equipment manufactured by BLOOMFIELD INDUSTRIES is warranted against defects in materials and workmanship for a period
of one year from the date of original installation or eighteen (18) months from the date of shipment from our factory, whichever comes first, and
is for the benefit of the original purchaser, except that:
a. airpots carry a 30 day parts warranty only.
b. dispensers; i.e., tea and coffee carry a 90 days parts warranty only, excludes decanters.
THIS WARRANTY IS THE COMPLETEAND ONLY WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN FACT, INCLUDING BUT NOT
LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, AND/OR FOR DIRECT,
INDIRECT OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH BLOOMFIELD INDUSTRIES PRODUCTS.
This warranty is void if it is determined that upon inspection by an Authorized Service Agency that the equipment has bee modified, misused,
misapplied, improperly installed, or damaged in transit or by fire, flood or act of God.
It also does not apply if the serial nameplate has been removed or service is performed by unauthorized personnel. The prices charged by
Bloomfield Industries for its products are based upon the limitations in this warranty. Seller's obligation under this warranty is limited to the
repair of defects without charge by a Bloomfield Industries Authorized Service Agency or one of its sub-service agencies. This service will be
provided on customer's premises for non-portable models. Portable models (a device with a cord and plug) must be taken or shipped to the
closest Authorized Service Agency, transportation charges prepaid for services.
In addition to restriction contained in this warranty, specific limitations are shown below (Additional Warranty Exclusions).
Bloomfield Industries Authorized Service Agendes are located in principal cities. This warranty is valid in the United States and void elsewhere.
Please consult your classified telephone directory, your food service equipment dealer or for information and other details concerning warranty
write to:
Service Parts Department, Bloomfield Industries, P.O. Box 280 Verdi, NV 89439 Phone: (888) 492-2782 Fax: (888) 492-2783
SERVICE POLICY AND PROCEDURE GUIDE
ADDITIONAL WARRANTY EXCLUSIONS
1. Resetting the safety thermostats, circuit breakers or overload protectors unless warranted conditions are the cause.
2. All problems due to operation at voltage other than specified on equipment nameplates are not covered under warranty. Conversion to
correct voltage must be the customer's responsibility.
3. All problems due to electrical connections not made in accordance with electrical code requirement and wiring diagrams supplied with
the equipment are not covered under warranty.
4. Replacement of items subject to normal wear, to include such items as knobs and light bulbs. Normal maintenance functions including
adjustments of thermostats, and replacement of indicating lights are not covered under warranty.
5. Failure to fill the brewer with water prior to applying electrical power will damage the unit and is not covered under warranty. Also, all
problems due to inadequate water supply, such as fluctuating, high or low water pressure, etc. are not covered by warranty.
6. All problems due to mineral/calcium deposits, or contamination from chlorides/chlorines. De-liming is considered a preventative
maintenance function and not covered by warranty.
7. Full use, care and maintenance instructions are supplied with each machine. Those miscellaneous adjustments noted are customer
responsibility. Proper attention will prolong the life of the machine.
8. Travel mileage is limited to sixty (60) miles from an authorized Service Agency or one of its sub-agencies. Portable equipment (units with
a plug and cord) must be taken or shipped freight prepaid to an Authorized Service Agency for warranty service.
9. All labor shall be performed during normal working hours. Overtime premium will be charged to customer.
10. All genuine Bloomfield replacement parts are warranted for ninety (90) days from date of purchase on non-warranty equipment. Any use
of non-genuine Bloomfield parts completely voids any warranty.
11. Installation, labor, and job check-outs are not considered warranty.
12. Charges incurred by delays, waiting time or operating restrictions that hinder the service technician's ability to perform service are not
covered by warranty. This includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel prior to
leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt, and that the
note of loss or damage is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of damage.
3. CONCEALED LOSS OR DAMAGE: If damage is unnoticed until the merchandise is opened, notify the transportation company o
carrier immediately, and file a "CONCEALED DAMAGE" claim with them. This should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the container for inspection.
Wells manufacturing cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the
necessary documents to support your claim.
xi
TABLE OF CONTENTS
Warranty
Inside Cover
Specifications
1
Features and Operating Controls
Old Style Solenoid
2
New Style Solenoid
4
Installation Instructions
6
Servicing Instructions
Temperature Adjustment
8
Timing Adjustment
8
Water Flow Diagram
9
Trouble Shooting
10
Wiring Diagrams
11
Exploded Views/ Parts Lists
Electrical Components
12
Hot Water Tank Assembly
13
Internal Plumbing Components
14
9016
Automatic, Plumbed
-
In, 3 Warmer
n/a YES
115/230V/1800W
Brewing Coffee 7
Cabinet & Related Components 15
SPECIFICATIONS
MODEL CONFIGURATION PLUG FAUCET VOLT/WATTAGE
9010 Automatic, Plumbed-In, 3 Warmer NEMA5-20P YES 120V/2300W
9011 Automatic, Plumbed-In, 3 Warmer NEMA5-20P NO 120V/2300W
9012 Automatic, Plumbed-In, 3 Warmer NEMA5-15P YES 120V/1800W
9013 Automatic, Plumbed-In, 3 Warmer NEMA5-15P NO 120V/1800W
9017 Automatic, Plumbed-In, 3 Warmer n/a NO 115/230V/1800W
In this manual, brewers manufactured prior to April, 2000 will be identified as "old-style solenoid". Such brewers were
manufactured with a metal-bodied solenoid.
Brewers manufactured from April, 2000 will be identified as "new style solenoid". Such brewers are manufactured
with a nylon-bodied solenoid having either: a single controlled outlet; or, a single controlled outlet and a straight -thru
(bypass) outlet.
Unless otherwise noted, all drawings and procedures in this manual refer to brewers with the new style solenoid.
1
WATER SYSTEM (Old Style Solenoid,
manufactured prior to April, 2000)
2
3. WARMER COVER PLATE 48. OUTLET ELBOW
3m. Main Warmer 49. VENT TUBE
3f. Top Front Warmer 50. WATER INLET ELBOW
3r. Top Rear Warmer 51. HI-LIMIT THERMOSTAT
7. HOLD DOWN STRAP 52. TANK COVER
9. ELBOW, VENT LINE 54. WATER INLET TUBE
10. BASIN PAN 56. HEATING ELEMENT
11. WATER OUTLET TUBE 57. TANK LID GASKET
12. SPRAYER ELBOW 61. FAUCET FORMED INLET TUBE
18. FAUCET ASSEMBLY 62. FAUCET FORMED OUTLET TUBE
19. WARMER ON/OFF SWITCH 63. ADAPTER
19m. Main Warmer 64. FAUCET NEEDLE VALVE
19f. Top Front Warmer x6
19r. Top Rear Warmer 66. CORD & CAP ASSEMBLY
20. INDICATOR LIGHT 69. FAUCET HOT WATER COIL
21. START SWITCH - BREW 70. TANK BODY
26. SPRAY HEAD GASKET 75. BREW CHAMBER
27. SPRAY DISK 77. BASIN COVER ASSEMBLY
x29. ELBOW 80. TIMER ACCESS BUTTON PLUG
x30. SOLENOID VALVE W/ FLOW CONTROL
x33. REDUCER C. DECANTER (NOT PROVIDED, SHOWN FOR
x34. TEE
x38. ADAPTER R. RESERVOIR ACCESS (COLD WATER POURED
39. WATER INLET HOSE
x41. INLET FITTING
44. TIMER, 2-MIN. x = Brewers manufactured prior to April, 2000
47. THERMOSTAT
3
FAUCET SUPPLY BRAIDED HOSE
LOCATION ONLY)
IN HERE FOR POUR-OVER FUNCTION)
OPERATING FEATURES AND CONTROLS NEW -
WATER SYSTEM
STYLE SOLENOID
4
(New Style Solenoid,
Manufactured April, 2000 and later)
Loading...