WELLS BLOOMFIELD, LLC
2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439
telephone: 775-689-5707
www.wellsbloomfield.com
fax: 775-689-5976
763
OPERATION MANUAL
For
Hot Plate-Style
Model 8702
Model 8852
Decanter W armer
MODELS
8708 Dual In-Line Warmer
8851 Single Warmer
8852 Dual Warmer
8871 Single Warmer
8872 Dual Warmer
Includes:
Installation
Use & Care
Model 8871
NOTE: All warmers shown with optional 8900-Series
Glass Decanters (available separately).
PRINTED IN CHINA
p/n 77719 Rev. (-) ECN-13409 M763 080124 cps
WARRANTY STATEMENT
Carafe Warmer models 8708, 8851, 8852, 8871
and 8872 manufactured by Wells Bloomfield, LLC
are warranted against defects in material and
workmanship for a period of ninety (90) days from
original purchase
original purchaser.
THIS WARRANTY IS THE COMPLETE AND
ONLY WARRANTY, EXPRESSED OR IMPLIED
IN LAW OR IN FACT, INCLUDING, BUT NOT
LIMIT E D T O , WARRA N T I E S O F
MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE, AND/OR INDIRECT
OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD
PRODUCTS.
,
and is for the benefit of the
This warranty is void if it is determined upon
inspection by the factory that the equipment has
been modified, misused, misapplied, improperly
installed, or damaged in transit or by fire, flood or
act of God.
It also does not apply if the serial nameplate has
been removed or service is performed by
unauthorized personnel.
This warranty is valid in the United States and
Canada and void elsewhere.
In addition to restrictions contained in this
warranty, specific limitations are detailed in the
ADDITIONAL WARRANTY EXCLUSIONS section.
Please contact:
Bloomfield Service Department for all warranty
claims:
Phone: 775-689-5400
Fax: 775-698-5976
SERVICE POLICY AND PROCEDURE GUIDE
1. All problems due to operation at voltages
other than specified on equipment name
plates-conversion to correct voltage must be
the customer's responsibility.
2. All problems due to electrical connections not
made in accordance with electrical code
Additional Warranty Exclusions
requirements and wiring diagrams supplied
with the equipment.
3. Replacement of items subject to normal wear.
Normal maintenance functions are not
covered under warranty.
4. Proper attention, full care and maintenance
will prolong the life of the machine.
SHIPPING DAMAGE CLAIMS PROCEDURE
SHIPPING DAMAGE CLAIMS PROCEDURE
Note: For your protection, please note that the
equipment in this shipment was carefully inspected
and packaged by skilled personnel before leaving
the factory. Upon acceptance of this shipment, the
transportation company assumes full responsibility
for its safe delivery.
If Shipment arrives damaged:
1. Visible loss or damage: Be certain that any
visible loss or damage is noted on the freight
bill or express receipt, and that the note of
loss or damage is signed by the delivery
person.
2. File claim for damage immediately:
Regardless of the extent of the damage.
3. Concealed loss or damage: if damage is
unnoticed until the merchandise is unpacked,
notify the transportation company or carrier
immediately, and file "Concealed Damage"
claim with them. This must be done within
fifteen (15) days from the date the delivery
was made to you. Be sure to retain the
container for inspection.
Bloomfield Industries cannot assume liability for
damage or loss incurred in transit. We will,
however, at your request, supply you with the
necessary documents to support your claim.
xi
763 p/n 77719 OpManual Decanter Warmers
TABLE OF CONTENTS
WARRANTY STATEMENT xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS 2
PRECAUTIONS & GENERAL INFORMATION 3
AGENCY LISTING INFORMATION 3
INSTALLATION INSTRUCTIONS 4
OPERATION 6
BREWING COFFEE 8
CLEANING INSTRUCTIONS 9
TROUBLESHOOTING SUGGESTIONS 10
SERVICING INSTRUCTIONS 11
Deliming Instructions 16
EXPLODED VIEWS & PARTS LISTS 18
SERVICE KITS 22
WIRING DIAGRAMS 23
Thank You for purchasing this
Wells Bloomfield appliance.
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this appliance, and to use,
care for the appliance in a manner
which will ensure its optimum
performance.
SPECIFICATIONS
MODEL STYLE VOLTS 1ø WATTS AMPS POWER SUPPLY CORD
8708
8851
Dual Step-Up 200 1.7 NEMA-5-15P
Single 100 0.8
120 VAC
120 VAC
NEMA-5-15P
8852
8871
8872
Dual 200 1.7
Single 100 0.8
Dual 200 1.7
120 VAC
120 VAC
120 VAC
NEMA-5-15P
NEMA-5-15P
NEMA-5-15P
Decanter warmers operate at a warming temperature of approximately 185ºF ± 10ºF (85 ºC ± 6ºC).
763 p/n 77719 OpManual Decanter Warmers
1
FEATURES AND OPERATING CONTROLS
POWER CORD
WARMER PLATE
WARMER SWITCH
" I " INDICATES "ON"
"O" INDICATES "OFF"
Fig. 1 Features & Operating Controls
Model 8852 shown. Features are similar for all models.
OPTIONAL DECANTER
(SHOWN FOR POSITION
ONLY)
SLIP-RESISTANT FEET
763 p/n 77719 OpManual Decanter Warmers
2
PRECAUTIONS AND GENERAL INFORMATION
WARNING: ELECTRIC SHOCK HAZARD
All servicing requiring access to non-insulated components must be performed by qualified
service personnel. Do not open any access panels which require the use of tools.
Failure to heed this warning can result in electrical shock.
WARNING: INJURY HAZARD
All installation procedures must be performed by qualified personnel with full knowledge of all
applicable electrical codes. Failure could result in property damage and pe rsonal injury.
WARNING: ELECTRIC SHOCK HAZARD
Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a
plumbing line will provide such a ground. Electrical shock will cause death or se rious injury.
This appliance is intended for indoor commercial use only.
This appliance is intended for use to maintain the temperature of
hot liquids beverage products for human consumption. No other
use is recommended or authorized by the manufacturer or its
agents.
This appliance is intended for use in commercial establishments,
where all operators are familiar with the appliance use,
limitations and associated hazards. Operating instructions and
warnings must be read and understood by all operators and
users.
The following trouble shooting, component views and parts lists
are included for general reference, and are intended for use by
qualified service personnel.
This manual should be considered a permanent part of this
appliance. The manual must remain with the appliance if it is
sold or moved to another location.
CAUTION:
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and followed.
Damage to the warmer may occur
if these instructions are not
followed.
CAUTION:
BURN HAZARD
Exposed surfaces of the warmer
may be HOT to the touch.
The warmer plate will be very hot
during operation and can cause
serious burns on contact.
Do not discard this
appliance as usual
trash at the end of its
useful life.
Recycle properly.
AGENCY LISTING INFORMATION
This warmer is listed under UL file E9253.
763 p/n 77719 OpManual Decanter Warmers
This brewer meets
CUS
Standard 4 only when installed,
operated and maintained in accordance with the enclosed
instructions.
3
CUS
LISTED E9253
STD 4
INSTALLATION INSTRUCTIONS
READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION
CAUTION:
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and
followed.
Damage to the Brewer will occur
if these instructions are not
followed.
CAUTION:
UNSTABLE
It is very important for safety and
for proper operation that the
brewer is level and stable when
standing in its final operating
position. Provided adjustable,
non-skid legs must be installed at
each corner of the unit.. Failure to
do so will result in movement of
the brewer which can cause
personal Injury and/or damage to
brewer.
EQUIPMENT HAZARD
WARNING:
SHOCK HAZARD
Brewer must be properly
grounded to prevent possible
shock hazard. DO NOT assume
a plumbing line will provide such
a ground. Electrical shock will
cause death or serious injury.
IMPORTANT:
The ground prong of the plug is
part of a system designed to
protect you from electrical shock
in the event of internal damage.
Never cut off the ground prong
nor twist a blade to fit an
existing receptacle. Contact a
licensed electrician to install the
proper circuit and receptacle.
Unpack the unit. Inspect all components for completeness and
condition. Ensure that all packing materials have been removed
from the unit.
Verify that the Spray Head Gasket and Spray Disk are properly
installed.
LEVELING THE UNIT
Verify that slip-resistant foot is installed at each corner of the
warmer.
Set warmer in its operating location. Level the warmer. A spirit
level should be placed on the top of the unit, at the edge, as a
guide when making level adjustments.
ELECTRICIAN’S INSTALLATION INSTRUCTIONS
REFER TO ELECTRICAL SPECIFICATIONS - Page 1
Check the nameplate to determine correct electrical service
required for the Brewer to be installed.
Warmer models 8708, 8851, 8852, 8871 and 8872 are
equipped with a cord and plug. They require a 115 - 125 volt
15 amp circuit (50/60 Hz, 2 wire plus ground, with NEMA 5-15R
receptacle).
763 p/n 77719 OpManual Decanter Warmers
4
OPERATION
Place a decanter of hot beverage on a warmer plate.
Press warmer switch for that warmer plate to ON ( I ).
Press warmer switch to OFF (O) when a warmer plate is not in
use for any extended period.
SUGGESTION: Coffee loses its fresh flavor if allowed to set on a
warmer for too long. Discard stale coffee promptly.
DO NOT allow an empty decanter to set on a hot warmer. This
will damage the decanter. Discard any decanter that has been
allowed to boil dry.
Disconnect warmer from electric power if unused for prolonged
periods (i.e. overnight).
PROCEDURE: Clean Coffee Warmer
PRECAUTIONS: Disconnect warmer from electric power.
Allow warmer to cool.
FREQUENCY: Daily
TOOLS: Mild Detergent, Clean Soft Cloth or Sponge
1. Disconnect warmer from electric power.
Allow warmer to cool before cleaning.
Remove decanters.
2. Wipe the warmer plates with a sponge dampened with warm
water and a mild detergent. Rinse with clean water and
allow to air dry.
3. Wipe the exterior of the warmer with a soft clean cloth or
sponge moistened with clean water and allow to air dry.
Procedure is complete
CAUTION:
BURN HAZARD
Exposed surfaces of the warmer
may be HOT to the touch.
The warmer plate will be very hot
during operation and can cause
serious burns on contact.
CLEANING INSTRUCTIONS
CAUTION:
BURN HAZARD
Brewing and serving
temperatures of coffee are
extremely hot. Hot coffee will
cause serious skin burns.
CAUTION:
SHOCK HAZARD
Do not submerge or immerse
warmer in water.
Do not pour or splash water onto
switches or wiring.
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean the
warmer.
763 p/n 77719 OpManual Decanter Warmers
5
Genuine Parts
Protect - YOU - All - Ways
SERVICE TRAINING - QUALITY SERVICE
CUSTOMER SATISFACTION
Commercial Food Equipment Service Association
Wells Bloomfield proudly supports CFESA
Commercial Food Equipment Service Association
SERVICE TRAINING - QUALITY SERVICE
CUSTOMER SATISFACTION
WELLS BLOOMFIELD, LLC
2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439
telephone: 775-689-5707
fax: 775-689-5976
www.wellsbloomfield.com
PRINTED IN CHINA
Loading...